Hydrophobic materials were successfully prepared from SPI and NR by blending via freezing/lyophilizing. The interfacial interaction, surface properties, hydrophobicity, and mechanical properties, biodegradability as well as the biocompatibility were investigated. The blend sheets exhibited good interface adhesion and good optical transparency. Their hydrophobicity was significantly improved compared with pure soy protein sheets. XPS results proved the NR surface enrichment. Flexibility and toughness of the blend sheets were enhanced and phase inversion phenomena were observed. Furthermore, the blend sheets exhibited good biodegradability and biocompatibility capable of supporting cell adhesion and proliferation.
Reproducible and controllable hydrophilic layers were grafted on macroporous PP membranes by surface initiated grafting. Two methods were adopted, i.e., through adsorption of or entrapping the photo‐initiator on the membrane surface. The latter method yielded longer grafted chains under otherwise identical conditions. Depending on monomer solution composition, brush layers or network‐like structures were grafted onto the entire membrane surface without significant loss of water flux. The influence of the structure of grafted layers on water permeation, protein adsorption, and protein microfiltration fluxes was investigated. It was found that membranes grafted with network‐like structures have the best performance.
Silica nanoparticles with an average diameter of 12 nm are grafted with PBMA‐b‐PMMA double shells through typical sequential ATRP from bromoisobutyrate initiators anchored at the silica surface using an epoxysilane. A commercially available PMMA homopolymer is used for the preparation of composites with unmodified, silane‐modified and double‐shell‐modified silica particles. Good mechanical properties are obtained for silica double shell containing systems. The silica content in double shell particle systems is varied from 0 to 2.5 wt%. A significant improvement in impact properties is observed. The surface‐modified silica particles are characterized by ATR‐FTIR, NMR, GPC, and thermal analyses. TEM analysis is used to analyze the nature of dispersion of particles in the composites.
The effect of aging on the thermo‐mechanical properties of new biocomposite materials obtained from renewable resources is studied. Cellulose was used as the reinforcing phase and the matrix was composed of a blend of two biopolymers (PEM and PLLA) in order to have a good compromise between stiffness and flexibility. Two grafting agents were used to compatibilize the filler with the matrix. The ensuing materials were then aged at 35 °C and 80% relative humidity during 45 days. Thermal and dynamic mechanical properties of the blends and composites were measured before and after aging. Important variations of crystallinity were observed and results show that grafting allowed obtaining high‐performance composites even after aging.
The effect of hydrophilic and hydrophobic nanosilica on the morphological, mechanical and thermal properties of polyamide 6 (PA) and poly(propylene) (PP) blends is investigated by extrusion compounding. Depending on the difference between the polymer/nanoparticle interfacial tensions, different morphologies are obtained as highlighted by TEM and SEM. Hydrophobic nanosilica migrates mainly at the PA/PP interface, which leads to a clear refinement of PP droplet size. The macroscopic properties of the hybrid blends are discussed and interpreted in relation with the blend morphology and melt‐mixing procedure. The control over coalescence allows a morphology refinement of the blends and improves mechanical properties.
Novel fluoroalkyl end‐capped oligomer/hydroxyapatite nanocomposites have been easily prepared by the reaction of disodium hydrogenphosphate and calcium chloride in the presence of self‐assembled molecular aggregates formed by fluoroalkyl end‐capped oligomers in aqueous media. The fluorinated hydroxyapatite nanocomposites thus obtained were found to exhibit a good dispersibility in a variety of media, and were applied to the surface modification of glass.
Strong honeycomb like nanocomposite sponges were fabricated from starch and PVA by using repeated cycles of freezing and thawing and reinforcing with cellulose whiskers. Their structure and properties were investigated with WAXD, FT‐IR, SEM, DMTA, rheological measurements, and LSCM. The results revealed that the repeated freezing/thawing cycles induced a physically crosslinked chain packing between starch and PVA, as well as a phase separation caused by the crystalline ice and syneresis. Thus, larger pores and tougher walls emerged in the sponges, leading to a high swelling degree. The sponges reinforced with cellulose whiskers exhibited improved dimensional stability and enhanced strength. These nanocomposite sponges are promising for wound dressing and tissue engineering applications.
Natural biomaterials were used to improve the biocompatibility of synthetic biopolymers. PCL was electrospun with natural biopolymers, silk fibroin, and small intestine submucosa. Due to increased electrical conductivity, the diameter of the composite fibers highly depended on the amount of SIS in the polymer solution. PCL/SF/SIS electrospun composites exhibited various synergistic effects, including enhanced mechanical properties and incredibly improved hydrophilicity compared to those of pure PCL and PCL/SF fibers. An initial cell attachment test demonstrated that the interactions between PC‐12 nerve cells and the PCL/SF/SIS composites were more favorable than those between PC‐12 cells and a PCL/SF composite.
A recently developed electrohydrodynamic printing method is described that can be used to create ordered structures and complex patterns using coarse processing needles and two polymeric materials. The results highlight the method's potential for direct 3D writing of biomedical polymers and composites for a variety of biomedical applications.
The design and synthesis of new fouling‐resistant coating materials, specifically PC‐substituted polyolefins, and their application to water purification membranes is described. Greatly improved fouling resistance is found for coated membranes subjected to environmentally relevant emulsified oil foulants. The coating method proves effective for reducing fouling on both UF and RO membranes, and for maintaining high rejection of organic material and salt. Providing membranes of various types with a coating that simultaneously gives high flux, fouling resistance, and foulant rejection represents a significant advance in membrane materials, and a promising route to extend membrane applications beyond what has been possible using conventional, known materials.
Orthopedic‐grade PMMA bone cement, admixed with prophylactic antibiotics, is widely used in hip and knee replacement surgery. There is a critical need to improve its structural integrity and to control antibiotic release. In this study, clay nanotubes are loaded with the antibiotic gentamicin sulfate and the cement is doped with 5–8 wt% nanotubes. The halloysite nanotubes isolate the drug from the cement monomers and serve as nanocontainers for sustained release of the antibiotic. Gentamicin‐loaded clay nanotubes admixed in PMMA cement provide sustained release up to 300–400 h and with enhanced release at cement cracks. The PMMA/halloysite/gentamicin composite tensile strength does not deteriorate as compared with pure cement and its adhesion to bone is significantly increased.
A novel model is presented for predicting the phase selective filler localization in an equilibrium state for ternary rubber blends of SBR, NBR, and NR. It is based on surface tension data of the rubber components and the filler. Phase‐selective filler localization in ternary rubber blends is determined experimentally by means of FTIR spectroscopy on the basis of the wetting concept. It is found that by preparation of ternary blends with certain silica loadings, pre‐mixed in each blend phase using the masterbatch technology, silica transfer processes between blend phases take place until the equilibrium filler distribution is reached. The sequence of the silica transfer processes can be explained by taking into consideration the formation of a phase‐in‐phase morphology of the ternary blend.
This paper demonstrates how the electric‐field‐assisted thermal annealing of octadecylamine‐functionalized SWNT/PMMA films induces an increase in the composite transversal conductivity of several orders of magnitude and a decrease in the lateral conductivity. This difference has been rationalized in terms of the nanotube alignment into the polymer matrix along the electric field direction. This result provides an initial understanding of how electric fields can be used to control the bulk physical properties of such nanocomposites.
A facile and easily industrialized approach for preparing highly dispersed MMT/polymer nanocomposites is developed by combining the latex compounding method and a spray‐drying process. Clay particles are successfully delaminated into layers, and layer re‐stacking is effectively prevented. HR‐TEM and XRD results confirm that MMT layers achieve exfoliated or nearly exfoliated dispersion in both MMT/styrene‐butadiene rubber and MMT/PS nanocomposites. Compared with melt‐blended MMT/SBR composites, MMT/SBR nanocomposites prepared by this new strategy exhibit extremely high dynamic modulus.
A novel CMRF is synthesized from modified silicone oil, containing composite polyurethane microsphere additives, and surface‐coated iron particles. The CMRF is designed to act as a liquid spring with controllable damping properties in a damper system. The fluid compressibility is characterized by force/displacement measurements. The addition of composite polyurethane‐microspheres increases the strength and compressibility of the fluid. It also decreases the concentration of iron particles needed in order to achieve the same yield stress as commercially available MRF. Surface coating surface of the iron particles with poly(2,3,4,5,6‐pentafluorostyrene) via RAFT provides dispersion stability.
A new, nickel‐coated graphite resistance‐change‐based method for gel‐point determination for epoxy‐based thermoset resins is presented and compared with DSC and rheological methods. Gelation times determined by this new method are in very good agreement with conventional techniques; this new method is potentially simpler and less time consuming than existing ones.
A diacrylate polysulfone oligomer is synthesized and used as the acrylic oligomer for the in situ synthesis of noble metal/PSU nanocomposites through UV‐induced simultaneous radical polymerization of acrylic functionalities and NP formation by reduction of their precursors. Thus, silver or gold NPs are formed in situ during polymer network formation. FESEM analysis of the morphology of the cured systems demonstrates that the nanoparticles of the noble metals are homogeneously distributed in the network without macroscopic agglomeration.
Epoxy/BaTiO3 hybrid materials are prepared as good candidates for organic capacitors. The hybrid system is cured by using camphorquinone and a iodonium salt through a free‐radical promoted cationic polymerization using a long‐wavelength tungsten halogen lamp. The cured films are fully characterized. Morphological characterization shows a well‐dispersed inorganic phase within the organic matrix. Electrical characterization demonstrates a linear increase of the dielectric constant with increasing filler content, while low dielectric loss values are obtained.
The report shows that simple LbL deposition of positively charged chitosan and negatively charged heparin can be used to efficiently modify the native surface of both NiTi and Ti without any previous treatments. Moreover, mineralization of the polymer multilayers with calcium phosphate leads to surfaces with low contact angles around 70 and 20° for NiTi and Ti, respectively. This suggests that a polymer multilayer/calcium phosphate hybrid coating could be useful for making NiTi or Ti implants that are at the same time antibacterial (via the chitosan), suppress blood clot formation (via the heparin), and favor fast endothelialization (via the improved surface hydrophilicity compared to the respective neat material).
Novel materials were prepared from dual photo and thermal polymerization of hybrid thiol‐ene/cationic systems. In the first stage, the thiol‐ene system proceeded to high conversions, while the cationic photopolymerization was inhibited. The formation of sulfides during this stage was the main factor for the inhibition of the cationic photopolymerization of the epoxy monomers. Once those sulfides were formed, they reacted with the oxonium‐terminated growing polyether chains to form trialkylsulfonium salts. These salts promoted the thermal polymerization of the epoxy monomers in the second stage. The viscoelastic properties of the resulting polymers were measured by DMA.
