Two-body abrasive wear of electroless nickel composite coatings

The two-body abrasive wear of electroless nickel (EN), EN-silicon carbide, and EN-alumina composite coatings have been investigated using a scratch test with a diamond indenter. The coatings were heat treated at temperatures of 100–500° C. The hardness of the coatings increased with heat treatment temperature from 500 HV100 for the as-deposited condition to 1008 HV100 when fully hardened. Scratch testing showed that the as-deposited coating had scratch tracks with a high degree of plasticity, signs of microploughing and tensile cracking and was characterised as a ductile failure. On the other hand, the heat-treated coatings showed chipping and cracking on the edge of the scratch tracks, failing in a brittle manner. The heat-treated EN-silicon carbide coatings, however, exhibited no cracking nor chipping, believed to be due to its higher fracture toughness than the other heat-treated coatings, attributable to its lower phosphorus content. The volume of material removed from the silicon carbide scratch track was 1/3 of the volume removed from the steel substrate at a 20 N load, and showed the best wear/ scratch resistance of any of the coatings tested.     

Adhesion of wear resistant hard coatings to steel substrates

The scratch-adhesion test has been used to monitor the coating-to-substrate adhesion of hard coatings deposited onto steels by two different techniques. In the first instance TiN, TiC and Al₂O₃ coatings were deposited by chemical vapour deposition (CVD). With the CVD TiC and Al₂O₃ coatings, pre-critical stylus load flaking could be observed at the edges of the scratch channel. In contrast, TiN did not display such flaking. Energy dispersive X-ray analysis (EDXA) and Auger electron spectroscopy (AES) were used to investigate this behaviour. In the second example, the initial stage of a continuous plasma nitride-TiN magnetron deposition process was varied to optimize the adhesion of the subsequently deposited TiN topcoat. A suite of characterization techniques including hardness determination, AES, profilometry, and optical cross-sectioning was used to help explain the scratch-adhesion test results.     

Wear Resistance of the La<Subscript>62</Subscript>Cu<Subscript>12</Subscript>Ni<Subscript>12</Subscript>Al<Subscript>14</Subscript> Bulk Metallic Glass Under Dry Friction Conditions

The wear properties of a La₆₂Cu₁₂Ni₁₂Al₁₄ bulk metallic glass (BMG) using sliding wear system under the various normal loads and the annealing conditions have been investigated. Although the La₆₂Cu₁₂Ni₁₂Al₁₄ BMG is brittle during the tensile testing, it exhibits ductile behaviors during the sliding wear process. The SEM and the EDS analyses of the wear tracks and the debris after the sliding wear processes indicate that the wear mechanism is a combination of abrasion, adhesion, and oxidation. It is found that the wear resistance is significantly affected by the normal loads. With the increases in the wear load, the wear loss and the friction coefficient decrease. In addition, it is found that the wear properties are significantly affected by the annealing conditions. Compared with the annealed BMG alloys, the as-cast BMG alloy with a low hardness exhibits good wear resistance, which is attributed to the better ductility during the wear testing.     

The study of the adhesion of a TiN coating on steel and titanium alloy substrates using a multi-mode scratch tester

A titanium nitride (TiN) coating was deposited by magnetron sputter ion plating onto steel and titanium alloy polished substrates. The adhesion of the coating on each substrate material was investigated using a newly developed multimode scratch tester. Progressive loading scratch tests, constant load scratch tests, multiple scratch tests in the same track and indentation tests were all performed. It was shown that the modified scratch tester can be used to identify not only coating detachment during progressive load scratch tests, but also other failure events such as cracking and cohesive damage to the coatings. By using the additional modes of operation, it was possible to study the fracture mechanisms in more detail i.e. chipping in the scratch track was cohesive for the TiN coated steel and adhesive for the TiN coated Ti alloy.     

Abrasive and Adhesive Wear Behavior of Arc-Evaporated Al<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Cr<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>N Hard Coatings

During the last decade, the usage of difficult-to-machine materials such as austenitic stainless steels has increased continuously in various industrial applications. Tools such as blind hole taps, punches, or deep drawing molds are often exposed to severe wear while machining/forming these materials, mainly due to excessive adhesion and material transfer. On combination with abrasive wear due to work-hardened wear debris, tool lifetime in these applications is often limited. In this study, ball-on-disc experiments were carried out with arc-evaporated AlCrN coatings with different Al/(Al + Cr) ratios against Al₂O₃ and austenitic stainless steel balls in ambient atmosphere. Test temperatures of 25, 500, and 700°C were chosen for the hard Al₂O₃ balls simulating severe abrasive loads, whereas 25, 150, and 250°C were used for the softer stainless steel material to evaluate the adhesive wear behavior. Characterization of the wear tracks was done by scanning electron microscopy in combination with energy-dispersive X-ray analysis and optical profilometry. The best abrasive wear resistance during testing against Al₂O₃ was observed for the coating with the highest Al content. In the case of the austenitic stainless steel balls, sticking of the ball material to the coating surface was the dominating wear mechanism. The influence of test temperature, chemical composition, and surface roughness was studied in detail.     

High Wear Resistance of Magnetron Sputtered Cr<Subscript>80</Subscript>Si<Subscript>20</Subscript>N Nanocomposite Coatings: Almost Independent of Hardness

Hardness has been popularly considered as an essential factor defining the wear resistance of hard coatings. Here, we report magnetron sputtered Cr₈₀Si₂₀N nanocomposite coatings, of widely varied packing densities, that exhibited identical specific wear rates, while the hardness changed over a wide range (from ~12 to ~36 GPa). All the Cr₈₀Si₂₀N coatings were free of extended and uninterrupted columnar boundaries, and retained low specific wear rates in the ball-on-plate sliding tests against Al₂O₃ counterpart with a normal load of 5 N (less than 3.0?×?10^?16 m³/N m under ambient condition and less than 2.0?×?10^?15 m³/N m under 3.5 wt% NaCl solution, respectively). Post examination reveals extensive interruption or termination of cracks in the wear tracks of the under-dense coatings, indicative of extrinsic toughening mechanisms by effective relief of local contact stress. Our results suggest that a critical role of toughening rather than hardening, played in enhancing the wear resistance of hard coatings, and thus would pave a way to develop highly wear-resistant coatings with a low hardness.     

Influence of layer thickness on hardness and scratch resistance of Si-DLC/CrN coatings

Abstract

Multifunctional coatings, widely used in tribological applications, have their properties strongly influenced by the interaction of the system coating/substrate. The use of multilayered coatings has been pointed out as a solution for the problem of high internal stresses that can be generated in coated systems, in particular in the case of soft substrates. In multilayered coatings, a decrease in the stress gradient between substrate and coating improves adhesion. Moreover, the thickness of the coating has shown a strong influence on the tribological behaviour of the coated system. This paper, through widely used and efficient techniques, seeks to assess the influence of the thickness of different layers (DLC and CrN) on the response of a multifunctional coating. Si rich DLC and CrN coatings with different thicknesses were deposited on a steel substrate (AISI 1020) by Plasma Enhanced Magnetron Sputtering (PECVD). Scanning electron microscopy (SEM) and Raman spectroscopy (RS) were used in order to characterize the chemical composition and microstructure of the coatings. Instrumented indentation and scratch test techniques were used to measure hardness, elastic modulus, and adhesion of each layer. Critical loads were determined by visual analysis, using SEM in conjunction with the curves obtained in the scratch tests. The evaluation of the effect of the thicknesses of the layers allowed an optimised design of the multifunctional coated systems with improved durability.     

Effects of Surface Pretreatment of Ti-6AI-4V on the Adhesion and Wear Lifetimes of Sputtered MoS2 Coatings

Improving the adhesion and wear endurance lifetimes of the solid lubricant molybdenum disulfide (MoS₂) on titanium (Ti) alloys was studied in this experimental investigation. Ti-6Al-4V alloy specimens were implanted with gas ions or coated with ceramic layers prior to coating with sputtered MoS₂ to investigate the adhesion and wear lifetimes of the MoS₂ coatings. The greatest improvement in scratch adhesion (2.4 times Ti-6Al-4V coated directly with MoS₂) was observed for an MoS₂/diamond-like carbon/Si multilayer coating. Sliding wear tests revealed the greatest lifetime improvement (3.2 ×) was for an MoS₂/TiC dual-layer coating. Increased MoS₂ adhesion was observed for pretreated surfaces with a Vickers microhardness greater than 800 kgf/mm². Increased adhesion of MoS₂ for bond layers with lower elastic moduli (estimated) is suggested. Therefore the ratio hardness/elastic modulus may be a potential figure of merit for surface pretreatment selection.     

Experiences from scratch testing of tribological PVD coatings

The use of PVD coatings in tribological applications becomes more and more widespread. Thus also the need to fully understand the relationships between the intrinsic properties of the coating, the properties of the coating/substrate composite and the tribological performance of the composite in different tribological systems becomes increasingly pressing. One of the tools available for tribological characterization of coatings and coating/substrate composites is scratch testing. In the current paper, Uppsala University presents a selection of results from many years of scratch testing of PVD coated components. Applications range from adhesion assessment and coating quality determination to estimation of coating fracture resistance. Examples in the form of scratch studies of PVD coatings on various high speed steels and tool steels - including failure mode anaiysis in situ SEM - are given.     

Tribological Properties of Nanocomposite CrC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/a-C:H Thin Films

Recently we showed that coatings, prepared by unbalanced magnetron sputtering from a metallic Cr target in an Ar/CH₄ discharge are composed of nanocrystalline CrC _x embedded in an a-C:H matrix. This work investigates the structural correlation of such nanocomposite CrC _x /a-C:H coatings to their tribological properties. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize the phase composition and the chemical bonding in the films deposited at different experimental conditions. The coating microstructure was investigated on selected samples by high-resolution transmission electron microscopy. For CrC _x -dominated coatings deposited at CH₄ partial to total pressure ratios (p_CH4/p_t) < 0.42, only minor changes regarding the friction coefficients and the abrasive wear rates were observed although microstructural changes towards a higher degree of crystallinity were proven by transmission electron microscopy and substantiated with XPS results. For a-C:H dominated coatings deposited at p_CH4/p_t > 0.42, the friction coefficients and abrasive wear rates were shown to decrease with increasing a-C:H phase content and its more sp²-like bonding configuration. It can be concluded that the microstructural changes in terms of CrC _x crystallite coarsening and bonding configuration of the a-C:H matrix phase are responsible for the observed changes of the friction coefficients and wear rates.     

The Effect of Weathering on Tribological Properties of an Acrylic Melamine Automotive Nanocomposite

Acrylic/melamine clearcoats containing different loads of nano silica were artificially weathered by a xenotester, and their tribological properties after various exposure times were studied. Scratch resistances, in terms of gloss retention, of each weathered coating were assessed by a carwash simulator. Scanning electron and optical microscopes were utilized to observe damages caused by carwash brushes. Micro- and nano-indentation tests were carried out after accelerated weathering tests to investigate changes in hardness as well as viscoelastic properties of coatings. Result of this study showed that the scratch resistance of different coatings decreased during weathering at initial times of weathering, followed by a slight increase at later times of weathering. Initial decrease in scratch resistance was attributed to being roughened of the coatings’ surface which increases friction between carwash brushes and the coating surface. The increased scratch resistance at later times was assigned to increase in hardness and elastic recovery of the coatings. It was also found that incorporation of nanoparticles into acrylic melamine clearcoats led to the formation of ductile-type scratches.     

Tribological and mechanical investigation of SiO2 and Si3N4 coatings on fused silica and borosilicate glass

Amorphous SiO₂ and Si₃N₄ plasma‐enhanced chemical vapour deposited (PECVD) coatings were deposited on two different substrate materials (fused silica and borosilicate glass), with three coating thicknesses (0.1, 0.5, and 1.0 μm). The mechanical properties (hardness and elastic modulus) were determined by depth‐sensing indentation, with loads from 700 mN down to 0.1 mN. Tribological behaviour was studied in instrumented oscillating sliding tests at room temperature with a ball‐on‐flat arrangement, in which the coated disc was tested against an alumina ball, at a load of 1 N. Interpretation of the measurement of hardness and modulus of the coatings has to take into consideration the influence of layer thickness and the effect of the substrate. Tensile film stress and crack generation were only observed for Si₃N₄ on fused silica above a threshold thickness. Friction and wear measurements show that the coating has an effect on friction, while wear is affected by the thin coatings only for a short running‐in phase. The morphology of the wear scars indicates that the coatings have good adhesion. Despite crack generation, delamination effects were not observed. Indentation patterns similarly showed excellent lateral homogeneity of the mechanical properties over the entire film surface, and indicated that load‐displacement curves may be used to characterise the system.     

Microstructure,tribological and mechanical strengthening effect of multiphase Zn/ZrO<Subscript>2</Subscript>-SiC electrodeposited composite coatings

In an attempt to improve the mechanical and thermal resilient properties of mild steel, Zn-ZrO₂-SiC composite coating was fabricated from zinc-based sulphate electrolyte with incorporated composite particles of ZrO₂/SiC at 2.0 A/cm² for 10 min. The effects of particle on the mechanical properties were examined using scanning electron microscope attached with energy dispersion spectroscopy and atomic force microscopy. The micro-hardness and wear resistance behaviour were determined with high diamond micro-hardness tester and three body abrasive MTR-300 testers with dry sand rubber wheel apparatus with 5 N. The fabricated coating was thermally heated at 200 °C for 4 h to evaluate the coating stability. From the results, a modification in the microstructure and topographic orientation as a result of incorporated composite was noticed on the zinc matrix. The mechanical and thermal properties were observed to be considerably improved by the incorporation of the ZrO₂/SiC weight fraction. A significant improvement in wear and hardness properties were also obtained for the multiphase embedded coatings.     

Study of tribological properties of coating/substrate system in micrometer and nanometer scales with a scanning probe microscope

We have used a scanning probe microscope equipped with a custom made diamond tip to study tribological properties of an inorganic–organic hybrid Si, O, H, and C coating produced by plasma enhanced chemical vapor deposition (PECVD) on siloxane/acrylic/polycarbonate multilayer substrates and on glass substrates. The micro indentation hardness and micro mar resistance were measured under different normal forces, and the critical loads for cracking, delamination, and chipping were evaluated. The effects of substrate, coating thickness, and interfacial adhesion on tribological properties of the coating/substrate systems are discussed. The results show that increasing coating thickness and strengthening interfacial adhesion can effectively inhibit cracking, delamination, and chipping of the coating/substrate systems under wear. Improving the physical properties of the PECVD coating and substrate, such as enhancing elastic recovery, reducing plasticity and brittleness, and matching the properties of coating and substrate better can improve the wear resistance of the systems further.     

Tribological Behaviour of Nanostructured Al2O3-3 wt% TiO2 Coating Against Steel in Dry Sliding

Nanostructured and conventional Al₂O₃-3 wt% TiO₂ coatings were deposited by atmospheric plasma spraying. The wear and friction properties of both coatings against a steel ball under dry friction conditions were examined. It was found that the wear resistance of the nanostructured Al₂O₃-3 wt% TiO₂ coating was superior to that of the corresponding conventional counterpart. The improvement in wear resistance of the nanostructured coating was attributed to its higher toughness and cohesion strength between splats. As for the nanostructured coating, the wear mechanism was mainly adhesion with micro-abrasion at low loads (20 N). At high loads (80 N), the wear of the nanostructured coating was controlled by plastic deformation and associated delamination along the splat boundaries, which was similar to that of the conventional coating at low loads. However, the failure of the conventional coating was predominantly brittle fracture within the splats and delamination between splats at high loads.     

Tribological Properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/CuCrZr Composites

Al₂O₃ particles reinforced Cu–Cr–Zr alloy matrix composite was fabricated through a powder metallurgy plus hot extrusion process by using the water atomization Cu–Cr–Zr powder as raw material. The effect of aging treatment on the tribological behavior of the composite was investigated. Experimental results show that tiny coherent precipitated phases were formed in the matrix after proper aging treatment and therefore good combination properties could be obtained. The wear rates of the Al₂O₃/CuCrZr composite and its matrix alloy were obviously influenced by the aging treatment, wherein the best wear resistance was reached at the aging temperature corresponding to the highest Vickers hardness. The major reason was that the depth of plastic deformation in the subsurface region was dramatically decreased due to the improvement of mechanical properties of the matrix, and therefore adhesion induced surface materials loss could be markedly alleviated. By comparing with the SiC20 vol%/Cu composite, it is indicated that the Al₂O₃/CuCrZr composite exhibited much better wear resistance as well as higher electrical conductivity.     

Investigation of antiwear coatings deposited by the pvd process

The tribological properties of various PVD‐deposited coatings (vacuum arc method) have been tested, both single‐layer coatings (TiN, CrN, Ti(C,N), and Cr(C,N)) and multilayer coatings (Cr(C,N)/CrN/Cr and CR(C,N)/(CrN+Cr₂N)/CrN/Cr). An unlubricated ball‐on‐disc tribosystem was used in which an Al₂O₃ ball is pressed against a coated steel disc rotating in the horizontal plane. A novelty of the method is the removal of wear debris from the contact zone using a draught of dry argon. This improves the repeatability of the test results and the stability of the tribological characteristics. It is shown that CrN coatings exhibit the best antiwear properties and Ti(C,N) the worst. Multilayer coatings have better antiwear properties than single‐layer ones. The friction coefficients for CrN and Cr(C,N) coatings are much smaller than for the commonly used TiN. A correlation has also been found between the physical properties of the coatings tested (adhesion of the coating to the substrate assessed in scratch tests, and coating hardness) and their antiwear properties. An improvement in coating‐substrate adhesion results in wear reduction, while greater hardness (causing a coating embrittlement increase and a change in the wear mechanism) brings about greater wear. There is no correlation between the physical properties and the friction coefficients of the coatings tested.     

Scratch Behavior of ZrO<Subscript>2</Subscript> Thin Film Prepared by Atomic Layer Deposition Method on Silicon Wafer

To evaluate friction behaviour and adhesion strength of 130 nm-thick zirconia (ZrO₂) film produceded by atomic layer deposition (ALD) on Si substrate, scratch tests were performed at two different scales; micro- and macro-scales. Surface morphology, roughness, crack propagations and interations between the surface and sliding indenter were also investigated. Scratch test was also conducted with Si substrate as a reference. The test results showed that friction coefficient (COF) was influenced by the scale of scratch test regardless of the tested materials. In microscale test, the 130 nm-thick zirconia film failed at the critical load of 96 mN and direct relationship between the generation of micro-cracks and friction coefficient was observed. Based on the Hertzian contact theory and experimental results, the macroscratch width was much greater than that in microscratch test although the maximum contact pressure were comparable in both cases. Further discussion was made with regard to the influence of the contact pressure on COF, crack generation and film removal. Various types of failure mode were identified through analyzing the mechanical response of scratch tracks both at micro- and macroscale tests. This study suggested that 130 nm-thick ALD-ZrO₂ film showed better tribological and adhesion properties at microscale contact than macroscale contact.     

Sliding wear behaviour of ZrN and (Zr, 12 wt% Hf)N coatings

In the present study, the sliding wear resistances of ZrN and (Zr, 12 wt% Hf)N coatings deposited on a hardened AISI D2 tool steel by arc-physical vapor deposition (PVD) technique were examined by a ball-on-disc wear tester. Alloying of ZrN coating with 12 wt% Hf did not change the hardness significantly, but achieved an improvement on adhesion strength and dry sliding wear resistance against steel (AISI 52100-55HRC) and Al₂O₃ balls.     

Mechanical characterization of nanostructured TiB2 coatings using microscratch techniques

TiB₂-based nanostructured coatings were fabricated on high-speed steel by magnetron sputtering technique. Mechanical characterization of the resultant coating-substrate systems, such as coating adhesion, friction and scratch resistance, was conducted by microscratch technique. The linearly increasing load mode of microscratch test was studied to determine the most effective and informative testing conditions and to determine the critical load (Lc) for coating failure. The mode of failure was examined by high resolution SEM and AFM. In order to gain a better understanding of the scratch behaviour during the test, a three-dimensional finite element (FE) model was developed to simulate the scratch process. The developed FE model was able to demonstrate the elastic and plastic behaviour of the coating and substrate around the contact area during scratch test. Good agreement has been observed between the FE analysis results and experimental investigations.