Na2SO4沉积盐引起的Ni3Al—Fe的中温区热腐蚀

研究了Ｎａ２ＳＯ４沉积盐引起的Ｎｉ３Ａｌ－Ｆｅ于７００－８２０℃空气中的腐行为，结果表明，Ｎｉ３Ａｌ－Ｆｅ遭受自持性的热腐蚀，热腐蚀的发生似可归因于Ｆｅ与Ｎａ２ＳＯ４反应的产物Ｎａ２Ｏ与Ｎａ２ＳＯ４形成了Ｎａ２Ｏ－Ｎａ２ＳＯ４共晶熔融盐，随中金中Ｍｏ的氧化产物ＭｏＯ３参与电化学阴极还原反应，从而引发合金快速的热腐蚀，此外，熔盐中Ｎａ２ＳＯ４与ＭｏＯ３反应生成的ＳＯ３导致了熔盐的高酸度和合金的内硫化     

渗铝NiAl－20％Fe金属间合金的高温热腐蚀

本文研究了在９５０℃空气中，表面涂Ｎａ_２ＳＯ_４盐膜的条件下，ＮｉＡｌ，ＮｉＡｌ－２０％Ｆｅ及渗铝后的高温热腐蚀行为。在热腐蚀过程中，ＮｉＡｌ合金表面能形成Ａｌ_２Ｏ_３膜，显示出一定的耐蚀性能。但Ａｌ_２Ｏ_３膜易开裂，Ａｌ_２Ｏ_３膜的溶解及开裂会引发合金发生快速热腐蚀；２０％Ｆｅ的加入则使ＮｉＡｌ合金的耐蚀性能显著变差，合金表面不能形成单一的Ａｌ_２Ｏ_３膜；渗铝处理可以明显提高ＮｉＡｌ－２０％Ｆｅ合金的耐蚀性能，且渗铝涂层的耐蚀性能优于ＮｉＡｌ合金，这与铝化物涂层中的Ａｌ含量较高，Ａｌ_２Ｏ_３膜的开裂倾向较小有关。     

渗铝NiAl—20?金属间合金的高温热腐蚀

本文研究了在９５０℃空气中，表面涂Ｎａ２ＳＯ４盐膜的条件下，ＮｉＡｌ，ＮｉａＬ－２０％Ｆｅ及渗铝后的高温热腐蚀行为。在热腐蚀过程中，ＮｉＡｌ合金表面形成ＡｌＯ３膜，显示出一定的耐蚀性能。但Ａｌ２Ｏ３膜易开裂，Ａｌ２Ｏ３膜易开裂，Ａｌ２Ｏ３膜的溶解开裂会引发合工发生快速热腐蚀，２０％Ｆｅ的加入则使ＮｉＡｌ合金的耐蚀性能显著变差，合金表面不能形成单一的Ａｌ２Ｏ３膜；渗铝处理可以明显提高ＮｉＡｌ－２０＾     

ELECTROCHEMICAL IMPEDANCE OF HOT CORROSION OF SPUTTERED CoCrAlY COATING ON Ni_3Al And Ni_3Al－Fe INTERMETALLICS

采用电化学交流阻抗技术并结合物相分析技术研究了溅射ＣｏＣｒＡｌＹ涂层对Ｎｉ３Ａｌ、Ｎｉ３Ａｌ－Ｆｅ金属间化合物在７００℃熔融（Ｎａ，Ｌｉ，Ｋ）２ＳＯ４中腐蚀行为的影响．结果表明，Ｎｉ３Ａｌ和Ｎｉ３Ａｌ－Ｆｅ的耐熔融盐腐蚀性能较差，其交流阻抗Ｎｙｑｕｉｓｔ图高频端表现为一曲率半径很小的圆弧，低频端为一直线，腐蚀反应受氧化剂的扩散所控制；施加ＣｏＣｒＡｌＹ涂层后，Ｎｙｑｕｉｓｔ图则呈双容抗特征，发生了沿涂层缺陷的腐蚀；提出了交流阻抗模型并解析了其中的参数．     

Ni3Al材料在O2／SO2／SO3气氛中的低温热腐蚀行为

用涂盐法并借助扫描电镜、光谱分析、金相、电子探针及Ｘ射线衍射等技术研究了Ｎｉ３Ａｌ金属间化合物在Ｏ２／ＳＯ２／ＳＯ３气氛中６００－８００℃温度范围内（Ｎａ，Ｋ）２ＳＯ４引起的低温热腐蚀行为。结果表明，Ｎｉ３Ａｌ发生了低温热腐蚀，其腐蚀速度在７５０℃呈现一最大值。热腐蚀的发生主要归因于多元共晶盐的形成。盐沉积加速了材料在空气中的氧化。ＣｏＣｒＡｌＹ涂层能改善合金的耐蚀性能。     

含Mo的Ni_3Al－Fe基合金在900－1100℃空气中的氧化行为

研究了含Ｍｏ的Ｎｉ３Ａｌ－Ｆｅ基合金在９００－１１００℃空气中的等温氧化行为，利用光学显微镜、ＳＥＭ、ＥＰＭＡ、ＸＲＤ分析了氧化膜的形态和结构．研究表明，含Ｍｏ的Ｎｉ３Ａｌ－Ｆｅ基合金由γ和β相组成．对应于γ相的氧化膜由多相组成，合金元素Ｆｅ和Ｍｏ使得γ相的氧化速率增大，氧化膜的粘附性和内聚力下降，其氧化反应激活能为４２．７ｋＪ／ｍｏｌ，Ｆｅ穿过Ａｌ２Ｏ３氧化层的扩散为氧化反应的速率控制步骤．而β相中的Ｆｅ和Ｍｏ，对其抗氧化性无不利影响，氧化膜仅由Ａｌ２Ｏ３．     

Fe—Mn─Al合金的腐蚀性能与钝化膜的研究

应用阳极极化及ＡＥＳ／ＸＰＳ技术,研究了Ｆｅ－３０．８Ｍｎ－８．２Ａｌ奥氏体合金在ｐＨ值为－０．８至１５．３的水溶液中的腐蚀性能,并与Ｆｅ－３０Ｍｎ合金、低碳钢、９％Ｎｉ低温钢及１Ｃｒ１３不锈钢进行对比。在所测试的水溶液中,该合金的腐蚀抗力优于低碳钢和Ｆｅ－３０Ｍｎ合金,与９％Ｎｉ钢相当,但不及１Ｃｒ１３不锈钢。Ｆｅ－３０．８Ｍｎ－８．２Ａｌ合金在１ｍｏｌ／ＬＮａ２ＳＯ个中形成的钝化膜的最表层可能为氢氧化物,而膜的主体由Ｆｅ２Ｏ３、Ｍｎ２Ｏ３及Ａｌ２Ｏ３组成。     

含Mo的Ni3Al—Fe基合金在900—1100℃空气中的氧化行为

研究了含Ｍｏ的Ｎｉ３Ａｌ－Ｆ３基合金在９００－１１００℃空气中等温氧化行为，利用光学显微镜、ＳＥＭ、ＥＰＭＡ、ＸＲＤ分析了氧化膜的形态和结构。研究表明，含Ｍｏ的Ｎｉ３Ａｌ－Ｆ３基合金由γ和β相组成，对应于γ相的氧化膜由多相组成，合金元素Ｆｅ和Ｍｏ使得γ相的氧化速率增大，氧化膜的粘附性和内聚力下降，其氧化反应激活能为４２．７ＫＪ／ｍｏｌ，Ｆｅ穿过Ａｌ２Ｏ３氧化层的扩散为氧化反应的速率控制步骤。而β相     

定向凝固Ni_3Al－Mo基合金高温氧化研究SCIEI

利用热天平连续称重，研究了Ｎｉ３Ａｌ－Ｍｏ基合金（ＩＣ－６）在１２７３，１３７３Ｋ的空气中恒温３００ｈ的氧化行为．用ＥＰＭＡ及ＸＲＤ分析了氧化层的结构和成分，；ＩＣ－６合金的氧化层中包括ＮｉＡｌ２Ｏ４，ＮｉＭｏＯ４，ＭｏＯ２相．氧向内扩散及ＭｏＯ２氧化形成挥发性ＭｏＯ３同时影响着ＩＣ－６合金的氧化进程，氧化反应方程式可表示为：理论方程与实验数据吻合较好．ＭｏＯ３在１２７３、１３７３Ｋ的挥发速率常数分别为３．２７×１０－５和２．５５×１０－４ｍｇ／ｃｍ２·ｓ．     

Na_2SO_4沉积引起的Fe─10Cr合金在700℃的热腐蚀

研究了涂有Ｎａ２ＳＯ４盐膜的Ｆｅ－１０Ｃｒ合金在７００℃，Ｏ２－０．５％（ＳＯ２＋ＳＯ３）气氛中的热腐蚀行为。结果表明，该合金在实验条件下发生了“低温”热腐蚀。腐蚀产物分两层，即在熔盐中沉积出的疏松氧化物层和在合金表面直接成长的相对致密的氧化物层。腐蚀形貌观察说明，热腐蚀的发展主要伴随着致密氧化层的增厚。腐蚀动力学和腐蚀形貌特点支持热腐蚀的电化学机理模型。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.