Fabrication and characterization of honeycomb β-tricalcium phosphate scaffolds through an extrusion technique

In this study, for the first time honeycomb β-tricalcium phosphate (β-TCP) scaffolds were fabricated through an extrusion technique. The physicochemical properties and cell behaviors of the honeycomb β-TCP scaffolds were investigated. The results showed that scaffolds were characterized by ordered channel-like macropores and unidirectional interconnection. The pore structure and mechanical strength could be tailored by changing the parameters of extrusion molds. The pore size of scaffolds was in the range of 400–800 µm approximately, while their compressive strength parallel to the pore direction and porosity ranged from 14 to 20 MPa and 60–70%, respectively. The in vitro cell behavior demonstrated that cells could well attach on the surfaces and grow into the inner channel-like pores of thescaffolds; the scaffolds with higher porosity showed better cell proliferation but poorer cell differentiation. The honeycomb scaffolds fabricated by extrusion technique are potential candidate for bone tissue engineering.     

Fabrication and characterization of porous β-tricalcium phosphate scaffolds coated with alginate

All porous materials have a common limitation which is lack of strength due to the porosity. In this study, two different methods have been used to produce porous β-tricalcium phosphate (β-TCP) scaffolds: liquid-nitrogen freeze casting and a combination of the direct-foaming and sacrificial-template methods. Among these two methods, porous β-TCP scaffolds with acceptable pore size and compressive strength and defined pore-channel interconnectivity were successfully fabricated by the combined direct-foaming and sacrificial-template method. The average pore size of the scaffolds was in the range of 100–150 µm and the porosity was around 70%. Coating with 4 wt% alginate on porous β-TCP scaffolds led to higher compressive strength and low porosity. In order to make a chemical link between the β-TCP scaffolds and the alginate coating, silane coupling agent was used. Treated β-TCP scaffold showed improvements in compressive strength of up to 38% compared to the pure β-TCP scaffold and 11% compared to coated β-TCP scaffold.     

Fabrication and compressive strength of porous hydroxyapatite scaffolds with a functionally graded core/shell structure

A novel type of porous hydroxyapatite (HA) scaffolds with a functionally graded core/shell structure was fabricated by freeze casting HA/camphene slurries with various HA contents into fugitive molds containing a graphite template with three-dimensionally interconnected pores for the creation of a highly porous core. All the fabricated samples had functionally graded core/shell structures with 3-D periodic pore networks in a core surrounded by a relatively dense shell. The overall porosity of the sample decreased from 60 to 38 vol% with increasing HA content in the HA/camphene slurry from 20 to 36 vol% due to a decrease in porosity in both the core and shell regions. In addition, the compressive strength was improved remarkably from 12 ± 1.1 to 32 ± 3.0 MPa. The in vitro cell test using a pre-osteoblast cell line showed that the samples had good biocompatibility.     

Fabrication and properties of porous β-tricalcium phosphate ceramics prepared using a double slip-casting method using slips with different viscosities

A new method to enhance the flexural strength of porous β-tricalcium phosphate (β-TCP) scaffolds was developed. This new method provides better control over the microstructures of the scaffolds and enhances the scaffolds’ mechanical properties. Using this technique, we were able to produce scaffolds with mechanical and structural properties that cannot be attained by either the polymer sponge or slip-casting methods alone or by simply combining the polymer sponge and slip-casting methods. The prepared scaffolds had an open, uniform, interconnected porous structure with a bimodal pore size of 100.0–300.0 μm. The flexural strength of the bimodal porous β-TCP scaffold sintered at 1200 °C was 56.2 MPa and had porosity of 61.4 vol%. The scaffolds obtained provide good mechanical support while maintaining bioactivity, and hence, these bioscaffolds hold promise for applications in hard-tissue engineering.     

Research of phase transformation induced biodegradable properties on hydroxyapatite and tricalcium phosphate based bioceramic

Biodegradable calcium phosphate composites consisting of tricalcium phosphate (α-TCP) and hydroxyapatite (HA) were prepared using a two-step sintering method. The ratio of α-TCP/HA was controlled by modulating the sintering temperature. The initial calcination process at 800 °C causes HA dehydroxylation and induces the early transformation of HA into α-TCP in subsequent sintering processes. At the optimum sintering temperature of 1300 °C, the material is comprised of a moderate ratio of α-TCP to HA (3:7) and possesses a hardness of 5.0 GPa. The high temperature phase transformation from HA to α-TCP accompanied by bonded water loss, which results in the formation of nano-pores within the α-TCP matrix, hardly deteriorated the mechanical strength of the composite. This pore-containing structure also provided a convincing evidence for the origin of the high degradability of α-TCP in a biological environment.     

Preparation and characterization of porous calcium-phosphate microspheres

Porous calcium-phosphate bioceramics are very important materials in bone tissue engineering. Recently, microsphere systems have been widely utilized in the treatment of defective tissues, including bone, cartilage and muscle. In this study, porous calcium-phosphate microspheres were prepared from calcium-deficient hydroxyapatite (d-HA) powders through a water-in-oil emulsion technique using camphene as the porogen and subsequently sintered at 700, 1100, 1200, or 1400 °C for 6 h. The microspheres produced in this study were characterized according to their morphology, properties, and biodegradation. The results indicated an interconnected porous structure with pore sizes ranging between several microns to as large as 250 μm. Approximately 35–50% of the pores were larger than 100 μm. In the microspheres sintered at 700 °C (Sample H), only the hydroxyapatite (HA) phase was present; when heated to 1100 °C (Sample BH), β-TCP was observed with HA; at 1200 °C (Sample ABH), the phase compositions included β-TCP and α-TCP, as well as a small quantity of HA; and at 1400 °C (Sample AH), the phases of samples included mainly α-TCP and HA. The degradation of the scaffolds was evaluated after immersion in distilled water for up to 28 days. Obvious dissolution and precipitation behavior was seen in the samples ABH and AH. The precipitates formed on the surface of ABH and AH could be carbonate-containing calcium-deficient HA (carbonated-CDHA) after immersion in distilled water for 28 days.     

Properties of calcium phosphates ceramic composites derived from natural materials

In this study, ceramics containing mixed phases of hydroxyapatite/beta-tricalcium phosphate (HA/β-TCP) were fabricated by a solid-state reaction technique. The HA powder was synthesized from cockle shells while the β-TCP powder was synthesized from egg shells. Pure HA and β-TCP fine powders were successfully obtained. The HA and β-TCP were mixed and subjected to a thermal treatment up to 1100 °C. To form the mixed phase ceramics, the resulting powders were sintered at 1350 °C. Effects of HA concentration on the properties of the studied ceramic were investigated. X-ray diffraction analysis revealed that all samples presented multiphase of calcium phosphate compounds. Average grain size of the ceramics decreased with the HA additive content. The 75 wt% HA ceramic showed the maximum hardness value (5.5 GPa) which is high when compared with many calcium phosphate ceramics. In vitro bioactivity test indicated that apatite forming increased with the HA additive content. To increase antibacterial activity, selected ceramics were coated with AgNO₃. Antibacterial test suggested that an Ag compound coating on the ceramics could improve the antibacterial ability of the studied ceramics. In addition, the antibacterial ability for the Ag coated ceramics depended on the porosity of the ceramics.     

Fabrication,characterization and cellular biocompatibility of porous biphasic calcium phosphate bioceramic scaffolds with different pore sizes

Facile wet-chemical methods are applied to synthesize hydroxyapatite and β-tricalcium phosphate nanoparticles, respectively. Porous biphasic calcium phosphate (BCP) bioceramic scaffolds are then fabricated using as-prepared HA and β-tricalcium phosphate nanoparticle powders. The macro pore diameter of BCP bioceramic scaffolds can be controlled by adjusting the amount of surfactants. The average diameter of the macro pores in BCP bioceramic scaffolds increases from 100 to 600 µm with the decrease amount of sodium dodecyl sulfate from 0.8 to 0.5 g, respectively. The BCP bioceramic scaffolds gradually degrade and the calcium-phosphate compounds fully deposit when soaking in simulated body fluid solution. Moreover, The BCP bioceramic scaffolds have outstanding biocompatibility to promote the cellular growth and proliferation of human dental pulp stem cells (hDPSCs). The hDPSCs also demonstrate favorable cellular adhering capacity on the pore surface of scaffolds, especially on the scaffolds with 100–200 µm pore diameter. The porous BCP bioceramic scaffold with inter-connected pore structure, outstanding in vitro cellular biocompatibility, favorable cell viability and adhesion ability will be a promising biomaterial for bone or dentin tissue regeneration.     

Polymer template fabrication of porous hydroxyapatite scaffolds with interconnected spherical pores

Porous hydroxyapatite (HA) scaffolds with interconnected spherical pores were fabricated by slip casting using a polymer template. Templates were produced using polymer beads, NaCl, and adhesive (N100). Effects of the preparation process on the pore structures and mechanical properties of the porous HA scaffolds were investigated. Pore interconnectivity was improved by adding NaCl particles with appropriate diameters to the polymer template. The size of the adhesive area could be controlled by adjusting the concentration of N100. The pore size could be controlled between 200 ± 42 and 400 ± 81 μm, and the porosity between 50.2 and 73.1%, by changing the size of the polymer beads and the volume of the NaCl particles. The compressive strength decreased as the porosity or pore size increased.     

Phase transformation on hydroxyapatite decomposition

The collapse of sintered hydroxyapatite (HA) has been attributed to HA decomposition; however, the detailed variations in microstructure are still unclear. Two phase transformation routes of HA decomposition during sintering were identified by transmission electron microscopy in this study. In the first route, HA is transformed to tetracalcium phosphate and needle-like β-tricalcium phosphate which is subsequently converted to α-tricalcium phosphate (α-TCP) above 1100 °C. In the second route, HA is transformed directly to α-TCP and calcium oxide at 1400 °C, accompanied by nanopore formation. In the second route, the α-TCP grew with a preferred orientation to form stripe-like grains. Further holding at 1400 °C for 4 h resulted in recrystallization; i.e., equi-axial grains formed within a stripe-like grain. Nanopore defects dispersed in the α-TCP grains are the main factor for the low density and decreased mechanical strength of the sintered bulk.     

EELS characterisation of β-tricalcium phosphate and hydroxyapatite

Hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) are of great interest due to their potential application as bone-replacement materials. In particular, composites made of a mixture of these Ca-phosphates revealed improved mechanical properties; however, the reason for this improvement is unknown. Future development and properties enhancement of such bioceramics is linked to the possibility to characterise their particular microstructure. In this context, the ability to quickly identify individual grains of HA and β-TCP within these composites will allow acquiring information about the phase distributions and the phase-boundary microstructure. The aim of the present study is, therefore, to demonstrate that electron energy-loss spectroscopy (EELS) can be successfully employed to differentiate between individual grains of HA and β-TCP. In particular, the analysis of the near-edge structure of the oxygen K-ionisation edge allows detection of a characteristic signal at ca. 536 eV that can be employed as an identification tool for HA. EELS investigations were performed first on as-received and calcined (1000 °C) HA and β-TCP powders and subsequently on pure bulk HA and β-TCP samples sintered at 1250 °C. Finally, this method was successfully applied to a HA/β-TCP (50/50 wt.%) composite sintered at 1250 °C.     

Clarifying the effect of sintering conditions on the microstructure and mechanical properties of β-tricalcium phosphate

The effect of the sintering conditions (temperature and time) on the microstructure (density and grain size) and mechanical properties (hardness, elastic modulus, and strength) of β-tricalcium phosphate (β-TCP) bioceramics fabricated from Ca-deficient commercial powders is analyzed. Contrary to current general opinion, it is demonstrated that the optimal sintering temperature to maximize the mechanical performance of this β-TCP material is not necessarily below the β ? α transformation temperature (1125 °C). In particular, optimal performance was achieved in samples sintered at 1200 °C for 3 h, since it was not until higher temperatures or longer sintering times that microcracking develops and mechanical properties are degraded. It is argued that the residual stresses developed during this reversible transformation do not lead to microcrack propagation until sufficiently large starting flaws develop in the microstructure as a consequence of grain growth. Implications of these findings for the processing routes to improve sintering of this important bioceramic are discussed.     

Preparation and characterization of iron/β-tricalcium phosphate bio-cermets for load-bearing bone substitutes

Ceramic-metal composite materials, namely cermets, are provided with characteristics of both ceramic and metal. Herein, for the first time bio-cermets based on β-tricalcium phosphate (β-TCP) bioceramic with biodegradable iron being reinforcement phase, were fabricated using the powder metallurgic method. The phase composition, microstructure, mechanical properties and in vitro cell behaviors of bio-cermets were investigated. The results revealed that atomic diffusion occurred between the iron and β-TCP matrix during the sintering process. The bio-cermets attained remarkable increase in fracture toughness (1.16–1.55 MPa m^1/2) compared to the β-TCP bioceramic (0.54 MPa m^1/2). The bio-cermets with 10 vol% iron showed the highest compressive strength (640 MPa), significantly higher than that of plain β-TCP bioceramic (285 MPa). The in vitro cell behaviors test indicated that the bio-cermets did not showed any sign of toxicity; the iron ions released from bio-cermets up-regulated bone-related gene expression of bone mesenchymal stem cells. The bio-cermets developed in this study represent potential bone substitutes for application in the load-bearing bone defects.     

The preparation and characterization of HA/β-TCP biphasic ceramics from fish bones

The aim of this research is to observe the physicochemical characterization and evaluate the biocompatibility of the HA/β-TCP biphasic calcium phosphate ceramics (BCP) produced from fish bones. In addition, the mechanism of the formation of BCP after calcination of fish bones was discussed. Three kinds of fish bones (Salmo salar, Anoplopoma fimbria and Sardine) were prepared and calcined for one hour at different temperatures ranging from 600 °C to 1100 °C in a muffle furnace. The calcined bones were analyzed by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (GTA), inductively coupled plasma optical atom emissions spectroscopy (ICP-OES), X-ray fluorescence (XRF) and scanning electron microscopy (SEM). The in vitro cytotoxicity assessment was used to evaluate the biocompatibility of the biphasic ceramics. BCP materials were produced from all kinds of fish bones by calcination above 700 °C, the carbonated hydroxyapatite and multiple trace element were also found in the calcined bones. With the increase of temperature, the ratio of HA/β-TCP varied and the major organic components were progressively removed. The carbonated hydroxyapatite disappeared when temperature rises above 900 °C. Rising temperature also caused crystal growth that eventually gave rise to the increase of the BCP grain size and influenced the mesoporous structure. The BCP materials were confirmed to have no obvious cytotoxicity to mesenchymal stem cells (MSC) in the in vitro cytotoxicity assessment. Calcium-deficient hydroxyapatite(CDHA) may make up the major inorganic constituent of fish bones that could decompose to HA and β-TCP when calcined above 700 °C. 800–900 °C is considered to be the optimal temperature to fabricate BCP materials which contain more β-TCP, carbonated hydroxyapatite and retain distinct mesoporous structure while has good biocompatibility. With the unique composition and structure, these three kinds of fish-bone-derived BCP materials can be further applied to fabricate bioceramic scaffolds for biomedical applications.     

Biphasic calcium phosphate scaffolds fabricated by direct write assembly: Mechanical,anti-microbial and osteoblastic properties

The present work reports on the fabrication of 3-D porous calcium phosphate scaffolds by robocasting from biphasic (HA/β-TCP ≈ 1.5) powders, undoped and co-doped with Sr and Ag. Scaffolds with different pore sizes and rod diameter of 410 μm were fabricated and sintered at 1100 °C. The size and morphology of the powder particles, and the concentrations of the processing additives, were shown to play major roles in the robocasting process. For all pore sizes tested, the compressive strength of scaffolds was comparable to or even higher than that of cancellous bone, and mechanical data could be systematically correlated with the porosity fraction. Co-doping the starting powders with Sr and Ag enhanced the mechanical strength of scaffolds, conferred good antimicrobial activity against Staphylococcus aureus and Escherichia coli, and did not induce any cytotoxic effects on human MG-63 cells. Furthermore, the co-doped powder was more effective in inducing pre-osteoblastic proliferation.     

Properties of hydroxyapatite/zirconium oxide nanocomposites

Effects of zirconium oxide (ZrO₂) nanoparticles additive on the microstructure and physical properties of hydroxyapatite (HA) were investigated. The HA powder was derived from natural bovine bone by a sequence of thermal processes. The composites containing nanoparticles of ZrO₂ (0.2–1.0 vol%) were fabricated by a solid-state reaction mixed oxide method. All samples showed traces of HA, beta-tricalcium phosphate (β-TCP) and alpha-tricalcium phosphate (α-TCP) phases while the x≥0.1 samples also showed ZrO₂ phase. Amount of β-TCP and α-TCP phases tend to decrease with ZrO₂. The additive inhibited grain growth as a result of a decrease in grain size. However, the x=0.2 sample exhibited higher hardness value which is consistent with the density data. In addition, bioactivity test suggested that the additive promoted an apatite forming with the values of Ca/P close to the value obtained from HA.     

Effects of strontium substitution on the phase transformation and crystal structure of calcium phosphate derived by chemical precipitation

This study focused on the effects of strontium substitution on the phase transformation and crystal structure of calcium phosphate. Chemical precipitation was used to prepare Sr-doped hydroxyapatite (HA) precursor powders. The phase transformation of the as-prepared samples during sintering was analyzed. The powders were characterized by X-ray diffraction, X-ray fluorescence spectroscopy, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Quantitative analysis of the phase content and fine structure was performed by Rietveld refinement. Sr doping was found to facilitate the phase transformation from HA to beta-tricalcium phosphate (β-TCP) at 1000 °C. The β-TCP content increased with increasing Sr content, causing a decline in the ratio of HA to β-TCP. With Sr contents of ≤5 mol%, HA remained the major phase in the biphasic mixtures; in contrast, with Sr contents of ≥15 mol%, the mass fraction of β-TCP exceeded 50%. The incorporation of Sr²⁺ into HA and β-TCP caused the lattice parameters of both phases to increase. Additionally, Sr incorporation slightly enhanced the binding energy of Ca. The study confirmed that Sr doping could be used to modulate the phase fractions of HA and β-TCP. The effective partial substitution of Sr in both HA and β-TCP makes these materials promising for bone repair.     

The threonine effect on calcium phosphate preparation from a solution containing Ca/P = 1.33 molar ratio

In this study, calcium phosphate materials were prepared by a modified precipitation method using high-speed dispersing equipment. A solution with a Ca/P molar ratio of 1.33 (octacalcium phosphate stoichiometry) was transferred into the reactor vessel with different concentrations of threonine at temperature 97 °C. A white precipitant was collected after the addition of condensed ammonium solution and the samples were subsequently calcined at 900 °C. From the XRD patterns and FT-IR spectra of the uncalcined samples, three phases of octacalcium phosphate (OCP), monetite (DCP) and hydroxyapatite (HA) were obtained. Calcined samples showed two phases of β-tricalcium phosphate (β-TCP) and calcium pyrophosphate (CPP). SEM micrographs showed the different morphology of samples. The specific surface areas (ssa) were 45–53 m²/g for and 5–6 m²/g for calcined samples. From the obtained results, we found that threonine added in various amounts in the initial solution inhibits the formation of HA and consequently creates OCP and DCP.     

Structure control of hydroxyapatite ceramics via an electric field assisted freeze casting method

Using H₂O₂ aqueous solution as pore-forming agent, hydroxyapatite (HA) porous scaffolds with both lamellar and spherical pores were fabricated by a freeze casting method. The highest porosity was obtained in HA scaffolds prepared using 5 vol% H₂O₂ aqueous solution. The relationship between the electric field intensity and the properties of HA scaffolds was investigated. Results showed that when the electric field intensity was increased from 0 to 90 kV/m, the average diameters of lamellar and spherical pores of HA scaffold were increased from 460 μm to 810 μm, and from 320 μm to 420 μm, respectively. Vitro cellular assay indicated that HA scaffold with both the lamellar and the spherical pores has a better biocompatibility, compared with that with single pores.     

Direct-write assembly of silicate and borate bioactive glass scaffolds for bone repair

Silicate (13-93) and borate (13-93B3) bioactive glass scaffolds were created by robotic deposition (robocasting) of organic solvent-based suspensions and evaluated in vitro for potential application in bone repair. Suspensions (inks) were developed, characterized, and deposited layer-by-layer to form three-dimensional scaffolds with a grid-like microstructure (porosity ≈50%; pore width 420 ± 30 μm). The mechanical response of the scaffolds was tested in compression, and the conversion of the glass to hydroxyapatite (HA)-like material in a simulated body fluid (SBF) was evaluated. As fabricated, the 13-93 scaffolds had a compressive strength 142 ± 20 MPa, comparable to the strength of human cortical bone, while the strength of the 13-93B3 scaffolds (65 ± 11 MPa), was far higher than that for trabecular bone. When immersed in SBF, the borate 13-93B3 scaffolds converted faster than the silicate 13-93 scaffolds to an HA-like material, but they also showed a sharper decrease in strength with immersion time. Based on their high compressive strength and bioactivity, the scaffolds fabricated in this work by robocasting could have potential application in the repair of load-bearing bone.