基于推覆分析的RC框架地震倒塌易损性预测

基于倒塌率的结构倒塌易损性分析是目前评价结构抗倒塌能力最合理的方法.但是,目前基于增量动力分析(IDA)的倒塌率分析方法,工作量和实施难度大,很难直接用于工程设计,因此有必要研究便于工程应用的新方法.本文基于18个典型多层RC框架结构的IDA倒塌率分析和静力推覆分析,发现RC框架在大震下的倒塌率及抗倒塌安全储备(CMR)与静力推覆得到的结构位移安全储备之间存在较好的相关关系.依据此关系,建议了保证大震倒塌率的推覆位移安全储备,并通过9个RC框架结构算例进行了验证.本文方法简单易行,可供规则多层RC框架结构抗倒塌设计参考.     

基于性能的基础隔震钢筋混凝土框剪结构的倒塌可靠度分析

利用基于性能的结构可靠度分析方法,对基础隔震钢筋混凝土框剪结构进行分析研究。选取20条实际地震动记录,以0.2g为步长对结构地震动参数PGA进行调幅后,建立了140个结构-地震动样本空间。选取上部结构的最大层间位移角、隔震层位移为量化指标,对每一个样本进行动力非线性时程分析后,将结构响应进行统计得到结构在各地震动强度下超越极限破坏状态的概率,将其绘制成基础隔震钢筋混凝土框剪结构的易损性曲线并利用整体可靠度方法分析结构发生倒塌的可靠度指标。该方法直观地反映了结构发生倒塌的概率,为结构的地震损失评估提供依据。     

多维地震作用下钢筋混凝土建筑结构的抗连续倒塌仿真分析

为了提高钢筋混凝土建筑结构的抗震性能,分析多维地震作用下钢筋混凝土建筑结构的抗连续倒塌能力,结合钢筋混凝土建筑结构特性、节点构造特点以及其在多维地震作用下的破坏机理,采用离散单元法建立结构连续倒塌的理论模型,对建筑结构连续倒塌过程进行数值模拟。基于数值模拟化结果,通过备用荷载路径法,实现建筑结构的抗连续倒塌分析。仿真实验结果得出,所提方法能实现对建筑结构抗连续倒塌的准确分析,且在多维地震作用下建筑结构扭转的幅度明显变大,结构顶层位移发散状态显著,不同楼层会产生不同的层间位移以及薄弱部位,建筑结构的抗连续倒塌性能随着失效构件位置的提升而增强。     

基于耐震时程法的钢筋混凝土框架弹塑性地震响应及损伤发展

耐震时程法（ETA）仅需少量的非线性时程分析,便可以掌握结构倒塌破坏的全过程。但是,此方法目前较少应用于结构倒塌失效分析。本文探讨了耐震时程曲线的特性及拟合思路,以钢筋混凝土框架为研究对象,应用ETA方法分析了钢筋混凝土框架的地震响应及损伤发展。研究结果:（1）混凝土框架结构的地震响应分析结果表明:采用ETA方法分析时结构顶点位移和层间位移角与采用IDA方法分析时接近,而最大基底剪力会略大;但是,两种方法的结果相关系数均接近于1。（2）强震下的结构倒塌分析结果表明:ETA方法能较为准确的预测结构的塑性铰分布、塑性铰出现概率及塑性铰发展顺序。当采用多条耐震时程加速度曲线作为输入时,评估结果准确性更高。由于ETA方法仅需进行少量几条耐震时程分析且计算高效,因此ETA方法可以成为预测结构失效模式的高效方法。     

高层分段隔震结构的动力响应分析

本文提出了一种基于叠层橡胶支座的大高宽比高层建筑分段隔震结构形式,并对同一高层建筑结构分别采用基础隔震、层间隔震和分段隔震三种不同形式时进行了数值模拟对比分析。结果表明,采用分段隔震形式可明显减小高层建筑结构的顶层侧向位移、中间隔震层的相对位移和下支柱端应力,使结构的侧向位移集中于两个隔震层上,耗散了大部分地震输入能量,保障了与隔震层相连的构件的安全性,防止了由于支座受拉或剪压破坏导致上部结构倾覆倒塌现象的发生。     

基于向量式有限元的黏滞阻尼减震结构抗竖向连续倒塌动力反应分析

向量式有限元是以向量力学为基础的一种新的结构分析方法,在处理结构大变形等复杂行为时具有较大的优势。基于向量式有限元理论建立了黏滞阻尼单元,对附加黏滞阻尼器的平面钢框架结构进行了抗竖向连续倒塌动力分析,结合拆除构件法,采用MATLAB编制可以考虑初始变形的瞬时卸载法程序,实现结构在构件拆除前的静力分析和构件拆除后动力分析的全过程统一。研究了阻尼器布置位置和参数在结构抗竖向连续倒塌中的性能需求,以失效点竖向位移时程曲线、梁端转角、动力放大系数和结构塑性铰分布为参考指标,对比分析布置阻尼器前后钢框架结构的抗连续倒塌能力。结果表明向量式有限元是一种研究结构竖向连续倒塌动力响应的有效方法,合理布置阻尼器能够有效控制剩余结构的变形和振动,降低构件内力,减少塑性铰个数,较大地提高结构的抗竖向连续倒塌能力。     

脉冲地震下简支梁桥倒塌过程及响应分析

为了模拟脉冲地震作用下简支梁桥的倒塌过程，基于LS-DYNA平台建立了简支梁桥的三维有限元模型，并人工合成了不同脉冲幅值和脉冲周期的地震动，研究了脉冲幅值和脉冲周期对简支梁桥倒塌过程和地震响应的影响，总结了地震作用下简支梁桥的灾变过程。研究表明：脉冲幅值对简支梁桥的倒塌模式影响显著，脉冲幅值较小时桥墩发生倒塌，脉冲幅值较大则会导致梁体落梁；脉冲幅值对桥梁位移响应影响较小，对内力响应和碰撞效应影响较大，增大脉冲幅值会加重梁间的碰撞效应，从而消耗大量地震能量；位移响应随脉冲周期的增大而增大，梁间碰撞力则与之相反；桥梁开始出现损伤的时间点与脉冲周期的大小有关，脉冲周期越小，开始出现损伤的时间越靠近地震加速度峰值时刻；脉冲地震作用下简支梁桥的倒塌表现为三个阶段：分别为正常运行阶段、损伤演变阶段和倒塌阶段。     

某新型梁柱节点的装配式钢筋混凝土框架结构基于性能的抗震设计研究

在一种新型无黏结预应力装配式混凝土梁柱框架节点抗震性能试验基础之上，使用基于位移的抗震设计方法对新型框架节点的无黏结预应力装配式钢筋混凝土框架结构进行整体抗震设计研究。首先使用有限元软件sap2000进行预应力三维结构设计并建立相应的有限元模型，同时建立该梁柱节点的梁恢复力模型，进而实现自定义塑性铰本构关系研究该装配式框架结构。使用pushover分析去表征结构的抗震性能，对比研究不同目标位移下的相应性能水平要求。通过施加Y方向均匀分布荷载对结构进行弹塑性推覆分析，对结构的层间位移角、破坏机制进行分析讨论。结果表明：按照"功能良好""生命安全""防止倒塌"三水平的设计均达到预期结果，各层层间位移角和薄弱层的性能均能满足规范的相应要求。并选用三条地震波对结构进行弹塑性动力时程分析，表明基于该新型梁柱节点的装配式结构在基于位移的抗震设计中可以较好满足相关抗震性能水平要求。     

基于IDA的层间隔震结构失效模式研究

层间隔震结构是由基础隔震结构发展而来的一种新型隔震结构。为研究层间隔震结构的倒塌,需先研究不同层间隔震结构的不同失效模式和失效位置,文章建立了3个不同结构参数的层间隔震结构有限元模型,选取20条与抗震规范反应谱吻合的地震动,采用增量动力分析（IDA）方法,分别对其失效模式和失效位置进行研究。研究表明:基于不同的结构参数,层间隔震的基本失效模式有三种,即隔震层水平位移超限导致结构失效、下部结构层间位移角超限导致结构失效、隔震层拉压应力超限导致结构失效;隔震层下部结构和隔震层最外边缘支座为结构的薄弱位置,应引起更多关注。此方法不仅可以研究结构的不同失效模式,还可以确定失效位置,可为下一步层间隔震结构的抗倒塌分析提供理论基础。     

多层建筑考虑低周疲劳特性的地震倒塌反应分析

本文建立了基于低周疲劳试验的抗震结构倒塌指标。通过１８，０００多个倒塌反应算例，分析了结构例塌反应的影响因素。运用正交设计和方差分析方法，得到了这些影响因素的显著性水平和显著性顺序。根据分析结果，将结构划分为强结构、中强结构和强结构三种类型，并提出了相应的倒塌验算方法。     

砂土地震液化后大位移室内试验研究探讨

砂土地震液化引起的地面大位移会对结构产生灾难性的破坏，这已引起了人们的重视，但对其进行研究时间较短。作者在大量阅读有关资料的基础上，详细介绍了液化后地面大位移研究的室内试验设备、试验方法、试样的制备、试验的主要规律及国内的研究现状，并对试验技术和结果进行了探讨，指出以室内试验为基础提出液化后的本构模型及实用计算方法是今后工作的重点。     

A parametric study of the required seating length for bridge decks during earthquake

During the recent major earthquakes, some bridges suffered severe damage due to the pull-off-and-drop collapse of their decks. This is due to the large differential movements of the adjacent spans of bridges during strong shaking compared to the seating lengths provided. The differential movements are primarily due to the different vibration properties of adjacent spans and non-uniform ground excitations at the bridge supports. This paper analyses the effects of various bridge and ground motion parameters on the required seating lengths for bridge decks to prevent the pull-off-and-drop collapse. The random vibration method is used in the analysis. A two-span bridge model with different span lengths and vibration frequencies and subjected to various spatially varying ground excitations is analysed. Non-uniform spatial ground motions are modelled by the filtered Tajimi–Kanai power spectral density function and an empirical coherency function. Ground motions with different intensities, different cross-correlations and different site conditions are considered in the study. The required seating lengths for bridge decks are calculated. Numerical results are presented and discussed with respect to different bridge vibration and ground motion properties. © 1998 John Wiley & Sons, Ltd.     

砂土液化引起大位移对地下管道影响的非线性分析

地下管线是生命线工程的主要部分,已经成为现代工农业生产和城镇生活的大动脉。已有震害调查表明,饱和砂土液化引起的地基大变形(侧向变形和沉降)是导致强震区生命线工程震害的主要原因。采用三维非线性有限差分分析方法来研究砂土液化引起的大位移对地下管道的破坏特征,分析砂土液化的斜坡变形特征、孔隙水的演化过程。结果表明,砂土液化引起的大位移对地下管道有破坏作用,导致管道变形规律与其斜坡的位移规律相同,地下管线的变形随着振动频率和幅值的增加其非线性增大。     

A design procedure for tied braced frames

The paper deals with the analysis of the seismic behaviour and design of tied braced frames (TBFs). The behavioural properties of TBFs are described and a comparison drawn with standard eccentrically braced frames. A design procedure is then proposed that aims to achieve optimal collapse seismic behaviour, i.e. a global collapse mechanism characterized by uniform plastic rotations of links. The procedure is based on the displacement‐based approach so as to achieve direct and efficient control of the peak ground acceleration of collapse. Applications are carried out on systems with different numbers of storeys and lengths of links to obtain confirmation of the accuracy of the design hypotheses and methodologies. Copyright © 2007 John Wiley & Sons, Ltd.     

THE DISPLACEMENT AND STRESS FIELD GENERATED BY THE COLLAPSE IN PINGYI COUNTY,SHANGDONG PROVINCE,ON DECEMBER 25, 2015

A collapse happened in Pingyi County, Shandong Province, on December 25, 2015. The displacement field, stress field and Coulomb failure stress change on the Mengshan frontal fault generated by the collapse are calculated by using point collapse model in isotropic medium. The result shows that: (1) The maximum horizontal displacement is located at the center of the collapse with value of~18mm. The horizontal displacements are greater than 1mm within~5km of the collapse with its direction pointing to the collapse center. The maximum subsidence is located at the center of the collapse with the value of 4mm. The subsidence is greater than 1mm within ~3km of the collapse. The displacement field decays so rapidly that can be ignored at far away from the collapse for the shallow source, which caused local displacement field. (2) Influenced by the free surface, the contraction area stress within ~5km of the collapse with the order of 1000Pa and expansion area stress in farther away areas at depth of 2km are estimated. the expansion area stress of 1000Pa is estimated at the~5km from the collapse center. Then the expansion area stress decays to 100Pa at the distance of ~10km from the collapse. The maximum compressive and extensional principal stresses are estimated as 10000Pa at the depth of 2km. The compressive stress axes present radical direction pointing to the collapse within ~5km of the center. In farther away from the collapse, The extensional principal stress axes present radical direction pointing to the center of the collapse. With farther distance to the collapse, the compressive and extensional stress decay rapidly to the order of 100Pa. (3) The Coulomb failure stress on the northwestern part of the Mengshan frontal fault, which is known as active segment of the Mengshan frontal fault, is decreased by the collapse with maximum value of 2500Pa. Whereas, the Coulomb failure stress on the southeastern part of the Mengshan frontal fault, which is known as left-lateral normal slip fault segment in Quaternary period, is increased by the collapse with maximum of 2400Pa, to which attention would be paid in seismic hazard analysis.     

Effect of ground motion selection methods on seismic collapse fragility of RC frame buildings

Variation in the seismic collapse fragility of reinforced concrete frame buildings predicted using different ground motion (GM) selection methods is investigated in this paper. To simulate the structural collapse, a fiber‐element modelling approach with path‐dependent cyclic nonlinear material models that account for concrete confinement and crushing, reinforcement buckling as well as low cycle fatigue is used. The adopted fiber analysis approach has been found to reliably predict the loss in vertical load carrying capacity of structural components in addition to the sidesway mode of collapse due to destabilizing P–Δ moments at large inelastic deflections. Multiple stripe analysis is performed by conducting response history analyses at various hazard levels to generate the collapse fragility curves. To select GMs at various hazard levels, two alternatives of uniform hazard spectrum (UHS), conditional mean spectrum (CMS) and generalized conditional intensity measure (GCIM) are used. Collapse analyses are repeated based on structural periods corresponding to initial un‐cracked stiffness and cracked stiffness of the frame members. A return period‐based intensity measure is then introduced and applied in estimating collapse fragility of frame buildings. In line with the results of previous research, it is shown that the choice of structural period significantly affects the collapse fragility predictions. Among the GM selection methods used in this study, GCIM and CMS methods predict similar collapse fragilities for the case study building investigated herein, and UHS provides the most conservative prediction of the collapse capacity, with approximately 40% smaller median collapse capacity compared to the CMS method. The results confirm that collapse probability prediction of buildings using UHS offers a higher level of conservatism in comparison to the other selection methods. Copyright © 2017 John Wiley & Sons, Ltd.     

公共建筑结构的抗地震倒塌能力优化评估分析

以往基于模态增量动力方法对公共建筑进行抗地震倒塌能力评估时是单纯地从总体角度进行考察的,其得到的结果较为粗糙,无法准确反映出公共建筑的抗地震倒塌能力,导致其经济效益较差。提出新的公共建筑结构抗地震倒塌能力优化评估方法以分析公共建筑整体的抗地震倒塌能力,总结出其与子结构以及构件三者间的关系,进而研究构件的损毁情况,以实现对建筑抗地震倒塌能力的整体评估。基于公共建筑的倒塌破坏区间,采用其结构抗震倒塌能力评估方法,对公共建筑结构的抗地震倒塌能力实施优化评估分析,得到其具体破坏指数,实现对其进行准确评估。实验结果说明,所提方法可准确描述公共建筑结构的抗地震倒塌能力,提高建筑结构抗地震倒塌能力和经济效益。     

大坝抗震安全性研究进展

论证了广大坝抗震安全性研究的实践与发展现状。目前大坝在地震作用下的应力与变形分析方法主要有拟静力法和动力响应分析法,并依据大坝混凝土的抗拉强度判断大坝的安全性;各国规范体现的抗震设防弹念和大坝材料的容许应力差别很大。坝址河谷不同高程处地震动状态不尽相同、河谷两恻同一高程处地震动也不一样。混凝土材料的强度与加载速度、应变速率有关;地震时大坝不同部位的应变速率不相同、同一部位的应变速率也随时间变化;混凝土的动态强度既与应变速率有关。也与应变历史等其它因素有关。大坝河谷地震动的输入机理和模型研究、混凝土的动态强度的变化规律探索、大坝抗震安全性评价准则的完善与创新等将有待深入。通过以上内容针对性分析,提出了大坝抗震评价的一些合理建议、方法以及进一步的研究方向。     

The effect of near-fault directivity on building seismic collapse risk

Forward directivity may cause large velocity pulses in ground motion time histories that are damaging to buildings at sites close to faults, potentially increasing seismic collapse risk. This study quantifies the effects of forward directivity on collapse risk through incremental dynamic analysis of building simulation models that are capable of capturing the key aspects of strength and stiffness degradation associated with structural collapse. The paper also describes a method for incorporating the effects of near-fault directivity in probabilistic assessment of seismic collapse risk. The analysis is based on a suite of RC frame models that represent both past and present building code provisions, subjected to a database of near-fault, pulse-like ground motions with varying pulse periods. Results show that the predicted collapse capacity is strongly influenced by variations in pulse period and building ductility; pulse periods that are longer than the first-mode elastic building period tend to be the most damaging. A detailed assessment of seismic collapse risk shows that the predicted probability of collapse in 50 years for modern concrete buildings at a representative near-fault site is approximately 6%, which is significantly higher than the 1% probability in the far-field region targeted by current seismic design maps in the US. Copyright © 2012 John Wiley & Sons, Ltd.     

Experimental multi‐level seismic performance assessment of 3D RC frame designed for damage avoidance

This paper experimentally investigates the application of damage avoidance design (DAD) philosophy to moment‐resisting frames with particular emphasis on detailing of rocking interfaces. An 80% scale three‐dimensional rocking beam–column joint sub‐assembly designed and detailed based on damage avoidance principles is constructed and tested. Incremental dynamic analysis is used for selecting ground motion records to be applied to the sub‐assembly for conducting a multi‐level seismic performance assessment (MSPA). Analyses are conducted to obtain displacement demands due to the selected near‐ and medium‐field ground motions that represent different levels of seismic hazard. Thus, predicted displacement time histories are applied to the sub‐assembly for conducting quasi‐earthquake displacement tests. The sub‐assembly performed well reaching drifts up to 4.7% with only minor spalling occurring at rocking beam interfaces and minor flexural cracks in beams. Yielding of post‐tensioning threaded bars occurred, but the sub‐assembly did not collapse. The externally attached energy dissipators provided large hysteretic dissipation during large drift cycles. The sub‐assembly satisfied all three seismic performance requirements, thereby verifying the superior performance of the DAD philosophy. Copyright © 2007 John Wiley & Sons, Ltd.