High-temperature tribological properties of spark-plasma-sintered Al2O3 composites containing barite-type structure sulfates

Al₂O₃–50BaSO₄–20Ag, Al₂O₃–50BaSO₄–10SiO₂, Al₂O₃–50(mass%)SrSO₄, Al₂O₃–50PbSO₄–5SiO₂, Al₂O₃–50BaSO₄ and Al₂O₃–50BaCrO₄ composites (mass%) were prepared by spark plasma sintering and their microstructure and high-temperature tribological properties were evaluated. Al₂O₃–50BaSO₄–20Ag composites (mass%) showed the lowest friction coefficients at the temperature ranging from 473 to 1073 K. Thin Ag film was observed on the wear tracks of the composites above 473 K. In addition, the friction coefficients of Al₂O₃ composites containing SrSO₄ and PbSO₄ were as low as those of Al₂O₃–BaSO₄ and Al₂O₃–BaCrO₄ composites at the temperatures up to 1073 K. The thin films formed on the wear tracks of the Al₂O₃–SrSO₄ composites were composed of Al₂O₃ and SrSO₄ phases, while the films formed on the wear tracks of the Al₂O₃–PbSO₄–SiO₂ composites consisted of Al₂O₃, PbSO₄ and SiO₂ phases.     

Tribological Behavior of PTFE Composites Filled with PEEK and Nano-Al2O3

In this study, the tribological properties of polytetrafluoroethylene (PTFE) composites filled with polyetheretherketone (PEEK) and nano-Al₂O₃ particles were studied using a block-on-ring wear tester. The tribological performance of the composites was affected by the experimental parameters (sliding speed, normal load, and environmental temperature) and the composites achieved a high-speed sliding friction state. The results showed that the PEEK and nano-Al₂O₃ particles significantly improved the wear resistance of the PTFE composites. In addition, the nano-Al₂O₃ particles increased the hardness of the composites and enhanced the mechanical properties to enable applications in a wider range of industrial fields. The effects of the sliding speed and normal load on the tribological properties were more significant than that of the environmental temperature. In addition, the entire wear process was divided into three stages (the initial wear stage, severe wear transition stage, and ultralow stable wear stage), according to the evolution of the tribological characteristics (wear rate, morphology of the worn surface and transfer film, and wear debris morphology).     

Fretting wear behaviors of nanometer Al2O3 and SiO2 reinforced PEEK composites

The influence of diameter and content of Al₂O₃ particles on the tribological behaviors under fretting wear mode was investigated. The surface of PEEK composite and steel ball were examined by SEM and EDS, to identify the topography of wear scar and analyze the distribution of chemical elements in the friction counterparts, respectively. It can be found that the filling of Al₂O₃ powder improves the fretting wear resistance of PEEK composite. With the increase of Al₂O₃ diameter, the area of wear scar on specimen increases first and decreases afterward. However, the wear of composites increases monotonically with increasing Al₂O₃ content. Although the filling of 10 wt.% and 200 nm PTFE powder in PEEK makes the lowest wear of all specimens, no synergistic effect was found when Al₂O₃ and PTFE were filled into PEEK composite together. For the friction pair of PEEK composite and steel ball, abrasive wear and adhesive wear dominate the fretting wear mechanism during fretting. Thermal effect plays a very important role during fretting; thus the property of temperature resistance for polymer material would affect the wear degree on the surface of wear scar.     

纳米粒子及PTFE填充PEEK复合材料摩擦特性的载荷和时间依赖性

以热压成型法制备了纳米Al2O3和纳米TiO2分别与聚四氟乙烯(PTFE)填充PEEK复合材料,利用自制销-盘摩擦磨损试验机研究了干摩擦条件下复合材料的摩擦行为。结果表明：复合材料的摩擦因数依赖于材料中纳米粒子的种类和含量,并对载荷有明显的依赖性;当纳米Al2O3的质量分数为5％～7％时,PEEK复合材料的摩擦因数和比磨损率最低;随着外加载荷的变化,摩擦因数呈现一定的变化规律。     

Sliding friction and wear performance of Ti6Al4V in the presence of surface-capped copper nanoclusters lubricant

The friction and wear properties of Ti₆Al₄V sliding against AISI52100 steel ball under different lubricative media of surface-capped copper nanoclusters lubricant—Cu nanoparticles capped with O,O′-di-n-octyldithiophosphate (Cu-DTP), rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP was evaluated using an Optimol SRV oscillating friction and wear tester. The wear mechanism was examined using scanning electron microscopy (SEM) and X-ray photoelectron spectrosmeter (XPS). Results indicate that Cu-DTP can act as the best lubricant for Ti₆Al₄V as compared with rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP. The applied load and sliding frequency obviously affected the friction and wear behavior of Ti₆Al₄V under Cu-DTP lubricating. The frictional experiment of the Ti₆Al₄V sliding against AISI52100 cannot continue under the lubricating condition of rapeseed oil or rapeseed oil containing 1 wt% Cu-DTP when the applied load are over 100 N. Surprisingly, the frictional experiment of Ti₆Al₄V sliding against AISI52100 steel can continue at the applied load of 450 N under Cu-DTP lubricating. The tribochemical reaction film containing S and P is responsible for the good wear resistance and friction reduction of Ti₆Al₄V under Cu-DTP at the low applied load. However, a conjunct effect of Cu nanoparticle deposited film and tribochemical reaction film containing S and P contributes to the good tribological properties of Ti₆Al₄V under Cu-DTP at the high-applied load.     

Tribological characteristics of low-pressure plasma-sprayed A12O3 coating from room temperature to 800 °C

The tribological characteristics of low-pressure plasma-sprayed (LPPS) Al₂O₃ coating sliding against alumina ball have been investigated from room temperature to 800 °C. These friction and wear data have been compared quantitatively with those of bulk sintered alumina to obtain a better understanding of wear mechanisms at elevated temperatures. The friction and wear of Al₂O₃ coating show a strong dependence on temperature, changing from a mild to a severe wear regime with the increase of temperature. The coefficient of friction at room temperature is approximately 0.17 to 0.42, depending on applied load. The tribochemical reaction between the coating surface and water vapor in the environment and the presence of the hydroxide film on the Al₂O₃ coating reduce the friction and wear at room temperature as contrasted to those of bulk sintered alumina. At intermediate temperatures, from 400 to 600 °C, the friction and wear behavior of Al₂O₃ coating depends on the inter-granular fracture and pull-out of Al₂O₃ grains. At above 700 °C, formation and deformation of fine grain layer, and abrasive wear in the form of removal of fine alumina grains further facilitate the friction and wear process of Al₂O₃ coating.     

The friction and wear properties of nanometre SiO2 filled polyetheretherketone

Nanometre SiO₂ filled-polyetheretherketone (PEEK) composite blocks with different filler proportions were prepared by compression moulding. Their friction and wear properties were investigated on a block-on-ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The morphologies of the wear traces and the transfer film were observed by scanning electron microscopy (SEM). It was found that nanometre SiO₂ filled-PEEK exhibited considerably lower friction coefficient and wear rate in comparison with pure PEEK. The lowest wear rate was obtained with the composite containing 7.5 wt.% SiO₂. The SEM pictures of the wear traces indicated that with the frictional couple of carbon steel ring/composite block (fillec with 7.5 wt.% filler), a thin, uniform, and tenacious transfer film was formed on the ring surface. It was inferred that the transfer film contributed largely to the decreased friction coefficient and wear rate of the filled PEEK composites.     

The effect of Al2O3 on the friction performance of automotive brake friction materials

This study consists of two stages. In the first stage, bronze-based break linings were produced and friction-wear properties of them were investigated. In the second stage, 0.5%, 1%, 2% and 4% alumina (Al₂O₃) powders were added to the bronze-based powders and Al₂O₃ reinforced bronze-based break linings were produced. Friction–wear properties of the Al₂O₃ reinforced samples were aslo investigated and compared to those of plain bronze-based ones. For this purpose, friction coefficient and wear behaviour of the samples were tested on the grey cast iron disc. The hardness and density of the samples were also determined. Microstructures of the samples before and after the sintering and the worn surfaces of the wear specimens were examined using a scanning electron microscope (SEM). The sample compacted at 350 MPa and sintered at 820 °C exhibited the optimum friction–wear behaviour. With increase in friction surface temperature, a reduction in the friction coefficient of the samples was observed. The lowest reduction in the friction coefficient with increasing temperature was for the 2% and 4% Al₂O₃ reinforced samples. The SEM images of the sample indicated that increase in Al₂O₃ content resulted in adhesive wear. With increase in Al₂O₃ content, a reduction in mass loss of the samples was also observed. Overall, the samples reinforced with 2% and 4% Al₂O₃ exhibited the best results.     

Study on the tribological behavior of hybrid PTFE/cotton fabric composites filled with Sb2O3 and melamine cyanurate

The tribological behavior of the hybrid PTFE/cotton fabric composites filled with microsize Sb₂O₃ and melamine cyanurate (MCA) was investigated. It was found that the wear rate of the hybrid PTFE/cotton fabric composites decreased when Sb₂O₃ was used as the filler but increased with MCA filler. It was also observed that hybrid fillers (consists of Sb₂O₃ and MCA) had a wear reduction effect on the hybrid PTFE/cotton fabric composites at lower loads but increased the wear rate at higher loads. The wear behavior of the composites was explained in terms of the topography of worn surfaces and transfer film formed on the counterpart pin.     

Friction and wear characteristics of lead and its compounds filled polytetrafluoroethylene composites under oil lubricated conditions

The friction and wear properties of Pb, PbO, Pb₃O₄, or PbS filled polytetrafluoroethylene (PTFE) composites sliding against GCr15 bearing steel under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester. The worn surfaces and the transfer films of these PTFE composites formed on the surface of GCr15 bearing steel were then investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that filling Pb, PbO, Pb₃O₄ or PbS to PTFE can greatly reduce the wear of the PTFE composites, but the wear reducing action of Pb₃O₄ is the most effective. Meanwhile, PbS increases the friction coefficient of the PTFE composite, but Pb and Pb₃O₄ reduce the friction coefficients of the PTFE composites. However, the friction and wear properties of lead or its compounds filled PTFE composites can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of the PTFE composites can be decreased by one order of magnitude. Optical microscope investigation of transfer films shows that Pb, PbO, Pb₃O₄ and PbS enhance the adhesion of the transfer films to the surface of GCr15 bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of GCr15 bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. SEM examination of worn surfaces shows that the interaction between liquid paraffin and the PTFE composites creates some cracks on the worn surfaces of the PTFE composites; the creation and development of the cracks reduces the load-carrying capacity of the PTFE composites, and this leads to deterioration of the friction and wear properties of the PTFE composites filled with lead or its compounds under higher loads in liquid paraffin lubrication.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

Sliding wear characteristics of plasma-sprayed Al2O3 and Cr2O3 coatings against copper alloy under severe conditions

Al₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying and their tribological properties dry sliding against copper alloy were evaluated using a block-on-ring configuration at room temperature. It was found that the wear resistance of Al₂O₃ coating was superior to that of the Cr₂O₃ coating under the conditions used in the present study. This mainly attributed to its better thermal conductivity of Al₂O₃ coating, which was considered to effectively facilitate the dissipation of tribological heat and alleviate the reduction of hardness due to the accumulated tribological heat. As for the Al₂O₃ coating, the wear mechanism was plastic deformation along with some micro-abrasion and fatigue-induced brittle fracture, while the failure of Cr₂O₃ coating was predominantly the crack propagation-induced detachment of transferred films and splats spallation.     

Influence of Al2O3 reinforcement on the abrasive wear characteristic of Al2O3/PA1010 composite coatings

In the present study, the abrasive wear characteristics of Al₂O₃/PA1010 composite coatings were tested on the turnplate abrasive wear testing machine. Steel 45 (quenched and low-temperature tempered) was used as a reference material. The experimental results showed that when the Al₂O₃ particles have been treated with a silane coupling agent (γ-aminopropyl-triethoxysilane), the abrasive wear resistance of Al₂O₃/PA1010 composite coatings has a good linear relationship with the volume fraction of Al₂O₃ particles in Al₂O₃/PA1010 composite coatings and the linear correlation coefficient is 0.979. Under the experimental conditions, the size of Al₂O₃ particles (40.5-161.0 μm) has little influence on the abrasive wear resistance of Al₂O₃/PA1010 composite coatings. By treating the surface of Al₂O₃ particles with the silane coupling agent, the distribution of Al₂O₃ particles in PA1010 matrix is more homogeneous and the bonding state between Al₂O₃ particles and PA1010 matrix is better. Therefore, the Al₂O₃ particles make the Al₂O₃/PA1010 composite coatings have better abrasive wear resistance than PA1010 coating. The wear resistance of Al₂O₃/PA1010 composite coatings is about 45% compared with that of steel 45.     

Friction and wear behaviour of Thordon XL and LgSn80 in sliding against plasma-sprayed Cr2O3 coatings

This paper studies the friction and wear behaviour of two important bearing materials, Thordon XL and LgSn80, in dry and lubricated sliding vs. plasma-sprayed Cr₂O₃ coatings. As a reference, AISI 1043 steel is also studied under the same conditions. SEM, EDS and surface topography were employed to study the wear mechanisms. The results indicate that the Thordon XL/Cr₂O₃ coating pair gives the lowest dry friction coefficient (0.16) under a normal load of 45.3 N (pressure 0.453 MPa) at a velocity of 1 m/s. The dry friction coefficient of Thordon XL/Cr₂O₃ coating increases to 0.38 under a normal load of 88.5 N (pressure 0.885 MPa). The dry friction coefficients of the LgSn80/Cr₂O₃ coating are in the range of 0.31–0.46. Secondly, both dry wear rate under low normal load (45.3 N) and lubricated wear rate under a load of 680 N for Thordon XL are lower than those of LgSn80 in sliding against plasma-sprayed Cr₂O₃ coatings at a speed of 1 m/s. However, under a normal load of 88.5 N the dry wear rate of Thordon XL is much higher than that of LgSn80. Thirdly, a high viscosity lubricant (SAE 140) leads to lower wear for Thordon XL and LgSn80 than a low viscosity lubricant (SAE 30). Finally, the dominating wear mechanism for Thordon XL is shear fracture when against the plasma-sprayed Cr₂O₃ ceramic coating. For LgSn80 against plasma-sprayed Cr₂O₃ ceramic coating, abrasive wear is the governing failure mechanism.     

Wear properties of two-phase Al2O3/ZrO2 (Y2O3) ceramics at temperatures from 296 to 1073 K

Reciprocating sliding friction experiments were conducted with various two-phase, directionally solidified Al₂O₃/ZrO₂ (Y₂O₃) pins sliding on B₄C flats in air at temperatures of 296, 873, and 1073 K under dry sliding conditions. Results indicate that all the Al₂O₃/ZrO₂ (Y₂O₃) ceramics, from highly Al₂O₃-rich to ZrO₂-rich, exceed the main wear criterion requirement of 10⁻⁶ mm³ N⁻¹ m⁻¹ or lower for effective wear-resistant applications. Particularly, the eutectics and Al₂O₃-rich ceramics showed superior wear properties. The composition and microstructure of Al₂O₃/ZrO₂ (Y₂O₃) ceramics played a dominant role in controlling the wear and friction properties. The controlling mechanism of the ceramic wear, friction, and hardness was an intrinsic effect involving the resistance to shear fracture of heterophase bonding and cohesive bonding and the interlocking microstructures at different scales in the ceramics.     

Sliding contacts for the pharmaceutical industry: failure analysis and dry sliding tests for the replacement of hard Cr on AISI 316L steel

Several alternatives were compared for the replacement of hard electroplated Cr coating to improve the tribological properties of the AISI 316L austenitic stainless steel for pharmaceutical packaging applications, including low temperature carburizing (LTC), thermal spray coatings (Al₂O₃-13TiO₂, WC-17Co), substitution of the AISI 301 reference counterface with polymeric materials (PTFE, UHMWPE, PEEK). In dry sliding block on ring tests, the LTC AISI 316L cylinders lead to the lowest wear rates of the AISI301 sliders under low loads (up to 10 N). When considering the polymer vs. uncoated AISI 316L couple, PEEK and UHMWPE lead to lower friction and comparable wear rates with respect to the reference couple (AISI 301 vs. Hard Cr coated-AISI 316L) in the whole range of tested loads.     

Comparison of wear behaviour of plasma-sprayed Al2O3 coatings with and without laser treatment

This paper studies experimentally the effects of CO₂ laser-treatment on the wear behaviour of plasma-sprayed Al₂O₃ coatings, in linear contact sliding (dry, abrasive and lubricated) against SAE 4620 steel. Tests were carried out using a block-on-ring friction and wear tester, under different loads at different speeds. The wear mechanism and the changes in adherence, porosity and microstructure by laser treatment were also investigated. Results show a better wear behaviour for both laser-treated ceramic coating and its paired steel under dry and abrasive conditions, compared with the case without laser treatment. The lubricated wear behaviour of the laser-treated ceramic coating, however, is not improved. The changes in microhardness, porosity and adherence caused by the laser treatment are responsible for the change in wear behaviour of the ceramic coating.     

Friction and wear behaviour of plasma-sprayed Cr2O3 coatings against steel in a wide range of sliding velocities and normal loads

This study investigates the influence of sliding speed and normal load on the friction and wear of plasma-sprayed Cr₂O₃ coatings, in dry and lubricated sliding against AISI D2 steel. Friction and wear tests were performed in a wide speed range of 0.125–8 m/s under different normal loads using a block-on-ring tribometer. SEM, EDS and XPS were employed to identify the mechanical and chemical changes on the worn surfaces. A tangential impact wear model was proposed to explain the steep rising of wear from the minimum wear to the maximum wear. The results show that the wear of Cr₂O₃ coatings increases with increasing load. Secondly, there exist a minimum-wear sliding speed (0.5 m/s) and a maximum-wear sliding speed (3 m/s) for a Cr₂O₃ coating in dry sliding. With the increase of speed, the wear of a Cr₂O₃ coating decreases in the range 0.125–0.5 m/s, then rises steeply from 0.5 m/s to 3 m/s, followed by a decrease thereafter. The large variation of wear with respect to speed can be explained by stick-slip at low speeds, the tangential impact effect at median speeds and the softening effect of flash temperature at high speeds. Thirdly, the chemical compositions of the transfer film are a-Fe₂O₃ in the speed range 0.25–2 m/s, and FeO at 7 m/s. In addition, the wear mechanisms of a Cr₂O₃ coating in dry sliding versus AISI D2 steel are adhesion at low speeds, brittle fracture at median speeds and a mixture of abrasion and brittle fracture at high speeds. Finally the lubricated wear of Cr₂O₃ coating increases sharply from 1 to 2.8 m/s.     

Effects of anti-wear additives on friction and wear properties of Cr2O3 coating

The effects of some anti-wear additives on the friction and wear behaviour of plasma-sprayed Cr₂O₃ coating were investigated using a block-on-ring tester at ambient conditions. The results show that zinc dialkyldithiophosphate (ZDDP), tricesyl phosphate (TCP) and tributyl phosphate (TBP) significantly reduce the wear of Cr₂O₃ coating lubricated by paraffin oil. Additive concentrations as well as sliding time have great influence on the wear. The friction coefficient varies slightly with test conditions. The analysis by XPS of worn surfaces indicates that the wear resistance of these additives is due to the formation of tribochemical reaction films by reacting with Cr₂O₃ coatings.     

Microstructural and Tribological Properties of A356 Al–Si Alloy Reinforced with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Particles

In the present study, the effect of the Al₂O₃ particles (average size of 12 μm, 3 and 10 wt.%) reinforcement on the microstructure and tribological properties of Al–Si alloy (A356) was investigated. Composites were produced by applying compocasting process. Tribological properties of unreinforced alloy and composites were studied, using pin-on-disc tribometer, under dry sliding conditions at different specific loads and sliding speed of 1 m/s. Microhardness measurements, optical microscope and scanning electron microscope were used for microstructural characterization and investigation of worn surfaces and wear debris. During compocasting of A356 alloy, a transformation from a typical dendritic primary α phase to a non-dendritic rosette-like structure occurred. Composites exhibited better wear resistance compared with unreinforced alloy. Presence of 3 wt.% Al₂O₃ particles in the composite material affected the wear resistance only at specific loads up to 1 MPa. The wear rate of composite with 10 wt.% Al₂O₃ particles was nearly two order of the magnitude lower than the wear rate of the matrix alloy. Dominant wear mechanism for all materials was adhesion, with others mechanisms: oxidation, abrasion and delamination as minor ones.