共查询到20条相似文献,搜索用时 62 毫秒
1.
4053160Y滚子外径面产生磁痕的原因分析 总被引:1,自引:0,他引:1
针对4053160Y滚子粗磨后磁粉探伤时,外径面出现比例较大的磁痕分布,对滚子外观、金相组织、硬度、宏观断口进行了检查,并用扫描电镜和能谱仪对断口进行观察和分析,得出:滚子心部存在大量轴向呈线状分布的氧化铝夹杂,以及细小裂纹等严重材料缺陷,导致在热处理过程中产生淬火裂纹。 相似文献
2.
对Φ20.2 mm GCr15球化退火磨光直条料采用单工位压力机开式下料、冷镦为圆锥滚子时大端产生裂纹的现象进行了分析。结果表明,该类裂纹是在开式下料时,料段的切面断口部位产生严重的剪切唇口、塌角、微裂纹等缺陷,在滚子冷镦成形时,由于该缺陷的缺口效应而使滚子大端产生裂纹。 相似文献
3.
1 2 2 32 8滚子裂纹形貌我厂生产的 2 2 32 8滚子在淬、回火后发现了淬火裂纹 ,平面磨后经磁力探伤挑出的裂纹滚子占 31 .5 %。1 .1 裂纹的宏观形貌裂纹有纵向、横向和扭曲形三种形式。纵向裂纹通过纵轴中心线平面完全贯穿或底部少部分连接 ,此种滚子一经磕碰就可分成两瓣。横向裂纹垂直于纵轴线的平面贯穿心部裂透 ,横向裂纹有的完全沿车加工刀痕分布 ,有的则越过刀痕。扭曲形裂纹是由纵向裂纹过渡到横向裂纹 ,也完全贯穿。裂纹的外观形貌如图 1所示。1 .2 裂纹方式其裂纹方式基本上属于纵劈和横断。其特点是 :开裂首先在纵、横截面的… 相似文献
4.
5.
采用磁粉探伤、冷酸洗及金相检验等方法对铁路客车轴承滚子的表面裂纹进行分析,结果表明,滚子制造过程中产生的二次淬火烧伤是造成滚子滚动面开裂的主要原因。通过采取减小滚子端面磨加工余量、增加外径磨削余量以及加强对套筒管理等措施,消除了二次淬火导致的烧伤。 相似文献
6.
7.
8.
9.
10.
11.
12.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
13.
根据广州市珠江新城旅客自动运输系统(APM)列车的运行特点,介绍APM列车制动系统的制动方式及其特点,分析APM列车动态制动和摩擦制动的工作机理及其区别和联系,阐明APM列车制动系统的电控制过程和气控制过程,从而为APM列车制动系统的维护和管理提供一定的依据. 相似文献
14.
我公司于80年代末引进Aspera公司年产80万台冰箱(冷柜)压缩机生产线及软件技术,在压缩机加工中,活塞销孔(如图1所示)的加工是难点之一。用镗床加工,质量一直难以达到要求,废品率很高。后来我们将Aspera公司的加工工艺即精镗后滚光改为精镗后用金刚石铰刀粗、精铰孔,由此解决了这个技术难题。(1)原意大利Aspera公司工艺简述其工艺流程为:钻6.5通孔→扩孔至7+0.1→粗镗7.473+0.036、圆柱度0.01→精镗至7.935+0.006、圆柱度0.002→滚光7.938+0.006、圆柱度0… 相似文献
15.
三爪自定心卡盘作为机床的主要附件,已有一百多年的发展历史,尽管目前随着数控技术的不断发展,越来越多地需求高速动力卡盘,但三爪自定心卡盘目前仍有一定的市场。 要保证卡盘可靠地夹紧工件,必须使其有可靠的夹持精度;要保持卡盘的精度,必须要严格控制各零部件公差及误差,如盘丝的极心偏。 极心偏是形成圆的渐开线的基圆圆心 (极心 )与盘丝内孔中心不同心所造成的偏差值。它对卡盘精度的影响分两种情况,一是卡爪夹持弧采用配磨,二是卡爪夹持弧采用单磨。本文主要探讨配磨时的影响。 卡爪夹持弧采用配磨,即每台卡盘整体… 相似文献
16.
详细分析了圆柱面素线的直线度公差带在新旧标准中定义和解释的区别,并从对圆柱面素线实际要素检测的角度,提出了推行新标准的实际意义。 相似文献
17.
18.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
19.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
20.
The article presents a brief review of the wear models based on the kinetic thermofluctuation approach. The materials were developed using SamGTU sclerometric programming software and a set of instruments developed at Samara Engineering University for assessing the parameters of kinetic thermoactivation for surface fracture deformed by friction. The first obtained results of assessments and the estimated prediction of wear resistance exemplified by tribocouple of the aircraft chassis are presented. 相似文献