回料流入口高度对循环流化床提升管流动特性的影响

The axial pressure drop profile and the radial solids distribution were measured in a circulating fluidized bed for evaluating the effects of return gas-solids stream position on the riser flow properties.The saturation carrying capacity of gas for Geldart B typed particles and the flow mode of return gas-solids stream in the bed were discussed.It was found that arranging the inlet at a higher position of the riser would make the bottom bed leaner when U₀ was high and G_s was low.When G_s increased,the longer influenced region of return particles and a small air-staging through lifting the loosening air injection position made the bottom bed become denser significantly.The deceleration and residence of return particles caused a relatively denser but asymmetrical region in the vicinity of inlet.But much more symmetrical solids distribution profile was found in the upper and lower regions far away from the inlet.The effects of inlet height on the flow properties of the riser with air-staging also were analyzed.The secondary air injection below the solids inlet could not cut off the solids exchange in the bed.The bed solids concentration increased when the particles inlet moved to a higher position of the bed when air-staging was adopted.Using CO₂ as tracer,the dispersion of the loop-seal-fluidizing air for transmitting the return particles was investigated.It was found that the loop-seal fluidizing air dispersion rate was low but can be enhanced by the secondary air injection.     

THE PARTICLE VELOCITY DISTRIBUTION IN A RISER OF DILUTE CIRCULATING FLUIDIZED BED

This paper presents an experimental study on the radial and axial profiles of local particle velocity of flu-idized catalyst(FCC)particles in a circulating fluidized bed of 8000mm in height and 186mm in inside diameterwith a Fiber-Optic Probe Laser Doppler Velocimetry.It has been found that the radial profiles of local particlevelocity are parabolic,even in the centre region and steep in the region near the bed wall,and that the length ofparticle acceleration along the bed height is longer than expected.The following formula has been recommended to correlate the 1 ocal particle velocity with dilute gas-solidflow in the bed:where a,b,c and e are functions of radial positions.     

气固循环流化床提升管环核区颗粒质量传递系数的估计

Based on analysis of energy dissipation in the core region of gas-solid fluidized bed risers,a simplified model for determination of core-annulus solids mass transfer coefficient was developed according to turbulent diffu- sion mechanism of particles.The simulation results are consistent with published experimental data.Core-annulus solids mass transfer coefficient decreases with increasing particle size,particle density and solids circulation rate, but generally increases with increasing superficial gas velocity and riser diameter.In the upper dilute region of gas-solid fiuidized bed risers,core-annulus solids mass transfer coefficient was found to change little with the axial coordinate in the bed.     

Hydrodynamics of three-phase fluidization of homogeneous ternary mixture in a conical conduit——Experimental and statistical analysis

Hydrodynamics of conical fluidized bed differ from that of columnar beds by the fact that a velocity gradient exists along the axial direction of the bed.The gas–liquid–solid fluidized bed has emerged in recent years as one of the most promising devices for three-phase operations.Such a device is of considerable industrial importance as evident from its wide applications in chemical,refining,petrochemical,biochemical processing,pharmaceutical and food industries.To explore this,a series of experiments have been carried out for homogeneous well-mixed ternary mixtures of dolomite of varying compositions in a three-phase conical fluidized bed.The hydrodynamic characteristics determined included the bed pressure drop,bed fluctuation and bed expansion ratios.The single and combined effects of operating parameters such as superficial gas velocity,superficial liquid velocity,initial static bed height,average particle size and cone angle on the responses have been analyzed using response surface methodology(RSM).A 25 full factorial central composite experimental design has been employed.Analysis of variance(ANOVA) showed a high coefficient of determination value and satisfactory prediction second-order regression models have been derived.Experimental values of bed pressure drop,bed fluctuation and bed expansion ratios have been found to agree well with the developed correlations.     

循环硫化床上升管中动态行为的拟流体模拟

The kinetic theory of granular flow (KTGF) is modified to fit the Einstein′s equation for effective viscosity of dilute flow. A pseudo-fluid approach based on this modified KTGF is used to simulate the dynamic formation and dissipation of clusters in a circulating fluidized bed riser. The agglomeration of particles reduces slip velocity within particle clusters, and hence results in two reverse trends: discrete particles are lifted by air while particle clusters fall down along the wall. The dynamic equilibrium of these two types of motion leads to the characteristic sigmoid profile of solid concentration along the longitudinal direction. The predicted solid velocity, lateral and longitudinal profiles of solid volume fraction and annulus thickness are in reasonable agreement with experimental results.     

循环流化床密相区内颗粒的横向扩散的研究

Lateral solid mixing was investigated experimentally in the dense zone of a 900mm×100mm×5.2m rectangular circulating fluidized bed riser. Using heated tracer injection, the lateral solid dispersion was determined by measuring the temperature response at different lateral positions. Furthermore, a one-dimensional dispersion model, which describes the solid mixing in the dense zone, is presented. The experimental results were used to determine the lateral particle dispersion coefficient under various operating conditions. A correlation of dispersion coefficient with bed height, gas velocity, and particle size is also proposed.     

气固流化床混沌动力结构突变分析

A new method called structural catastrophe analysis was applied to the analysis of pressure fluctuation time series with chaotic and fractal characteristics in gas-solids fluidized bed.In every type of fixed bed,bubbling bed,turbulent bed,fast fluidized bed and pneumatic conveying stage,pressure fluctuation signals were sampled and dynamic exponents were solved.The changes of T_mean and T_max in different types of fluidized bed were analyzed and summarized.It was concluded that T_mean and T_max can indicate different types of fluidized,and T_max can also be recognized as a new characteristic parameter in addition to correlation parameters,LE exponent and K entropy.     

CFD simulation of solids residence time distribution in a multi-compartment fluidized bed

The present work focuses on a numerical investigation of the solids residence time distribution(RTD)and the fluidized structure of a multi-compartment fluidized bed,in which the flow pattern is proved to be close to plug flow by using computational fluid dynamics(CFD)simulations.With the fluidizing gas velocity or the bed outlet height rising,the solids flow out of bed more quickly with a wider spread of residence time and a larger RTD variance(σ2).It is just the heterogeneous fluidized structure that being more prominent with the bed height increasing induces the widely non-uniform RTD.The division of the individual internal circulation into double ones improves the flow pattern to be close to plug flow.     

二维双支腿流化床内气体混合特性

Experiments of gas mixing between two half-beds were performed in a dual-leg circulating fluidized bed(DL-CFB)240 mm in width,40 mm in depth and 2000 mm in height by using glass beads with diameter of 0.25-0.28 mm as bed material.SO₂ and CO as the gas tracers entering the left and right distributors separately were used to simulate the gas mixing between the two legs.MSD(mean square displacement)model was adopted to calculate the gas dispersion coefficient(D_w)which was used to investigate the effect of fluidization velocity and bed material inventory on gas mixing in the DL-CFB.The experimental results showed that D_w was about 50-300 cm²穝^-1 at different fluidization velocities and bed material inventories.A higher fluidization velocity benefited particles exchange between two half-beds,which intensified the gas-solids interactions at the region with higher solids volume fraction.The gas mixing in the lower region of the DL-CFB was stronger than that in the upper region of the bed.A higher bed inventory was helpful to gas mixing at a lower fluidization velocity,while a higher fluidization velocity weakened gas mixing because of higher solids concentration in the center of the bed that prevented gas mixing.     

Heat Transfer in a Liquid-Solid Circulating Fluidized Bed Reactor with Low Surface Tension Media

Heat transfer characteristics between the immersed heater and the bed content were studied in the riser of a liquid-solid circulating fluidized bed, whose diameter and height were 0.102 m (ID) and 2.5 ...     

提升管-流化床耦合反应器颗粒约束返混区的流动特性及约束作用分析

针对催化汽油辅助反应器改质降烯烃工艺,在一套提升管-流化床耦合反应器大型冷态实验装置上,系统研究了提升管出口段的颗粒流动特性,通过定义约束指数R_i（R_i为颗粒约束返混区实际截面平均固含率与理论截面平均固含率之比）定量反映提升管出口分布器及流化床层的约束作用。结果表明,与常规提升管相比,耦合反应器提升管出口存在一个颗粒约束返混区,其长度主要受表观气速、颗粒循环强度及上部流化床内颗粒静床高度影响;由于出口设置了倒锥形分布器,使得颗粒约束返混区靠近提升管出口区域在表观气速较低和颗粒循环强度较大时,局部固含率最大值出现在量纲 1半径Φ＝0.7处;颗粒约束返混区的约束指数在靠近出口的过程中逐渐增大,气固流动受到分布器及上部流化床层的约束作用亦逐渐增强。     

组合约束型提升管出口气固分布器的压降

在一套组合约束型提升管冷态实验装置上,通过实验研究了不同操作条件下提升管出口气固分布器的压降,并与常规气体分布器压降进行了对比。实验结果表明,在零床层及有床层的操作模式下,气固分布器压降均随提升管内表观气速和颗粒循环强度的增加而增大,在颗粒循环强度较低时,气固分布器压降曲线变化的斜率随着表观气速的增加而增大,在颗粒循环强度较高时,气固分布器压降曲线变化的斜率随着表观气速的增加而减小;随着开孔率及上部流化床层压降增加,气固分布器压降呈降低趋势,当流化床层压降达到一定程度后,分布器各孔方可实现有效布气,此后气固分布器压降趋于近似不变;在相同表观气速及开孔率下,气固分布器压降大于常规气体分布器压降。     

提升管与气-固环流床层耦合反应器的流体力学特性及流动模型

针对催化汽油辅助反应器改质降烯烃技术,在一套提升管与气-固环流床层耦合反应器大型冷模实验装置上,研究了上部环流床层的流体力学特性。结果表明,在环流床层与提升管耦合操作的情况下,床层内颗粒环流存在两种推动力,分别为静压差推动力和颗粒喷射推动力;环隙与导流筒之间的整体平均固含率差随导流筒表观气速增加而增加,随颗粒外循环强度增加而降低;颗粒环流速度随导流筒表观气速和颗粒外循环强度增加而增加。通过对环流床层进行动量衡算,建立了提升管与环流床层耦合流动的数学模型,模型平均相对误差在15.95％以内。     

60米高矩形截面循环流化床内物料分布冷态试验

为研究超高提升管内的气固流动特性,依托四川白马电厂600MW超临界循环流化床锅炉现有钢架,将原有60m高的提升管冷模试验台的上部20m改为矩形截面的循环流化床提升管试验台。本文重点研究了提升管流化风速对上部颗粒浓度的轴向/截面分布特性及其影响因素。试验结果表明：颗粒浓度和颗粒粒径的分布特性与流化风速和几何结构密切相关,在一定初始床料高度下,随着风速的增加,提升管上部的空隙率沿轴向先不变然后减少,并最终呈现倒C形分布;截面浓度从均匀分布逐渐变为近短边壁处的颗粒浓度要明显大于近长边壁处的不均匀分布;平均颗粒粒径则随风速的增加而增大,沿截面分布均匀,但是沿提升管高度方向平均颗粒粒径沿轴向会略微减小,且提升管上部近短边壁的颗粒粒径要稍小于近长边壁的。     

多段分级转化流化床提升管速度场的研究

针对流化床煤气化过程中需要长气固接触时间和高固体浓度,开发了耦合灰熔聚流化床和提升管的多段分级转化流化床。为了研究多段分级转化流化床提升管中局部颗粒速度的径向、轴向分布,在不同的操作条件下,采用PV-6型颗粒速度测量仪在冷态实验装置中系统测定提升管内局部颗粒速度。实验结果表明:提升管中任何径向、轴向位置的颗粒速度随着操作气速的增大而增大,随循环量的增加而减小。操作条件对中心区颗粒速度变化的影响明显高于边壁区。颗粒的加速首先发生在提升管中心区域,然后向边壁区域扩展。颗粒速度径向分布的不均匀性沿轴向逐渐增大,并且受操作气速影响比较大。     

耦合流化床提升管内固含率径向分布及沿轴向的发展

针对催化汽油辅助反应器改质降烯烃工艺,结合提升管与流化床的特点,建立了一套提升管与流化床耦合反应器大型冷态实验装置. 在不同操作条件下,采用PV-4A型光纤密度仪测定了提升管内固含率沿径向的分布规律. 结果表明,固含率径向分布整体上呈现中心小、边壁大的环-核结构分布特征;沿轴向向上,各径向位置上的固含率在颗粒加速区逐渐降低,在充分发展区趋于稳定,在颗粒约束返混区又有所升高;各径向位置上的固含率随表观气速增大或颗粒循环强度减小而减小,且均匀性变好;提升管上部流化床内颗粒静床高度只对颗粒约束返混区内固含率径向分布有影响,而对颗粒加速区和充分发展区的固含率径向分布影响较小;当表观气速较低或颗粒循环强度较大时,颗粒约束返混区上部局部固含率最大值出现在无因次半径f=r/R=0.7附近,此时局部无因次固含率es*=es/ 沿轴向在H>5.33 m时不再具有相似性;通过比较径向不均匀指数,得到轴向各区固含率径向分布趋于均匀的程度依次为：充分发展区>颗粒约束返混区>颗粒加速区. 利用实验数据回归出了局部固含率径向分布关联式,其平均相对误差在6%以内.     

提升管加床层反应器不同操作模式下的压力脉动特性

在提升管加床层反应器冷模实验装置上,分别采取零床层和有床层的操作模式,测量并分析了提升管内的压力脉动行为. 结果表明,有床层操作模式下的提升管内压力脉动标准偏差明显高于零床层操作模式;压力脉动主频零床层操作模式下主要集中于1.56?3.13和0?0.391 Hz,主要源于提升管内颗粒的脉动,有床层操作模式下为12.5?25.0和0?0.391 Hz,12.5?25.0 Hz频段主要源于提升管出口上方设置的气固分布器加流化床层对提升管内气固流动的约束及其影响下的气体脉动行为,0?0.391 Hz频段主要源于提升管段进料的不连续性及其与进料口下方提升气体的相互作用.     

The influence of distributor structure on the solids distribution and flow development in circulating fluidized beds

The influence of distributor structure on solids distribution is studied in two riser circulating fluidized bed reactors with different distributor structures but similar diameters. Optic fibre probes were used for the measurement of local solids distribution. The axial and radial distribution of solids holdup in the riser with a multi‐tube distributor is more uniform than that with a multi‐orifice distributor. The radial profiles of particle velocity in the riser with the multi‐tube distributor are also more uniform than that with the multi‐orifice distributor. In the riser with the multi‐tube distributor, both gas and particles are distributed more uniformly across the section, so that the flow acceleration is much more uniform and faster. The flow development is much faster and the fully developed region is reached early for the riser with the multi‐tube distributor. The distributor design is an important factor for the design of circulating fluidized bed reactor.     

高密度液固循环流化床流动特性研究及数值模拟

在φ80 mm×8000 mm的液固循环流化床提升管中,利用实心玻璃珠和常温水,采用实验和数值模拟相结合的方法对高密度液固循环流化床的流动特性进行了考察。实验发现,高密度液固提升管中,颗粒固含率和颗粒速度径向分布均为抛物线分布,轴向平均固含率分布总体上为下浓上稀的波动形式分布,颗粒在提升管中的流动表现出加速-减速-再加速直至充分发展的过程。这种分布特征与较高颗粒浓度、较高表观液速和颗粒循环速率及喷管式液体分布器的影响有关。液固提升管中固体颗粒的停留时间分布曲线均为尖而窄、较对称且没有明显拖尾的单峰分布,这表明颗粒基本是以弥散颗粒形式存在,颗粒停留时间分布较为均匀。通过将数值模拟结果与实验结果进行比较发现,模拟值与实验值吻合较好,说明所建立的数学模型较为合理,进一步通过数值模拟实验对颗粒密度和颗粒粒径对流动特性的影响规律进行了考察。     

流化床粉煤气体热载体快速热解反应器的计算

在冷态模拟实验和煤热解动力学计算的基础上,对粉煤气体热载体快速热解提升管反应器的高度进行了计算。利用高速摄像粒子测速法结合互相关算法研究了不同气体流量和不同颗粒粒径时固体颗粒在热解提升管中的运动速度,通过求解神府煤热解动力学方程,得到了不同粒径神府煤颗粒热解挥发分析出的时间,从而确定了快速热解提升管反应器的高度。研究结果表明:当气体流量在850 m3/h,粉煤的粒径主要集中在0.7—3.0 mm时,提升管的高度应选择在10.0 m。