Visible green upconversion luminescence of Er3+/Yb3+/Li+ co-doped CaWO4 particles

The upconversion (UC) luminescence of Li⁺/Er³⁺/Yb³⁺ co-doped CaWO₄ phosphors is investigated in detail. Single crystallized CaWO₄:Li⁺/Er³⁺/Yb³⁺ phosphor can be obtained, co-doped up to 25.0/5.0/20.0 mol% (Li⁺/Er³⁺/Yb³⁺) by solid-state reaction. Under 980 nm excitation, CaWO₄:Li⁺/Er³⁺/Yb³⁺ phosphor exhibited strong green UC emissions visible to the naked eye at 530 and 550 nm induced by the intra-4f transitions of Er³⁺ (²H_11/2,⁴S_3/2→⁴I_15/2). The optimum doping concentrations of Yb³⁺/Li⁺ for the highest UC luminescence were verified to be 10/15 mol%, and a possible UC mechanism that depends on the pumping power is discussed in detail.     

Bright red upconversion luminescence from Er3+ and Yb3+ co-doped ZnO-TiO2 composite phosphor powder

ZnO-TiO₂ composites co-doped with Er³⁺ and Yb³⁺ ions were successfully synthesized by powder-solution mixing method and their upconversion (UC) luminescence was evaluated. The effect of firing temperature, ZnO/TiO₂ mixing ratio, and dopant concentration ranges on structural and UC luminescence properties was investigated. The crystal structure of the product was studied and calculated in detail by means of X-ray diffraction (XRD). Also, the site preference of Er³⁺ and Yb³⁺ ions in the host material was considered and analyzed based on XRD results and UC luminescence characteristics. Brightest UC luminescence was observed in the ZnO-TiO₂:Er³⁺,Yb³⁺ phosphor fired at 1300 °C in which the system consisted of mixed phases; Zn₂TiO₄, TiO₂, RE₂Ti₂O₇ and RE₂TiO₅ (RE = Er³⁺ and/or Yb³⁺). Under the excitation of a 980 nm laser, the two emission bands were detected in the UC emission spectrum, weak green band centered at 544 and 559 nm, and strong red band centered at 657 and 675 nm wavelengths in accordance with ²H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 transitions of Er³⁺ ion, respectively. The simple chemical formula equations, for explaining the site preference of Er³⁺ and Yb³⁺ ions in host crystal matrix, were generated by considering the Zn₂TiO₄ crystal structure, its crystal properties, and the effect of Er³⁺ and Yb³⁺ ions to the host crystal matrix. The UC emission intensity of the products was changed by varying ZnO/TiO₂ mixing ratios, and Er³⁺ and Yb³⁺ concentrations. The best suitable condition for emitting the brightest UC emission was 1ZnO:1TiO₂ doped with 3 mol% Er³⁺, 9 mol% Yb³⁺ fired at 1300 °C for 1 h.     

Enhancement of up-conversion emission and emerging cool white light emission in co-doped Yb3+/ Er3+: Li2O-LiF-B2O3-ZnO glasses for photonic applications

A series of co-doped (Yb³⁺/Er³⁺): Li₂O-LiF-B₂O₃-ZnO glasses were prepared by standard melt quenching technique. Structural and morphological studies were carried out by XRD and FESEM. Phonon energy dynamics have been clearly elucidated by Laser Raman analysis. The pertinent absorption bands were observed in optical absorption spectra of singly doped and co-doped Yb³⁺/Er³⁺: LBZ glasses. We have been observed a strong up-conversion red emission pertaining to Er³⁺ ions at 1.0 mol% under the excitation of 980 nm. However, the up-conversion and down conversion (1.53 µm) emission intensities were remarkably enhanced with the addition of Yb³⁺ ions to Er³⁺: LBZ glasses due to energy transfer from Yb³⁺ to Er³⁺. Up-conversion emission spectra of co-doped (Yb³⁺/Er³⁺): LBZ glasses exhibits three strong emissions at 480 nm, 541 nm and 610 nm which are assigned with corresponding electronic transitions of ²H_9/2 → ⁴I_15/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 respectively. Consequently, the green to red ratio values (G/R) also supports the strong up-conversion emission. The Commission International de E′clairage coordinates and correlated color temperatures (CCT) were calculated from their up-conversion emission spectra of co-doped (Yb³⁺/Er³⁺): LBZ glasses. The obtained chromaticity coordinates for optimized glass (0.332, 0.337) with CCT value at 5520 K are very close to the standard white colorimetric point in cool white region. These results could be suggested that the obtained co-doped (Yb³⁺/Er³⁺): LBZ glasses are promising candidates for w-LEDs applications.     

Tb3+/Yb3+ co-doped Y2O3 upconversion transparent ceramics: Fabrication and characterization for IR excited green emission

Tb³⁺/Yb³⁺ co-doped Y₂O₃ transparent ceramics were fabricated by vacuum sintering of the pellets (prepared from nanopowders by uniaxial pressing) at 1750 °C for 5 h. Zr⁴⁺ and La³⁺ ions were incorporated in Tb³⁺/Yb³⁺ co-doped Y₂O₃ nanoparticle to reduce the formation of pores which limits the transparency of ceramic. An optical transmittance of ∼80% was achieved in ∼450 to 2000 nm range for 1 mm thick pellet which is very close to the theoretical value by taking account of Fresnel’s correction. High intensity luminescence peak at 543 nm (green) was observed in these transparent ceramics under 976 and 929 nm excitations due to Yb–Tb energy transfer upconversion.     

Down-conversion from Er3+-Yb3+ codoped CaMoO4 phosphor: A spectral conversion to improve solar cell efficiency

The present paper focuses on near infrared (NIR) down-conversion photoluminescence (PL) properties by studying the energy transfer mechanism between Er³⁺ and Yb³⁺ in CaMoO₄:Er³⁺, Yb³⁺ phosphors. We have successfully synthesized a series of Er³⁺ doped and Yb³⁺ codoped CaMoO₄ phosphors by hydrothermal method. The down-conversion of Er³⁺-Yb³⁺ combination with CaMoO₄ phosphor is designed to overcome the energy losses due to spectral mismatch when a high energy photon is incident on the Si-solar cell. The XRD, FESEM, EDX, PL, UV–Vis, Lifetime measurements were carried out to characterize the prepared down-converting phosphors. The crystallinity and surface morphology were studied by X-ray diffraction (XRD) and Field Emission Scanning Electron Microscopy (FESEM) techniques. The down-conversion PL spectra have been studied using 380 nm excitation wavelength. The Er³⁺ doped phosphors exhibit hypersensitive emission at 555 nm in the visible region due to ⁴S_3/2→⁴I_15/2 transition. The addition of Yb³⁺ into Er³⁺ doped CaMoO₄ attribute an emission at 980 nm due to ²F_5/2→²F_7/2 transition. The decrease in emission intensity in visible region and increase in NIR region reveals the energy transfer from Er³⁺ to Yb³⁺ through cross relaxation. The UV–Vis–NIR spectra shows the strong absorption peak around 1000 nm due to Yb³⁺ ion. The lifetime measurement also reveals the energy transfer from Er³⁺ to Yb³⁺ ions. The maximum value of energy transfer efficiency (ETE) and corresponding theoretical internal quantum efficiency are estimated as 74% and 174% respectively.     

Sintering of Yb3+:Y2O3 transparent ceramics in hydrogen atmosphere

Highly transparent Yb³⁺:Y₂O₃ ceramics with doping concentration up to 40.0 at.% had been fabricated successfully via hydrogen atmosphere sintering, where the raw powders were synthesized by co-precipitation method. The sintering temperature is about 600 °C lower than its melting temperature. SEM investigation revealed the average grain size of Yb³⁺:Y₂O₃ ceramics sintered at 1850 °C for 9 h was about 7 μm. The highest transmittance of as-prepared 1 mm thickness samples around wavelength of 1050 nm reached 80%, which is close to the theoretical value of Y₂O₃. The optical spectroscopic properties of Yb³⁺:Y₂O₃ transparent ceramics have also been investigated, which shows that it is a very good laser material for diode laser pumping and short pulse mode-locked laser.     

Influence of Yb3+ doping on phase stability and thermophysical properties of (Y1-xYbx)3Al5O12 under high temperature

In this work, Yb³⁺ was selected to replace the Y³⁺ in yttrium aluminum garnet (YAG) in order to reduce its thermal conductivity under high temperature. A series of (Y_1-xYb_x)₃Al₅O₁₂ (x=0, 0.1, 0.2, 0.3, 0.4) ceramics were prepared by solid-state reaction at 1600 °C for 10 h. The microstructure, thermophysical properties and phase stability under high temperature were investigated. The results showed that all the Yb doped (Y_1-xYb_x)₃Al₅O₁₂ ceramics were comprised of a single garnet-type Y₃Al₅O₁₂ phase. The thermal conductivities of (Y_1-xYb_x)₃Al₅O₁₂ ceramics firstly decreased and subsequently increased with Yb ions concentration rising from room temperature to 1200 °C. (Y_0.7Yb_0.3)₃Al₅O₁₂ had the lowest thermal conductivity among investigated specimens, which was about 1.62 W m⁻¹ K⁻¹ at 1000 °C, around 30% lower than that of pure YAG (2.3 W m⁻¹ K⁻¹, 1000 °C). Yb had almost no effect on the coefficients of thermal expansion (CTEs) of (Y_1-xYb_x)₃Al₅O₁₂ ceramics and the CTE was approximate 10.7×10⁻⁶ K⁻¹ at 1200 °C. In addition, (Y_0.7Yb_0.3)₃Al₅O₁₂ ceramic remained good phase stability when heating from room temperature to 1450 °C.     

Upconverting luminescence based dual-modal temperature sensing for Yb3+/Er3+/Tm3+: YF3 nanocrystals embedded glass ceramic

Yb³⁺/Er³⁺/Tm³⁺ doped transparent glass ceramic containing orthorhombic YF₃ nanoparticles was successfully synthesized by a melt-quenching method. After glass crystallization, tremendously enhanced (about 5000 times) upconversion luminescence, obvious Start-splitting of emission bands as well as long upconversion lifetimes of Er³⁺/Tm³⁺ confirmed the incorporation of lanthanide activators into precipitated YF₃ crystalline environment with low phonon energy. Furthermore, temperature-dependent upconversion luminescence behaviors of glass ceramic were systematically investigated to explore its possible application as optical thermometric medium. Impressively, both fluorescence intensity ratio of Er³⁺: ²H_11/2 → ⁴I_15/2 transition to Er³⁺: ⁴S_3/2 → ⁴I_15/2 one and fluorescence intensity ratio of Tm³⁺: ³F_2,3 → ³H₆ transition to the combined Tm³⁺: ¹G₄ → ³F₄/Er³⁺: ⁴F_9/2 → ⁴I_15/2 ones were demonstrated to be applicable as temperature probes, enabling dual-modal temperature sensing. Finally, the thermal effect induced by the irradiation of 980 nm laser was found to be negligible in the glass ceramic sample, being beneficial to gain intense and precise probing signal and detect temperature accurately.     

Concentration effects on the upconversion luminescence in Ho3+/Yb3+ co-doped NaGdTiO4 phosphor

Ho³⁺/Yb³⁺ co-doped NaGdTiO₄ phosphors were synthesized by a solid-state reaction method. The upconversion (UC) luminescence characteristics excited by 980 nm laser diode were systematically investigated. Bright green UC emission centered at 551 nm accompanied with weak red and near infrared (NIR) UC emissions centered at 652 and 761 nm were observed. The dependence of UC emission intensity on excitation power density showed that all of green, red and NIR UC emissions are involved in two-photon process. The UC emission mechanisms were discussed in detail. Concentration dependence studies indicated that Ho³⁺ and Yb³⁺ concentrations had significant influences on UC luminescence intensity and the intensity ratio of the red UC emission to that of the green one. Rate equations were established based on the possible UC mechanisms and a theoretical formula was proposed to describe the concentration dependent UC emission. The UC luminescence properties of the presented material was evaluated by comparing with commercial NaYF₄:Er³⁺, Yb³⁺ phosphor, and our sample showed a high luminescence efficiency and good color performance, implying potential applications in a variety of fields.     

Structural-phase state and lasing of 5–15 at% Yb3+:Y3Al5O12 optical ceramics

Yttrium aluminum garnet (Yb³⁺:Y₃Al₅O₁₂) laser ceramics doped by 5, 10 and 15 at% of ytterbium ions were obtained by reactive sintering. Optimal sintering temperature range for the formation of highly-dense transparent Yb³⁺:Y₃Al₅O₁₂ ceramics under normal recrystallization conditions was found to be T = 1750–1800 °C. The influence of Yb³⁺ ions on structural-phase state, phase composition, microstructure, optical and luminescent properties of sintered samples was experimentally investigated. It was shown that lattice parameter a of Yb³⁺:Y₃Al₅O₁₂ ceramics decreases linearly with increasing of Yb³⁺ concentration in a good agreement with L. Vegard’s rule, that indicates to the formation of (Y_1−xYb_x)₃Al₅O₁₂ (х = 0.05–0.15) substitutional solid solutions. No concentration quenching of Yb³⁺ luminescence was observed in Yb³⁺:Y₃Al₅O₁₂ within the 5–15 at% doping range. Quasi-CW lasing of Yb³⁺:Y₃Al₅O₁₂ ceramics was studied under diode-pumping at 970 nm. A highest slope efficiency of about 50% was obtained for 15 at%-doped Yb³⁺:Y₃Al₅O₁₂ ceramics sintered at T = 1800 °C for 10 h.     

Spectral pure RGB up-conversion emissions in self-assembled Gd2O3: Yb3+, Er3+/Ho3+/Tm3+ 3D hierarchical architectures

Self-assembled three-dimensional Yb³⁺(Ln = Er, Ho, Tm) co-doped Gd₂O₃ up-converted (UC) phosphors were synthesized by a facile co-precipitation method, and their morphologies and microstructures were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Under the excitation at 980 nm, spectral pure three primary colors red, green and blue (RGB) emissions were respectively achieved in Yb³⁺/Er³⁺, Yb³⁺/Ho³⁺ and Yb³⁺/Tm³⁺ co-doped Gd₂O₃ phosphors, in which spectral color purities were tuned by adjusting the doping concentration, annealing temperature, excitation power density and the pulse-width of 980 nm laser. These results provide deeper insights into modulating spectral color purities of up-converted emission, and the potential applications of spectrally pure RGB up-converted materials in fingerprint recognition and multi-color printing were also investigated.     

Y2O3:Yb,Tm and Y2O3:Yb,Ho powders for low-temperature thermometry based on up-conversion fluorescence

Recently, trivalent rare earth doped materials have received significant attention due to the strong temperature dependence of the fluorescence emission of these materials, which can be useful in temperature sensing. Here, we investigated Y₂O₃ ceramic powders doped with Yb³⁺ and co-doped with either Tm³⁺ or Ho³⁺. The powders were obtained via spray pyrolysis at 900 °C and additionally thermally treated at 1100 °C for 24 h. Structural characterization using X-ray powder diffraction confirmed the cubic bixbyte structure. Scanning electron microscopy (SEM) revealed that the particles exhibit a uniform spherical morphology. The up-conversion emissions were measured using laser excitation at 978 nm, resulting in the following transitions: blue emission in the range of 450–500 nm, weak red emission in the range of 650–680 nm and near infrared emission in the range of 765–840 nm for Tm³⁺, as well as green emission centered at 550 nm and weak near infrared emission at 755 nm for the Ho³⁺ ions. In addition, the temperature dependence of the fluorescence intensity ratios of different Stark components was analyzed in the range of 10–300 K. Significant temperature sensitivity was detected for several components, with the largest value of 0.097 K^?1 related to the intensity ratio of I₅₃₆ and I₇₇₂ emissions observed for the Y₂O₃:Yb,Ho powder.     

Up-conversion luminescence and optical thermometry properties of transparent glass ceramics containing CaF2:Yb3+/Er3+ nanocrystals

A series of Yb³⁺/Er³⁺ codoped transparent oxyfluoride glass ceramics with various amounts of Yb³⁺ have been successfully fabricated and characterized. Under 980 nm laser prompting, the samples produce intense red, green and blue up-conversion emissions, and the emission intensities increase with Yb³⁺ concentration and heat treatment temperature. Before losing good transparency in the visible region, optimum emission intensities are obtained for the sample with 25 mol% of Yb³⁺ at a heat treatment temperature of 680 °C. A possible up-conversion mechanism is proposed from the dependence of emission intensities on pumping power. The fluorescence intensity ratio between the two thermally coupled levels ²H_11/2 versus ⁴S_3/2 was measured with the laser output power of 57 mW to avoid the possible laser induced heating effect. The fluorescence intensity ratio values in the temperature range from 295 K to 723 K can be well fitted with the equation: A exp (−∆E/k_BT), where A = 6.79 and ∆E=876 cm⁻¹. The relative temperature sensitivity at 300 K was evaluated to be 1.4% K⁻¹. All the results suggest that the Yb³⁺/Er³⁺ codoped CaF₂ glass ceramics is an efficient up-conversion material with potential in optical fiber temperature sensing.     

Upconversion emission,cathodoluminescence and temperature sensing behaviors of Yb3+ ions sensitized NaY(WO4)2:Er3+ phosphors

A series of Yb³⁺ ions sensitized NaY(WO₄)₂:Er³⁺ phosphors were synthesized through a solid-sate reaction method. The X-ray diffraction (XRD), upconversion (UC) emission and cathodoluminescence (CL) measurments were applied to characterize the as-prepared samples. Under the excitation of 980 nm light, bright green UC emissions corresponding to (²H_11/2,⁴S_3/2)→⁴I_15/2 transitions of Er³⁺ ions were observed and the UC emission intensities showed an upward trend with increasing the Yb³⁺ ion concentration, achieving its optimum value at 25 mol%. Furthermore, the temperature sensing behavior based on the thermally coupled levels (²H_11/2,⁴S_3/2) of Er³⁺ ions was analyzed by a fluorescence intensity ratio technique. It was found that the obtained samples can be operated in a wide temperature range of 133–773 K with a maximum sensitivity of approximately 0.0112 K⁻¹ at 515 K. Ultimately, strong CL properties were observed in NaY(WO₄)₂:0.01Er³⁺/0.25Yb³⁺ phosphors and the CL emission intensity increased gradually with the increment of accelerating voltage and filament current.     

Color-tunable up-conversion emission from Yb3+/Er3+/Tm3+/Ho3+ codoped KY(MoO4)2 microcrystals based on energy transfer

Tunable up-conversion luminescent material KY(MoO₄)₂: Yb³⁺, Ln³⁺ (Ln=Er, Tm, Ho) has been synthesized by a typical hydrothermal process. Under 980 nm laser diode (LD) excitation, the emission intensity and the corresponding luminescence colors of KY(MoO₄)₂: Yb³⁺, Ln³⁺ (Ln=Er, Tm, Ho) have been investigated in detail. The energy transfer from the Yb³⁺ sensitizer to Ho³⁺, Er³⁺ and Tm³⁺ activators plays an important role in the development of color-tunable single- phased phosphors. The emission intensity keep balance through control of the Ho³⁺ co-doping concentrations, white light was experimentally shown at KY(MoO₄)₂: 20 mol% Yb³⁺, 0.8 mol% Er³⁺, 0.5 mol% Tm³⁺, 1.0 mol% Ho³⁺ phosphor with further calcination at 800 °C for 4 h under 980 nm laser excitation. The color tunability, high quality of white light and high intensity of the emitted signal make these up-conversion (UC) phosphors excellent candidates for applications in solid-state lighting.     

Improvement on the phase stability,mechanical properties and thermal insulation of Y2O3-stabilized ZrO2 by Gd2O3 and Yb2O3 co-doping

Gd₂O₃ and Yb₂O₃ co-doped 3.5 mol% Y₂O₃–ZrO₂ and conventional 3.5 mol% Y₂O₃–ZrO₂ (YSZ) powders were synthesized by solid state reaction. The objective of this study was to improve the phase stability, mechanical properties and thermal insulation of YSZ. After heat treatment at 1500 °C for 10 h, 1 mol% Gd₂O₃–1 mol% Yb₂O₃ co-doped YSZ (1Gd1Yb-YSZ) had higher resistance to destabilization of metastable tetragonal phase than YSZ. The hardness of 5 mol% Gd₂O₃–1 mol% Yb₂O₃ co-doped YSZ (5Gd1Yb-YSZ) was higher than that of YSZ. Compared with YSZ, 1Gd1Yb-YSZ and 5Gd1Yb-YSZ exhibited lower thermal conductivity and shorter phonon mean free path. At 1300 °C, the thermal conductivity of 5Gd1Yb-YSZ was 1.23 W/m K, nearly 25% lower than that of YSZ (1.62 W/m K). Gd₂O₃ and Yb₂O₃ co-doped YSZ can be explored as a candidate material for thermal barrier coating applications.     

Efficient near-infrared to visible and ultraviolet upconversion in polycrystalline BiOCl:Er3+/Yb3+ synthesized at low temperature

Er³⁺/Yb³⁺ co-doped BiOCl poly-crystals were synthesized by the conventional solid state method at 500 °C, which exhibited good crystalline and low phonon energy. Under 980 nm excitation, the samples showed intense red upconversion (UC) luminescence (Er³⁺: ⁴F_9/2→⁴I_15/2) as well as other four UC emission bands, including ultraviolet (UV) emission at 380 nm, violet emission at 411 nm, green UC emissions at 525 and 545 nm and near-infrared (NIR) emission between 800 and 850 nm, corresponding to the transitions of ⁴G_11/2, ²H_9/2, ²H_11/2, ⁴S_3/2 and ⁴I_9/2→⁴I_15/2 of Er³⁺, respectively. Interestingly, including the violet and green UC emissions, the red one originated a nearly three-photon process in this system, and a possible UC mechanism was proposed for the enhanced red emission.     

Fabrication and optical properties of Y2O3-based ceramics with broad emission bandwidth

In this article, we report on the fabrication and optical properties of highly transparent yttria ceramics for lasers active media with broadband gain profile. Laser synthesis method was used to produce Y₂O₃-based nanopowders doped with 1 mol.% Nd³⁺ or Yb³⁺ for these transparent ceramics. The additives of sesquioxides Lu₂O₃ and Sc₂O₃ were used along with ZrO₂ to disorder the crystalline structure. The porosity and average grain size decrease with these additives and the emission bandwidths of Nd³⁺ (⁴F_3/2 → ⁴I_11/2) and Yb³⁺ (²F_5/2 → ²F_7/2) transitions widen to 40 and 60 nm, respectively. Laser operation with the slope efficiency of 29% was obtained in [(Yb_0.01Lu_0.24Y_0.75)₂O₃]_0.88(ZrO₂)_0.12 ceramic sample.     

Power dependent upconversion in Er3+/Yb3+ co-doped BiNbO4 phosphors

In the present article, optical properties and energy upconversion in Er³⁺/Yb³⁺ co-doped BiNbO₄ matrix were investigated. The BiNbO₄ matrix was prepared using the solid-state reaction method. X-ray diffraction of the matrix shows that the crystal structure is consistent with ICSD code 74338. The grain distribution and the behavior of doping with Er³⁺ and Yb³⁺ on the sample surface were obtained by scanning electron microscope. Raman spectral characterization was carried out to examine the behavior of the vibrational modes of the samples. Upconversion emissions in the visible region at 484.5, 522, 541.5 and 670.5 nm in the matrices BiNbO₄:Er,Yb and BiNbO₄:Er were observed and analyzed as a function of 980 nm laser excitation power and rare-earth doping concentration. The results show that BiNbO₄ is a promising host material for efficient upconversion phosphors.     

Deep red upconversion photoluminescence in Er3+-doped Yb3Ga5O12 nanocrystalline garnet

The nanocrystalline single-phase Er³⁺-doped Yb₃Ga₅O₁₂ garnets have been prepared by the sol-gel combustion technique with a crystallite size of ≈30 nm. The presence of Yb³⁺ in garnet hosts allows their efficient excitation at the ≈977 nm wavelength. The Er³⁺ doping of Yb₃Ga₅O₁₂ garnet host results in deep red Er³⁺: ⁴F_9/2 → ⁴I_15/2 upconversion photoluminescence (UCPL) emission. The dominance of the red UCPL emission over the green Er³⁺: ⁴F_7/2/²H_11/2/⁴S_3/2 → ⁴I_15/2 component was investigated using the measurement of the steady-state and time-dependent Er³⁺ and Yb³⁺ emission spectra in combination with the power-dependent UCPL emission intensity. The proposed upconversion mechanism is discussed in terms of the Er³⁺ → Yb³⁺ energy back transfer process as well as Yb³⁺(Er³⁺) → Er³⁺ energy transfer and Er³⁺ ↔ Er³⁺ cross-relaxation processes. The studied Er³⁺-doped Yb₃Ga₅O₁₂ garnet may be utilized as a red upconversion emitting phosphor.