Improving the shear strength of Sn–Ag–Cu–Ni/Cu–Zn solder joints via modifying the microstructure and phase stability of Cu–Sn intermetallic compounds

This study focuses on the correlation between high-speed impact tests and the interfacial reaction in Sn-3.0Ag-0.5Cu-0.1Ni/Cu (wt%) and Sn-3.0Ag-0.5Cu-0.1Ni/Cu-15Zn solder joints. Adding Ni into the Sn–Ag–Cu solder alters the interfacial morphology from scallop type to layer type and exhibits high shear strength after reflow in both solder joints. However, the shear strength of Sn-3.0Ag-0.5Cu-0.1Ni/Cu solder joints degrades significantly after thermal aging at 150 °C for 500 h. It is notable that Sn-3.0Ag-0.5Cu-0.1Ni/Cu-15Zn solder joints still present higher shear strength after aging at 150 °C. The weakened shear strength in Sn-3.0Ag-0.5Cu-0.1Ni/Cu solder joints is due to stress accumulation in the interfacial (Cu,Ni)₆Sn₅ compound induced by the phase transformation from a high-temperature hexagonal structure (η-Cu₆Sn₅) to a low-temperature monoclinic structure (η'-Cu₆Sn₅). However, doping small amounts of Zn into (Cu,Ni)₆(Sn,Zn)₅ can inhibit the phase transformation during thermal aging and maintain strong shear strength. These experiments demonstrate that Sn-3.0Ag-0.5Cu-0.1Ni/Cu-15Zn solder joints can act as a stable connection in the micro-electronic packaging of most electronic products at their average working temperatures.     

Interfacial reactions and mechanical properties between Sn-4.0Ag-0.5Cu and Sn-4.0Ag-0.5Cu-0.05Ni-0.01Ge lead-free solders with the Au/Ni/Cu substrate

Sn-4.0Ag-0.5Cu (SAC) and Sn-4.0Ag-0.5Cu-0.05Ni-0.01Ge (SACNG) lead-free solders reacting with the Au/Ni/Cu multi-layer substrate were investigated in this study. All reaction couples were reflowed at 240 and 255 °C for a few minutes and then aged at 150 °C for 100-500 h. The (Cu, Ni, Au)₆Sn₅ phase was formed by reflowing for 3 min at the interface. If the reflowing time was increased to 10 min, both (Cu, Ni, Au)₆Sn₅ and (Ni, Cu, Au)₃Sn₄ phases formed at the interface. The AuSn₄ phase was found in the solder for all reaction couples. An addition of Ni and Ge to the solder does not significantly affect the IMC formation. After a long period of heat-treatment, the thickness of the (Cu, Ni, Au)₆Sn₅ and (Ni, Cu, Au)₃Sn₄ phases increased and the intermetallic compounds (IMCs) growth mechanism obeyed the parabolic law and the IMC growth mechanism was diffusion-controlled. The mechanical strengths for both the soldered joints decreased with increasing thermal aging time. The SACNG/Au/Ni/Cu couple had better mechanical strength than that in the SAC/Au/Ni/Cu couple.     

Sequential interfacial intermetallic compound formation of Cu6Sn5 and Ni3Sn4 between Sn-Ag-Cu solder and ENEPIG substrate during a reflow process

The interfacial reactions between Sn-3.0 wt.% Ag-0.5 wt.% Cu solder and an electroless nickel-electroless palladium-immersion gold (ENEPIG) substrate were investigated. After initial reflowing, discontinuous polygonal-shape (Cu,Ni)₆Sn₅ intermetallic compounds (IMCs) formed at the interface. During reflowing for up to 60 min, the interfacial IMCs were sequentially changed in the following order: discontinuous (Cu,Ni)₆Sn₅, (Cu,Ni)₆Sn₅ and (Ni,Cu)₃Sn₄, and embedded (Cu,Ni)₆Sn₅ in (Ni,Cu)₃Sn₄. The interfacial product variation resulted from the preferential consumption of Cu atoms within the solder and continuous Ni diffusion from the Ni(P) layer.     

Effect of rare earth metal Ce addition to Sn-Ag solder on interfacial reactions with Cu substrate

The effect of adding a small amount of rare earth cerium (Ce) element to low Ag containing Sn-1wt%Ag Pb-free solder on its interfacial reactions with Cu substrate was investigated. The growth of intermetallic compounds (IMCs) between three Sn-1Ag-xCe solders with different Ce contents and a Cu substrate was studied and the results were compared to those obtained for the Ce-free Sn-1Ag/Cu systems. In the solid-state reactions of the Sn-1Ag(-xCe)/Cu solder joints, the two IMC layers, Cu₆Sn₅ and Cu₃Sn, grew as aging time increased. Compared to the Sn-1Ag/Cu joint, the growth of the Cu₆Sn₅ and Cu₃Sn layers was depressed for the Ce-containing Sn-1Ag-xCe/Cu joint. The addition of Ce to the Sn-Ag solder reduced the growth of the interfacial Cu-Sn IMCs and prevented the IMCs from spalling from the interface. The evenly-distributed Ce elements in the solder region blocked the diffusion of Sn atoms to the interface and retarded the growth of the interfacial IMC layer.     

Pb-free solders for flip-chip interconnects

A variety of lead-free solder alloys were studied for use as flip-chip interconnects including Sn-3.5Ag, Sn-0.7Cu, Sn-3.8Ag-0.7Cu, and eutectic Sn-37Pb as a baseline. The reaction behavior and reliability of these solders were determined in a flip-chip configuration using a variety of under-bump metallurgies (TiW/Cu, electrolytic nickel, and electroless Ni-P/Au). The solder micro-structure and intermetallic reaction products and kinetics were determined. The Sn-0.7Cu solder has a large grain structure and the Sn-3.5Ag and Sn-3.8Ag-0.7Cu have a fine lamellar two-phase structure of tin and Ag₃Sn. The intermetallic compounds were similar for all the lead-free alloys. On Ni, Ni₃Sn₄ formed and on copper, Cu₆Sn₅Cu₃Sn formed. During reflow, the intermetallic growth rate was faster for the lead-free alloys, compared to eutectic tin-lead. In solidstate aging, however, the interfacial intermetallic compounds grew faster with the tinlead solder than for the lead-free alloys. The reliability tests performed included shear strength and thermomechanical fatigue. The lower strength Sn-0.7Cu alloy also had the best thermomechanical fatigue behavior. Failures occurred near the solder/intermetallic interface for all the alloys except Sn-0.7Cu, which deformed by grain sliding and failed in the center of the joint. Based on this study, the optimal solder alloy for flip-chip applications is identified as eutectic Sn-0.7Cu. Editor’s Note: A hypertext-enhanced version of this article can be found at www.tms.org/pubs/journals/JOM/0106/Frear-0106.html For more information, contact D.R. Frear, Interconnect Systems Laboratories, Motorola, Tempe, AZ 85284; (480) 413-6655; fax (480) 413-4511; e-mail darrel.frear@motorola.com.     

Sn-0.3Ag-0.7Cu-xSb无铅钎料润湿性

研究了微量Sb元素对Sn-0.3Ag-0.7Cu无铅钎料润湿性的影响,采用润湿平衡法探讨了Sn-0.3Ag-0.7Cu-xSb钎料在不同氛围和不同钎剂条件下的润湿性能.结果表明,微量的Sb元素可以显著提高Sn-0.3Ag-0.7Cu无铅钎料润湿性.在氮气氛围条件下,Sn-0.3Ag-0.7Cu-xSb钎料的润湿性得到显著改善,主要基于氮气氛围减小熔融钎料的氧化.辅助不同的钎剂,钎料的润湿性差异较大,选择合适的钎剂可以明显提高Sn-0.3Ag-0.7Cu-xSb钎料的润湿性.     

Sn-Ag-Cu and Sn-Cu solders: Interfacial reactions with platinum

The interfacial reaction and intermetallic formation at the interface between tin solders containing a small amount of copper with platinum were investigated in this study. Sn-0.7Cu and Sn-1.7Cu solders were reacted with platinum by dipping Pt/Ti/Si specimens into the molten solder at 260°C. Sn-3.8Ag-0.7Cu solder was reacted with platinum by reflowing solder paste on a Pt/Ti/Si substrate at 250°C. PtSn₄ intermetallic formed in all specimens while Cu₆Sn₅ interfacial intermetallic was not observed at the solder/platinum interfaces in any specimens. A parabolic relationship existed between the thickness of the Pt-Sn intermetallic and reaction time, which indicates the intermetallic formation in the solder/platinum interface is diffusion controlled. For more information, contact Young-Ho Kim, Hanyang University, Department of Materials Engineering, Seoul, 133-791, Korea; e-mail kimyh@hanyang.ac.kr.     

Growth Behavior of Intermetallic Compounds at SnAgCu/Ni and Cu Interfaces

The growth behavior of reaction-formed intermetallic compounds (IMCs) at Sn3.5Ag0.5Cu/Ni and Cu interfaces under thermal-shear cycling conditions was investigated. The results show that the morphology of (Cu _x Ni_1–x )₆Sn₅ and Cu₆Sn₅ IMCs formed both at Sn3.5Ag0.5Cu/Ni and Cu interfaces gradually changed from scallop-like to chunk-like, and different IMC thicknesses developed with increasing thermal-shear cycling time. Furthermore, Cu₆Sn₅ IMC growth rate at the Sn3.5Ag0.5Cu/Cu interface was higher than that of (Cu _x Ni_1–x )₆Sn₅ IMC under thermal-shear cycling. Compared to isothermal aging, thermal-shear cycling led to only one Cu₆Sn₅ layer at the interface between SnAgCu solder and Cu substrate after 720 cycles. Moreover, Ag₃Sn IMC was dispersed uniformly in the solder after reflow. The planar Ag₃Sn formed near the interface changed remarkably and merged together to large platelets with increasing cycles. The mechanism of formation of Cu₆Sn₅, (Cu _x Ni_1–x )₆Sn₅ and Ag₃Sn IMCs during thermal-shear cycling process was investigated.     

Influence of rare earth Ce addition on the microstructure,properties and soldering reaction of pure Sn

The influence of trace rare earth (RE) Ce addition on the microstructure, melting point and wettability of pure Sn as well as on the soldering reactions in Sn-xCe/Cu(Ni) solder joints was investigated. In bulk Sn-xCe solders, large β-Sn grains were observed with the Ce addition less than 0.2 wt%; while the β-Sn grain size decreased markedly when the Ce addition was 0.2 wt%, resulting in a refined microstructure. The addition of trace RE Ce had little effect on the melting temperature of the solders. Smaller wetting angles of Sn-xCe solders on both Cu and Ni substrates were measured when the samples were reflowed at a higher temperature. The Sn-0.2Ce solder owned the best wettability on Cu substrate. Scallop-like Cu₆Sn₅ intermetallic compound (IMC) grains formed at the Sn-xCe/Cu interfaces, while a continuous Ni₃Sn₄ IMC layer formed at each Sn-xCe/Ni interface. With the increase of Ce addition, the interfacial IMC grain size and the interfacial IMC layer thickness on both Cu and Ni substrates decreased gradually. The activity of Sn was lowered with the Ce addition, which depressed the growth of the interfacial IMC. In the current study, the Ce addition of 0.2 wt% exhibits the optimized performance.     

Microstructural evolution of intermetallic compounds in Sn–3.5Ag–X (X = 0, 0.75Ni, 1.0Zn and 1.5In)/Cu solder joints during liquid aging

In this paper, the microstructural evolution of IMCs in Sn–3.5Ag–X (X = 0, 0.75Ni, 1.0Zn, 1.5In)/Cu solder joints and their growth mechanisms during liquid aging were investigated by microstructural observations and phase analysis. The results show that two-phase (Ni₃Sn₄ and Cu₆Sn) IMC layers formed in Sn–3.5Ag–0.75Ni/Cu solder joints during their initial liquid aging stage (in the first 8 min). While after a long period of liquid aging, due to the phase transformation of the IMC layer (from Ni₃Sn₄ and Cu₆Sn phases to a (Cu, Ni)₆Sn₅ phase), the rate of growth of the IMC layer in Sn–3.5Ag–0.75Ni/Cu solder joints decreased. The two Cu₆Sn₅ and Cu₅Zn₈ phases formed in Sn–3.5Ag–1.0Zn/Cu solder joints during the initial liquid aging stage and the rate of growth of the IMC layers is close to that of the IMC layer in Sn–3.5Ag/Cu solder joints. However, the phase transformation of the two phases into a Cu–Zn–Sn phase speeded up the growth of the IMC layer. The addition of In to Sn–3.5Ag solder alloy resulted in Cu₆(Sn_x,In_1?x)₅ phase which speeded up the growth of the IMC layer in Sn–3.5Ag–1.5In/Cu solder joint.     

Intermetallic compound growth suppression at high temperature in SAC solders with Zn addition on Cu and Ni-P substrates

The effect of adding 0.5-1.5 wt.% Zn to Sn-3.8Ag-0.7Cu (SAC) solder alloy during reflow and solid state ageing has been investigated. In particular, the role of the Zn addition in suppressing interfacial Intermetallic Compound (IMC) growth on Cu and Ni-P substrates has been determined. Solder-substrate couples were aged at 150 °C and 185 °C for 1000 h. In the case of 0.5-1.0 wt.% Zn on Cu substrate, Cu₃Sn IMC was significantly suppressed and the morphology of Cu₆Sn₅ grains was changed, leading to suppressed Cu₆Sn₅ growth. In the SAC-1.5Zn/Cu substrate system a Cu₅Zn₈ IMC layer nucleated at the interface followed by massive spalling of the layer into the solder, forming a barrier layer limiting Cu₆Sn₅ growth. On Ni-P substrates the (Cu,Ni)₆Sn₅ IMC growth rate was suppressed, the lowest growth rate being found in the SAC-1.5Zn/Ni-P system. In all cases the added Zn segregated to the interfacial IMCs so that Cu₆Sn₅ became (Cu,Zn)₆Sn₅ and (Cu,Ni)₆Sn₅ became (Ni,Cu,Zn)₆Sn₅. The effect of Zn concentration on undercooling, wetting angles and IMC composition changes during ageing are also tabulated, and a method of incorporating Zn into the solder during reflow without compromising solder paste reflow described.     

稀土Pr对低银Sn-0.3Ag-0.7Cu-0.5Ga钎料蠕变行为影响的研究

为进一步促进电子封装用低银无铅钎料的发展,本文采用纳米压痕法研究了新型含Pr低银Sn-0.3Ag-0.7Cu-0.5Ga (SAC-Ga)钎料显微组织与蠕变性能之间的关系。结果表明,SAC-Ga、SAC-Ga-0.06Pr、SAC-Ga-0.5Pr三种钎料的蠕变位移分别为1717 nm、1144 nm、1472 nm;稀土Pr可通过细化Cu₆Sn₅金属间化合物并促使其均匀分布从而明显提高SAC-Ga钎料的蠕变强度;与SAC-Ga-0.06Pr钎料相比,SAC-Ga-0.5Pr由于过量稀土Pr的表面氧化而导致其蠕变强度有所下降。此外,本文采用Dorn模型研究了含Pr的SAC-Ga钎料的室温蠕变行为并计算了对应的钎料蠕变应力指数n;阐明了Pr对SAC-Ga钎料蠕变强度的强化机理,即当位错遇到细小且均匀分布的Cu₆Sn₅ 金属间化合物时,位错移动只能采用绕过机制,从而提高了含Pr低银钎料的抗蠕变性能。     

Thermal reliabilities of Sn-0.5Ag-0.7Cu-0.1Al2O3/Cu solder joint

The effects of trace addition of Al₂O₃ nanoparticles (NPs) on thermal reliabilities of Sn-0.5Ag-0.7Cu/Cu solder joints were investigated. Experimental results showed that trace addition of Al₂O₃ NPs could increase the isotheraml aging (IA) and thermal cyclic (TC) lifetimes of Sn-0.5Ag-0.7Cu/Cu joint from 662 to 787 h, and from 1597 to 1824 cycles, respectively. Also, trace addition of Al₂O₃ NPs could slow down the shear force reduction of solder joint during thermal services, which was attributed to the pinning effect of Al₂O₃ NPs on hindering the growth of grains and interfacial intermetallic compounds (IMCs). Theoretically, the growth coefficients of interfacial IMCs in IA process were calculated to be decreased from 1.61×10^-10 to 0.79×10^-10 cm²/h in IA process, and from 0.92×10^-10 to 0.53×10^-10 cm²/h in TC process. This indicated that trace addition of Al₂O₃ NPs can improve both IA and TC reliabilities of Sn-0.5Ag- 0.7Cu/Cu joint, and a little more obvious in IA reliability.     

Effects of Ga,Al, Ag,and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solder

An orthogonal method was used to evaluate the effects of Ga, Al, Ag, and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solders by wetting balance method. The results show that the optimal loading of Ga, Al, Ag, and Ce was 0.2 wt.%, 0.002 wt.%, 0.25 wt.%, and 0.15 wt.%, respectively. Intermetallic compounds (IMCs) formed at the interface between Sn-9Zn-0.2Ga-0.002Al-0.25Ag-0.15Ce solder and Cu substrate were investigated by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) analysis. The SEM images illustrate that the IMCs can be divided into two portions from the substrate side to the solder side: a planar Cu₅Zn₈ layer and an additional continuous scallop-like AgZn₃ layer. The EDS analysis also shows that Ga segregates in the solder abutting upon the interface. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) of the surface components of Sn-9Zn-0.2Ga-0.002Al-0.25Ag-0.15Ce solder indicate that Al aggregates at the surface in the form of Al₂O₃ protective film, which prevents the further oxidation of the solder surface. On the other hand, Ce aggregates at the subsurface, which may reduce the surface tension of the solder and improve the wettability in consequence.     

Ni segregation in the interfacial (Cu,Ni)6Sn5 intermetallic layer of Sn-0.7Cu-0.05Ni/Cu ball grid array (BGA) joints

Ni segregation in the interfacial (Cu,Ni)₆Sn₅ intermetallic layer of Sn-0.7Cu-0.05Ni/Cu BGA solder joints was investigated by using synchrotron micro X-ray fluorescence (XRF) analysis and synchrotron X-ray diffraction (XRD). Compared to Sn-0.7Cu/Cu BGA joints, Ni containing solder show suppressed Cu₃Sn growth in both reflow and annealed conditions. In as-reflowed Sn-0.7Cu-0.05Ni/Cu BGA joints, Ni was relatively homogenously distributed within interfacial (Cu,Ni)₆Sn₅. During subsequent annealing, the diffusion of Ni in Cu₆Sn₅ was limited and it remained concentrated adjacent the Cu substrate where it contributes to the suppression of Cu₃Sn formation at the interface between the Cu substrate and Cu₆Sn₅ intermetallics.     

Bi对Sn-0.3Ag-0.7Cu无铅钎料熔点及润湿性能的影响

研究了添加适量的Bi元素对低银型Sn-0．3Ag-0．7Cu无铅钎料合金性能的影响,应用差示扫描量热仪和SAT-5100型润湿平衡仪对Sn-0．3Ag-0．7Cu·xBi（x=0.1,3,4．5）钎料的熔点、润湿性能作了对比试验分析。结果表明,一定量Bi元素的加入可以降低Sn-0．3Ag-0．7Cu钎料合金的熔点,并改善其润湿性能。但过多的Bi元素会导致钎料的液固相线温度差增大,塑性下降,造成焊点剥离缺陷。综合考虑得到Sn-0．3Ag-0．7Cu-3．0Bi无铅钎料具有最佳的综合性能。     

热循环对Sn58Bi(纳米Ti)/Cu焊点界面与性能影响

为了改善Sn-58Bi低温钎料的性能,通过在Sn-58Bi低温钎料中添加质量分数为0.1%的纳米Ti颗粒制备了Sn-58Bi-0.1Ti纳米增强复合钎料。在本文中,研究了纳米Ti颗粒的添加对-55～125 _^oC热循环过程中Sn-58Bi/Cu焊点的界面金属间化合物(IMC)生长行为的影响。研究结果表明：回流焊后,在Sn-58Bi/Cu焊点和Sn-58Bi-0.1Ti/Cu焊点的界面处都形成一层扇贝状的Cu₆Sn₅ IMC层。在热循环300次后,在Cu₆Sn₅/Cu界面处形成了一层Cu₃Sn IMC。Sn-58Bi/Cu焊点和Sn-58Bi-0.1Ti/Cu焊点的IMC层厚度均和热循环时间的平方根呈线性关系。但是,Sn-58Bi-0.1Ti/Cu焊点的IMC层厚度明显低于Sn-58B/Cu焊点,这表明纳米Ti颗粒的添加能有效抑制热循环过程中界面IMC的过度生长。另外计算了这两种焊点的IMC层扩散系数,结果发现Sn-58Bi-0.1Ti/Cu焊点的IMC层扩散系数(整体IMC、Cu₆Sn₅和Cu₃Sn IMC)明显比Sn-58Bi/Cu焊点小,这在一定程度上解释了Ti纳米颗粒对界面IMC层的抑制作用。     

Effect of adding 1 wt% Bi into the Sn–2.8Ag–0.5Cu solder alloy on the intermetallic formations with Cu-substrate during soldering and isothermal aging

Intermetallic compound (IMC) formations of Sn–2.8Ag–0.5Cu solder with additional 1 wt% Bi were studied for Cu-substrate during soldering at 255 °C and isothermal aging at 150 °C. It was found that addition of 1 wt% Bi into the Sn–2.8Ag–0.5Cu solder inhibits the excessive formation of intermetallic compounds during the soldering reaction and thereafter in aging condition. Though the intermetallic compound layer was Cu₆Sn₅, after 14 days of aging a thin Cu₃Sn layer was also observed for both solders. A significant increase of intermetallic layer thickness was observed for both solders where the increasing tendency was lower for Bi-containing solder. After various days of aging, Sn–2.8Ag–0.5Cu–1.0Bi solder gives comparatively planar intermetallic layer at the solder–substrate interface than that of the Sn–2.8Ag–0.5Cu solder. The formation of intermetallic compounds during aging for both solders follows the diffusion control mechanism and the diffusion of Cu is more pronounced for Sn–2.8Ag–0.5Cu solder. Intermetallic growth rate constants for Sn–2.8Ag–0.5Cu and Sn–2.8Ag–0.5Cu–1.0Bi solders were calculated as 2.21 × 10⁻¹⁷ and 1.91 × 10⁻¹⁷ m²/s, respectively, which had significant effect on the growth behavior of intermetallic compounds during aging.     

Development of high strength Sn-0.7Cu solders with the addition of small amount of Ag and In

Nowadays, a major concern of Sn-Cu based solder alloys is focused on continuously improving the comprehensive properties of solder joints formed between the solders and substrates. In this study, the influence of Ag and/or In doping on the microstructures and tensile properties of eutectic Sn-0.7Cu lead free solder alloy have been investigated. Also, the effects of temperature and strain rate on the mechanical performance of Sn-0.7Cu, Sn-0.7Cu-2Ag, Sn-0.7Cu-2In and Sn-0.7Cu-2Ag-2In solders were investigated. The tensile tests showed that while the ultimate tensile strength (UTS) and yield stress (YS) increased with increasing strain rate, they decreased with increasing temperature, showing strong strain rate and temperature dependence. The results also revealed that with the addition of Ag and In into Sn-0.7Cu, significant improvement in YS (∼255%) and UTS (∼215%) is realized when compared with the other commercially available Sn-0.7 wt. % Cu solder alloys. Furthermore, the Sn-0.7Cu-2Ag-2In solder material developed here also exhibits higher ductility and well-behaved mechanical performance than that of eutectic Sn-0.7Cu commercial solder. Microstructural analysis revealed that the origin of change in mechanical properties is attributed to smaller β-Sn dendrite grain dimensions and formation of new inter-metallic compounds (IMCs) in the ternary and quaternary alloys.     

SAC0307-xNi/Ni焊点的IMC及镍镀层的消耗

利用扫描电镜(SEM)对焊点SAC0307/Ni(Sn-O.3Ag-0.7Cu/Ni)和SAC0307-0.05Ni/Nj(Sn-O.3Ag-0.7Cu-0.05 Ni/Ni)经过180℃老化后的界面金属问化合物(IMC)的微观结构及镍镀层的消耗进行了研究.结果表明,回流焊后,SAC0307/Ni和SAC0307-O.05Ni/Ni焊点的IMC层均为(Cu_(1-x)Ni_x)_6Sn_5,且随着老化时间的延长,IMC层的厚度均逐渐增加,化合物类型没有变化,但IMC的化学组成有所改变.SAC0307-0.05Ni/Ni焊点中IMC层形貌为蠕虫状,厚度比不加镍时有所降低.回流焊后两种钎料焊盘的镍层消耗几乎相同,但老化384h后SAC0307/Ni的焊盘镍层的剩余厚度明显比SAC0307-0.05Ni/Ni的小.因此,钎料中添加适量的镍可以有效地降低焊盘镍层在时效过程中的消耗速率,即显著提高镍焊盘的抗老化能力.

Abstract：

The micrestmcture of interfacial IMC and the consumption of Ni layer for SAC0307/Ni ( Sn-0.3Ag-0.7Cu/Ni ) soldered joint and SAOY307-0.05Ni/Ni (Sn-O. 3Ag-0.7Cu-0.05Ni/Ni) soldered joint after aging at 180℃ were studied by scanning electron microscope( SEM ). The results indicated that the IMC layer of SAC0307/Ni and SAC0307-0.05Ni/Ni are both (Cu_(1-x),Ni_x)_6Sn_5 after reflow soldering. With the increasing of aging time, the thickness of IMC layer increases gradually, the type of IMC is not changed, but the chemical composition changes. The morphology of IMC is stormshaped and the thickness of IMC is much thinner when SAC0307 solder added 0. 05 % Ni is used. The consumption of Ni layer is nearly the same using both solders "after the first time reflow soldering, but the residual thickness of the Ni layer in SACO307/Ni solder is thinner than that in SAC0307-0.05Ni/Ni after aging for 384 h. So solders with a little Ni element can decrease the consumption rate of Ni layer effectively during aging, that is, the aging-resistant abihty of Ni pad is improved obviously.