Determination of heterogeneous electron transfer kinetics in the presence of ultrasound at microelectrodes employing sampled voltammetry

The technique of sampled voltammetry at microelectrodes irradiated with ultrasound is demonstrated for the first time. This technique is used to determine the heterogeneous electron transfer rate constants for the redox couples ferrocene/ferrocenium, Ru(NH(3))(6)(3+/2+), and IrCl(6)(3)(-)/IrCl(6)(2)(-). Determination of the heterogeneous rate constants is also achieved for comparison purposes by analysis of fast sweep rate voltammetry of the redox systems studied at microelectrodes and comparison of the results obtained to the theory developed by Nicholson and Shain. The heterogeneous rate constants determined using sampled voltammetry were 1.0, 0.6, 1.23, and 0.18 cm s(-)(1) for the ferrocene/ferrocenium (0.1 mol dm(-)(3) TEATFB, CH(3)CN), Ru(NH(3))(6)(3+/2+) (0.1 mol dm(-)(3) KCl), IrCl(6)(3)(-) (1 mol dm(-)(3) KCl), and IrCl(6)(3)(-)/IrCl(6)(2)(-) (1 mol dm(-)(3) NaCl), respectively, in agreement with those obtained in the absence of ultrasound.     

Poly(vinyl) chloride membrane copper-selective electrode based on 1-phenyl-2-(2-hydroxyphenylhydrazo)butane-1,3-dione

1-Phenyl-2-(2-hydroxyphenylhydrazo)butane-1,3-dione (H(2)L) was used as an effective ionophore for copper-selective poly(vinyl) chloride (PVC) membrane electrodes. Optimization of the composition of the membrane and of the conditions of the analysis was performed, and under the optimized conditions the electrode has a detection limit of 6.30×10(-7) M Cu(II) at pH 4.0 with response time 10s and displays a linear EMF versus log[Cu(2+)] response over the concentration range 2.0×10(-6) to 5.0×10(-3) M Cu(II) with a Nernstian slope of 28.80±0.11 mV/decade over the pH range of 3.0-8.0. The sensor is stable for 9 weeks and exhibits good selectivity with respect to alkali, alkali earth and transition metal ions (e.g. Na(+), K(+), Ba(2+), Ca(2+), Zn(2+), Cd(2+), Co(2+), Mn(2+), Ni(2+), Fe(2+), Al(3+)) in the 3.0-8.0 pH range. It was successfully applied for the direct determination of copper(II) in zinc, aluminum and nickel based alloys, in soils polluted by oil, and as an indicator electrode for potentiometric titration of copper ions with EDTA.     

Fluorophilic ionophores for potentiometric pH determinations with fluorous membranes of exceptional selectivity

Ionophore-doped sensor membranes exhibit greater selectivities and wider measuring ranges when they are prepared with noncoordinating matrixes. Since fluorous phases are the least polar and least polarizable liquid phases known, a fluorous phase was used for this work as the membrane matrix for a series of ionophore-based sensors to explore the ultimate limit of selectivity. Fluorous pH electrode membranes, each comprised of perfluoroperhydrophenanthrene, sodium tetrakis[3,5-bis(perfluorohexyl)phenyl]borate, and one of four fluorophilic H(+)-selective ionophores were prepared. All the ionophores are highly fluorinated trialkylamines containing three electron withdrawing perfluoroalkyl groups shielded from the central nitrogen by alkyl spacers of varying lengths: [CF(3)(CF(2))(7)(CH(2))(3)](2)[CF(3)(CF(2))(6)CH(2)]N, [CF(3)(CF(2))(7)(CH(2))(3)](2)(CF(3)CH(2))N, [CF(3)(CF(2))(7)(CH(2))(3)](3)N, and [CF(3)(CF(2))(7)(CH(2))(5)](3)N. Their pKa values in the fluorous matrix are as high as 15.4 +/- 0.3, and the corresponding electrodes exhibit logarithmic selectivity coefficients for H(+) over K(+) as low as <-12.8. The pKa and selectivity follow the trends expected from the degree of shielding and the length of the perfluoroalkyl chains of the ionophores. These electrodes are the first fluorous ionophore-based sensors described in the literature. The selectivities of the sensor containing [CF(3)(CF(2))(7)(CH(2))(5)](3)N are not only greater than those of analogous sensors with nonfluorous membranes but were of the same magnitude as the best ionophore-based pH sensors ever reported.     

Comparison of the conductivity properties of the tetrabutylammonium salt of tetrakis(pentafluorophenyl)borate anion with those of traditional supporting electrolyte anions in nonaqueous solvents

Cyclic voltammetry experiments at minielectrodes exhibit less ohmic error for lower polarity solvents when the supporting electrolyte anion is [B(C(6)F(5))(4)](-) rather than one of the smaller traditional anions such as [BF(4)](-), [PF(6)](-), or [ClO(4)](-). Conductance measurements have been performed for [NBu(4)][B(C(6)F(5))(4)] in tetrahydrofuran, dichloromethane, benzotrifluoride, and acetonitrile and compared with results for [NBu(4)](+) salts of several traditional anions in the same solvents. In solvents with dielectric constants of 10 or less, ion association constants, K(A), are as much as 2 orders of magnitude lower with [B(C(6)F(5))(4)](-), TFAB, as the electrolyte anion and the degree of this lowering is related to the acceptor property of the solvent. Analyses carried out on the basis of a Fuoss model attribute this fact to differences in concentrations of contact ion pairs rather than of solvent-separated ion pairs. The greater dissociation of the TFAB ion is attributed to its highly delocalized charge.     

An ion-selective electrode for acetate based on a urea-functionalized porphyrin as a hydrogen-bonding ionophore

An ion-selective electrode for acetate based on (α,α,α,α)-5,10,15,20-tetrakis[2-(4-fluorophenylureylene)phenyl]porphyrin as an ionophore that has no metal center and forms hydrogen bonds to the analyte is described. At pH 7.0 (0.1 M HEPES-NaOH buffer), the electrode based on this ionophore and cationic sites (50 mol % relative to the ionophore) responds to acetate in a linear range from 1.58 × 10(-)(4) to 1.58 × 10(-)(2) M with a slope of -54.8 ± 0.8 mV/decade and a detection limit of (3.06 ± 1.15) × 10(-)(5) M. Selectivity coefficients determined with the separate solution method (SSM) indicate that interferences of hydrophobic inorganic anions are relatively small (log[Formula: see text] (SSM): NO(3)(-), +0.68; SCN(-), +0.60; NO(2)(-), +0.22; I(-), +0.20; ClO(4)(-), +0.12; Br(-), -0.13). Responses to anions that are good hydrogen bond acceptors, i.e., Cl(-), HSO(3)(-), and HCO(3)(-), were Nernstian and were weaker than the response to acetate (log[Formula: see text] (SSM): -0.54, -0.56, and -1.34, respectively). Negligibly small responses were observed for very hydrophilic anions, i.e., F(-), SO(4)(2)(-), and H(2)PO(4)(-)/HPO(4)(2)(-). While aliphatic carboxylates such as formate, propanoate, pyruvate, and lactate gave Nernstian responses similar to acetate, interferences of salicylate and benzoate were considerably decreased in comparison with electrodes based on cationic sites only. Concentrations of acetic acid in vinegar samples were determined by direct potentiometry and agreed with values determined by a standard enzymatic method.     

Electrochemical determination of dopamine based on self-assembled peptide nanostructure

Self-assembled peptide nanostructures are electronically insulating as are most biomaterials derived from natural amino acids. To obtain additional properties and increase the applicability of peptide nanomaterials, some chemical modifications can be performed and materials can be functionalized to form hybrid compounds. In this work, we described the formation of L-diphenylalanine nanotubes (PNTs) with cyclic-tetrameric copper(II) species containing the ligand (4-imidazolyl)ethylene-2-amino-1-ethylpyridine [Cu(4)(apyhist)(4)](4+) in the Nafion membrane on a vitreous carbon electrode surface. This copper complex has been studied as structural and functional models for the active centers of copper containing redox enzymes. Scanning electron microscopy was used to confirm the formation of the nanostructures. The electrochemical properties of the PNT-[Cu(4)(apyhist)(4)](4+)/Nafion film on a glassy carbon electrode were characterized using cyclic voltammetry and square-wave voltammetry and showed high electrocatalytic activity toward the oxidation of dopamine (DA). The detection sensitivity was found to be enhanced by the use of copper(II) complex in the PNTs/Nafion films. Under the optimum conditions, the square-wave voltammetry peak height was linearly related to the DA concentration over two concentration intervals, viz., 5.0-40 μmol L(-1) and 40-1000 μmol L(-1). The detection limit was 2.80 μmol L(-1) (S/N = 3), and ascorbic acid did not interfere with the DA detection. These results suggested that this hybrid bioinorganic system provides an attractive advantage for a new type of electrochemical sensors. The detection sensitivity was found to be enhanced by use of PNTs.     

Synthesis, structural investigation, thermal decomposition mechanism and sensitivity properties of an energetic compound [Cd(DAT)(6)](ClO(4))(2) (DAT=1,5-diaminotetrazole)

An energetic coordination compound [Cd(DAT)(6)](ClO(4))(2) has been synthesized by using 1,5-diaminotetrazole (DAT) as ligand and its structure has been characterized by applying X-ray single crystal diffraction, elemental analysis and FT-IR spectroscopy. The central cadmium(II) cation is coordinated by six N atoms from six DAT molecules to form a six-coordinated and distorted octahedral structure. Di-dimension layer structure was formed and the layers were linked together by the extensive intermolecular hydrogen bonds between DAT ligands and ClO(4)(-) anions. Thermal decomposition mechanism of the title compound was predicted based on DSC, TG-DTG and FT-IR analyses results. The kinetic parameters of the first exothermic process of the title compound were studied by applying the Kissinger's and Ozawa-Doyle's methods. Sensitivity tests reveal that the title compound has sensitive nature.     

Structure, growth, and optical properties of TbAl3(BO3)4 single crystal

TbAl(3)(BO(3))(4) single crystal was grown from a K(2)Mo(3)O(10)-B(2)O(3) system using the top-seeded high temperature solution method (TSSG), 20 mm×9 mm×7 mm in size. The grown crystal was characterized by x-ray diffraction analysis showing that the crystal has a trigonal structure and the space group is R32 with lattice parameters of a = b = 9.293(13) ?, c = 7.249(6) ?. Faraday rotations of TbAl(3)(BO(3))(4) crystal were investigated at room temperature at wavelengths of 532, 633, and 1064 nm. Finally, the Verdet constants were measured at V = -108.8, -85.7, and -20.8 rad/mT for 532, 633, and 1064 nm, respectively.     

Stable tris(2,2'-bipyridine)ruthenium(III) for chemiluminescence detection

Two exceedingly stable [Ru(bipy)(3)](3+) reagents were prepared by dissolving either [Ru(bipy)(3)](ClO(4))(2) in acetonitrile (containing 0.05 M HClO(4)) or [Ru(bipy)(3)]Cl(2)·6H(2)O in 95:5 glacial acetic acid-acetic anhydride (containing 0.05 M H(2)SO(4)) followed by oxidation with PbO(2). These conveniently prepared solutions provide highly reproducible chemiluminescence detection over long periods of analysis, avoiding the need for recalibration or preparation of fresh reagent solutions and without the complications associated with online chemical or electrochemical oxidations. The reagent prepared in acetonitrile produced much greater signal intensities with a range of analytes and was deemed most suitable for high-performance liquid chromatography (HPLC) with postcolumn chemiluminescence detection.     

Mercury/homocysteine ligation-induced ON/OFF-switching of a T-T mismatch-based oligonucleotide molecular beacon

A molecular beacon (MB) with stem-loop (hairpin) DNA structure and with attached fluorophore-quencher pair at the ends of the strand has been applied to study the interactions of Hg(2+) ions with a thymine-thymine (T-T) mismatch in Watson-Crick base-pairs and the ligative disassembly of MB·Hg(2+) complex by Hg(2+) sequestration with small biomolecule ligands. In this work, a five base-pair stem with configuration 5'-GGTGG...CCTCC-3' for self-hybridization of MB has been utilized. In this configuration, the four GC base-pair binding energy is not sufficient to hybridize fully at intermediate temperatures and to form a hairpin MB conformation. The T-T mismatch built-in into the stem area can effectively bind Hg(2+) ions creating a bridge, T-Hg-T. We have found that the T-Hg-T bridge strongly enhances the ability of MB to hybridize, as evidenced by an unusually large MB melting temperature shift observed on bridge formation, ΔT(m) = +15.1 ± 0.5 °C, for 100 nM MB in MOPS buffer. The observed ΔT(m) is the largest of the ΔT(m) found for other MBs and dsDNA structures. By fitting the parameters of the proposed model of reversible MB interactions to the experimental data, we have determined the T-Hg-T bridge formation constant at 25 °C, K(1) = 8.92 ± 0.42 × 10(17) M(-1) from mercury(II) titration data and K(1) = 1.04 ± 0.51 × 10(18) M(-1) from the bridge disassembly data; ΔG° = -24.53 ± 0.13 kcal/mol. We have found that the biomarker of oxidative stress and cardiovascular disease, homocysteine (Hcys), can sequester Hg(2+) ions from the T-Hg-T complex and withdraw Hg(2+) ions from MB in the form of stable Hg(Hcys)(2)H(2) complexes. Both the model fitting and independent (1)H NMR results on the thymidine-Hg-Hcys system indicate also the high importance of 1:1 complexes. The high value of K(1) for T-Hg-T bridge formation enables analytical determinations of low concentrations of Hg(2+) (limit of detection LOD = 19 nM or 3.8 ppb, based on 3σ method) and Hcys (LOD = 23 nM, 3σ method). The conditional stability constants for Hg(Hcys)H(2)(2+) and Hg(Hcys)(2)H(2) at 52 °C have been determined, β(112) = 5.37 ± 0.3 × 10(46) M(-3), β(122) = 3.80 ± 0.6 × 10(68) M(-4), respectively.     

Studies on the Condensation Pathway to and Properties of Diiron Azadithiolate Carbonyls

Reaction of Fe(2)(SH)(2)(CO)(6) and HCHO, which gives Fe(2)[(SCH(2))(2)NH](CO)(6) in the presence of NH(3), affords the possible intermediate Fe(2)(SCH(2)OH)(2)(CO)(6), which has been characterized crystallographically as its axial-equatorial isomer. Fe(2)(SCH(2)OH)(2)(CO)(6) was shown to react with ammonia and amines to give Fe(2)[(SCH(2))(2)NR](CO)(6) (R = H, alkyl). Related hemithioacetal intermediates were generated by treatment of Fe(2)(SH)(2)(CO)(6) with RC(O)C(O)R (R = H, Ph, 4-F-C(6)H(4)) to give cycloadducts. The benzil derivative Fe(2)[S(2)C(2)(OH)(2)Ph(2)](CO)(6), a C(2)-symmetric species, was also characterized crystallographically. The acylated azadithiolate Fe(2)[(SCH(2))(2)NAc](CO)(6) was prepared by reaction of Li(2)Fe(2)S(2)(CO)(6) with (ClCH(2))(2)NC(O)Me. DNMR experiments show that the free energies of activation for rotation of the amide bond are the same for Fe(2)[(SCH(2))(2)NAc](CO)(6) and Fe(2)[(SCH(2))(2)NAc](CO)(4)(PMe(3))(2), which implies that the ligands on the iron centers do not strongly affect the basicity of the nitrogen. As a control, we showed that the thioamide Fe(2)[(SCH(2))(2)NC(S)Me](CO)(6) does exhibit a significantly higher barrier to rotation, attributable to the increased double-bond character of the N-C(S) bond.     

Electrochemical performance of diamond thin-film electrodes from different commercial sources

The electrochemical properties of two commercial (Condias, Sumitomo) boron-doped diamond thin-film electrodes were compared with those of two types of boron-doped diamond thin film deposited in our laboratory (microcrystalline, nanocrystalline). Scanning electron microscopy and Raman spectroscopy were used to characterize the electrode morphology and microstructure, respectively. Cyclic voltammetry was used to study the electrochemical response, with five different redox systems serving as probes (Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/)(2+), IrCl(6)(2)(-)(/3)(-), 4-methylcatechol, Fe(3+/2+)). The response for the different systems was quite reproducibile from electrode type to type and from film to film for electrodes of the same type. For all five redox systems, the forward reaction peak current varied linearly with the scan rate(1/2) (nu), indicative of electrode reaction kinetics controlled by mass transport (semi-infinite linear diffusion) of the reactant. Apparent heterogeneous electron-transfer rate constants, k degrees (app), for all five redox systems were determined from deltaE(p)-nu experimental data, according to the method described by Nicholson (Nicholson, R. S. Anal. Chem. 1965, 37, 1351.). The rate constants were also verified through digital simulation (DigiSim 3.03) of the voltammetric i-E curves at different scan rates. Good fits between the experimental and simulated voltammograms were found for scan rates up to 50 V/s. k degrees (app) values of 0.05-0.5 cm/s were observed for Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/2+), and IrCl(6)(2)(-)(/3)(-) without any extensive electrode pretreatment (e.g., polishing). Lower k degrees (app) values of 10(-)(4)-10(-)(6) cm/s were found for 4-methylcatechol and Fe(3+/2+). The voltammetric responses for Fe(CN)(6)(3)(-)(/4)(-) and Ru(NH(3))(6)(3+/2+) were also examined at all four electrode types at two different solution pH (1.90, 7.35). Since the hydrogen-terminated diamond surfaces contain few, if any, ionizable carbon-oxygen functionalities (e.g., carboxylic acid, pK(a) approximately 4.5), the deltaE(p), i(p)(ox), and i(p)(red) values for the two systems were, for the most part, unaffected by the solution pH. This is in contrast to the typical behavior of oxygenated, sp(2) carbon electrodes, such as glassy carbon.     

Thermo-optic coefficients and thermal lensing in Nd-doped KGd(WO4)2 laser crystals

We measured the thermo-optic coefficients dn/dT of anisotropic Nd:KGd(WO(4))(2) crystals at the wavelengths of 1.064 μm and 532 nm (300 K) by a beam deflection method. The values of dn/dT are determined to be dn(p)/dT = -16.0 × 10(-6) K(-1), dn(m)/dT = -11.8 × 10(-6) K(-1), and dn(g)/dT = -19.5 × 10(-6) K(-1) (at 1.064 μm) and dn(p)/dT = -14.3 × 10(-6) K(-1), dn(m)/dT = -10.0 × 10(-6) K(-1), and dn(g)/dT = -15.0 × 10(-6) K(-1) (at 532 nm). Thermal lensing in the flashlamp-pumped N(p)- and N(g)-cut Nd:KGd(WO(4))(2) laser rods was studied at 1.064 μm by a probe beam technique in the nonlasing conditions, and the contribution of the photoelastic term to the thermal lens optical power was estimated. Athermal propagation directions with the definitions dn/dT + (n-1)α(T) = 0 and dn/dT + nα(T) = 0 were found in Nd:KGd(WO(4))(2).     

Regeneration of hexamminecobalt(II) catalyzed by activated carbon treated with KOH solutions

The combined elimination of NO and SO(2) can be realized by hexamminecobalt(II) solution which is formed by adding soluble cobalt(II) salt into the aqueous ammonia solution. Activated carbon is used as a catalyst to regenerate hexamminecobalt(II), Co(NH(3))(6)(2+), so that NO removal efficiency can be maintained at a high level for a long time. In this study, KOH solution has been explored to modify coconut activated carbon to meliorate its catalytic performance in the reduction of hexamminecobalt(III), Co(NH(3))(6)(3+). The experiments have been performed in a batch stirred cell to investigate the effects of KOH concentration, impregnation duration, activation temperature and activation duration on the performance of activated carbon. The results show that the best KOH concentration for the improvement of activated carbon is 0.5 mol l(-1). The optimal impregnation duration is 9h. High temperature is favorable to ameliorating the catalytic performance of activated carbon. The optimum activation duration is 4h.     

Anticancer Activity of Self-Assembled Molecular Rectangles via Arene-Ruthenium Acceptors and a New Unsymmetrical Amide Ligand

Two new and large molecular rectangles 4 and 5 were synthesized from two different arene-ruthenium [Ru(2)(μ-η(4)-C(2)O(4))(MeOH)(2)(η(6)-p-Pr(i)C(6)H(4)Me)(2)][O(3)SCF(3)](2) (2), and [Ru(2) (p-cymene)(2) (donq) (OH(2))(2)] [O(3)SCF(3)](2) (donq = 5,8-dioxydo-1,4-naphthaquinonato) (3) acceptors and a new unsymmetrical N-(4-(pyridin-4-ylethynyl)phenyl) isonicotinamide (1) donor ligand. X-ray crystallography of 4 confirmed a molecular rectangle. The (1)H NMR spectra of both rectangles 4 and 5 showed a mixture of two structural, head-to-tail (HTL) and head-to-head (HTH) type, isomers in a 1:1 ratio. The cytotoxicities of both rectangles have been established against Colo320 (colorectal cancer), A549 (lung cancer), MCF-7(breast cancer) and H1299 (lung cancer) human cancer cell lines. The cytotoxicity of rectangle 5 was found to be considerably stronger against all cancer cell lines than that of the reference drug cisplatin.     

Infinite-dilution diffusion coefficients of complex ions from solution conductivity data

A technique is presented for determining infinite-dilution diffusion coefficients of complex ions from solution conductivity data. The method involves measuring the conductivities of dilute solutions in which the distribution of complex ions is systematically varied and statistically regressing the data to an equation that effectively relates individual ion diffusion coefficients to solution conductivity. The procedure is simple and requires no specialized equipment to perform. Unlike methods that require a concentration gradient, the solution composition is homogeneous and at equilibrium during measurements, which is a significant advantage when labile complexes are being studied. In this paper, diffusion coefficients of cuprous cyanide complexes are determined. Statistical analysis yields the infinite-dilution diffusion coefficients of Cu(CN)(2)(-), Cu(CN)(3)(2-), and Cu(CN)(4)(3-) at 25 °C as 1.43 × 10(-5) ± 9%, 1.08 × 10(-5) ± 9%, and 6.21 × 10(-6) ± 22% cm(2)/s, respectively.     

Thermolysis of some transition metal nitrate complexes with 1,4-diamino butane ligand

Four complexes are prepared and characterized having molecular formula [Zn(dab)(2)](NO(3))(2), [Cu(dab)(2)](NO(3))(2).H(2)O, [Ni(dab)(2)](NO(3))(2).2H(2)O and [Mn(dab)(2)](NO(3))(2), where dab: 1,4-diaminobutane. Thermolyses of these complexes were investigated by simultaneous thermogravimetry (TG), derivatives thermogravimetry (DTG), differential thermal analysis (DTA) and differential scanning calorimetry (DSC). The kinetics of the thermolysis at early stages is investigated using isothermal TG by applying model-fitting and isoconversional method. Thermolytic process is slow in inert (N(2)) and is fast in air atmosphere due to oxidative nature. To investigate the response of these complexes under the condition of rapid heating, ignition delay (D(i)) has been measured. Thermal stability of the complexes was found to increase in the order Mn < Cu < Ni < Zn.     

Large-amplitude Fourier transformed high-harmonic alternating current cyclic voltammetry: kinetic discrimination of interfering Faradaic processes at glassy carbon and at boron-doped diamond electrodes

Significant advantages of Fourier transformed large-amplitude ac higher (second to eighth) harmonics relative to responses obtained with conventional small-amplitude ac or dc cyclic voltammetric methods have been demonstrated with respect to (i) the suppression of capacitive background currents, (ii) the separation of the reversible reduction of [Ru(NH(3))(6)](3+) from the overlapping irreversible oxygen reduction process under conditions where aerobic oxygen remains present in the electrochemical cell, and (iii) the kinetic resolution of the reversible [Ru(NH(3))(6)](3+/2+) process in mixtures of [Fe(CN)(6)](3-) and [Ru(NH(3))(6)](3+) at appropriately treated boron-doped diamond electrodes, even when highly unfavorable [Fe(CN)(6)](3-) to [Ru(NH(3))(6)](3+) concentration ratios are employed. Theoretical support for the basis of kinetic discrimination in large-amplitude higher harmonic ac cyclic voltammetry is provided.     

Interactions of vitamin K3 with herring-sperm DNA using spectroscopy and electrochemistry

By means of ultraviolet-visible (UV-Vis) and fluorescence spectra, the binding ratio between vitamin K(3) and herring-sperm DNA in a physiological pH environment (pH = 7.40) was determined as n(K3):n(DNA) = 2:1, and the binding constants of vitamin K(3) binding to DNA at different temperatures were determined as K(θ)(298K) = 1.28 × 10(5) L·mol(-1) and K(θ)(310K) = 7.19 × 10(4) L·mol(-1), which were confirmed using the double reciprocal method are Δ(r)H(m)(θ) = -3.57 × 10(4) J·mol(-1), Δ(r)G(m)(θ) = -2.92 × 10(4) J·mol(-1), and Δ(r)S(m)(θ) = 217.67 J·mol(-1)K(-1). The driving power of this process was enthalpy. An intercalation binding of the vitamin K(3) with DNA was supported by a competitive experiment using acridine orange (AO) as a spectral probe. By combination analysis of the Scatchard method and cyclic voltammetry, we suggested that the interaction mode between vitamin K(3) and herring-sperm DNA would be a mixed mode. The quinonoid, duality fused-ring of vitamin K(3) can intercalate into the base pairs of DNA, and there is an electrostatic binding along with intercalation binding.