Characteristics of probe electrospray generated from a solid needle

Probe electrospray ionization (PESI) has recently been developed, in which the electrospray was generated from a solid needle instead of by using a capillary. In this paper, the characteristics of probe electrospray ionization were studied based on the measurement of spray current, optical microscopy, and PESI mass spectrometry. In the experiment, the solid needle was moved up and down a vertical axis, and a small amount of sample was repeatedly loaded to the needle when the tip of the needle touched the surface of the liquid sample at the lowest position. After the application of high voltage, a liquid droplet was formed on the tip of the solid needle probe, with its size was determined by the size of the needle tip. The liquid flow rate to the tip, as indicated by the spray current, depends on the voltage applied to the needle as well as the loaded liquid amount. Stable electrospray can be maintained until the total consumption of liquid sample. The kilohertz current pulsation takes place in the case of overloading the sample to the needle. The influences of the applied voltage and the liquid flow rate on the PESI mass spectra were also examined.     

Development of sheath‐flow probe electrospray ionization (SF‐PESI)

Probe electrospray ionization (PESI) uses a sharp solid needle as electrospray emitter. This method was found to be applicable to the analysis of real‐world samples with high concentrations of salts and detergents without sample pretreatment. Since PESI is only applicable to wet samples but not to dry samples, sheath‐flow PESI (SF‐PESI) has been developed. The metal needle was inserted into the fine plastic capillary with a protrusion of 0.1–0.2 mm from the capillary terminus. The solvent was supplied continuously through the capillary. At the lowest position of the probe, solvent flowing out from the capillary makes the sample wet and extracts the analytes from the surface. The extracted analytes were electrosprayed at the highest position of the needle. SF‐PESI was successfully applied to samples such as narcotics, tablets, bill, fruits, potatoes, etc. Copyright © 2013 John Wiley & Sons, Ltd.     

Real‐time reaction monitoring by probe electrospray ionization mass spectrometry

Probe electrospray ionization (PESI) is a modified version of the electrospray ionization (ESI), where the capillary for sampling and spraying is replaced by a solid needle. High tolerance to salts and direct ambient sampling are major advantages of PESI compared with conventional ESI. In this study, PESI‐MS was used to monitor some biological and chemical reactions in real‐time, such as acid‐induced protein denaturation, hydrogen/deuterium exchange (HDX) of peptides, and Schiff base formation. By using PESI‐MS, time‐resolved mass spectra and ion chromatograms can be obtained reproducibly. Real‐time PESI‐MS monitoring can give direct and detailed information on each chemical species taking part in reactions, and this is valuable for a better understanding of the whole reaction process and for the optimization of reaction parameters. PESI‐MS can be considered as a potential tool for real‐time reaction monitoring due to its simplicity in instrumental setup, direct sampling with minimum sample preparation and low sample consumption. Copyright © 2010 John Wiley & Sons, Ltd.     

Application of probe electrospray to direct ambient analysis of biological samples

Recently, we have developed probe electrospray ionization (PESI) that uses a solid needle. In this system, the probe needle moves up and down along the vertical axis by a motor-driven system. At the highest position of the probe needle, electrospray is generated by applying a high voltage. In this study, we applied PESI directly to biological samples such as urine, mouse brain, mouse liver, salmon egg, and fruits (orange, banana, etc.). Strong ion signals for almost all the samples were obtained. The amount of liquid sample picked up by the needle is as small as pL or less, making PESI a promising non-invasive technique for detecting biomolecules in living systems such as cells. Therefore, PESI may be useful as a versatile and ready-to-use semi-online analytical tool in the fields of medicine, pharmaceuticals, agriculture, food science, etc.     

Physical properties of the probe electrospray ionization (PESI) needle applied to the biological samples

Probe electrospray ionization (PESI) is a recently developed technique that uses a fine solid needle as a probe for sampling biological materials. In this study, we quantified the volume of liquid sample picked up by the solid needle with the tip diameter of ～700 nm and the apex angle of ～60°. The amounts of low‐viscosity samples (rat urine) loaded on the tip of the needle by a single stroke were 0.35 ± 0.09 pl. Interestingly, the amount of liquid adhered to the tip did not significantly depend on the protein concentration, but viscosity and surface tension of the sample. Under these conditions, we successfully obtained mass spectra for each biological sample. Copyright © 2009 John Wiley & Sons, Ltd.     

Probe electrospray ionization of mixture solutions using metal needles with different tip conditions

Time-dependent mass spectra of mixture solutions of cytochrome c and cholesterol were measured by probe electrospray ionization (PESI) mass spectrometry and the PESI characteristics for several metal needles were investigated with different tip conditions. For a mixture solution of cytochrome c and cholesterol in 0.1% formic acid methanol/water (1/1) at a motion frequency of 1 Hz, an acupuncture needle with a sharp tip and 0.5-mm-diameter titanium and stainless-steel wire needles gave strong cytochrome c and extremely weak cholesterol ion signals. When the frequency was lowered, and the high-voltage duration increased, the titanium and stainless-steel needles provided both cytochrome c and cholesterol ion signals with high intensities well separated over time.     

Laser spray: electric field-assisted matrix-assisted laser desorption/ionization

A new liquid chromatography/mass spectrometry interface, the laser spray, has been developed. Explosive vaporization and mist formation occur when an aqueous solution effusing out from the tip of the stainless-steel capillary is irradiated from the opposite side of the capillary by a 10.6 microm infrared laser. Weak ion signals could be detected when the plume was sampled through the ion sampling orifice. When a high voltage (3-4 kV) was applied to the stainless-steel capillary, strong ion signals appeared. The ion abundances were found to be orders of magnitude greater than those obtained by conventional electrospray ionization in the case of aqueous solutions. The present method is regarded as an electric-field assisted form of matrix-assisted laser desorption/ionization in which the liquid chromatographic solvent (water, etc.) acts as a liquid matrix. Laser spray ionization is expected to become a versatile method for biological mass spectrometry because this method is compatible with the natural solvent, water.     

Sequential and Exhaustive Ionization of Analytes with Different Surface Activity by Probe Electrospray Ionization

The probe electrospray ionization (PESI) is an ESI-based ionization technique that generates electrospray from the tip of a solid metal needle. In this work, mass spectra for the single-shot PESI were measured as a function of time for a mixture of several analytes with different surface activity values. It was found that the analytes were elecrosprayed in the order of their surface activity. For example, detergent and protein were detected separately and respectively at the first and last stages of electrospray, for a mixed sample of 10^–3 M Triton X100 and 10^–5 M cytochrome c. For human breast cancer tissue, at first proteins such as α and β chains of hemoglobin, were observed as the dominant ions, but just before the liquid droplet on the needle was depleted only lipids were observed, meaning that PESI has the advantage of the suppression effect with analytes being detected separately in the order of their surface activity values.     

Performance of a sheathless porous tip sprayer for capillary electrophoresis-electrospray ionization-mass spectrometry of intact proteins

The performance of a prototype porous tip sprayer for sheathless capillary electrophoresis-mass spectrometry (CE-MS) of intact proteins was studied. Capillaries with a porous tip were inserted in a stainless steel needle filled with static conductive liquid and installed in a conventional electrospray ionization (ESI) source. Using a BGE of 100 mM acetic acid (pH 3.1) and a positively charged capillary coating, a highly reproducible and efficient separation of four model proteins (insulin, carbonic anhydrase II, ribonuclease A and lysozyme) was obtained. The protein mass spectra were of good quality allowing reliable mass determination of the proteins and some of their impurities. Sheath-liquid CE-MS using the same porous tip capillary and an isopropanol-water-acetic acid sheath liquid showed slightly lower to similar analyte responses. However, as noise levels increased with sheath-liquid CE-MS, detection limits were improved by a factor 6.5-20 with sheathless CE-MS. The analyte response in sheathless CE-MS could be enhanced using a nanoESI source and adding 5% isopropanol to the BGE, leading to improved detection limits by 50-fold to 140-fold as compared to sheath liquid interfacing using the same capillary - equivalent to sub-nM detection limits for three out of four proteins. Clearly, the sheathless porous tip sprayer provides high sensitivity CE-MS of intact proteins.     

基于敞开式直接电离质谱技术的尿液中毒品检测北大核心CSCD

尿液作为一种易于获取的体内毒品检材,在吸毒人员快速筛查中被广泛应用。针对传统快速筛查技术存在假阳性率高、定量能力不足以及实验室质谱技术在快速检测中存在前处理复杂、检测耗时长、使用环境苛刻等问题,该文提出了一种基于敞开式直接电离质谱技术的生物样本快速检测方法。该研究采用探针式电喷雾离子源与便携式质谱仪联用快速检测平台,优化了喷雾电压和质谱入口毛细管温度,开发了高效快速的前处理技术。基于该平台和前处理技术,5种常规毒品(甲基苯丙胺、氯胺酮、可卡因、O^(6)-单乙酰吗啡和3,4-亚甲双氧甲基苯丙胺)的尿液加标溶液的检出限为0.5~30 ng/mL,且其中4种毒品定量检测的线性相关系数大于0.99。除此之外,5种常规毒品在3个不同水平下的加标回收率为56.1%~103.7%,多次检测结果的相对标准偏差为9.0%~27.8%,说明联用检测平台与前处理方法结合可以达到良好的准确度。为了进一步检验该联用仪器的实战能力,测试了某社区戒毒康复中心40份阳性和110份阴性实际尿液样本,总体检测的准确率接近99%,且通过一次进样在20 s内可同时检测多种毒品。该研究成果有利于推动快速检测技术的发展,促进敞开式直接电离质谱仪技术的推广应用,提升一线执法服务水平。     

In situ analysis of soybeans and nuts by probe electrospray ionization mass spectrometry

The probe electrospray ionization (PESI) is an ESI‐based ionization technique that generates electrospray from the tip of a solid metal needle. In the present work, we describe the PESI mass spectra obtained by in situ measurement of soybeans and several nuts (peanuts, walnuts, cashew nuts, macadamia nuts and almonds) using different solid needles as sampling probes. It was found that PESI‐MS is a valuable approach for in situ lipid analysis of these seeds. The phospholipid and triacylglycerol PESI spectra of different nuts and soybean were compared by principal component analysis (PCA). PCA shows significant differences among the data of each family of seeds. Methanolic extracts of nuts and soybean were exposed to air and sunlight for several days. PESI mass spectra were recorded before and after the treatment. Along the aging of the oil (rancidification), the formation of oxidated species with variable number of hydroperoxide groups could be observed in the PESI spectra. The relative intensity of oxidated triacylglycerols signals increased with days of exposition. Monitoring sensitivity of PESI‐MS was high. This method provides a fast, simple and sensitive technique for the analysis (detection and characterization) of lipids in seed tissue and degree of oxidation of the oil samples. Copyright © 2015 John Wiley & Sons, Ltd.     

Silicon micropillar array electrospray chip for drug and biomolecule analysis

We have developed a lidless micropillar array electrospray ionization chip (microPESI) combined with mass spectrometry (MS) for analysis of drugs and biomolecules. The microPESI chip, made of silicon, contains a sample introduction spot for a liquid sample, an array of micropillars (diameter, height, and distance between pillars in the range of 15-200, 20-40, and 2-80 microm, respectively), and a sharpened tip for direct electrospray formation. The microchips were fabricated using deep reactive ion etching (DRIE) which results in accurate dimensional control. The chip, providing a reliable open-channel filling structure based on capillary forces and a electrospray emitter tip for ionization, allows an easy operation and reliable, non-clogging liquid transfer. The microPESI chip can be used for a fast analysis using single sampling or for continuous infusion measurements using a syringe pump for sample introduction. The microPESI-MS shows high sensitivity, with limit of detection 30 pmol/L (60 amol or 28 fg) for verapamil measured with tandem mass spectrometry (MS/MS) and using a sample volume of 2.5 microL. The system shows also good quantitative linearity (r2 > 0.99) with linear dynamic range of at least six orders of magnitude and good ion current stability (standard deviation <5%) in 1-h continuous flow measurement. The microPESI-MS is shown to be a very potential method for direct analysis of drugs and biomolecules.     

Easy dual-mode ambient mass spectrometry with Venturi self-pumping, canned air, disposable parts and voltage-free sonic-spray ionization

An exceptionally easy to assemble source for ambient mass spectrometry is described. Based on Venturi easy ambient sonic-spray ionization (V-EASI), the source was further simplified by the use of a can of compressed air which simultaneously provides solution or solvent Venturi self-pumping and continuous, stable and abundant low-noise ion signal via voltage-free sonic-spraying. Further simplification was also attained by the use of inexpensive and readily commercially available parts: a surgical 2-way catheter, an aerosol can of compressed air, a 30 cm long fused-silica capillary and a hypodermic needle. This "Spartan" V-EASI source seems to offer one of the easiest and cheapest ways to make ions for ambient desorption/ionization mass spectrometry analysis of both liquid and solid samples.     

Visualization of cancer‐related chemical components in mouse pancreas tissue by tapping‐mode scanning probe electrospray ionization mass spectrometry

Mass spectrometry imaging is an informative approach for the comprehensive analysis of multiple components inside biological specimens. We used novel tapping‐mode scanning probe electrospray ionization mass spectrometry method to visualize cancer‐related chemical components in the mouse pancreas tissue section at a sampling pitch of 100 µm. Positive ion mode measurements from m/z 100 to 1500 resulted in the visualization of multiple components that are tentatively assigned as polyamines, lipids and proteins. Their signal intensities inside the cancerous and the non‐cancerous regions were found to be significantly different by the two‐sample t‐test. Copyright © 2015 John Wiley & Sons, Ltd.     

New interface plate for microspray ionization mass spectrometry

A new interface plate was employed in microspray ionization mass spectrometry (μESI-MS) to improve ion transmission from the sprayer into the sampling nozzle of the mass spectrometer at atmospheric pressure. Using a time-of-flight mass spectrometer (TOFMS), a fivefold increase in ion intensity and a sevenfold reduction in method detection limit were observed. The interface plate attenuated the dependence of the ion intensity on the sprayer position. Even when the distance between the sprayer tip and sampling nozzle was 15.0 mm, ion signals were still stronger than when the sprayer tip was positioned 3.0 mm in front of the sampling nozzle with the original interface plate. This enhancement in the performance of μESI-MS was due to the improved shapes of the equipotential lines near the sprayer tip and the long desolvation distance between the sprayer and the sampling nozzle of the MS.     

Direct profiling of phytochemicals in tulip tissues and in vivo monitoring of the change of carbohydrate content in tulip bulbs by probe electrospray ionization mass spectrometry

Probe electrospray ionization (PESI) is a recently developed ESI-based ionization technique which generates electrospray from the tip of a solid needle. In this study, we have applied PESI interfaced with a time of flight mass spectrometer (TOF-MS) for direct profiling of phytochemicals in a section of a tulip bulb in different regions, including basal plate, outer and inner rims of scale, flower bud and foliage leaves. Different parts of tulip petals and leaves have also been investigated. Carbohydrates, amino acids and other phytochemicals were detected. A series of in vivo PESI-MS experiments were carried out on the second outermost scales of four living tulip bulbs to monitoring the change of carbohydrate content during the first week of initial growth. The breakdown of carbohydrates was observed which was in accordance with previous reports achieved by other techniques. This study has indicated that PESI-MS can be used for rapid and direct analysis of phytochemicals in living biological systems with advantages of low sample consumption and little sample preparation. Therefore, PESI-MS can be a new choice for direct analysis/profiling of bioactive compounds or monitoring metabolic changes in living biological systems.     

Atmospheric pressure ion lens extends the stable operational region of an electrospray ion source for capillary electrophoresis-mass spectrometry

An atmospheric ion lens incorporated into an electrospray ion source for capillary electrophoresis-mass spectrometry (CE-MS) is found to extend the stable operational regions for both flow rates and electrospray ionization (ESI) voltages. The stable operating conditions for the ESI source with and without the ion lens were characterized. The results showed that the stable operation region was widest when the voltage difference between the sprayer and the ion lens ranges from 2.6 to 2.8 kV, and under these condition, the CE-MS interface can be adapted to a broader range of electroosmotic and modifier flow rates. Modeling of the electric field in the electrospray ion source with the ion lens suggests that the extension of the stable region is attributed to the flatter equipotential surfaces around the sprayer tip and higher electric field strengths in the rest of the interface region.     

Desorption sonic spray ionization for (high) voltage-free ambient mass spectrometry

Sonic spray ionization is shown to create a supersonic cloud of charged droplets able to promote efficient desorption and ionization of drugs directly from the surfaces of commercial drug tablets at ambient conditions. Compared with desorption electrospray ionization (DESI), desorption sonic spray ionization (DeSSI) is advantageous since it uses neither heating nor high voltages at the spray capillary. DeSSI therefore provides a more friendly environment in which to perform ambient mass spectrometry (MS). DeSSI-MS is herein evaluated for the analysis of drug tablets, and found to be, in general, as sensitive as DESI-MS. The (high) voltage-free DeSSI method provides, however, cleaner mass spectra with less abundant solvent cluster ions and with enough abundant analyte signal for tandem mass spectrometry (MS/MS). These features may therefore facilitate the DeSSI-MS detection of low molar mass components or impurities, or both. The higher-velocity supersonic DeSSI spray also facilitates matrix penetration thus providing more homogenous sampling and longer lasting ion signals.     

Reduction of methylene blue during the ionization process

Methylene blue is readily reduced during the process of ionization in methods as diverse as electron ionization, direct exposure probe electron ionization, direct exposure probe chemical ionization, solid sample secondary ion mass spectrometry, liquid sample secondary ion mass spectrometry and fast atom bombardment mass spectrometry. The reduction of methylene blue need not initially involve the abstraction of hydrogen from the solvent present in the latter two methods.     

Continuous flow infrared matrix‐assisted laser desorption electrospray ionization mass spectrometry

Continuous flow infrared matrix‐assisted laser desorption electrospray ionization (CF IR MALDESI) mass spectrometry was demonstrated for the on‐line analysis of liquid samples. Samples in aqueous solution were flowed through a 50 µm i.d. fused‐silica capillary at a flow rate of 1–6 µL/min. As analyte aqueous solution flowed through the capillary, a liquid sample bead formed at the capillary tip. A pulsed infrared optical parametric oscillator (OPO) laser with wavelength of 2.94 µm and a 20 Hz repetition rate was focused onto the capillary tip for sample desorption and ablation. The plume of ejected sample was entrained in an electrospray to form ions by MALDESI. The resulting ions were sampled into an ion trap mass spectrometer for analysis. Using CF IR MALDESI, several chemical and biochemical reactions were monitored on‐line: the chelation of 1,10‐phenanthroline with iron(II), insulin denaturation with 1,4‐dithiothreitol, and tryptic digestion of cytochrome c. Copyright © 2010 John Wiley & Sons, Ltd.