水化针刺GCL+GM复合衬里的单剪破坏特征

针刺GCL和HDPE土工膜(GM)广泛应用于填埋场防渗衬里,GCL的内部剪切强度和GCL/GM界面剪切强度是填埋场复合衬里边坡滑移稳定性的控制因素。通过开展不限定剪切破坏面的水化针刺GCL+GM复合衬里大单剪试验,获得了剪切过程中GCL/GM界面位移和GCL内部位移发展规律,分析了GM的糙面分别与GCL的有纺面和无纺面接触时的峰值强度,揭示了GCL+GM复合衬里的整体剪切破坏特征。试验结果表明:大单剪试验能够正确和合理地模拟GCL与GM间的相互作用,GCL+GM复合衬里中的极限破坏面不仅会随着法向应力的增加而发生转移,甚至出现GCL内部和GCL/GM界面同时成为剪切破坏面的临界状态。     

Shear strength of geosynthetic composite systems for design of landfill liner and cover slopes

Torsional ring shear tests were performed on composite specimens that simulate the field alignment of municipal solid waste (MSW) landfill liner and cover system components. Simultaneous shearing was provided to each test specimen without forcing failure to occur through a pre-determined plane. Composite liner specimens consisted of a textured geomembrane (GM) underlain by a needle-punched geosynthetic clay liner (GCL) which in turn underlain by a compacted silty clay. Hydrated specimens were sheared at eleven different normal stress levels. Test results revealed that shear strength of the composite liner system can be controlled by different failure modes depending on the magnitude of normal stress and the comparative values of the GCL interface and internal shear strength. Failure following these modes may result in a bilinear or trilinear peak strength envelope and a corresponding stepped residual strength envelope. Composite cover specimens that comprised textured GM placed on unreinforced smooth GM-backed GCL resting on compacted sand were sheared at five different GCL hydration conditions and a normal stress that is usually imposed on MSW landfill cover geosynthetic components. Test results showed that increasing the GCL hydration moves the shearing plane from the GCL smooth GM backing/sand interface to that of the textured GM/hydrated bentonite. Effects of these interactive shear strength behaviors of composite liner and cover system components on the possibility of developing progressive failure in landfill slopes were discussed. Recommendations for designing landfill geosynthetic-lined slopes were subsequently given. Three-dimensional stability analysis of well-documented case history of failed composite system slope was presented to support the introduced results and recommendations.     

水化针刺GCL剪切破坏机理的试验研究

土工膨润土防水毯(GCL)的内部剪切强度是影响复合防渗衬里边坡稳定性的关键因素,加筋纤维的存在使针刺GCL的内部剪切强度明显高于非加筋GCL。含水化GCL的复合防渗衬里结构剪切试验会发生应力小峰值现象,但大都被研究人员忽视;加筋纤维对GCL峰值剪切强度的贡献处于定性阶段。通过开展GCL内夹钠基膨润土的饱和剪切试验和理论分析,证实应力小峰值现象为水化针刺GCL应力位移曲线的固有特征,并且小峰值应力代表了GCL内夹膨润土的抗剪强度贡献。以应力位移曲线上的应力小峰值现象为基础,将加筋纤维对GCL峰值剪切强度的贡献定量化,结合破坏机理分析了针刺GCL内部剪切破坏和应力位移发展过程。考虑针刺GCL剪切强度各部分贡献,提出了一种能反映针刺GCL破坏机理的峰值强度准则。     

Failure mechanisms of geosynthetic clay liner and textured geomembrane composite systems

The objective of this study was to evaluate shear behavior and failure mechanisms of composite systems comprised of a geosynthetic clay liner (GCL) and textured geomembrane (GMX). Internal and interface direct shear tests were performed at normal stresses ranging from 100 kPa to 2000 kPa on eight different GCL/GMX composite systems. These composite systems were selected to assess the effects of (i) GCL peel strength, (ii) geotextile type, (iii) geotextile mass per area, and (iv) GMX spike density. Three failure modes were observed for the composite systems: complete interface failure, partial interface/internal failure, and complete internal failure. Increasing normal stress transitioned the failure mode from complete interface to partial interface/internal to complete internal failure. The peak critical shear strength of GCL/GMX composite systems increased with an increase in GMX spike density. However, the effect of geotextile type and mass per area more profoundly influenced peak critical shear strength at normal stress > 500 kPa, whereby an increase in geotextile mass per area enhanced interlocking between a non-woven geotextile and GMX. Peel strength of a GCL only influenced the GCL/GMX critical shear strength when the failure mode was complete internal failure.     

Stress-controlled direct shear testing of geosynthetic clay liners I: Apparatus development

The use of geosynthetic clay liners (GCLs) in waste containment applications can induce long-term normal and shear stresses as well as expose GCLs to elevated temperatures and non-standard hydration solutions. Considering the importance of GCL internal shear strength to the design and integrity of waste containment barrier systems, innovative laboratory testing methods are needed to assess shear behavior of GCLs. There were two main objectives of this study: (i) develop a stress-controlled direct shear apparatus capable of testing GCLs exposed to elevated temperatures and hydrated in non-standard solutions; and (ii) assess internal shear behavior of GCLs under varying experimental conditions (e.g., stress, temperature, solution). These two objectives were partitioned into a two-paper set, whereby Part I (this paper) focuses on the shear box design and Part II focuses on an assessment of shear behavior. The direct shear apparatus includes a reaction frame to mitigate specimen rotation that develops from an internal moment within needle-punched reinforced GCLs. Rapid-loading shear tests were conducted to assess functionality of the apparatus and document baseline shear behavior for a heat-treated and a non-heat treated needle-punched GCL with comparable peel strength. These two GCLs failed at comparable applied shear stress; however, the heat-treated GCL yielded lower shear deformation and failure occurred via rupture of reinforcement fiber anchors, whereas the non-heat treated GCL yielded larger shear deformation and failure via pullout of reinforcement fibers.     

水化状态对含针刺GCL复合衬里抗剪强度的影响分析

针刺GCL和HDPE土工膜(GM)在防渗工程中应用广泛,含多层界面的复合衬里整体抗剪强度是边坡稳定性分析的关键。介绍了含针刺GCL复合衬里的大单剪试验方法,并且对比分析了针刺GCL初始状态分别为干燥和完全水化两种情况下的复合衬里抗剪强度。结果表明,复合衬里的剪切破坏不会发生在干燥针刺GCL内部界面,而GCL干燥状态下的复合衬里单剪强度未必高于GCL完全水化状态下的复合衬里单剪强度。结合含GCL复合衬里的剪切破坏机理,阐述了针刺GCL的水化状态对复合衬里抗剪强度的影响。含GCL复合衬里在不同水化状态下的界面滑移稳定性都应引起工程人员的重视。     

Cyclic shear behavior of GMB/GCL composite liner

The composite liner system consisting of geomembrane (GMB) and geosynthetic clay liner (GCL) has been widely used in landfills. Although there have been a lot of studies on the monotonic shear behavior of GMB/GCL composite liner, the dynamic test data are still very limited and consequently, the dynamic shear mechanism is not clear. A series of displacement-controlled cyclic shear tests were conducted to study the shear behavior of GMB/GCL composite liner, including the shear stress versus horizontal displacement relationships, backbone curves, and shear strengths. Hysteretic loops in the shape of parallelogram were obtained and equivalent linear analyses revealed that the secant shear stiffness decreased and the damping ratio increased with the rise in loading cycles. According to the test results, it is generally acceptable to predict the dynamic peak strength of a GMB/GCL composite liner with its static strength envelope. Furthermore, the dynamic softening mechanism and rate-dependent shear stiffnesses were well described by the proposed equations, which also facilitate the accurate modeling of the cyclic shear behavior.     

Stress-controlled direct shear testing of geosynthetic clay liners II: Assessment of shear behavior

This paper is the second of a two-paper set on stress-controlled direct shear testing of geosynthetic clay liners (GCLs). Design of the apparatus, preliminary experiments, and shear deformation mechanisms in heat-treated and non-heat treated needle-punched (NP) GCLs were discussed in Part I. The objective of Part II (this paper) was to evaluate the effects of physical factors (i.e., peel strength and initial normal stress, σ_ni), environmental factors (i.e., temperature and hydration solution), and creep on the internal shear behavior of NP GCLs. In addition, failure conditions of GCLs in the stress-controlled direct shear tests were compared to displacement-controlled direct shear tests to verify results. An increase in internal shear strength developed from increased GCL peel strength or increased normal stress. Elevated temperatures were observed to decrease internal shear strength for both non-heat treated and heat-treated NP GCLs. Specimens hydrated with a calcium-rich synthetic mining solution experienced increased internal shear strength due to cation exchange in the bentonite, whereas specimens hydrated with a highly alkaline synthetic mining solution experienced decreased internal shear strength. Creep tests revealed an increase in time-to-failure with decrease in applied shear stress. Finally, stress states at failure from stress-controlled and displacement-controlled shear tests corresponded to a unique failure envelope, which validates the efficacy of using stress-controlled direct shear tests to assess internal shear behavior and shear strength of NP GCLs.     

Factors affecting the down-slope erosion of bentonite in a GCL

Leaving a composite liner exposed for an extended period can sometimes lead to down-slope bentonite erosion from geosynthetic clay liners (GCLs). This laboratory study examines a number of factors that can affect the erosion of bentonite particles with an imposed flow of water for one particular geotextile-encased, needle-punched GCL. The factors examined include the effect of an initial wet/dry cycle, water chemistry, flow rate, slope, prior cation exchange, and the effect of no-drying phase in the test cycle. No erosion was observed unless the GCL had been hydrated and dried to create a wet/dry cycle. The most critical factor was found to be the water chemistry. No erosion was observed with tap water (39 ppm calcium) with up to 360 cycles and a flow of 3 L/hour. Tests simulating the evaporation and condensation of water below an exposed composite liner by imposing deionized water on the GCL surface developed erosion holes within 5–6 cycles.     

Evaluation of Interface Shear Strength between Geosynthetics Under Wet Condition

This paper presents direct shear testing data for interfaces between a nonwoven geotextile or two types of geosynthetic clay liners (GCL) (reinforced and unreinforced) and two types of geomembranes (smooth and textured). In this study, the effect of moisture on interface shear behavior was investigated by performing shear tests in both dry and wet (or hydrated) conditions because the geosynthetic interfaces in a landfill are easily exposed to rain, leachate and groundwater beneath the liners. The degree of strength reduction with increasing displacement and the effect of the normal stress level on friction angles were examined, and the modified hydration method applied for the GCL was also validated. The test results showed that the normal stress level, interface water presence and hydration methods dominated the interface shear strength and behavior. The relationship between the peak secant friction angle and the normal stress demonstrated that the friction angle decreased with increasing normal stress, implying that the shear strength for safe design should be determined by using the maximum value of the normal stress applied in landfills. Finally, comparisons with a few published test results were presented and some design implications for the geosynthetic-installed landfills were discussed.     

Evaluation of interface shear strength of composite liner system and stability analysis for a landfill lining system in Thailand

The paper presents the case history of laboratory evaluation of the interface shear strength properties of various interfaces encountered in a modern day landfill with emphasis on proper simulation of field conditions and subsequent use of these results in the stability analyses of liner system. Over 70 large direct shear tests were systematically conducted to evaluate the interface shear strength properties of composite liner system using project specific materials under site specific conditions, being used at non-hazardous and hazardous landfills project situated in Sa Kaeo Province, Thailand. The critical interfaces were located between the geotextiles and the smooth geomembrane (GM), the smooth GM and the geosynthetic clay liner (GCL), and the smooth GM liner and the compacted clay liner (CCL) with the interface friction angles ranging from 6.5° to 10.5° for dry conditions and 6.5° to 9.5° in wet conditions. The residual shear stress for these interfaces was attained at a displacement less than 4 mm. Three methods, namely, limit equilibrium method (LEM), limit method (LM), and the simple composite column (SCC) approach were used to evaluate the tensile loads induced in the geosynthetic components. The SCC approach proposed by Liu, C.N. [2001. Tension of geosynthetics material regarding soils on landfill liner slopes. Proceedings, National Science Council ROC(A), 25(4), 211–218] that takes into account the force equilibrium as well as displacement compatibility yielded satisfactory results. The factor of safety for geosynthetic components in the liner was found to be greater than 3.0 for both types of landfill.     

Investigation of mechanisms of bentonite extrusion from GCL and related effects on the shear strength of GCL/GM interfaces

Two groups of laboratory tests were carried out to investigate the effect of bentonite extrusion from a hydrated GCL on the shear strength of GCL/GM interfaces. All tests were performed with the woven geotextile side of GCL against the GM. The first group of tests were one-dimensional loading tests in which the GCL/GM specimens were subjected to hydration and vertical loading involving different sequences and loading rates. The second group of tests were large direct shear tests that studied the effect of shearing on bentonite extrusion and hence on shear strength reduction. It was found that bentonite extrusion occurs more readily from GCL/GM interfaces subjected to a swelling-loading sequence than those subjected to a loading-swelling sequence. The quantity of extruded bentonite during the normal loading showed an increasing trend with an increase in loading rate. The total mass/area of extruded bentonite during the normal loading ranged from 0 to 21.9 g/m², which was less than the quantity of bentonite extruded during the subsequent shearing (i.e., 10.7 – 81.1 g/m²). It was found that the volume of bentonite extruded at the large shear displacement caused a significant strength loss equivalent with 8° in terms of interface friction angle. The influence of bentonite extrusion on the peak shear strength showed a magnitude of 3.5° in terms of interface friction angle. The relatively insignificant bentonite extrusion during hydration and normal loading was observed to have a minor effect on the strength loss. Observations from the experimental results provide further insight into the mechanisms of bentonite extrusion.     

Hysteresis of the water retention curves of geosynthetic clay liners in the high suction range

This paper examines two needle-punched geosynthetic clay liners' water retention behaviour at high suction ranges using the vapour equilibrium technique where super-saturated salt solutions controlled the relative humidity. This study shows that the bentonite form and its mineralogy affect the absorption/desorption of GCLs and their corresponding water retention curves. In particular, a granular bentonite-based GCL was found to absorb more and release less water than a powdered bentonite-based GCL due to its higher montmorillonite content and larger pores. The water retention curves of both GCLs exhibited very little hysteretic behaviour at high suction. Repeated wetting-drying cycles shifted the WRCs of both GCLs slightly downward with minimal impact on their degree of hysteresis.     

Geomembrane strains from coarse gravel and wrinkles in a GM/GCL composite liner

The physical response of a 1.5-mm-thick, high-density polyethylene geomembrane (GM) is reported when placed on top of a needle-punched geosynthetic clay liner (GCL), buried beneath 50-mm coarse gravel and subjected to vertical pressure in laboratory experiments. Local strains in the geomembrane caused by indentations from the overlying gravel and deflections of a wrinkle in the geomembrane are quantified. A peak strain of 20% was calculated when a flat geomembrane was tested without a protection layer at an applied vertical pressure of 250 kPa. Strains were smaller with a nonwoven needle-punched geotextile protection layer between the gravel and geomembrane. Increasing the mass per unit area of the geotextile up to 2200 g/m² reduced the geomembrane strain. However, none of the geotextiles tested were sufficient to reduce the geomembrane strain below an allowable limit of 3%, for the particular 50-mm gravel tested and when subjected to a vertical pressure of 250 kPa. Increasing the initial GCL water content and reducing the stiffness of the foundation layer beneath the GCL were found to increase the geomembrane strains. These local strains were greater when a wrinkle was present in the geomembrane. The wrinkle in the geomembrane experienced a decrease in height and width. The wrinkle deformations lead to larger pressures beside the wrinkle and hence producing larger local strains. A 150-mm-thick sand protection layer was effective in limiting the peak strain to less than 0.3% even with a wrinkle in the geomembrane, at a vertical pressure of 250 kPa.     

Instrumentation for monitoring field performance of the Cincinnati GCL test plots

Fourteen full-scale cover systems were constructed at a site in Cincinnati, Ohio, to understand better the strength capability of various GCLs as a component in cover systems. Four different geosynthetic clay liner (GCL) products were installed in full-scale cover systems on two different slopes. The main objective of the project was to monitor the internal shear strength of the GCLs over time. This required in-situ yet economic instrumentation. Instruments were designed, calibrated and installed in the test plots in order to monitor the moisture content of the subsoil and moisture content within the bentonite component of the GCL. In addition, total and differential deformations of the GCLs were monitored. The focus of'this paper is to report the details of instrumenting the GCLs rather than to report on specific GCL performance.     

Interface shear strength between geosynthetic clay liner and covering soil on the embankment of an irrigation pond and stability evaluation of its widened sections

Geosynthetic clay liners (GCLs) are typically used for widening sections of an embankment. They are also used as low permeability liners to minimize water leakage from reservoirs such as irrigation ponds. However, few investigations have been carried out on the specific properties of GCLs, such as granulated bentonite sandwiched between geotextiles, their internal shear strength, and the shear strength at the interface between a GCL and an embankment body. In this study, a series of direct box shear tests were performed to determine the shear strength properties of bentonite and compacted soils as well as at the interface between a GCL and bentonite or compacted soil. In addition, a series of field-loading tests were conducted to investigate the failure behaviour of an embankment body containing a GCL when changes in the water content of the bentonite of the GCL in a real embankment occur. Furthermore, the stability of widened embankment bodies that incorporated GCLs were evaluated. The main conclusions of this study are as follows: (1) The shear strength of the interface between the covering soil and geotextiles varied according to the soil type, geotextile type, and the submergence period, (2) the maximum safety factor was observed at the interface between decomposed granite soil and the geotextiles, while the minimum safety factor was observed at the interface between the bentonite and the geotextiles, and (3) the influence of GCLs on the instability of a widened embankment was extremely small.     

Shear strength behavior of clayey soil reinforced with polypropylene fibers under drained and undrained conditions

The fundamental mechanisms controlling shear strength and deformability behavior of clay-fiber mixtures have still not been well established, nor the constraints that may affect their performance of shearing under different drainage conditions. This study aims to understand the behavior of a clay soil mixed with polypropylene fibers using results from drained and undrained triaxial compression tests, and to provide necessary calibration data for a shear strength prediction model. In drained tests, shear strength increased with fiber inclusion for a given mean effective stress, represented by an increase in apparent cohesion. In the undrained tests, the shear strength was not affected by pore water pressure generation. Results from the drained and undrained tests indicate that the fiber content had a greater influence on the apparent cohesion than on the friction angle. Drainage affected the improvement in the peak shear strength of fiber-reinforced soils, with superior improvement in the drained tests. As the percent improvement in shear strength decreased with increasing effective confining stresses for both tests, the difference in behavior in the drained and undrained tests was attributed to the strain at failure, with failure occurring at large strains in the drained tests but at smaller strains in the undrained tests.     

赤泥渗滤液对改性GCL防渗性能的影响

旨在评价商用土工合成材料黏土衬垫(GCL)用于阻隔赤泥渗滤液的有效性。赤泥渗滤液作用下GCL的防渗特性是评价其防污性能的关键因素。以商用改性GCL中膨润土为研究对象,通过自由膨胀试验,研究了4种赤泥渗滤液中膨润土的自由膨胀指数。以商用改性GCL为研究对象,通过改进滤失试验,研究了4种赤泥渗滤液作为渗透液作用下GCL渗透系数的变化规律,评价了预水化作用对渗透系数的影响。研究还采用清洁自来水作为GCL的渗透液作为对照。结果表明,随着离子强度的增加,改性GCL中的膨润土自由膨胀指数随之减小。预水化处理改性GCL的渗透系数相较于未预水化处理试样降低了5倍左右。在实际工程应用中,建议采用自来水预水化处理GCL,以此充分发挥其防渗性能。随着改进滤失试验中施加气压的增大,不同赤泥渗滤液作用下的改性GCL渗透系数均下降。随着离子强度和一价二价离子摩尔数比的增加,改性GCL的渗透系数随之增大。随着膨润土自由膨胀指数的增加,改性GCL的渗透系数随之减小。与自来水渗透情况相比,赤泥渗滤液渗透作用下,改性GCL渗透系数增大4.35~12.0倍。     

Geosynthetic clay liners: Perceptions and misconceptions

The behaviour of geosynthetic clay liners (GCLs) as part of a physical-environmental system is examined. Consideration is given to: (a) both the physical and hydraulic interactions with the materials, and the chemical interactions with the fluids, above and below the liner, (b) time-dependent changes in the materials, (c) heat generated from the material to be contained, as well as (d) the climatic conditions both during construction and during service. This paper explores some common perceptions about GCL behaviour and then examines the misconceptions that can arise and their implications. It demonstrates how what may first appear obvious is not always as one expects and that more is not always better. It discusses: (i) the pore structure of a GCL, (ii) the dependency of the water retention curve of the GCL on its structure, bentonite particle sizes and applied stress, (iii) the effect of the subgrade pore water chemistry, (iv) the mineralogy of the subgrade, and (v) thermal effects. The desirability of a GCL being reasonably well-hydrated before being permeated is examined. The critical size of needle-punch bundles at which preferential flow can increase hydraulic conductivity by orders of magnitude is illustrated. The dependency of self-healing of holes on the interaction between GCL and subgrade is discussed. Finally, the transmissivity of the geomembrane/GCL interface is shown to be a function of GCL and geomembrane characteristics and to be poorly correlated with GCL hydraulic conductivity.     

氨氮在土工合成黏土衬垫中的扩散行为研究

氨氮是垃圾渗滤液中最具代表性的污染物之一,但其在土工合成黏土衬垫(GCL)中的扩散行为至今尚未得到重视。开展批式吸附试验和扩散试样浸提试验测定氨氮在GCL中的吸附分配系数;进行扩散试验测定氨氮在GCL中的扩散系数;基于试验得到的吸附分配系数和扩散系数,使用数值软件POLLUTE v7.0对氨氮在GCL中的运移行为进行模拟。试验结果表明,氨氮在膨润土上的吸附分配系数为0.017L/g,在GCL中的扩散系数约为9.0×10^-11m²/s。POLLUTE v7.0的模拟结果显示,当考虑扩散存在时,氨氮将提前30 a击穿GCL。