海岸风沙流中不同粒径组沙粒的垂向分布模式

通过对河北昌黎黄金海岸沙丘风沙流的野外实地观测与室内风洞模拟实验数据的数值模拟,探讨了我国典型海岸沙丘风沙流中不同粒径组沙粒输沙量的垂向分布模式。结果表明,河北昌黎黄金海岸沙丘表面风沙流中不同粒径组沙粒输沙量的垂向分布特征并不一致,其中细沙和中沙符合典型的指数递减分布规律,但粗沙则为负幂函数分布。究其原因,主要与不同粒径组沙粒输沙量的分布高度及运动方式差异有关。在实际非均匀沙床面上,粗沙主要集中分布于沙丘表面4cm高度内湍流发育的近地表层,运动方式以蠕移为主,沙丘表面湍流的主导作用使其输沙量随高度的变化满足负幂律关系,但中沙和细沙则以跃移运动为主,跃移沙粒输沙量的垂向分布呈现指数递减特征。     

风沙流中不同粒径组沙粒的 输沙量垂向分布实验研究

在非均匀沙床面上, 风沙流中不同粒径组沙粒的输沙量垂向分布, 是非均匀风沙运动研究的重点。研究首先通过风洞实验, 收集了风洞中垂线垂向输沙量分布沙样, 然后对集沙沙样进行了沙粒粒度分析实验, 实验分析结果得出了不同粒径组沙粒的输沙量垂向分布规律, 基于稳定平衡风沙跃移运动模型和本文实验结果, 最后数值模拟研究了不同粒径组沙粒输沙量垂向分布, 与沙粒起跳速度和角度之间的关系。本文研究结果得出, 在非均匀风沙流中, 粗粒径组沙粒垂向输沙量上部符合指数递减分布但近床面区偏离指数分布, 呈现为偏大型分布, 粗粒径组对应的沙粒起跳速度和角度分布均为指数函数; 细粒径组沙粒垂向输沙量在整 个高度上均符合指数递减规律, 细粒径组沙粒对应的起跳速度分布为指数函数, 起跳角度分布为高斯函数。沙粒的平均起跳速度, 在0.4u*~2.2u* 之间变化, 随着气流风速(u*) 和沙粒粒径的增加而减小。     

VERTICAL DISTRIBUTION OF WIND-BLOWN SAND FLUX IN THE SURFACE LAYER,TAKLAMAKAN DESERT,CENTRAL ASIA

The vertical distribution of the wind-blown sand flux in a 40-cm flow layer above the ground surface was investigated through laboratory wind-tunnel tests and field measurements on the mobile dune surface during sand storms in the Taklamakan Desert of China. Results show that vertical distribution of the horizontal mass flux of drifting sand is a discontinuous function of height. More than 90% of the total material is transported in the flow layer from the surface to 14 cm. From 2 to 4 cm above the surface, a distinct transition zone occurs wherein mixed transport by creep, saltation, and suspension becomes saltation and suspension. The flow layer from 14 to 15 cm represents a further transition from saltation to suspension, where the distribution curves of the transport rate against height converge. The basic natural exponential function cannot describe well the vertical distribution of the saltation mass flux in the Taklamakan Desert. As a function of height, saltation mass flux follows a function q_salt = a'Z^-bZ, and the distribution of suspension mass flux fits the power function very well. A total transport rate from surface creep to saltation and suspension in the measured flow layer, which is directly proportional to the effective wind speed squared (V - V_t)², can be predicted by integrating Q = a'Z^-bZ + cZ^-d. The height distribution of the average quantities of transported materials varies as an exponential function of wind speed, and deceases with the increase in total transport quantity. Higher wind speed results in a higher transport rate and a higher vertical gradient for the particle concentration. The increment of relative transport quantity in the higher flux layer increases as wind speed increases, which generates a higher concentration of drifting particles in the upper flow layer. [Key words: aeolian geomorphology, aeolian transport, horizontal sand flux, sand dune, vertical sediment distribution, Taklamakan Desert.]     

Experimental investigation of the concentration profile of a blowing sand cloud

Detailed wind tunnel tests were carried out to establish the mean downwind velocity and transport rate of different-sized loose dry sand at different free-stream wind velocities and heights, as well as to investigate the vertical variation in the concentration of blowing sand in a cloud. Particle dynamic analyzer (PDA) technology was used to measure the vertical variation in mean downwind velocity of a sand cloud in a wind tunnel. The results reveal that within the near-surface layer, the decay of blown sand flux with height can be expressed using an exponential function. In general, the mean downwind velocity increases with height and free-stream wind velocity, but decreases with grain size. The vertical variation in mean downwind velocity can be expressed by a power function. The concentration profile of sand within the saltation layer, calculated according to its flux profile and mean downwind profile, can be expressed using the exponential function: c_z=ae^−bz, where c_z is the blown sand concentration at height z, and a and bare parameters changing regularly with wind velocity and sand size. The concentration profiles are converted to rays of straight lines by plotting logarithmic concentration values against height. The slope of the straight lines, representing the relative decay rate of concentration with height, decreases with an increase in free-stream wind velocity and grain size, implying that more blown sand is transported to greater heights as grain size and wind speed increase.     

稳态风沙流中瞬态输沙特征

风沙流中沙粒运动在来流风速不变时也会表现出非稳态特征。在风洞内利用粒子图像测速系统（PIV）测量了风沙运动的时间序列，并基于PIV测量技术提出风沙流中沙粒平均直径、数密度、平均水平速度和输沙通量等参数在某一时刻的计算方法，其中输沙通量的计算考虑沙粒大小垂向分布的影响。结果表明：来流风速不变时，沙粒平均直径、数密度、平均水平速度和输沙通量随时间具有明显的波动性；沙粒平均直径和平均水平速度的标准偏差一般随高度增加而增加，沙粒数密度和输沙通量标准偏差随高度增大而减小；这些参数的相对标准偏差均随高度增加而增大。     

尼龙网方格沙障风沙流携沙粒度的空间分异特征

为了探究塔克拉玛干沙漠腹地尼龙网方格沙障对风沙流携沙粒度的空间分异作用,于2015年4-6月,选取裸沙地和尼龙网2种下垫面,利用方口集沙仪和全方位集沙仪分别收集风沙流中垂直高度层中2~100 cm和16个方位的输沙量,利用BT-2001激光粒度分布仪对沙样进行粒度组成分析。结果表明：沙粒的粒度频率曲线形态表现为单峰分布特征,与下垫面沙粒组成有关。在垂直方向上,沙粒的平均粒径在L1（裸沙地）、L2（沙障前部）处随着高度的增加沙粒平均粒径减小,L3（沙障中部）处平均粒径先增加后趋于稳定;风沙流进入沙障后,分选性变差,偏度增大,峰度减小;L1和L2处沙粒随平均粒径的减小,分选性变差、细尾越来越明显、沙粒粒径分布范围变窄,且L1处分选系数、峰度和偏度与沙粒平均粒径在双变量图上的变化率大于L2处。在水平方位上,沙粒的平均粒径在T1（裸沙地）-T2（沙障前部）-T3（沙障中部）的过程中先增后减,在T2处,分选性最好,偏度系数和峰度最小;3个观测点的粒度参数与平均粒径没有明显的相关关系。     

Influence of soil texture on the binding energies of fine mineral dust particles potentially released by wind erosion

Models of the two aeolian processes (saltation and sandblasting) that lead to emission of fine dust particles (PM20) by wind erosion in arid and semi-arid areas have been combined to form the so-called ‘Dust Production Model’ (DPM). In this model, the size dependent binding energies of PM20 embedded within the wind-erodible loose soil aggregates or in the soil surface itself are key input parameters. Indeed, their values condition at the same time the intensity of emissions and their initial size distribution. Previous comparisons of vertical mass fluxes measured on-field with the model predictions suggest that these energies might be relatively independent of soil texture and also probably composition. Because this would greatly facilitate application of the DPM at regional or global scale, the objective of this work is to check experimentally the veracity of this result. The strategy that has been designed for this has involved selecting four natural soil samples collected in various source areas of the world and covering a wide range of textures and compositions. Then, these soil samples have been used to perform carefully controlled wind erosion simulations in a wind tunnel. During the experiments, which were carried out at different wind speeds with each soil, the horizontal flux (F_h) of saltating soil aggregates has been monitored. At the same time, number concentrations (C_i) of PM20 released by the sandblasting process were recorded in the 6 size classes of an optical size analyzer. Thus, the efficiency of the sandblasting process (defined as the ratio of C_i to F_h) could be determined for each of these size classes. Analysis of the results obtained in similar saltation conditions shows that for the four tested soils, and within the range of contents in clay and other components favoring aggregation (mostly organic matter and carbonates), the influence of soil composition and texture on binding energies of the PM20 particles within soil aggregates is at best a second order effect that can be neglected in large scale modeling of wind erosion by the DPM.     

The flux profile of a blowing sand cloud: a wind tunnel investigation

The flux profile of a blowing sand cloud, or the variation of blown sand flux with height, is the reflection of blown sand particles that move in different trajectories, and also the basis for checking drifting sand. Here we report the wind tunnel results of systematic tests of the flux profiles of different sized sands at different free-stream wind velocities. The results reveal that within the 60-cm near-surface layer, the decay of blown sand flux with height can be expressed by an exponential function: q_h=aexp(−h/b), where, q_h is the blown sand transport rate at height h, a and b are parameters that vary with wind velocity and sand size. The significance of coefficient a and b in the function is defined: a represents the transport rate in true creep and b implies the relative decay rate with height of the blown sand transport rate. The true creep fraction, the ratio of the sand transported on the surface (h=0) to the total transport varies widely, decreasing with both sand size and wind speed. The flux profiles are converted to straight lines by plotting sand transport rate, q_h, on a log-scale. The slope of the straight lines that represents the relative decay rate with height of sand transport rate decreases with an increase in free-stream wind velocity and sand grain size, implying that relatively more of the blown sand is transported to greater heights as grain size and wind speed increase. The average saltating height represented by the height where 50% of the cumulative flux percentage occurs increases with both wind speed and grain size, implying that saltation becomes more intense as grain size and/or wind velocity increase.     

海滩养护影响下的海岸风沙堆积——以福建平潭岛龙凤头海滩养护工程为例

海滩养护工程实施后,在保护海岸抵御侵蚀的同时往往还产生其他的环境问题。尤其在强风区海岸,海滩养护造成了滩面环境的改变,使滩面风沙搬运和沉积特征都发生了显著变化。对福建平潭岛龙凤头海滩养护工程实施前后的风沙沉积对比研究表明,养护后海滩的干滩宽度、滩面沉积物粒径、表层湿度、海滩高程等环境要素变化对滩面风沙搬运与沉积过程都产生了重要的影响。主要结论为:(1)养护海滩干滩滩肩高程的提高增加了滩面风速,增大了滩面风沙输沙率;(2)养护海滩干滩宽度的增加既扩大了风区长度也为风沙搬运提供了充足的物源,且不受潮汐过程影响,提供了持续的风沙物源供给,增加了风沙作用时间;(3)养护海滩剖面形态的变化使得海滩滩面沉积物含水率减小,降低风沙起动风速,增强了滩面风沙搬运。     

The harmonious character in equilibrium aeolian transport on mixed sand bed

Wind tunnel experiments were carried out to measure the spatial distribution in equilibrium transport of four types of mixed sand. The flux profiles of each grain size group were calculated. It is found that the vertical distribution of mean grain size has a close relation with the grain size distribution in the sand bed. In a log-linear plot, the flux profiles of main grain size groups are all straight lines and their slopes are nearly equal. It is also found that the ratio of transport rate of each size group to the whole transport rate is directly proportional to the mass ratio of each size group in the sand bed and the proportion value is only dependent on the grain size. This harmonious law is applicable to all four types of mixed sand used in the experiment.     

基于高速摄影技术的风沙流输沙通量剖面的风洞实验测量

风沙研究者非常重视对输沙通量随高度变化特征的研究,并为寻找可靠的测量手段付出了不懈的努力。基于高速摄影技术获得的沙粒平均水平速度与沙粒数的垂直剖面,推导了较低风速下环境风洞内输沙通量的垂直剖面。结果表明：沙粒平均水平速度随高度呈幂函数增加,颗粒浓度随高度的算数平方根呈指数衰减。由颗粒平均水平速度剖面与浓度剖面的乘积可获得输沙通量剖面。所获得的输沙通量随高度变化曲线在距床面1~3 mm处均有一个明显的拐点,拐点上方输沙通量随高度呈指数衰减。在床面与拐点之间输沙通量没有明显的变化趋势,这可能是由于气流中颗粒间的碰撞以及颗粒与床面碰撞的影响。平均跃移高度和相对衰减系数是描述输沙通量随高度变化的两个重要参数,两者有着很好的相关性,表明了随着风速增加和沙粒粒径减小跃移颗粒可以达到更大的高度,随着风速减小与粒径增大,输沙通量迅速衰减。     

Height profile of the mean velocity of an aeolian saltating cloud: Wind tunnel measurements by Particle Image Velocimetry

The velocity of saltating particles is an important parameter in studying the aeolian sand movement. We used Particle Image Velocimetry to measure the variation with height of the mean particle velocity of a saltating cloud over a loose sand surface in a wind tunnel. The results suggest that both the horizontal and vertical particle velocities fit the Gaussian distribution well, and that the mean particle velocity of a saltating cloud varies with wind velocity, particle size and the height above bed. The mean horizontal velocity is mainly the result of acceleration by the wind and increases with an increase in friction wind velocity but decreases with an increase in grain size because greater wind velocity causes more acceleration and finer particles are more easily accelerated at a given wind velocity. It also increases with an increase in height by a power function, in agreement with previous results obtained by other methods such as the high-speed multi-flash photographic method and Particle Dynamics Analyzer (PDA), reflecting, first, the increase in wind velocity with height through the boundary layer, and second, the longer trajectory-particle path length increases with height and affords a longer time for acceleration by the wind. An empirical model relating the mean horizontal particle velocity and height, friction wind velocity as well as particle size is developed. The ratio of the mean horizontal particle velocity to the clean wind velocity at the same height increases with height but decreases with grain size. The magnitude of mean vertical velocity is much less (one or two orders less) compared with the mean horizontal velocity. The average movement in the vertical direction of a saltating cloud is upward (the mean vertical velocity is positive). Although the upward velocity of a saltating particle should decrease with height due to gravity the mean vertical (upward) velocity (the average of both ascending and descending particles) generally shows a tendency to increase with height. It seems that at higher elevations the data are more and more dominated by the ‘high-flyers’. The underlying mechanism for the mean vertical velocity distribution patterns needs to be clarified by further study.     

兰新高铁烟墩风区戈壁近地表风沙流跃移质垂直分布特性

跃移质作为风沙流的主体,其近地表垂直分布规律是风沙物理学的重要研究内容,对防沙工程具有重要的指导意义。受研究条件与观测仪器限制,戈壁特别是极端大风区近地表风沙流结构特性研究较为薄弱。利用多梯度风蚀传感器与阶梯式集沙仪对兰新高铁烟墩风区戈壁近地表风沙流跃移质的垂直分布特性进行了观测研究。结果表明：兰新高铁烟墩风区戈壁沙粒发生跃移运动的2 m高临界风速达12 m·s^-1;戈壁近地表风沙流具有明显的阵性特征,沙粒跃移发生的时间比例在50%以下,与平均风速成正相关关系,与风速脉动强度无显著相关关系;2 m高阵风7级风速下,戈壁跃移沙粒主要集中于地表50 cm范围内,近地表风沙流结构呈"象鼻效应",跃移质最大质量通量出现在地表2.5~5 cm高度处,沙粒最大跃移高度可达2 m,且沙粒跃移高度随2 m高风速的增加呈指数规律递增。因此,兰新高铁烟墩风区2 m高阻沙栅栏不足以完全阻截戈壁风沙流,是造成烟墩风区兰新高铁轨道积沙的重要原因之一。     

The assessment of weathering stages in granites using an EC/pH meter

The sidewall effects of a wind tunnel on aeolian sand transport were investigated experimentally. A wind tunnel was used to conduct the experiments with a given channel height of 120 cm and varying widths (B) of 40, 60, 80, 100 and 120 cm. Both vertical profiles of wind velocity and sand mass flux were measured at different locations across the test section. The results show that the wind velocity with saltation first increases and then decreases to a minimum, from the sidewall to the central line of the wind tunnel. The discrepancy among wind velocities at different locations of the transverse section decreases with decreasing tunnel width. The wind friction velocity across the wind tunnel floor, with the exception of the region closest to the sidewalls, does not deviate strongly in wide wind tunnels from that along the central line, whereas it does vary in narrow tunnels. The sand mass fluxes, with the exception of some near-bed regions, are larger along the central line of the wind tunnel than they are at the quarter width location from the sidewall. Unlikely previously reported results, the dimensionless sand transport rate, Qg / (ρu³) (where Q is the total sand transport rate, g is the gravitational acceleration constant, ρ is the air density, and u is the wind friction velocity), first decreases and then increases with the dimensionless friction velocity, u / u_t (where u_t is the threshold friction velocity). The above differences may be attributed to the sidewall effects of the wind tunnel. A dimensionless parameter, F_B = u / (gB)^1/2, is defined to reflect the sidewall effects on aeolian sand transport. The flows with F_B of 0.33 or less may be free from the sidewall effects of the wind tunnel and can ensure accurate saltation tunnel simulation.     

Determination of grid size for digital terrain modelling in landscape investigations—exemplified by soil moisture distribution at a micro-scale

The central problem of a combined analysis of digital terrain models (DTMs) and other landscape data is determination of a DTM grid size (w) providing a correct study of relationships between topographic variables and landscape properties. Generally, an adequate w is determined by an expert estimate, and solutions are largely subjective. We developed an experimental statistical method to determine an adequate w for DTMs applied to landscape studies. The method includes the following steps: (a) derivation of a DTM set using a series of w_i , (b) performance of a correlation analysis of data on a landscape property and a topographic variable estimated with various w_i , (c) plotting of correlation coefficients obtained versus w, and (d) determination of smoothed plot portions indicating intervals of an adequate w. We applied the method developed to study the ifluence of topography on the spatial distribution of soil moisture (M) at a micro-scale. We investigated the dependence of M on gradient (G), horizontal (k_h ), vertical (k_v ), and mean (H) landsurface curvatures. For DTM derivation, we used 13 values of w_i from 1 to 7m. An interval of adequate w_i for M falls between 2.25 and 3.25m in the given terrain conditions. In absolute magnitudes, correlation coefficients are largest within this interval; correlation coefficients of M with G, k_h , k_v and H are 0.28, 0.52, 0.50 and 0.60, respectively, for w = 3m. The results obtained demonstrate that the method actually works to identify an adequate w at a micro-scale. The method developed allows estimation of an adequate area of landform which realise a topographic control of landscape properties.     

人工卵石床面风沙流粒度特征

沉积物粒径分布对风沙沉积物的起动、输送和沉降过程十分重要。不同粒径的风沙沉积物空气动力学特征不同,从而导致其起动机理、输送过程和沉降模式不同。因此,粒度可以作为风沙沉积过程的指示器。戈壁是西北地区的一种重要地貌景观,戈壁风沙流是风沙物理研究的内容之一,但目前研究较少,特别是对戈壁风沙流粒度分布的研究,几乎没有报道。本文利用人工卵石床面模拟戈壁地表,对0.25、0.5、1 m和2 m高度的风沙流粒度特征进行观测,结果表明：沙源、地表状况、风程效应等影响沙粒粒径随高度的变化。沙源近,平均粒径随高度先减小后增加;沙源远,平均粒径随高度增加减小。戈壁表面的不同区域,沙粒粒径级配不同：随高度增加,粗砂,中砂含量降低,细砂、极细砂和粉砂含量增加;随距离增加,中砂含量降低,细砂、极细砂和粉砂含量增加。平均粒径越大,分选越好,偏度越趋于正偏,峰度越趋于变宽。偏度、峰度随分选系数增加而增加。峰度随偏度增加而增加。     

柴达木盆地西北部长垄状雅丹沉积物粒度特征

雅丹是干旱区常见的风蚀地貌，也是风沙地貌学界关注和争论的焦点。以柴达木盆地西北部冷湖地区的典型长垄状雅丹为对象，对其出露剖面的沉积物粒度特征进行了研究。结果表明：长垄状雅丹沉积物中粉沙组分含量最高，平均为44.03%；沙粒组分含量次之，平均为35.99%；黏粒组含量最低，平均为19.98%。沉积物频率曲线既有主次峰明确的双峰分布曲线，也有主次峰不明确的双峰和单峰分布曲线；前者可能为风力搬运堆积形成的沉积物，后两种曲线宽平，沉积物分选性差，可能为湖相沉积形成。沉积粒度参数在垂直剖面呈现出一定的变化规律，但是粒度参数之间没有显著的相关关系。长垄状雅丹沉积物呈明显的软硬岩层（即沙质亚砂土与粉质黏土或沙质亚黏土与粉质亚黏土）互层的现象，这为风力的吹蚀和磨蚀作用创造了有利条件。     

Sampling efficiency of vertical array aeolian sand traps

Previous investigations have indicated that the sampling efficiency of aeolian sand traps is low and varies greatly in the near-bed region. Outside this region, the efficiency tends to be consistently higher for all types of trap. An evaluation was carried out to compare the sampling efficiency of different types of aeolian sand trap based on the comparison of the “actual” and the measured sand mass flux profiles, with emphasis on the single-tube vertical array trap, conventional array trap, and step-like array trap. A simple formula is proposed to express the actual vertical profile of sand mass flux, which has been validated with the unique data obtained with an isokinetic trap by [Sedimentology 45 (1998) 789]. Using the experimental data collected by the present authors and those by other investigators, sampling efficiencies of three types of trap are examined in terms of the frequency distribution of all the samples. For the single-tube traps, the sampling efficiency varies from 65% to 95%, with a mode at 75%. For both the conventional array and step-like array traps, sampling efficiencies range from 15% to 85%, with the modal frequencies at 35% and 75%, respectively. This review seems to suggest that the peak frequency with higher sampling efficiency coincides with the maximum sand-grain Reynolds number.     

Evaluation of saltation flux impact responders (Safires) for measuring instantaneous aeolian sand transport intensity

The measurement of aeolian sand transport rates on small scales is of interest to the development and testing of detailed models of sand movement by wind. This paper reports on laboratory evaluations and preliminary field tests of a new design of a piëzo-electric impact responder, called a ‘Safire’, capable of measuring saltation impacts at a frequency of 20 Hz. The advantages of the Safire are: (1) that it provides high-frequency measurements, (2) that it presents a minimal obstruction to the wind flow (no scour observed in the field), and (3) that it is of a (relatively) low-cost.Laboratory calibrations were performed with a vertical gravity flume generating known sand grain fluxes using both mixed sand and specific size fractions. Initial tests investigated three fundamental characteristics: correspondence between digital and analogue signals generated by the instrument, directional response of the probe, and linearity of instrument response to mass flux.Instrument calibration included determination of the momentum threshold required for the sensor to register a grain impact. Based on this lower limit and the known distribution of grain size and speed at different fall heights, a prediction is made as to the sand grain flux the Safire ought to measure, which is then compared with the signal response. The result of this comparison is an assessment of the instrument's efficiency in counting saltating grains. These Safires were also deployed in the field as part of a larger investigation of spatio-temporal transport variability. This experiment provided the opportunity to compare the instrument's performance with traditional sand traps, and this paper develops methods and assumptions required to convert measurements from impact responders to traditional mass transport rates.The evaluations indicate that improvements to the instrument production process are required to ensure a standard momentum threshold among individual instruments. Furthermore, the sensor design needs to be reconsidered in order to eliminate the variation in response depending on azimuth direction, so that the sensor is uniformly omni-directional.     

风沙流输沙通量垂向分布研究 ——以塔克拉玛干沙漠南缘流沙地表风沙流观测为例

 于2010年4—6月在塔克拉玛干沙漠南缘策勒绿洲外缘流沙地进行风速、风向和输沙量同步观测,利用观测到的28组数据对输沙通量的垂向分布进行研究。结果表明,在4.5～8 m·s-1的风速区间内,总输沙率随风速增长速率较慢,大于8  m·s-1时增长迅速。在较小风速时,4个高度层(1 cm、3 cm、9 cm和19 cm)的输沙比率变化不明显,当风速大于6.6 m·s-1时,1 cm和19 cm高度输沙比率的调整较为明显,前者减小而后者增加,中间两层(3 cm、9 cm)则维持一定波动。不同的蚀积条件对于输沙通量的垂向分布具有一定的影响,平均跃移高度则在一定程度上反映了地表沙粒的吹蚀和堆积过程。在4种常见的描述输沙通量垂向分布的模型中,Zingg的修正幂函数具有最好的拟合程度,但反映的风沙流信息最少,简单幂函数的参数包涵了最为丰富的风沙流信息但拟合程度最差,指数函数同时具有较好的拟合程度和参数意义,Fryrear的幂函数则与指数函数恰恰相反。在沙物质以极细沙为主的塔克拉玛干沙漠南缘,指数函数较之简单幂函数能更好地描述该区域输沙通量的垂向分布,验证并补充了风洞实验的结果。综合比较认为,指数函数能更好地描述塔克拉玛干沙漠南缘输沙通量的垂向分布。