Matrix solid phase dispersion-assisted BCR sequential extraction method for metal partitioning in surface estuarine sediments

The BCR (the Community Bureau of Reference) of the European Union sequential extraction scheme for metal partitioning in estuarine sediments has been accelerated by using a matrix solid phase dispersion (MSPD) approach. The MSPD assisted BCR procedure consists of passing the extractants proposed by conventional BCR protocol (0.11 M acetic acid, 0.1 M hydroxylammonium chloride and 8.8 M hydrogen peroxide plus 1 M ammonium acetate) through the dispersed sample packaged inside a disposable syringe. Different silica-, magnesium- and aluminium-based materials were tested as dispersing agents and sea sand was found to offer the best performances. Variables for assisting the three stages of the BCR protocol were optimized, and accurate results were obtained when assisting the first and the third stages (exchangeable and oxidizable fractions, respectively). However, lack of accuracy was observed when assisting the second step (reducible fraction) and this result agrees with most of the assisted BCR procedures for which extracting the reducible fraction is the most troublesome stage. The organic matter oxidation (third stage) was successfully assisted by passing hydrogen peroxide at 50 °C through the dispersed sample inside de syringe just before passing ammonium acetate. Therefore, the time-consuming and unsafe conventional organic matter oxidation processes, commonly performed even for microwave/ultrasounds assisted BCR procedures, are totally avoided. Inductively coupled plasma-mass spectrometry (ICP-MS) was used as a selective detector. The target elements were Cd, Co, Cr, Mn, Ni, Sr and Zn (first stage), Cd, Co and Ni (second stage), and Co, Cr, Mn, Ni, Sr and Zn (third stage). Repeatability of the method (n = 7) was good, and RSDs values of 9, 10, 10, 8, 8, 3 and 8% was obtained for Cd, Co, Cr, Mn, Ni, Sr and Zn, respectively (first stage); 10, 9 and 9% for Cd, Co and Ni, respectively (second stage); and 6, 2, 3, 4, 7 and 9% Co, Cr, Mn, Ni, Sr and Zn, respectively (third stage). The procedure was also validated by analysing two certified reference materials (CRM 601 and CRM 701). Good accuracy was obtained for the target elements extracted at the first stage: Cd (4.0 ± 0.1 and 7.3 ± 0.09 μg g⁻¹ in CRM 601 and CRM 701, respectively), Cr (0.36 ± 0.008 and 2.21 ± 0.08 μg g⁻¹ in CRM 601 and CRM 701, respectively), Ni (8.0 ± 0.3 and 15.4 ± 0.3 μg g⁻¹ in CRM 601 and CRM 701, respectively) and Zn (262 ± 3 and 203 ± 3 μg g⁻¹ in CRM 601 and CRM 701, respectively). Also, good accuracy was observed for elements extracted at the third step: Cd (1.8 ± 0.09 and 0.29 ± 0.03 μg g⁻¹ in CRM 601 and CRM 701, respectively), Cr (145 ± 4 μg g⁻¹ in CRM 701), Ni (8.2 ± 0.7 and 15.1 ± 0.5 μg g⁻¹ in CRM 601 and CRM 701, respectively) and Zn (45 ± 0.7 μg g⁻¹ in CRM 701).     

Validation of a new high‐throughput method to determine urinary S‐phenylmercapturic acid using low‐temperature partitioning extraction and ultra high performance liquid chromatography–mass spectrometry

A new highly sensitive and environmentally friendly analytical method, using low‐temperature partition extraction and ultra‐high‐performance liquid chromatography with tandem mass spectrometry, without the use of a labeled analyte, was developed and validated to determine and quantify urinary S‐phenylmercapturic acid in urine samples. The World Health Organization, in its guidelines for air quality in Europe, recognizes that benzene is carcinogenic to humans and there is no safe level of exposure. Urinary S‐phenylmercapturic acid is a sensitive and specific biological marker of exposure to benzene. The new analytical method, extraction, and analysis, were linear in the working range between 0.1 and 200.0 μg/L, precise (relative standard deviation lower than 6.0%), accurate (97.0–105.0%), and sensitive. The method's limits of detection and quantification were 0.02 and 0.084 μg/L, respectively. The recovery with the low‐temperature partition extraction was 96.1%, with relative standard deviation less than 3.8%. The method is simple, accurate, and reproducible, and has been successfully applied in the evaluation of nonoccupational exposure to benzene, by urinary S‐phenylmercapturic acid in urine samples.     

Evaluation of matrix solid‐phase dispersion extraction for 11 β‐agonists in swine feed by liquid chromatography with electrospray ionization tandem mass spectrometry

A sensitive liquid chromatography with tandem mass spectrometry method was developed for the determination of 11 β‐agonists (clenbuterol, salbutamol, ractopamine, terbutaline, fenoterol, cimaterol, isoxsuprine, mabuterol, mapenterol, clenproperol, and tulobuterol) in swine feed. This rapid, simple, and effective extraction method was based on matrix solid‐phase dispersion. The limit of quantification of clenbuterol, cimaterol, mabuterol, salbutamol, terbutaline, mapenterol, clenproperol, and tulobuterol was 1 μg/kg and that of ractopamine, fenoterol, and isoxsuprine was 2 μg/kg. The recoveries of β‐agonists spiked in swine feeds at a concentration range of 1–8 μg/kg were >83.1% with relative standard deviations <9.3%. This rapid and reliable method can be used to efficiently separate, characterize, and quantify the residues of 11 β‐agonists in swine feeds with advantages of simple pretreatment and environmental friendliness.     

Analysis of nitrogenous organic compounds from mainstream cigarette smoke using low‐temperature solvent extraction followed by comprehensive two‐dimensional gas chromatography with high‐resolution time‐of‐flight mass spectrometry

A method involving comprehensive two‐dimensional gas chromatography coupled to high‐resolution time‐of‐flight mass spectrometry was developed and applied to the analysis of nitrogenous organic compounds present in mainstream cigarette smoke trapped on self‐designed equipment. The samples were prepared using low‐temperature solvent extraction under liquid nitrogen and analyzed by comprehensive two‐dimensional gas chromatography with high‐resolution time‐of‐flight mass spectrometry. Important experimental parameters, such as the type and volume of the extraction solvent and flow rate of smoking, were optimized to improve the analysis parameter. The results indicated that 180 mL of diethyl ether in the low‐temperature solvent extraction apparatus system with a 4 mL/min smoke flow rate were the optimal conditions. Then, 85 nitrogenous organic compounds were identified and quantified using a mass spectral library search, accurate mass ion and N‐rules of a molecular formula for nitrogen compounds. Finally, a comparison of the low temperature solvent extraction method and Cambridge filter pad method indicated that more peaks, a higher peak volume and better repeatability were obtained using the low‐temperature solvent extraction method.     

Gas‐phase interactions of organotin compounds with glycine

Gas‐phase interactions of organotins with glycine have been studied by combining mass spectrometry experiments and quantum calculations. Positive‐ion electrospray spectra show that the interaction of di‐ and tri‐organotins with glycine results in the formation of [(R)₂Sn(Gly)‐H]⁺and [(R)₃Sn(Gly)]⁺ ions, respectively. Di‐organotin complexes appear much more reactive than those involving tri‐organotins. (MS/MS) spectra of the [(R)₃Sn(Gly)]⁺ ions are indeed simple and only show elimination of intact glycine, generating the [(R)₃Sn]⁺ carbocation. On the other hand, MS/MS spectra of [(R)₂Sn(Gly)‐H]⁺complexes are characterized by numerous fragmentation processes. Six of them, associated with elimination of H₂O, CO, H₂O + CO and formation of [(R)₂SnOH]⁺ (?57 u),[(R)₂SnNH₂]⁺( ?58 u) and [(R)₂SnH]⁺ (?73 u), are systematically observed. Use of labeled glycines notably concludes that the hydrogen atoms eliminated in water and H₂O + CO are labile hydrogens. A similar conclusion can be made for hydrogens of [(R₂)SnOH]⁺and [(R₂)SnNH₂]⁺ions. Interestingly, formation [(R)₂SnH]⁺ ions is characterized by a migration of one the α hydrogen of glycine onto the metallic center. Finally, several dissociation routes are observed and are characteristic of a given organic substituent. Calculations indicated that the interaction between organotins and glycine is mostly electrostatic. For [(R)₂Sn(Gly)‐H]⁺complexes, a preferable bidentate interaction of the type η²‐O,NH2 is observed, similar to that encountered for other metal ions. [(R)₃Sn]⁺ ions strongly stabilize the zwitterionic form of glycine, which is practically degenerate with respect to neutral glycine. In addition, the interconversion between both forms is almost barrierless. Suitable mechanisms are proposed in order to account for the most relevant fragmentation processes. Copyright © 2013 John Wiley & Sons, Ltd.     

Gas‐phase interactions of organotin compounds with cysteine

The gas‐phase interactions of cysteine with di‐organotin and tri‐organotin compounds have been studied by mass spectrometry experiments and quantum calculations. Positive‐ion electrospray spectra show that the interaction of di‐ and tri‐organotins with cysteine results in the formation of [(R)₂Sn(Cys‐H)]⁺ and [(R)₃Sn(Cys)]⁺ ions, respectively. MS/MS spectra of [(R)₂Sn(Cys‐H)]⁺ complexes are characterized by numerous fragmentation processes, notably associated with elimination of NH₃ and (C,H₂,O₂). Several dissociation routes are characteristic of each given organic species. Upon collision, both the [(R)₃Sn(Gly)]⁺ and [(R)₃Sn(Cys)]⁺ complexes are associated with elimination of the intact amino acid, leading to the formation of [(R)₃Sn]⁺ cation. But for the latter complex, two additional fragmentation processes are observed, associated with the elimination of NH₃ and C₃H₄O₂S. Calculations indicate that the interaction between organotins and cysteine is predominantly electrostatic but also exhibits a considerable covalent character, which is slightly more pronounced in tri‐organotin complexes. A preferred bidentate interaction of the type ‐η²‐S‐NH₂, with sulfur and the amino group, is observed. As for the [(R)₃Sn(Cys)]⁺ complexes, their stability is due to the combination of the hydrogen bond taking place between the amino group and the sulfur lone pair and the interaction between the carboxylic oxygen atom and the metal. Copyright © 2016 John Wiley & Sons, Ltd.     

Multiresidue analysis of glucocorticoids in milk by LC–MS/MS with low‐temperature purification and dispersive solid‐phase extraction

A multiresidue method for the determination of 12 glucocorticoids (clobetasol propionate, budesonide, triamcinolone, triamcinolone acetonide, fludrocortisone acetate, flumethasone, beclomethasone, prednisone acetate, 6‐α‐methylprednisolone, hydrocortisone, cortisone, and prednisone) in bovine milk was developed using liquid chromatography with tandem mass spectrometry. Isoflupredone was used as an internal standard. Milk samples were treated with ethyl acetate to extract glucocorticoids and were frozen at −20°C for 6 h to precipitate fat. The extract was dried under nitrogen, and residues were dissolved in an acetonitrile/water solution. A further clean‐up step was used by dispersive solid‐phase extraction, with octadecyl silica and primary secondary amine as the absorbents. The recoveries of glucocorticoids spiked at 0.5, 1.0, 10.0 μg/kg ranged from 75.7 to 117.3%, except for clobetasol propionate and budesonide (16.1–49.5%). The limits of quantification were 0.01–0.5 μg/kg in milk. This method has been successfully applied in real samples. The results demonstrated that this method is simple, robust, and suitable for identification of glucocorticoid residues in milk.     

Multi‐residue analysis of 44 pharmaceutical compounds in environmental water samples by solid‐phase extraction coupled to liquid chromatography‐tandem mass spectrometry

A solid‐phase extraction combined with a liquid chromatography‐tandem mass spectrometry analysis has been developed and validated for the simultaneous determination of 44 pharmaceuticals belonging to different therapeutic classes (i.e., antibiotics, anti‐inflammatories, cardiovascular agents, hormones, neuroleptics, and anxiolytics) in water samples. The sample preparation was optimized by studying target compounds retrieval after the following processes: i) water filtration, ii) solid phase extraction using Waters Oasis HLB cartridges at various pH, and iii) several evaporation techniques. The method was then validated by the analysis of spiked estuarine waters and wastewaters before and after treatment. Analytical performances were evaluated in terms of linearity, accuracy, precision, detection, and quantification limits. Recoveries of the pharmaceuticals were acceptable, instrumental detection limits varied between 0.001 and 25 pg injected and method quantification limits ranged from 0.01 to 30.3 ng/L. The precision of the method, calculated as relative standard deviation, ranged from 0.3 to 49.4%. This procedure has been successfully applied to the determination of the target analytes in estuarine waters and wastewaters. Eight of these 44 pharmaceuticals were detected in estuarine water, while 26 of them were detected in wastewater effluent. As expected, the highest values of occurrence and concentration were found in wastewater influent.     

Magnetic octadecyl‐based matrix solid‐phase dispersion coupled with gas chromatography with mass spectrometry in a proof‐of‐concept determination of multi‐class pesticide residues in carrots

A novel procedure is put forward based on the combination of the well‐established matrix solid‐phase dispersion and the magnetic and sorption properties of magnetic octadecyl in the presence of n‐octanol and was employed in a proof‐of‐concept sample preparation and determination of several classes of pesticide residues in carrots. The procedure does not require the transfer of blend to cartridge and subsequent packing, nor any co‐sorbent for extract clean up. The hydrophobic magnetic nanoparticles utilized as a sorbent, can be retrieved by n‐octanol under the application of a magnetic field due to hydrophobic interactions. Elution of pesticide residues is then carried out with an organic solvent. A total of 26 pesticides were included in this procedure and the target compounds were analyzed using gas chromatography with mass spectrometry in the selective ion monitoring mode. The average extraction recoveries obtained from carrot samples fortified at three different concentrations (20, 50, and 500 μg/kg) were 77–107%. The estimated limits of quantitation for most target analytes were in the low μg/kg level. The study demonstrates that the proposed extraction procedure is simple and effective, avoiding a clean‐up step for the sample preparation of vegetable.     

Determination of ultraviolet filter compounds in environmental water samples using membrane‐protected micro‐solid‐phase extraction

A method based on membrane‐protected micro‐solid‐phase extraction coupled with gas chromatography and mass spectrometry was developed for the determination of six ultraviolet filter compounds in various aqueous media. Multiwalled carbon nanotubes as the sorbent were encapsulated in a sealed polypropylene membrane packet and immersed in the sample to extract the analytes, and then dichloromethane was used for desorption purpose. The method was sensitive enough for quantitative analysis of the target analytes, with limits of quantification between 0.01 and 0.06 μg/L, and produced a linear response (R² > 0.991) over the calibration range (0.05–6 μg/L). The obtained reproducibility was practically suitable with relative standard deviation values of less than 14% in pure water (spiked at 0.20/μg L) and less than 15% in real samples. The optimized method was applied for the analysis of real water samples with varying matrix complexity: tap, river, and dam water; geothermal spa; and sewage treatment plant effluent. Various levels and patterns of contamination were observed in the examined samples, while the sample from spa was the most contaminated, regarding the target analytes. Matrix spikes and matrix spike replicates were also analyzed to validate the technique for analysis of real aqueous samples, and satisfactory results were achieved.     

Fast and selective extraction of chloramphenicol from soil by matrix solid‐phase dispersion using molecularly imprinted polymer as dispersant

The molecularly imprinted polymer (MIP) was synthesized and used as dispersant of matrix solid‐phase dispersion (MSPD) for the extraction of chloramphenicol (CAP) in soil samples. The satisfactory recovery of CAP was obtained by the optimized extraction conditions: 1:2 as the ratio of sample to MIPs; 5 min as the dispersion time; 30% aqueous methanol as washing solvent and methanol as elution solvent. The CAP extracted from soil was determined by LC‐MS/MS. The slight ion suppression phenomenon was observed for the CAP when the sample was cleaned up by MSPD with MIP as dispersant, when compared with C18 as MSPD dispersant, which caused significant ion suppression. LOD of CAP is 4.1 ng/g. RSDs of intra‐ and inter‐day tests ranging from 3.1 to 6.2% and from 3.9 to 8.3% are obtained. At all three fortified levels (20, 100 and 500 ng/g), recoveries of CAP are in the range of 86.9–92.6%. The effect of ageing time of spiked soil sample on the CAP recovery was examined. The CAP recovery decreased from 91.0 to 36.9% when the ageing time changed from 1 day to 4 wk.     

Applications of solid‐phase micro‐extraction with mass spectrometry in pesticide analysis

Pesticides, widely applied in agriculture, can produce a variety of transformation products and their continuous use causes deleterious effects to ecosystem. Efficient and sensitive analytical techniques for enrichment and analysis of pesticides samples are highly required. Compared with other extraction methods, solid‐phase micro extraction is a solvent free, cost effective, robust, versatile, and high throughput sample preparation technique, especially for the analysis of pesticides from complicated matrices. Coupling of solid‐phase micro extraction with gas chromatography and mass spectrometry and liquid chromatography–mass spectrometry has been extensively applied in pesticide analysis. On the other hand, in recent years, combination of fast separation using solid‐phase micro extraction and rapid detection using ambient mass spectrometry is providing highly efficient pesticide screening. This article summarizes the applications of solid‐phase micro extraction coupled to mass spectrometry for pesticides analysis.     

Multiwalled‐carbon‐nanotubes‐based matrix solid‐phase dispersion extraction coupled with high‐performance liquid chromatography for the determination of honokiol and magnolol in Magnoliae Cortex

In this paper, multiwalled‐carbon‐nanotube‐based matrix solid‐phase dispersion coupled to HPLC with diode array detection was used to extract and determine honokiol and magnolol from Magnoliae Cortex. The extraction efficiency of the multiwalled‐carbon‐nanotube‐based matrix solid‐phase dispersion was studied and optimized as a function of the amount of dispersing sorbent, volume of elution solvent, and flow rate of elution solvent, with the aid of response surface methodology. An amount of 0.06 g of carboxyl‐modified multiwalled carbon nanotubes and 1.5 mL of methanol at a flow rate of 1.1 mL/min were selected. The method obtained good linearity (r² > 0.9992) and precision (RSD < 4.7%) for honokiol and magnolol, with limits of detection of 0.045 and 0.087 μg/mL, respectively. The recoveries obtained from analyzing in triplicate spiked samples were determined to be from 90.23 to 101.10% and the RSDs from 3.5 to 4.8%. The proposed method that required less samples and reagents was simpler and faster than Soxhlet and maceration extraction methods. The optimized method was applied for analyzing five real samples collected from different cultivated areas.     

Simultaneous determination of seven compounds in Chinese patent medicines Chenxiangqu by matrix solid‐phase dispersion coupled with ultra high performance liquid chromatography and quadrupole time‐of‐flight mass spectrometry

A simple, efficient, and sensitive strategy by coupling matrix solid‐phase dispersion with ultra high performance liquid chromatography quadrupole time‐of‐flight mass spectrometry was proposed to extract and determine three types of components (including seven analytes) in Chinese patent medicines Chenxiangqu. The highly ordered mesoporous material Fe‐SBA‐15 synthesized under weakly acidic conditions was selected as a dispersant in matrix solid phase dispersion extraction for the first time. Several parameters including the mass ratio of sample to dispersant, the type of dispersant, the grinding time, and the elution condition were investigated in this work. Under the optimized conditions, 20 compounds were identified by quadrupole time‐of‐flight mass spectrometry and seven analytes were quantified. The results demonstrated that the developed method has good linearity (r > 0.9995), and the limits of detection of the analytes were as low as 0.55 ng/mL. The recoveries of all seven analytes ranged from 97.6 to 104.6% (relative standard deviation < 3.4%). Finally, the improved method was successfully applied to determination of five batches of Chenxiangqu samples, which provided a robust method in quality control of Chinese patent medicines Chenxiangqu. The developed strategy also shows its great potential in analysis of complex matrix samples.     

Simultaneous determination of phenolic compounds in Equisetum palustre L. by ultra high performance liquid chromatography with tandem mass spectrometry combined with matrix solid‐phase dispersion extraction

A method based on matrix solid‐phase dispersion extraction followed by ultra high performance liquid chromatography with tandem mass spectrometry is presented for the extraction and determination of phenolic compounds in Equisetum palustre. This method combines the high efficiency of matrix solid‐phase dispersion extraction and the rapidity, sensitivity, and accuracy of ultra high performance liquid chromatography with tandem mass spectrometry. The influential parameters of the matrix solid‐phase dispersion extraction were investigated and optimized. The optimized conditions were as follows: silica gel was selected as dispersing sorbent, the ratio of silica gel to sample was selected to be 2:1 (400/200 mg), and 8 mL of 80% methanol was used as elution solvent. Furthermore, a fast and sensitive ultra high performance liquid chromatography with tandem mass spectrometry method was developed for the determination of nine phenolic compounds in E. palustre. This method was carried out within <6 min, and exhibited satisfactory linearity, precision, and recovery. Compared with ultrasound‐assisted extraction, the proposed matrix solid‐phase dispersion procedure possessed higher extraction efficiency, and was more convenient and time saving with reduced requirements on sample and solvent amounts. All these results suggest that the developed method represents an excellent alternative for the extraction and determination of active components in plant matrices.     

Screening for pesticide residues in oil seeds using solid-phase dispersion extraction and comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry

In this paper, we describe the development of an oil-absorbing matrix solid-phase dispersion extraction with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry suitable for screening of 68 pesticide residues (PRs) in peanut, soybean, rape seed, sesame, and sunflower seed. The 68 PRs include 27 kinds of organophosphorus, 23 organic chlorines, 11 synthetic pyrethroids, and 7 carbamates. Heptachlor epoxide was used as the internal standard. Aminopropyl silica was chosen as the dispersion sorbent of the oil-absorbing matrix solid-phase dispersion extraction and was applied to capture hydrophobic components from high oil samples. A 35-min orthogonal separation was performed by using comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry with a nonpolar-polar column set. Identification of 68 PRs in the extract was finished by using the time-of-flight mass spectrometry in the assistance of an automated peak-find and spectral deconvolution software. A screening based on control design was introduced and explained. This screening method considerably reduced the cost for the quantitative and confirmatory analyses. The quality of present screening method was evaluated by the Document No. SANCO/10684/2009. The false positive rate and false negative rate provide a useful tool for the evaluation of screening performance.     

Rapid and sensitive determination of major polyphenolic components in Euphoria longana Lam. seeds using matrix solid‐phase dispersion extraction and UHPLC with hybrid linear ion trap triple quadrupole mass spectrometry

A rapid and sensitive method for the extraction and determination of four major polyphenolic components in Euphoria longana Lam. seeds is presented for the first time based on matrix solid‐phase dispersion extraction followed by ultra high performance liquid chromatography with hybrid triple quadrupole linear ion trap mass spectrometry. Matrix solid‐phase dispersion method was designed for the extraction of Euphoria longana seed constituents and compared with microwave‐assisted extraction and ultrasonic‐assisted extraction methods. An Ultra high performance liquid chromatography with hybrid triple quadrupole linear ion‐trap mass spectrometry method was developed for quantitative analysis in multiple‐reaction monitoring mode in negative electrospray ionization. The chromatographic separation was accomplished using an ACQUITY UPLC BEH C₁₈ (2.1 mm × 50 mm, 1.7 μm) column with gradient elution of 0.1% aqueous formic acid and 0.1% formic acid in acetonitrile. The developed method was validated with acceptable linearity (r² > 0.999), precision (RSD ≤ 2.22%) and recovery (RSD ≤ 2.35%). The results indicated that matrix solid‐phase dispersion produced comparable extraction efficiency compared with other methods nevertheless was more convenient and time‐saving with reduced requirements on sample and solvent volumes. The proposed method is rapid and sensitive in providing a promising alternative for extraction and comprehensive determination of active components for quality control of Euphoria longana products.     

Speciation Analysis of Thallium by Reversed‐phase Liquid Chromatography ‐ Inductively Coupled Plasma Mass Spectrometry

An inductively coupled plasma mass spectrometer (ICP‐MS) was used as a liquid chromatographic detector for the speciation analysis of thallium in environmental samples. In this study, ionic thallium species, namely Tl(I) and Tl(III) were well separated by reversed‐phase high performance liquid chromatography (RP‐HPLC) with a C8‐HPLC column as the stationary phase and 1 mmol L^?1 tetrabutylammonium phosphate (TBAP), 2 mmol L^?1 diethylenetriamine pentaacetic acid (DTPA) in 1% v/v methanol solution (pH 6) as the mobile phase. Effluent from the HPLC column was delivered to the nebulizer of the ICP‐MS for the determination of thallium. The separation was complete in less than 3 min. Detection limit was 0.002 μg L^?1 for both Tl(I) and Tl(III) compounds based on peak height. The relative standard deviation of the peak areas for five injections of a mixture containing 1 μg Tl L^?1 was better than 3.4%. The concentrations of Tl compounds were determined in standard reference materials, including NIST SRM 1643e Trace Elements in Water and NRCC NASS‐5 Open Ocean Seawater and water samples collected in Kaohsiung area, Taiwan. The HPLC‐ICP‐MS results of the reference samples agreed with the reference values. This method has also been applied to determine Tl(I) and Tl(III) compounds in custard apple (Annona squamosa) leaves collected from Chai‐shan Mountain, Kaohsiung and Taitung City, Taiwan. The thallium species were quantitatively leached from the leaves with a 5 mmol L^?1 DTPA in 100 mmol L^?1 ammonium acetate solution in an ultrasonic bath during a period of 30 min. The HPLC‐ICP‐MS result that was obtained after the analysis of leaves sample showed a satisfactory agreement with the total thallium concentration obtained by ICP‐MS analysis of completely dissolved sample.     

Simultaneous determination of nucleosides and their bases in Cordyceps sinensis and its substitutes by matrix solid‐phase dispersion extraction and HPLC

Nine nucleosides and nucleobases, including uracil, adenine, thymine, uridine, adenosine, thymidine, cytidine, guanosine, and cordycepin in natural Cordyceps sinensis, cultured Cordyceps mycelia, and Cordyceps fruiting bodies were extracted by matrix solid‐phase dispersion (MSPD) and determined by HPLC. The experimental conditions for the MSPD extraction were optimized. Florisil was used as dispersant, petroleum ether as washing solvent, and methanol as elution solvent. The Florisil‐to‐sample ratio was selected to be 4:1 and no additional clean‐up sorbent was needed. The calibration curves had good linear relationships (r > 0.9997). The LOD and LOQ were in the range of 12 ～ 79 and 41 ～ 265 ng/mL, respectively. The intra‐ and interday precision were lower than 8.3%. The recoveries were between 61.5 and 93.2%. The present method consumed less sample compared with ultrasonic extraction and heating reflux extraction (HRE). The extraction yields obtained by using the present method are much higher than those obtained by UE and comparable to those obtained by HRE.     

Screening of drugs of abuse and toxic compounds in human whole blood using online solid‐phase extraction and high‐performance liquid chromatography with time‐of‐flight mass spectrometry

A novel method for the screening of 151 drugs of abuse and toxic compounds in human whole blood has been developed and validated by online solid‐phase extraction with liquid chromatography coupled to time‐of‐flight mass spectrometry. Analytes were extracted and separated by using a fully automated online solid‐phase extraction liquid chromatography system with total chromatographic run time of 26 min. Time‐of‐flight mass spectrometry screening of 151 drugs of abuse and toxic compounds was performed in a full‐scan (m/z 50–800) mode using an MS^E acquisition of molecular ions and fragment ions data at two collision energies (one was 6 eV and another one was in the range of 5–45 eV). The compounds were identified based on retention times and exact mass of molecular ions and fragment ions. The limit of detection ranged from 1 to 100 ng/mL and the recovery of the method ranged from 6.3 to 163.5%. This method is proved to be a valuable screening method allowing fast and specific identification of drugs in human whole blood.