软土中张紧式吸力锚破坏标准模型试验与有限元分析

为了确定软土中张紧式吸力锚的破坏标准,采用自主研发的电动伺服加载装置,在荷载和位移控制方式下进行了张紧式吸力锚在最佳系泊点受静荷载作用的承载力模型试验。结果表明：不同的破坏模式,锚破坏时对应的位移也不同。当锚为竖向破坏时,对应锚沿系泊方向的位移约为0.6倍的锚径;当锚为水平破坏时,对应锚沿系泊方向的位移约为0.3倍的锚径。同时,按照模型试验所得的破坏标准确定的吸力锚的极限承载力与极限分析法的预测结果吻合较好。对足尺锚进行了有限元分析,将分析结果与极限分析法的预测结果进行比较,验证了模型试验所得位移破坏标准的合理性。     

软黏土中吸力锚承载特性离心试验研究

加载倾角和系泊点位置是吸力锚基础最重要的设计要素之一,能够改变锚体的破坏姿态以影响极限承载力。在饱和软黏土地基中选择不同的加载倾角及系泊点位置进行位移控制下的张紧式吸力锚离心模型试验,利用六自由度磁力计装置定量分析了加载倾角和系泊点位置对吸力锚破坏姿态与极限承载力的影响。研究发现,系泊点位置在锚体约2/3高度时,吸力锚发生平动破坏,当加载倾角由35°变化至20°时,在相同的系泊点位置,吸力锚发生后仰破坏,归一化极限承载力稍增大,并且达到极限承载力后仍保持一定的承载力余量;系泊点位置在锚体2/3高度以上时,吸力锚发生前倾破坏,归一化极限承载力降低了25%左右,并且破坏后的承载力余量大大降低。无论破坏模式如何,均未发现锚内土塞与锚有明显分离。     

软黏土中张紧式吸力锚循环承载力简化计算方法

张紧式吸力锚是一种重要的深水浮式平台基础。深水环境中,海底浅层沉积物多为饱和软黏土。软黏土中平均荷载与循环荷载共同作用下吸力锚的循环承载力对其设计至关重要。根据最佳系泊点受倾斜荷载作用下吸力锚的破坏模式,假设不同破坏区土体具有相同的平均剪应力,且平均剪应力与循环剪切强度比等于吸力锚所受静荷载与静荷载和循环荷载之和的比值。结合室内土性试验获得的饱和软黏土样不固结不排水归一化循环剪切强度随归一化平均剪应力的变化关系曲线,建立了破坏区土体不排水循环剪切强度的确定方法。对不同破坏区土体阻力进行分析,按照水平应力具有连续性这一特点,构建了上部滑动楔体破坏区与深部平面流动破坏区交界深度的计算方法,进而提出了计算吸力锚循环承载力的简化极限平衡方法。采用该方法对竖向和水平破坏模式吸力锚循环承载力模型试验结果进行了预测,预测与试验结果基本吻合,最小和最大偏差分别为0.79 %和16.08 %,平均偏差为5.74 %,可较好地反映吸力锚循环承载力随循环破坏次数增加而减小的变化关系,验证了该方法的可行性。     

竖向与水平复合加载下桶形基础承载性能的分析

在竖向和水平力共同作用的复合加载条件下地基承载性能及其破坏模式是吸力式桶形基础设计与施工中的关键技术问题。为此,以大型通用有限元分析软件系统ABAQUS为基础建立了桶形基础三维有限元计算模型,运用位移控制法确定了均质软黏土地基极限承载力系数与位移之间的归一化关系;采用Swipe试验加载方法,确定了桶形基础在竖向力与水平力平面上的地基破坏包络图,从极限分析上限方法的角度探讨了由数值计算所揭示的桶形基础破坏机制。     

软黏土中吸力锚循环失稳过程的模型试验

开展了张紧式吸力锚在侧壁最优系泊点处遭受平均荷载和循环荷载共同作用下的模型试验,着重研究了软黏土中吸力锚在等幅及变幅循环荷载下的变形失稳过程。研究发现,循环累积位移过大是锚发生破坏的主要原因。对于等幅循环加载试验,由于竖向附加荷重的施加,锚在水平向的循环累积位移要明显大于竖向,表现为明显的水平破坏模式。在特定的平均荷载水平下,循环荷载水平越高,锚的累积位移发展得越快,达到破坏所需的循环次数就越少。循环位移随循环次数的增长变化不明显,但随循环荷载水平的增大而增大。对于变幅循环加载试验,系泊点各方向的循环累积位移与循环位移均与循环荷载水平成正比。不同的循环加载时程下,锚的竖向累积位移均比水平累积位移大,表现为偏向于竖向破坏的中间破坏模式。锚前期的循环加载历史对后续加载产生的累积变形有明显影响。与静力加载相比,循环加载时锚的运动方向角有所增大,这可能是由于锚底孔压的累积要大于锚侧孔压的累积,从有效应力的角度分析,锚底有效应力的减少相对锚侧明显,进而使得锚竖向承载力减小得更多,导致锚的竖向运动更明显。     

基于耦合欧拉-拉格朗日法的锚板在黏土中的极限承载力数值分析

当结构在土体中运动时,往往导致土体发生较大的变形,此类问题采用大变形数值分析方法更为恰当。耦合欧拉-拉格朗日（Coupled Eulerian-Lagrangian, 简称CEL）法是大变形数值分析方法中的一种,在分析大变形问题时具有很强的适用性,但在国内尚未开展CEL法分析锚板承载力的研究。以方形锚板在均质土及线性土中的拔出试验为原型,基于CEL法建立数值模型,对锚板的极限承载力及破坏机制进行研究,并通过用户自定义子程序,实现了线性土的强度分布随锚板拔出而变化。计算结果表明,土体杨氏模量越大,锚板的极限承载力越大;随着位移增大,锚板的抗拔力先增大,后降低;当埋深小于临界埋深时,土体发生整体破坏;当埋深大于等于临界埋深时,土体发生局部破坏。数值计算反映的规律与试验结果基本吻合,体现了CEL法模拟锚板在海床中大位移响应的出色能力。     

软土中吸力式桶形基础倾覆承载性能离心模型试验

输电杆塔和风电机组基础主要承受上部结构倾覆弯矩荷载,倾覆承载性能是该类基础设计中的关键问题。针对饱和软黏土地基中的杆式结构桶形基础,通过开展位移控制循环加载、位移维持加载、力控制循环加载和单调静力加载离心模型试验,研究其倾覆承载能力。试验发现,当桶形基础达到极限承载力时其转动中心位置约在桶盖正下方0.8倍桶裙高度处;当循环倾覆弯矩幅值与极限抗弯承载力比值小于3/5时,桶形基础在循环过程中转角的累积难以持续增长,并逐渐趋于稳定;循环加载作用下土与结构相互作用刚度出现明显弱化,所获得的桶形基础循环弱化因子阈值约为0.15;位移维持加载的峰值荷载-位移曲线与单调静力加载的荷载-位移曲线较为一致,位移维持加载的谷值荷载-位移曲线对应的承载力较峰值荷载-位移曲线对应的承载力明显偏小,减少约30%～40%。     

基于上限法的条形锚板抗拔承载力分析

以极限分析上限理论为基础,利用旋转块体集的组合来构造条形锚板的运动许可速度场。分析了不排水黏土中深埋和浅埋条形锚板的抗拔承载力上限解,研究了锚板在不同埋置倾角和深度条件下的抗拔承载力和破坏面的特性,并将计算结果与已有计算方法进行了对比。分析结果表明：在不排水黏土中深埋条形锚板抗拔承载力与锚板的埋置方位和锚板的粗糙度无关,但完全光滑条件下破坏面扇圆部分的半径只有完全粗糙条件下的一半;在考虑无重土情况下浅埋条形锚板的抗拔承载力系数随锚板埋深比的增大而增大,破坏面也随埋深比的增加而逐渐扩大。所得上限解与已有文献解答较为吻合,而且求解所得破坏面更为直观,能为工程设计提供参考依据。     

非共面复合加载条件下桶形基础稳定性研究

采用荷载-位移联合搜索方法,对于饱和软黏土地基上裙板式桶形基础在水平荷载H、力矩M与扭矩T的非共面复合加载条件下的稳定性进行了比较系统的三维有限元分析,主要探讨了在不同荷载空间内桶形基础的破坏包络轨迹。在分析中,地基土服从基于Tresca屈服准则的理想弹塑性本构关系。计算结果表明,与传统共面复合加载情况相比,非共面复合加载条件下桶形基础的破坏包络面形状有较大差异。非共面复合加载情况下,包络面形状不依赖于基础埋深比,可用简单的圆或椭圆方程进行描述。根据有限元计算结果,将已有的三自由度破坏包络面方程扩展到六自由度复合加载空间内,进而初步建议了一个六自由度破坏包络面方程,并对于实际工程中常用的桶形基础埋深比,给出了方程中偏心度参数取值的确定方法。该方程可用来合理评价复杂荷载条件下软黏土地基上桶形基础承载力。     

正常固结黏土中平板锚基础的吸力和抗拉力

平板锚是新近出现的一种系泊深海浮式结构的基础型式。当黏土地基中的平板锚承受上拔力时,平板上、下表面超静孔压差形成的吸力使其抗拉承载力显著增加,对于风浪等快速加载条件尤其如此。利用有限元软件ADINA建立有效应力形式的轴对称动力有限元模型,研究圆形平板锚在缓慢加载与快速加载时的超静孔压分布与地基破坏型式。快速加载时重黏土和高岭土两组典型正常固结土样所得极限承载力系数与塑性极限分析解一致。进而通过变动参数分析,讨论加载速率和埋深对吸力和总抗拉力极限值的影响,并给出排水和不排水加载条件对应的临界加载速率。结果表明,不排水加载条件的总抗拉力可能达到排水总抗拉力的3倍。     

The modelling of anchors using the material point method

The ultimate capacity of anchors is determined using the material point method (MPM). MPM is a so‐called meshless method capable of modelling large displacements, deformations and contact between different bodies. A short introduction to MPM is given and the derivation of the discrete governing equations. The analysis of a vertically loaded anchor and one loaded at 45° is presented. The load–displacement curves are compared to that obtained from experiments and the effect of soil stiffness and anchor roughness is investigated. The results of the vertically loaded anchor are also compared to an analytical solution. The displacement of the soil surface above the anchor was measured and compared to the numerical predictions. Convergence with mesh refinement is demonstrated and the effect of mesh size and dilatancy angle on the shear band width and orientation is indicated. The results show that MPM can model anchor pull out successfully. No special interface elements are needed to model the anchor–soil interface and the predicted ultimate capacities were within 10% of the measured values. Copyright © 2005 John Wiley & Sons, Ltd.     

Interaction Effect of Group of Helical Anchors in Cohesive Soil Using Finite Element Analysis

In this paper, the interaction effect of a group of two and four symmetrical as well as asymmetrical helical anchors resting in homogeneous cohesive soil deposit with different helix configurations is determined using finite element analysis. The anchors were pulled to its ultimate failure controlling the displacement. Eight different types of anchor configuration were considered in the analysis, where mainly the number of helical plates, the depth of upper- and lower-most helical plates and the ratio of spacing between the helical plates to the diameter of the plate were varied. The variation of load–displacement curve for each anchor in the group was obtained and subsequently, the ultimate uplift capacity of each anchor was determined. The soil was assumed to follow Mohr–Coulomb failure criteria. The present theoretical observations are generally found in good agreement with those theoretical and experimental results available in the literature for single isolated helical anchor.     

砂土中扩体锚杆承载特性模型试验研究

在25个室内模型试验基础上,研究了均质砂土中竖向拉拔扩体锚杆的几何尺寸及埋深对其承载特性的影响。试验结果表明,根据深径比的不同,扩体锚杆可以分为浅埋与深埋扩体锚杆2种形式,它们在拉拔过程中均经历了土体弹性变形阶段、非扩体锚固段-土界面剪切破坏阶段、土体弹塑性变形阶段以及剪切破坏阶段,破坏特征分别表现为整体剪切破坏与局部剪切破坏。通过扩体锚杆与普通拉力型锚杆模型试验对比发现：与普通拉力型锚杆相比,扩体锚杆极限承载力、承载比与安全性均有大幅度提高。而通过增大扩体锚固段直径的方式提高扩体锚杆承载力的优势较为明显。此外,根据承载比分析,扩体锚杆存在最优扩体锚固段直径,因此,在实际工程中应寻找一个满足需要的最优扩体锚固段尺寸以取得较好的经济效益。     

利用循环强度分析张紧式吸力锚循环承载力的方法

按照在最佳系泊点受倾斜荷载作用的张紧式吸力锚的破坏机制,建议了利用软土不排水循环剪切强度计算软土中吸力锚循环承载力的极限平衡分析方法。该方法考虑了平均系泊荷载在土中引起的平均剪应力对土体循环剪切强度、进而对锚循环承载力的影响。为了说明该方法的可行性,进行了大量张紧式吸力锚在平均系泊荷载与循环荷载共同作用下的承载力模型试验。依据试验结果确定了锚被竖向拔出土层时系泊点的位移破坏标准,并据此确定了与不同模型试验条件对应的循环承载力。进而利用循环三轴试验确定的土层不排水循环强度随平均应力的变化关系和实测的土层剪切强度,通过极限平衡分析计算了与模型试验对应的循环承载力。计算与模型试验结果比较表明,对于张紧式吸力锚被竖向拔出土层的破坏模式,计算结果比模型试验结果偏大,平均偏大1.9%,绝大多数偏差在10%以内。因此,对于软土中的张紧式吸力锚,如果采用该方法计算与竖向拔出土层破坏模式相应的循环承载力时,将结果减小10%是恰当的。     

Seismic interference of two nearby horizontal strip anchors in layered soil

In the present analysis, an attempt is made to explore the seismic response of two nearby horizontal strip anchors embedded in non-homogenous c-? soil deposit at different depths. The analysis is performed by using two-dimensional finite-element software PLAXIS 2D. Each anchor carries equal static safe-working load without violating the ultimate uplift capacity under static condition. The soil is assumed to obey the Mohr?CCoulomb failure criterion. The behavior of single isolated anchor subjected to an earthquake loading is determined first to study the interference effect between two anchors. The horizontal acceleration response obtained from the Loma Prieta Gilroy Earthquake (1989) is considered as the input excitation in the analysis. A parametric study is performed by varying the clear spacing (S) between the anchors at different embedment ratios (??). The magnitude of vertical displacement, shear stress, and shear strain developed at different locations of the failure domain is determined for different clear spacings between the anchors.     

斜坡浅埋水平条形锚板抗拔承载力的极限分析

针对山区和丘陵等复杂地形下浅埋锚板抗拔承载力计算问题,基于极限分析上限定理、非线性Mohr-Coulomb强度准则及其关联流动法则,构造了斜坡浅埋水平条形锚板的曲线型破裂机制和机动许可速度场,采用变分极值原理获得了其上方土体破裂面方程和抗拔承载力的上限解,分析了斜坡倾角和锚板埋深对锚板抗拔承载力的影响。结果表明:随着斜坡倾角的增大,锚板抗拔承载力逐渐减小,此时其上方两侧土体破裂面不再对称且整体向下坡侧偏移;锚板抗拔承载力及其上方两侧土体破裂面宽度均随着埋深增大而增加;锚板埋深越小,斜坡倾角对其抗拔承载力的影响越大,应在计算中予以考虑,以更合理地反映斜坡浅埋水平条形锚板的抗拔承载特性。     

Numerical Investigation of the Inclined Pullout Behavior of Anchors Embedded in Clay

Two-dimensional plane strain finite element analysis has been used to simulate the inclined pullout behavior of strip anchors embedded in cohesive soil. Previous studies by other researchers were mainly concerned with plate anchors subjected to loads perpendicular to their longest axis and applied through the centre of mass. This paper investigates the behavior of vertical anchors subjected to pullout forces applied at various inclinations with respect to the longest anchor axis, and applied at the anchor top and through the centre of mass. The effects on the pullout behavior of embedment depth, overburden pressure, soil–anchor interface strength, anchor thickness, rate of clay strength increase, anchor inclination, load inclination and soil disturbance due to anchor installation were all studied. Anchor capacity is shown to increase with load inclination angle for anchors loaded through the centre of mass; greater effects are found for higher embedments. The results also show that anchor capacity improves at a decreasing rate with higher rates of increase of soil shear strength with depth. In addition, the capacity of vertically loaded anchors is shown to approximately double when the soil–anchor interface condition changes from fully separated to fully bonded. Similarly, disturbed clay strengths adjacent to the anchor following installation cause a significant reduction in anchor capacity. The results showed a significant effect of the point of load application for anchors inclined and normally loaded. The effects of other parameters, such as anchor thickness, were found to be less significant.