Effect of magnesia on the compressive strength of pellets

The compressive strength of MgO-fluxed pellets was investigated before and after they were reduced. The porosity and pore size of green pellets, product pellets, and reduced pellets were analyzed to clarify how MgO affects the strength of the pellets. Experimental results show that when the MgO-bearing flux content in the pellets increases from 0.0wt% to 2.0wt%, the compressive strength of the pellets at ambient temperature decreases, but the compressive strength of the pellets after reduction increases. Therefore, the compressive strength of the pellets after reduction exhibits no certain positive correlation with that before reduction. The porosity and pore size of all the pellets (with different MgO contents) increase when the pellets are reduced. However, the increase in porosity of the MgO-fluxed pellets is relatively smaller than that of the traditional non-MgO-fluxed pellets, and the pore size range of the MgO-fluxed pellets is relatively narrower. The reduction swelling index (RSI) is a key factor for governing the compressive strength of the reduced pellets. An approximately reversed linear relation can be concluded that the lower the RSI, the greater the compressive strength of the reduced pellets is.     

Effect of graphene oxide on the corrosion,mechanical and biological properties of Mg-based nanocomposite

This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts of GO(i.e.,0.5 wt%,1.0 wt%,and1.5 wt%)were fabricated by the semi-powder metallurgy method.The influence of GO on the MZM nanocomposite was analyzed through the hardness,compressive,corrosion,antibacterial,and cytotoxicity tests.The experimental results showed that,with the increase in the amount of GO(0.5 wt%and 1.5 wt%),the hardness value,compressive strength,and antibacterial performance of the MZM nanocomposite increased,whereas the cell viability and osteogenesis level decreased after the addition of 1.5 wt%GO.Moreover,the electrochemical examination results showed that the corrosion behavior of the MZM alloy was significantly enhanced after encapsulation in 0.5 wt%GO.In summary,MZM nanocomposites reinforced with GO can be used for implant applications because of their antibacterial performance and mechanical property.     

Microstructure and improved mechanical properties of ultrafine-grained Mo-12Si-8.5B (at.%) alloys with addition of ZrB2

Multi-hierarchical Mo-12Si-8.5B-x Zr B_2(x=0,0.5,1.0,1.5,2.5 wt%)alloys consisting of three ultrafine-grained(UFG,0.47–0.81μm)phases of Mo_5Si B_2(T2),Mo_3Si and Mo solid solution(α-Mo)were prepared by mechanical alloying following hot pressing.Microstructure observations showed that the intermetallic phases(Mo_3Si and T2)distributed dispersedly in the continuousα-Mo matrix associated with the homogeneously embedded nanoscaled particles(10–225 nm)in the grain interiors and at the grain boundaries.The Mo-12Si-8.5B-x Zr B_2alloys exhibited monotonically increasing compressive strength to 3.13 GPa with increasing content of Zr B_2,and the fracture toughness increased about 27%and reached at 11.5 MPa m~(1/2)at 1.0 wt%Zr B_2,rendering the Mo-12Si-8.5B-1.0 wt%Zr B_2alloy possessing the best combined mechanical properties of high strength and high toughness.The underlying reason for the superior mechanical properties of the Mo-12Si-8.5B-x Zr B_2alloys is that the dispersedly distributed nanosized particles in the UFG multi-phased-matrix can not only effectively block the dislocation motion to increase the strength but also store the dislocations to increase the strain hardening ability during mechanical deformation.     

Microstructure and mechanical properties of reaction-bonded B_4C–SiC composites

Reaction-bonded B_4C–SiC composites are highly promising materials for numerous advanced technological applications. However,their microstructure evolution mechanism remains unclear. Herein, B_4C–SiC composites were fabricated through the Si-melt infiltration process. The influences of the sintering time and the B_4C content on the mechanical properties, microstructure, and phase evolution were investigated. X-ray diffraction results showed the presence of SiC, boron silicon, boron silicon carbide, and boron carbide. Scanning electron microscopy results showed that with the increase in the boron carbide content, the Si content decreased and the unreacted B_4C amount increased when the sintering temperature reached 1650°C and the sintering time reached 1 h. The unreacted B_4C diminished with increasing sintering time and temperature when B_4C content was lower than 35 wt%. Further microstructure analysis showed a transition area between B_4C and Si,with the C content marginally higher than in the Si area. This indicates that after the silicon infiltration, the diffusion mechanism was the primary sintering mechanism of the composites. As the diffusion process progressed, the hardness increased. The maximum values of the Vickers hardness, flexural strength, and fracture toughness of the reaction-bonded B_4C–SiC ceramic composite with 12 wt% B_4C content sintered at 1600°C for 0.5 h were about HV 2400, 330 MPa, and 5.2 MPa·m~(0.5), respectively.     

Weldability and liquation cracking behavior of ZhS6U superalloy during electron-beam welding

The weldability of the ZhS6U nickel-based superalloy, which is prone to solidification cracking during electron-beam welding(EBW) repair processes, was investigated. The effects of two different pre-weld heat-treatment cycles on the final microstructure before and after welding were examined. Welds were made on flat coupons using an EBW machine, and the two heat-treatment cycles were designed to reduce γ′ liquation before welding. Microstructural features were also examined by optical and scanning electron microscopy. The results showed that the change in the morphology and size of the γ′ precipitates in the pre-weld heat-treatment cycles changed the ability of the superalloy to release the tensile stresses caused by the matrix phase cooling after EBW. The high hardness in the welded coupons subjected to the first heat-treatment cycle resulted in greater resistance to stress release by the base alloy, and the concentration of stress in the base metal caused liquation cracks in the heat-affected zone and solidification cracks in the weld area.     

Recrystallization and mechanical properties of WE43 magnesium alloy processed via cyclic expansion extrusion

In this study, cyclic expansion extrusion (CEE), as a relatively new severe plastic deformation (SPD) process, is applied to a rare earth (RE) containing Mg alloy WE43. The effects of the processing temperature and the number of passes are also investigated. The results showed that dynamic recrystallization (DRX) occurred after CEE processing at 400℃, and a bimodal structure with ultrafine DRXed grains surrounded the unrecrystallized grains. However, the DRX at 330℃ was retarded because of the existence of RE elements. The tensile tests showed that a simultaneous increase in the strength and the ductility of WE43 is obtained after CEE processing at 400℃ via two passes. Furthermore, the highest ultimate tensile strength of 440 MPa was achieved after the second pass of CEE at 330℃, and the highest ductility of 21% was attained after the second pass of CEE at 400℃. The microhardness measurements showed that the hardness increased from HV 80 to HV 114 and HV 98 after two passes of CEE processing at 330 and 400℃, respectively. In conclusion, increasing the processing passes could increase the mechanical properties and the volume fraction of the recrystallized grains. Moreover, increasing the temperature reduced the strength and the microhardness even if the elongation increased.     

反应键合B4C–SiC复合材料的组织和力学性能

Reaction-bonded B₄C–SiC composites are highly promising materials for numerous advanced technological applications. However, their microstructure evolution mechanism remains unclear. Herein, B₄C–SiC composites were fabricated through the Si-melt infiltration process. The influences of the sintering time and the B₄C content on the mechanical properties, microstructure, and phase evolution were investigated. X-ray diffraction results showed the presence of SiC, boron silicon, boron silicon carbide, and boron carbide. Scanning electron microscopy results showed that with the increase in the boron carbide content, the Si content decreased and the unreacted B₄C amount increased when the sintering temperature reached 1650°C and the sintering time reached 1 h. The unreacted B₄C diminished with increasing sintering time and temperature when B₄C content was lower than 35wt%. Further microstructure analysis showed a transition area between B₄C and Si, with the C content marginally higher than in the Si area. This indicates that after the silicon infiltration, the diffusion mechanism was the primary sintering mechanism of the composites. As the diffusion process progressed, the hardness increased. The maximum values of the Vickers hardness, flexural strength, and fracture toughness of the reaction-bonded B₄C–SiC ceramic composite with 12wt% B₄C content sintered at 1600°C for 0.5 h were about HV 2400, 330 MPa, and 5.2 MPa·m0.5, respectively.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

Effects of SiO_2 on the preparation and metallurgical properties of acid oxidized pellets

The effects of SiO_2 content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investigated.Mineralogical structures, elemental distribution, and pore size distribution were varied to analyze the mechanism of the effects.The results show that with an increase in SiO_2 content from 3.51 wt%to 7.18 wt%, compressive strength decreases from 3150 N/pellet to 2100 N/pellet and reducibility decreases from 76.5% to 71.4%.The microstructure showed that pellets with high SiO_2 content contained more magnetite in the mineralogical structures.Additionally, some liquid phases appeared, which hindered the continuous crystallization of hematite.Also, the softening–melting properties of the pellets clearly deteriorated as the SiO_2 content increased.With increasing SiO_2 content, the temperature range of the softening–melting zone decreased, and the maximum differential pressure and the comprehensive permeability index increased significantly.When acid oxidized pellets are used as the raw materials for blast furnace smelting, it should be combined with high basicity sinters to improve the softening–melting behaviors of the comprehensive charge.     

Assessment of deterioration in RHA-concrete due to magnesium sulphate attack

The assessment of magnesium sulphate attack on concretes containing rice husk ash (RHA, 20wt% of the cementitious materials) with various average particle sizes was investigated. The total cementitious materials were 390 kg and the water-to-binder ratio (W/B) was 0.53 for all mixtures. Specimens were initially cured in water for 7 d and then immersed in the 3wt% magnesium sulphate solution for up to 111 d of exposure. The specimens were subjected to drying-wetting cycles to accelerate sulphate attack. In addition to the visual monitoring of the specimens, the concrete specimens were subsequently tested for compressive strength, dynamic modulus of elasticity, and length and mass changes. The results show that the specimens exposed to sulphate attack exhibit higher strength and dynamic modulus than those kept in water. The length change is negligible and can be attributed to the normal swelling of concrete. On the other hand, concretes suffers mass loss and surface spalling and softening; the fine RHA-concrete results in a better resistance. For the accelerated sulphate attack method used in this study, mass change and visual monitoring are recommended for assessing the deterioration degree and the effectiveness of supplementary cementitious materials to resist sulphate attack.     

Effects of P addition on the microstructure and mechanical properties of Mg–5%Sn–1.25%Si alloy

The effects of Al-P addition on the microstructure and mechanical properties of as-cast Mg–5%Sn–1.25%Si magnesium alloy were investigated. The results show that the phases of the as-cast alloy are composed of α-Mg, Mg2 Sn, Mg2 Si, little P, and AlP. The Chinese character shape Mg2 Si phase changes into a granular morphology by P addition because AlP can act as a heterogeneous nucleation core for the Mg2 Si phase. When 0.225wt% of Al–3.5%P alloy is added, the mechanical properties of the Mg–5%Sn–1.25%Si alloy are greatly improved, and the tensile strength increases from 156 to 191 MPa, an increase of 22.4% compared to the alloy without P addition. When the amount of Al–3.5%P reaches 0.300wt%, a segregation phenomenon occurs in the granular Mg2 Si phase, and the tensile strength and hardness decrease though the elongation increases.     

Microstructure evolution and mechanical properties of a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy after a lower-temperature homogenization treatment

In this paper,a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy with a diameter of 600 mm was successfully prepared by the semi-continuous casting method.The alloy was subsequently annealed at a relatively low temperature of 430°C for 12 h as a homogenization treatment.The microstructure and room-temperature mechanical properties of the alloy were investigated systematically.The results show that the as-cast alloy contained a mass of discontinuous lamellar-shaped 18 R long-period stacking ordered(LPSO) phases with a composition of Mg10 Zn Y and an α-Mg matrix,along with net-shaped Mg5(Y,Gd) eutectic compounds at the grain boundaries.Most of the eutectic compounds dissolved after the homogenization treatment.Moreover,the amount and dimensions of the lamellar-shaped LPSO phase obviously increased after the homogenization treatment.The structure of the phase transformed into 14H-type LPSO with composition Mg12Zn(Y,Gd).The mechanical properties of the heat-treated large-sized alloy ingot are uniform.The ultimate tensile strength(UTS) and tensile yield strength(TYS) of the alloy reached 207.2 MPa and 134.8 MPa,respectively,and the elongation was 3.4%.The high performances of the large-sized alloy ingot after the homogenization treatment is attributed to the strengthening of the α-Mg solid solution and to the plentiful LPSO phase distributed over the α-Mg matrix.     

Evolution of the texture and mechanical properties of 2060 alloy during bending

In this study, we examined the evolution of the texture and mechanical properties of 2060 (T8) alloy during bending. A pixel rotation method (PRM) was proposed and used to characterize the textural evolution during bending determined by electron backscatter diffraction. The results showed that the textural components changed insignificantly, with the exception of a decrease in the cube texture. The tensile and yielding properties of the alloy were evaluated at three different orientations with respect to the rolling direction. The mechanical strength was found to increase in three directions with decreasing bending radius; thus, it was concluded that the 2060 (T8) alloy sheet satisfies the usage requirement after bending deformation.     

Effects of SiO2 on the preparation and metallurgical properties of acid oxidized pellets

The effects of SiO₂ content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investigated.Mineralogical structures, elemental distribution, and pore size distribution were varied to analyze the mechanism of the effects.The results show that with an increase in SiO₂ content from 3.51 wt%to 7.18 wt%, compressive strength decreases from 3150 N/pellet to 2100 N/pellet and reducibility decreases from 76.5% to 71.4%.The microstructure showed that pellets with high SiO₂ content contained more magnetite in the mineralogical structures.Additionally, some liquid phases appeared, which hindered the continuous crystallization of hematite.Also, the softening–melting properties of the pellets clearly deteriorated as the SiO₂ content increased.With increasing SiO₂ content, the temperature range of the softening–melting zone decreased, and the maximum differential pressure and the comprehensive permeability index increased significantly.When acid oxidized pellets are used as the raw materials for blast furnace smelting, it should be combined with high basicity sinters to improve the softening–melting behaviors of the comprehensive charge.     

Fine-tuning the ductile-brittle transition temperature of Mg_2Si intermetallic compound via Al doping

Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.     

Investigation on microstructural, mechanical and electrochemical properties of aluminum composites reinforced with graphene nanoplatelets

In present study, the microstructure, mechanical and electrochemical properties of aluminum–graphene nanoplatelets (GNPs) composites were investigated before and after extrusion. The contents of graphene nanoplatelets (GNPs) were varied from 0.25 to 1.0 wt.% in aluminum matrix. The composites were fabricated thorough powder metallurgy method, and the experimental results revealed that Al-0.25%GNPs composite showed better mechanical properties compared with pure Al, Al-0.50%GNPs and Al-0.1.0%GNPs composites. Before extrusion, the Al-0.25%GNPs composite showed ~13.5% improvement in ultimate tensile strength (UTS) and ~50% enhancement in failure strain over monolithic matrix. On the other hand, Al-0.50%GNPs and Al-0.1.0%GNPs composites showed the tensile strength lower than monolithic matrix. No significant change was observed in 0.2% yield strength (YS) of the composites. However, the extruded materials showed different trends. The 0.2%YS of composites increased with increase in GNPs filler weight fractions. Surprisingly, UTS of composites with 0.25 and 0.50% GNPs was lower than monolithic matrix. The failure strain of the baseline matrix was enhanced by ~46% with 0.25% graphene nanoplatelets. The superior mechanical properties (in terms of failure strain) of the Al-0.25%GNPs composite maybe attributed to 2-D structure, high surface area and curled nature of graphene. In addition, the corrosion resistance of pure Al and its composites reinforced with 0.5 and 1.0 wt% GNPs was also investigated. It was found that the corrosion rate increased considerably by the presence of GNPs.     

Tubular pure copper grain refining by tube cyclic extrusion–compression (TCEC) as a severe plastic deformation technique

Tube Cyclic Extrusion–Compression(TCEC) method is a novel severe plastic deformation technique developed for grain refining of cylindrical tubes to ultrafine grained(UFG)/nanostructured ones. In this method, tubes are fully constrained and deformed between chamber and mandrel with a small neck zone. The principle of TCEC technique which was adopted to impose severe plastic strains to the tubular materials was explained. Also, the deformation and grain fragmentation mechanism during TCEC was analyzed. The material deformation characteristics during TCEC were numerically simulated by FE code of ABAQUS/Explicit. The FEM results demonstrated that TCEC technique was able to impose extremely high plastic strains. The TCEC method was successfully applied to a commercially pure copper(99.99%) and significant grain refinement was achieved. TEM observation demonstrated the refinement of grains from the initial size of 45 μm to 200–350 nm after four processing cycles of TCEC. Microhardness measurements were carried out across the thickness of the initial and processed tubes. The results show good homogeneity of hardness distribution and an increase to 102 Hv from initial value of 55 Hv after four TCEC cycles. Mechanical properties of the specimens were extracted from tensile tests. The obtained results documented notable increase in the yield and ultimate strengths, whereas the uniform and total elongations decreased. Fracture surfaces after tensile tests were investigated by scanning electron microscopy(SEM), and the observed morphology indicates ductile fracture mode after four cycles of TCEC.     

AN INVESTIGATION ON THE ELECTROLYTIC SURFACE TREATMENT OF CARBON FABRICS

The composites obtained from carbon fibers have poor interlaminar shear strength beacuse ofthe few active polar groups on the carbon fiber surface and the weak bonding between the carbonfiber and the resin matrix. An electrolysis study to increase the surface acidic groups of the carbonfiber was investigated in this paper. Experimental results showed that the surface acidic groups,tensile strength, peeling strength of the carbon fabrics increased under certain electrolytic condi-tions, but the breaking elongations decreased. When the electrolytic conditions were too strong,tensile strength and peeling strength dropped down. Electronic scanning micrographs showed theengraved surfaces of carbon fibers after electrolysis.