Metal ion adsorption behavior of lignocellulosic fiber–ethylene vinyl acetate composites

This study describes the applicability of lignocellulosic fiber dispersed in ethylene vinyl acetate (EVA) to adsorb Pb(II), Cr(III), and Cr(VI) ions in aqueous solutions. Water absorption studies revealed that metal‐ion uptake does not only take place on the surface of the adsorbent but ions can also diffuse into the composite. The adsorption of the metal ions under different experimental conditions was studied. Solute concentration, pH, and contact time were used to assess the adsorption capacity and efficiency. The amount of metal adsorbed increased to 7 mg/g with an increase in solute concentration but compromising the efficiency. Adsorption equilibrium was reached after 3 h, when the maximum lead adsorption was above 80%. The optimum pH for the adsorption of Pb(II) and Cr(III) was 6.5, and pH 2.5 was used for the adsorption of Cr(VI). Competitive adsorption revealed the order of adsorption to be: Pb(II) > Cr(VI) > Cr(III). POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Hexafunctional poly(propylene glycol) based hydrogels for the removal of heavy metal ions

Two types of degradable poly(propylene glycol) (PPG) hydrogels that are suitable for the absorption of heavy metals have been presented. The PPG‐O‐P(O)Cl₂ fragments obtained by treating hexafunctional PPG with phosphorous oxychloride (POCl₃) react with 1,3‐propanediamine (PDA; Gel‐1 ) or PDA together with 1,2‐ethanedithiol ( Gel‐2 ), to yield cross‐linked and water‐swellable hydrogels in a one‐pot method. This protocol for the fabrication of PPG hydrogels exhibits promising advantages over prior methods including a short reaction time, mass‐production, easy separation, and high yield. A series of heavy metal ions were employed to test the adsorptive properties of the hydrogels. Gel‐2 shows better adsorption capacity than Gel‐1 for all the metal ions and the metal ions adsorption efficiency of the two types of hydrogels is in the order of Fe(III) > Pb(II) > Cd(II) > Zn(II) > Cu(II) > Ni(II) > Co(II) > Hg(II). The amounts of metal ions adsorbed increases with metal ion concentration and hydrogel dosage, but decreases with temperature. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40610.     

A modified cellulose adsorbent for the removal of nickel(II) from aqueous solutions

A series of adsorption studies was carried out on a glycidyl methacrylate‐ modified cellulose material functionalised with imidazole (Cellulose‐g‐GMA‐Imidazole) to assess its capacity in the removal of Ni(II) ions from aqueous solution. The study sought to establish the effect of a number of parameters on the removal of Ni(II) from solution by the Cellulose‐g‐GMA‐Imidazole. In particular, the influence of initial metal concentration, contact time, solution temperature and pH were assessed. The studies indicated a Ni(II) uptake on the Cellulose‐g‐GMA‐Imidazole sorbent of approximately 48 mg g^?1 of nickel from aqueous solution. The adsorption process fitted the Langmuir model of adsorption and the binding process was mildly endothermic. The kinetics of the adsorption process indicated that nickel uptake occurred within 400 min and that pseudo‐second order kinetics best describe the overall adsorption process. Nickel(II) adsorption, recovery and re‐adsorption studies indicated that at highly acidic pH values the adsorbent material becomes unstable, but in the range pH 3–6, the adsorbent is stable and shows limited but significant Ni(II) recovery and re‐adsorption capability. Copyright © 2006 Society of Chemical Industry     

Adsorption of copper(II), cobalt(II), and iron(III) ions from aqueous solutions on poly(ethylene terephthalate) fibers

The adsorption behavior of poly(ethylene terephthalate) (PET) fibers towards copper(II), cobalt(II), and iron(III) ions in aqueous solutions was studied by a batch equilibriation technique. Influence of treatment time, temperature, pH of the solution, and metal ion concentration on the adsorption were investigated. Adsorption values for metal ion intake followed the following order: Co(II) > Cu(II) > Fe(III). One hour of adsorption time was found sufficient to reach adsorption equilibrium for all the ions. The rate of adsorption was found to decrease with the increase in the temperature. Langmuir adsorption isoterm curves were found to be significant for all the ions studied. The heat of adsorption values were calculated as −5, −2.8, and −3.6 kcal/mol for Cu(II), Co(II), and Fe(III) ions, respectively. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1935–1939, 1998     

Synthesis,characterization, and catalytic activity of 4 mol % N,N′‐methylene bisacrylamide crosslinked poly(acrylic acid)–metal complexes

The metal‐ion complexation behavior and catalytic activity of 4 mol % N,N′‐methylene bisacrylamide crosslinked poly(acrylic acid) were investigated. The polymeric ligand was prepared by solution polymerization. The metal‐ion complexation was studied with Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), and Zn(II) ions. The metal uptake followed the order: Cu(II) > Cr(III) > Mn(II) > Co(II) > Fe(III) > Zn(II) > Ni(II). The polymeric ligand and the metal complexes were characterized by various spectral methods. The catalytic activity of the metal complexes were investigated toward the hydrolysis of p‐nitrophenyl acetate (NPA). The Co(II) complexes exhibited high catalytic activity. The kinetics of catalysis was first order. The hydrolysis was controlled by pH, time, amount of catalyst, and temperature. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 272–279, 2004     

Investigation of Heavy Metal Ion Adsorption Characteristics of Poly(N,N Dimethylamino Ethylmethacrylate) Hydrogels

Abstract

In this study, Poly(N,N dimethyl‐amino ethylmethacrylate) (Poly(DMAEMA)) hydrogels with varying compositions were prepared in the form of rods by irradiating ternary mixtures of N,N‐dimethylamino ethylmethacrylate/ethyleneglycoldimethacrylate/water with gamma rays at ambient temperature. Swelling studies of poly (DMAEMA) hydrogels were performed at different pH values and maximum swelling values reached at pH 2. The adsorption characteristics of Pb(II), Cd(II), Ni(II), Zn(II), Cu(II), and Co(II) ions to poly(N,N dimethylamino ethylmethacrylate) hydrogels were investigated by a batch process. The order of affinity based on amount of metal ion uptake was found as follows: Cu(II)>Zn(II)?Co(II)>Pb(II) >> Ni(II)>Cd(II). In the adsorption studies of Cu(II), Zn(II), Co(II), Pb(II), Ni(II), and Cd(II) ions the Langmuir type adsorption isotherms were observed for all gel systems.     

Determination of the competitive adsorption of heavy metal ions on poly(n‐vinyl‐2‐pyrrolidone/acrylic acid) hydrogels by differential pulse polarography

Poly(N‐vinyl‐2‐pyrrolidone) and poly(N‐vinyl‐2‐pyrrolidone/acrylic acid) hydrogels were prepared by gamma irradiation for the removal of heavy metal ions (i.e., lead, copper, zinc, and cadmium) from aqueous solutions containing different amounts of these ions (2.5–10 mg/L) and at different pH values (1–13). The observed affinity order in adsorption of these metal ions on the hydrogels was Zn(II) > Pb(II) > Cu(II) > Cd(II) under competitive conditions. The optimal pH range for the heavy metal ions was from 7 to 9. The adsorption of the heavy metal ions decreased with increasing temperature in both water and synthetic seawater conditions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2013–2018, 2003     

PREPARATION AND ADSORPTION PROPERTIES OF THE POLYSTYRENE RESIN HAVING DIETHYLENETRIAMINE-N,N′- BIS(METHYLENEPHOSPHONATE) GROUP

Styrene-divinylbenzene copolymer beads containing diethylenetriamine-N,N′-bis(methylenephosphonate) group have been synthesized. The adsorption properties, of the present resin for some trivalent and bivalent metal ions have been examined. The selectivity sequence of the present resin at pH lower than 2.0 is as follows: Ga(III)> A1(III)> Sm(III)>Cu(II)>Co(II)>Zn(II)>Ca(II). The present resin reveals remarkable selectivity for the trivalent metal ions. The selective concentration of In(III) Ga(III) and Sm(III) from an acidic aqueous solution has been demonstrated by using a column of the present resin.     

Application of anionic acrylamide‐based hydrogels in the removal of heavy metals from waste water

Crosslinked acrylamide (AM) and 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) homopolymers and copolymers were prepared by free radical solution polymerization using N,N′‐methylenebisacrylamide as the crosslinker. The chemical structures of hydrogels were characterized by FTIR analysis and the results were consistent with the expected structures. These hydrogels were used for the separation of Cd(II), Cu(II), and Fe(III) ions from their aqueous solutions. The influence of the uptake conditions such as pH, time and initial feed concentration on the metal ion binding capacity of hydrogel was also tested. The selectivity of the hydrogel towards the different metal ions tested was Cd(II) > Cu(II) > Fe(III). It was observed that the specific interaction between metal ions and ionic comonomers in the hydrogel affected the metal binding capacity of the hydrogel. The recovery of metal ions was also investigated in acid media. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Acrylonitrile/acrylamidoxime/2‐acrylamido‐2‐ methylpropane sulfonic acid‐based hydrogels: Synthesis,characterization and their application in the removal of heavy metals

Crosslinked acrylonitrile/acrylamidoxime/2‐acrylamido‐2‐methylpropane sulfonic acid (AN/AAx/AMPS)‐based hydrogels were prepared by free radical crosslinking solution polymerization technique. The chemical structures of the hydrogels were characterized by FT‐IR analysis. The morphology of the dry hydrogel sample was examined by scanning electron microscope (SEM). These hydrogels were used for the removal of Cd(II), Cu(II), and Fe(III) ions from their aqueous solutions. The influence of the uptake conditions such as pH, time and initial feed concentration on the metal ion binding capacity of hydrogel was also tested. The selectivity of the hydrogel towards the different metal ions tested was arranged in the order of Cd(II) > Fe(III) > Cu(II). It was observed that the specific interaction between metal ions and ionic comonomer in the hydrogel affected the metal binding capacity of the hydrogel. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of amidoximated polyester fiber and competitive adsorption of some heavy metal ions from aqueous solution onto this fiber

In this study, a fibrous adsorbent containing amidoxime groups was prepared by graft copolymerization of acrylonitrile (AN) onto poly(ethylene terephthalate) (PET) fibers using benzoyl peroxide (Bz₂O₂) as initiator in aqueous solution, and subsequent chemical modification of cyano groups by reaction with hydroxylamine hydrochloride in methanol. The grafted and modified fibers were characterized by FTIR, TGA, SEM, and XRD analysis. The crystallinity increased, but thermal stability decreased with grafting and amidoximation. The removal of Cu(II), Ni(II), Co(II), Pb(II), and Cd(II) ions from aqueous solution onto chelating fibers were studied using batch adsorption method. These properties were investigated under competitive conditions. The effects of the pH, contact time, and initial ion concentration on the removal percentage of ions were studied. The results show that the adsorption rate of metal ions followed the given order Co(II) > Pb(II) > Cd(II) > Ni(II) > Cu(II). The percentage removal of ions increased with initial ion concentration, shaking time, and pH of the medium. Total metal ion removal capacity was 49.75 mg/g fiber on amidoximated fiber. It was observed that amidoximated fibers can be regenerated by acid without losing their activity, and it is more selective for Pb(II) ions in the mixed solution of Pb‐Cu‐Ni–Co‐Cd at pH 4. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The effect of crosslinking on the adsorption behavior of copper (II) onto poly(2‐hydroxy‐4‐acryloyloxybenzophenone)

The adsorption behavior of Cu(II) ions onto poly(2‐hydroxy‐4‐acryloyloxybenzophenone), polymer I, and onto poly(2‐hydroxy‐4‐acryloyloxybenzophenone) crosslinked with different amounts of divinylbenzene (DVB), polymers II, III, and IV, in aqueous solutions was investigated using batch adsorption experiments as a function of contact time, pH, and temperature. The amount of metal ion uptake of the polymers was determined by using atomic absorption spectrometry (AAS) and the highest uptake was achieved at pH 7.0 and by using perchlorate as an ionic strength adjuster for polymers I, II, III, and IV. Results revealed that the adsorption capacity (q_e and Q_m) of Cu(II) ions decreases with increasing crosslinking due to the decrease of chelation sites. In addition, the rate of adsorption (k₂) of Cu(II) ions decreases with the increase of crosslinking because it becomes more difficult for Cu(II) ions to diffuse into the chelation sites. The isothermal behavior and the kinetics of adsorption of Cu(II) ions on these polymers with respect to the initial mass of the polymer and temperature were also investigated. The experimental data of the adsorption process was found to correlate well with the Langmuir isotherm model. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Chitosan‐grafted poly(hydroxyethyl methacrylate‐co‐glycidyl methacrylate) membranes for reversible enzyme immobilization

Epoxy group‐containing poly(hydroxyethyl methacrylate/glycidyl methacrylate), p(HEMA/GMA), membrane was prepared by UV initiated photopolymerization. The membrane was grafted with chitosan (CH) and some of them were chelated with Fe(III) ions. The CH grafted, p(HEMA/GMA), and Fe(III) ions incorporated p(HEMA/GMA)‐CH‐Fe(III) membranes were used for glucose oxidase (GOD) immobilization via adsorption. The maximum enzyme immobilization capacity of the p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes were 0.89 and 1.36 mg/mL, respectively. The optimal pH value for the immobilized GOD preparations is found to have shifted 0.5 units to more acidic pH 5.0. Optimum temperature for both immobilized preparations was 10°C higher than that of the free enzyme and was significantly broader at higher temperatures. The apparent K_m values were found to be 6.9 and 5.8 mM for the adsorbed GOD on p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes, respectively. In addition, all the membranes surfaces were characterized by contact angle measurements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3084–3093, 2007     

Adsorption of heavy‐metal ions on poly(ethylene imine)‐immobilized poly(methyl methacrylate) microspheres

Poly(methyl methacrylate) (PMMA) microspheres carrying poly(ethylene imine) (PEI) were prepared for the removal of heavy‐metal ions (copper, cadmium, and lead) from aqueous solutions with different amounts of these ions (50–600 mg/L) and different pH values (3.0–7.0). Ester groups in the PMMA structures were converted to imine groups in a reaction with PEI as a metal‐chelating ligand in the presence of NaH. The adsorption of heavy‐metal ions on the unmodified PMMA microspheres was very low [3.6 μmol/g for Cu(II), 4.6 μmol/g for Cd(II), and 4.2 μmol/g for Pb(II)]. PEI immobilization significantly increased the heavy‐metal adsorption [0.224 mmol/g for Cu(II), 0.276 mmol/g for Cd(II), and 0.126 mmol/g for Pb(II)]. The affinity order of adsorption (in moles) was Cd(II) > Cu(II) > Pb(II). The adsorption of heavy‐metal ions increased with increasing pH and reached a plateau value around pH 5.5. Their adsorption behavior was approximately described with the Langmuir equation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 197–205, 2001     

Electron Beam Grafted Polymer Adsorbent for Removal of Heavy Metal Ion from Aqueous Solution

Abstract

An electron beam grafted adsorbent was synthesized by post irradiation grafting of acrylonitrile (AN) on to a non‐woven thermally bonded polypropylene (PP) sheet using 2 MeV electron beam accelerator. The grafted poly(acrylonitrile) chains were chemically modified to convert a nitrile group to an amidoxime (AMO) group, a chelating group responsible for metal ion uptake from an aqueous solution. The effect of various experimental variables viz. dose, dose rate, temperature, and solvent composition on the grafting extent was investigated. PP grafted with the amidoxime group (AMO‐g‐PP) was tested for its suitability as an adsorbent for removal of heavy metal ions such as Co²⁺, Ni²⁺, Mn²⁺, and Cd²⁺ from aqueous solution. Langmuir and Freundlich adsorption models were used to investigate the type of adsorption of these ions. The adsorption capacities of the adsorbent for the metal ions were found to follow the order Cd²⁺>Co²⁺>Ni²⁺>Mn²⁺. The kinetics of adsorption of these ions indicated that the rate of adsorption of Cd²⁺ was faster than that of other ions studied.     

Adsorption of Cr(III), Ni(II), Zn(II), Co(II) ions onto phenolated wood resin

In this study, phenolated wood resin was used an adsorbent for the removal of Cr(III), Ni(II), Zn(II), Co(II) ions by adsorption from aqueous solution. The adsorption of metal ions from solution was carried at different contact times, concentrations and pHs at room temperature (25°C). For individual metal ion, the amount of metal ions adsorbed per unit weight of phenolated wood resin at equilibrium time increased with increasing concentration and pH. Also, when the amounts of metal ions adsorbed are compared to each other, it was seen that this increase was order of Cr(III) > Ni(II) > Zn(II) > Co(II). This increase was order of Cr(III) > Ni(II) > Co(II) > Zn(II) for commercial phenol–formaldehyde resin. Kinetic studies showed that the adsorption process obeyed the intraparticle diffusion model. It was also determined that adsorption isotherm followed Langmuir and Freundlich models. Adsorption isotherm obtained for commercial phenol–formaldehyde resin was consistent with Freundlich model well. Adsorption capacities from Langmuir isotherm for commercial phenol–formaldehyde resin were higher than those of phenolated wood resin, in the case of individual metal ions. Original adsorption isotherm demonstrated the monolayer coverage of the surface of phenolated wood resin. Adsorption kinetic followed the intraparticle diffusion model. The positive values of ΔG° determined using the equilibrium constants showed that the adsorption was not of spontaneous nature. It was seen that values of distribution coefficient (K_D) decreasing with metal ion concentration in solution at equilibrium (C_e) indicated that the occupation of active surface sites of adsorbent increased with metal ions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2838–2846, 2006     

Preparation and characterization of magnetic polymethylmethacrylate microbeads carrying ethylene diamine for removal of Cu(II), Cd(II), Pb(II), and Hg(II) from aqueous solutions

Magnetic polymethylmethacrylate (mPMMA) microbeads carrying ethylene diamine (EDA) were prepared for the removal of heavy metal ions (i.e., copper, lead, cadmium, and mercury) from aqueous solutions containing different amount of these ions (5–700 mg/L) and at different pH values (2.0–8.0). Adsorption of heavy metal ions on the unmodified mPMMA microbeads was very low (3.6 μmol/g for Cu(II), 4.2 μmol/g for Pb(II), 4.6 μmol/g for Cd(II), and 2.9 μmol/g for Hg(II)). EDA‐incorporation significantly increased the heavy metal adsorption (201 μmol/g for Cu(II), 186 μmol/g for Pb(II), 162 μmol/g for Cd(II), and 150 μmol/g for Hg(II)). Competitive adsorption capacities (in the case of adsorption from mixture) were determined to be 79.8 μmol/g for Cu(II), 58.7 μmol/g for Pb(II), 52.4 μmol/g for Cd(II), and 45.3 μmol/g for Hg(II). The observed affinity order in adsorption was found to be Cu(II) > Pb(II) > Cd(II) > Hg(II) for both under noncompetitive and competitive conditions. The adsorption of heavy metal ions increased with increasing pH and reached a plateau value at around pH 5.0. The optimal pH range for heavy‐metal removal was shown to be from 5.0 to 8.0. Desorption of heavy‐metal ions was achieved using 0.1 M HNO₃. The maximum elution value was as high as 98%. These microbeads are suitable for repeated use for more than five adsorption‐desorption cycles without considerable loss of adsorption capacity. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 81–89, 2000     

Adsorption of urokinase by polypropylene films with various amine groups

Polypropylene films with various amine groups were prepared by radiation‐induced grafting of glycidyl methacrylate (GMA) onto polypropylene (PP) films and the subsequent amination of poly‐GMA graft chains were examined. The physical and chemical properties of the GMA‐grafted PP film and the aminated PP film were investigated by IR, SEM, XPS, and TGA. The adsorption of urokinase for the PP films modified with various amine groups was examined under various conditions of different amine group contents and pH values. The adsorption of urokinase increased by increasing the amine group content. In the range of amine group content from 1.0 to 2.7 mmol/g, the adsorption of urokinase by the PP films modified with six kinds of amines was in the following order: trimethylamine > diethylenetriamine > triethylenetetraamine > ethylenediamine > dimethylamine > diethyleneamine. The adsorption amounts of urokinase by the PP film with the trimethylamine and triethylenetetraamine groups at pH 7.4 were higher than those at pH 9. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2851–2858, 2001     

Adsorption of some heavy metal ions from aqueous solutions on Nafion 117 membrane

Nafion 117 membrane was investigated for the removal of Ni(II), Co(II), Pb(II), Cu(II) and Ag(I) metal ions from their synthesized aqueous solutions. The different variables affecting the adsorption capacity of the membrane such as contact time, initial metal ion concentration in the feed solution, pH of the sorption medium and temperature of the solution were investigated on a batch sorption basis. The affinity of Nafion 117 membrane towards heavy metal ions was found to increase in the sequence of Cu(II), Ni(II), Co(II), Pb(II), and Ag(I) with adsorption equilibrium achieved after 30 min for all metal ions. Among all parameters, pH has the most significant effect on the adsorption capacity, particularly in the range of 3.1-5.9. The variation of temperature in the range of 25-65 °C was found to have no significant effect on the adsorption capacity. Nafion 117 membrane was found to have high stability combined with repeated regeneration ability and can be suggested for effective removal of heavy metal ions such as Cu(II), Ni(II) and Co(II) from aqueous solutions.     

Adsorption Behavior of Iminodiacetic Acid Type of Chelating Gel Prepared from Waste Paper

Abstract

Adsorption gel was prepared from waste recycled paper by immobilizing iminodiacetic acid (IDA) functional group by chemical modification. The gel exhibited good adsorption behavior for a number of metal ions viz. Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. The order of selectivity was found to be as follows: Cu(II)>Pb(II)>Fe(III)>Ni(II)～Cd(II)～Co(II). From the adsorption isotherms, the maximum adsorption capacity of the gel for both Cu(II) and Pb(II) was found to be 0.47 mol/kg whereas that for Cd(II) was 0.24 mol/kg. A continuous flow experiment for Cd(II) showed that the gel can be useful for pre‐concentration and complete removal of Cd(II) from aqueous solution.