酸刻蚀处理对IrO2-Ta2O5/Ti阳极寿命的影响

通过改变腐蚀方法,研究了使用H₂C₂O₄和H₂SO₄进行钛基体表面刻蚀对金属氧化物钛阳极电化学性能和表面形貌的影响。采用扫描电子显微镜、X射线衍射仪和光电子能谱等测试方法对样品进行了结构分析。然后利用电化学工作站测试了样品的电催化活性,利用加速寿命测试研究了样品的电化学稳定性。结果表明,通过H₂C₂O₄和H₂SO₄分步腐蚀可以获得更加均匀致密的表面形貌和更好的催化稳定性。在此基础上,进一步研究了预处理对钛阳极寿命的影响原因。IrO₂-Ta₂O₅/Ti阳极的催化活性和稳定性与酸刻蚀处理的先后顺序及表面结构密切相关,并建立了预处理方法与阳极性能之间的关系。分步腐蚀使钛表面具有合适的粗糙度,因而提升了涂层附着力。在热分解过程中,经分步腐蚀形成的氢化钛在不改变表面形貌的情况下转变为金红石结构的氧化钛,有利于电子输运,从而增强涂层附着力并延长加速寿命。     

Ar/N2-Ar共溅射Ti掺杂对Ta2O5 涂层光学和力学性能的影响

为了探索Ar/N₂-Ar共溅射Ti掺杂对Ta₂O₅涂层光学性能和力学性能的影响,采用射频和直流磁控共溅射技术在玻璃基底表面制备了Ta₂O₅、N₂-Ta₂O₅、Ti-Ta₂O₅和N₂-Ti-Ta₂O₅涂层。利用X射线衍射仪（XRD）、扫描电子显微镜（SEM）、原子力显微镜（AFM）表征了Ta₂O₅、N₂-Ta₂O₅、Ti-Ta₂O₅和N₂-Ti-Ta₂O₅涂层的微观结构和表面形貌;通过紫外可见分光光度计测试了涂层的光学参数;采用纳米压痕仪测试了涂层的硬度和杨氏模量。XRD测试结果表明,Ta₂O₅、N₂-Ta₂O₅、Ti-Ta₂O₅和N₂-Ti-Ta₂O₅涂层主要以Ta₂O₅为主体的非晶相结构组成。SEM和AFM结果显示,沉积在玻璃基底上的涂层未出现大面积空隙,溅射粒子在基底表面均匀堆积生长,并且涂层沉积厚度基本一致,厚度误差在5%以内。分别引入N₂和Ti及N₂-Ti共掺杂,均可降低Ta₂O₅涂层的粗糙度。光学测试结果表明,分别引入N₂和Ti元素,可以提高Ta₂O₅涂层的平均透射率至81%以上,而N₂-Ti共掺杂制备的N₂-Ti-Ta₂O₅涂层平均透射率降低。力学测试结果显示,与Ta₂O₅涂层对比,N₂-Ta₂O₅和N₂-Ti-Ta₂O₅涂层的硬度显著增大,Ti-Ta₂O₅涂层硬度基本一致。弹性指数（H/E）和塑性指数（H³/E²）表明,N₂-Ta₂O₅涂层和N₂-Ti-Ta₂O₅涂层具备更好的断裂韧性和抗塑性变形能力。在玻璃表面制备Ta₂O₅掺杂N₂和Ti元素的涂层,可以实现以N₂-Ta₂O₅涂层和N₂-Ti-Ta₂O₅涂层为代表的、同时具备优异光学性能和力学性能的多功能涂层。     

SnO2 增强相对AgCuOIn2O3 电触头材料显微组织与性能的影响

采用反应合成法结合塑性变形工艺制备了不同SnO₂含量的AgCuOIn₂O₃SnO₂电触头材料,利用扫描电镜和金相显微镜表征了材料的微观形貌及显微组织,分析对比了不同SnO₂含量的材料金相组织及其增强相的分布均匀性,并利用X射线衍射分析了材料的物相结构。测量了材料的抗拉伸强度、硬度、电阻等性能。结果表明：添加适量的SnO₂能使组织中的孔隙尺寸缩小、其他缺陷明显减少。氧化物弥散分布在银基体中,极大地改善了AgCuOIn₂O₃电触头材料的显微组织均匀性。在SnO₂含量不变时,材料的电阻率随塑性变形程度增加而有所降低;随着SnO₂含量增多,电阻率呈现先降低后升高的趋势,最后趋于定值,约为2.4 μΩ·cm。添加SnO₂后各试样材料的硬度均显著升高,SnO₂含量为1%（质量分数）的材料具有最优的抗拉伸强度和延伸率。     

Fe2O3-CaO-TiO2 体系下铁酸钙的合成过程及TiO2 和CaTiO3 的影响

为了确定高钛型钒钛磁铁矿烧结过程中铁酸钙的生成是受TiO₂还是TiO₂和CaO形成的CaTiO₃影响,首先利用Fe₂O₃和CaO的纯试剂合成了铁酸钙,并研究了TiO₂和CaTiO₃对钛铁酸钙 （FCT） 形成的影响。在Factsage 7.0软件进行热力学计算的基础上,通过在空气气氛下进行烧结,获得了在1023~1423 K温度范围内、不同烧结时间的不同样品。通过X射线衍射和扫描电镜-能谱分析等表征手段,对烧结样品的物相转变和微观结构变化进行了表征。发现FCT的形成过程主要分为2个阶段：前一阶段为1023~1223 K温度范围内Fe₂O₃与CaO之间的反应,合成产物为Ca₂Fe₂O₅,反应方程式为“Fe₂O₃(s)+ 2CaO(s)= Ca₂Fe₂O₅(s)”;后一阶段为1223~1423 K温度范围内Ca₂Fe₂O₅和Fe₂O₃的反应,主要产物为CaFe₂O₄,反应为“Ca₂Fe₂O₅(s)+ Fe₂O₃(s)= 2CaFe₂O₄(s)”,该阶段尤其是温度为1423 K时,反应速率显著加快,随温度的升高CaTiO₃显著增加。然而,Ti元素在铁酸钙中的固溶很难实现,TiO₂与铁酸钙之间的反应不是形成FCT的有效途径。随着保温时间的延长,CaTiO₃和FCT相界中Fe元素含量增加。FCT主要是通过Fe组分在CaTiO₃中固溶形成的,主要反应是“Fe₂O₃+CaTiO₃(s)=FCT(s)”。     

CaO-Bi2O3-MoO3-xNb2O5复合掺杂对高磁导率Mn-Zn铁氧体的微观结构和电磁性能的影响

采用高温固相反应制备了CaO-Bi_2O_3-MoO_3-XNb_2O_5(X=0.000%~0.075%,质量分数,步长:0.015%)复合掺杂的高磁导率Mn-Zn铁氧体材料,利用XRD、SEM、四探针电阻测试仪、阻抗分析仪、和软磁测试仪等分析测试手段对材料结构和性能进行表征,研究了复合掺杂剂中Nb_2O_5掺杂量对高磁导率Mn-Zn铁氧体材料的结构和电磁性能的影响。结果表明:当Nb_2O_5少量掺杂时,Nb_2O_5可以改善材料的微观结构,提高其密度、频率稳定性和品质因数,提高其电阻率,降低其体积功耗;当Nb_2O_5过量掺杂时,Nb_2O_5将恶化材料的微观结构,导致材料的电磁性能变差。当Nb2O5掺杂量为0.030%时材料的综合电磁性能最佳。     

原子层沉积Al2O3 保护层氢终端金刚石MISFETs的电学特性

研究了Zr-Si-N氢终端金刚石（H-diamond）绝缘栅场效应晶体管（MISFET）在有无Al₂O₃保护层情况下的电学特性。分别采用原子层沉积法（ALD）和射频溅射法（RF）制备了Al₂O₃保护层和Zr-Si-N栅介质层。MISFETs的转移特性曲线表明,其栅阈值电压在有无Al₂O₃保护的情况下从-2.5 V变化到3 V,表明器件从常关型转换为常开型。输出和转移特性曲线揭示了氧化铝的存在保护了氢终端,使其免受磁控溅射过程的损伤。     

La2O3掺杂氧化铝气凝胶的制备与耐温性能研究

以仲丁醇铝为前驱体,采用溶胶-凝胶法结合丙酮-苯胺原位生成水技术,通过乙醇超临界干燥,制备出不同含量(1.5 mol%~12 mol%)La₂O₃掺杂的氧化铝气凝胶。采用电子扫描电镜(SEM)、透射电子显微镜(TEM)、X线衍射仪(XRD)、N₂吸附分析仪等仪器表征了La₂O₃掺杂对氧化铝气凝胶的微结构和耐温性能的影响。结果表明：La₂O₃的引入使氧化铝气凝胶的形貌由球状颗粒向大的片状结构转变。适量的La₂O₃掺杂能提高氧化铝气凝胶的比表面积,9 mol% La₂O₃掺杂的氧化铝气凝胶比表面积最大。通过La₂O₃掺杂,能够抑制氧化铝晶粒在高温下的生长和α-Al₂O₃的相变,提高氧化铝气凝胶的耐温性能。1200℃热处理后,La₂O₃掺杂的氧化铝气凝胶仍维持在θ-Al₂O₃,比表面积为86.5 m₂/g,高于未掺杂的氧化铝气凝胶(46 m₂/g)。     

La2O3掺杂AgSnO2电接触材料的制备及性能研究

以Ag、Sn、La₂O₃粉为原料,采用机械合金法制备复合粉体。结合氧化法与粉末冶金工艺,对复合粉体进行氧化、压制、烧结。采用扫描电镜(SEM)和能谱仪、硬度计、金相显微镜、金属电导率测量仪等对复合粉体氧化前后的形貌以及电接触材料烧结前后的性能进行表征。结果表明：烧结后,电接触材料硬度较于烧结前明显下降。同时电接触材料随Sn含量增大,电阻率升高,密度反而下降。在一定的La₂O₃(0wt.%、0.75wt.%、1.5wt.%、2.25wt.%、3wt.%)含量范围内,La₂O₃掺杂量越高,密度越低。同时电接触材料经烧结后,随La₂O₃含量增加,其电阻率先降后升,在La₂O₃含量为0.75wt.%时,电接触材料的电阻率最低。     

BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

Al2O3/Ti2AlN复合材料在900℃,1000℃和1100℃空气中的氧化行为

利用综合热分析仪、背散射扫描电镜(BSE)和能谱分析(EDS)对Al₂O₃/Ti₂AlN复合材料在900 ℃,1 000 ℃和1 100 ℃/20 h空气中连续氧化20h后的氧化增重及氧化层截面进行了研究。结果表明：Al₂O₃/Ti₂AlN复合材料在空气中的氧化行为符合抛物线规律,在900 ℃,1 000 ℃和1 100 ℃/20 h氧化增重分别为2.78×10_-2 kg/m₂、10.4 ×10_-2 kg/m₂、21.9 ×10_-2 kg/m₂,抛物线速率常数相应为1.08×10_-8 kg₂/m₄s、1.44×10_-7 kg₂/m₄s、6.56×10_-7 kg₂/m₄s,氧化激活能为274 kJ/mol。氧化层主要由TiO₂和Al₂O₃组成的,连续的Al₂O₃次外层可以提高其抗氧化性能。氧化层结构的改变是由于氧化温度对Ti₄₊、Al₃₊由基体表面向外扩散和O_2-向内扩散的影响,以及TiO₂和Al₂O₃在不同温度下的形核生长速率导致的。对Al₂O₃/Ti₂AlN而言,控制材料与氧化气氛的界面是提高该材料抗氧化性能的关键。     

Degradation mechanism of long service life Ti/IrO2-Ta2O5 oxide anodes in sulphuric acid

Ageing performances of long service life Ti/70%IrO₂-30%Ta₂O₅ (at mole fraction) anodes prepared at 450 °C over the whole electrolysis time in H₂SO₄ solution have been investigated. It is showed that, the whole electrolysis processes of these anodes can be divided into three stages consisting of `active', `stable' and `de-active' regions. In the first two stages, the dissolution of coated oxides is dominated (with IrO<sub>2</sub> component preferential loss) which results in decreasing of apparent current for oxygen evolution and voltammetric charge. It is found that, in these two stages, the preferential orientations of (1 1 0) and (1 0 1) planes in IrO<sub>2</sub> rutile decreases with electrolysis time, and that of (0 0 2) plane increases, while the preferential orientations remain to be stabilized in the `de-active' region. Therefore, the loss mechanism of catalyst coatings in this region is changed. Electrochemical impedance spectroscopy measurement shows a slight increase in reaction resistance (R_ct) of oxide catalysts for oxygen evolution in the `de-active' region, while a sharp rise in totally physical impedance of the whole anode. According to the experimental results, a degradation mechanism of the Ti based anodes has been proposed by degradation of Ti/catalyst layer interface resulting from the dissolution and anodic oxidation of metal base alternatively.     

成分配比对Ti/IrO2-Ta2O5电极电容性能影响

摘要：采用低温热分解法制备了Ti基IrO2-Ta2O5氧化物涂层电极。通过X射线衍射(XRD),循环伏安曲线,交流阻抗谱,恒流充放电等测试方法分析了Ta含量对IrO2-Ta2O5氧化物涂层组织结构及电容性能的影响。结果表明,Ta2O5可抑制IrO2的晶化程度。随涂层中Ta含量增加,晶化度降低。当Ta含量为60mol%时,IrO2-Ta2O5电极的结晶度为6.4%,具有较小的电荷转移电阻和最高的比电容（239.2F/g）,比IrO2电极比电容(54.1F/g)提高了近4倍。     

Ti/IrO2+MnO2电极在酸性溶液中的析氧反应动力学研究

采用涂覆热分解法制备Ti/IrO₂+MnO₂复合电极,利用慢速线性电位扫描伏安法测试Ti/IrO₂+MnO₂电极的准稳态极化曲线并深入地研究析氧反应动力学,得到了相关动力学参数、反应历程及速度控制步骤。通过分析经欧姆电压降修正的Tafel曲线,较好地解释了Tafel直线区域的双斜率现象,基于此提出析氧反应动力学方程并进行数学推导,较好地符合实验结果。实验所得氢离子反应级数约为零,低电位区与高电位区的表观活化能分别为30.31和13.64 kJ/mol,进一步证明该数学模型的正确性。     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.     

国外多孔基体氧化铝/氧化铝复合材料工程应用进展

氧化铝/氧化铝复合材料(Al2O3/Al2O3)是20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,已经发展为与SiC/SiC、C/SiC等非氧化物陶瓷基复合材料并列的一类陶瓷基复合材料。与非氧化物陶瓷基复合材料相比,Al2O3/Al2O3具有长时抗氧化、高温耐腐蚀、低成本等独特优势,已经在航空发动机、地面燃气轮机等军民两用热结构材料领域展现出广阔的应用前景。本文从材料应用的角度出发,系统分析阐述了目前在Al2O3/Al2O3占主导地位的多孔基体Al2O3/Al2O3(P-Al2O3/Al2O3)的增韧机制、成型工艺和性能特点,重点归纳了国外近年来P-Al2O3/Al2O3的工程化应用进展及前景,最后指出了P-Al2O3/Al2O3存在的局限性并展望了未来发展方向,旨在为国内Al2O3/Al2O3体系发展提供借鉴和参考。     

Thermite reduction of Ta2O5/SiO2 powder mixtures for combustion synthesis of Ta-based silicides

Tantalum silicides (including TaSi₂, Ta₅Si₃, Ta₂Si, and Ta₃Si) were prepared by solid state combustion of the Ta-Si reaction system involving thermite reduction of Ta₂O₅ and SiO₂. The thermite-based combustion is self-sustaining and contributes to the in situ formation of tantalum silicides along with Al₂O₃. The combustion front temperature and propagation velocity increased with the extent of thermite reactions for the systems adopting the thermite mixture of Al-Ta₂O₅, while both of them decreased for those using Al, Ta₂O₅, and SiO₂ as the thermite reagents. Among four silicide compounds, a better degree of phase evolution was observed for TaSi₂ and Ta₅Si₃ when compared to that of Ta₂Si and Ta₃Si. The XRD analysis indicated the presence of a small amount of Ta₅Si₃ in the TaSi₂-Al₂O₃ composite. On the formation of Ta₅Si₃ with Al₂O₃, the minor phase was Ta₂Si for the Al-Ta₂O₅-containing system. In addition to Ta₂Si, an intermediate phase TaSi₂ was detected when the Al-Ta₂O₅-SiO₂ mixture was used. However, combustion yielded comparable amounts of Ta₂Si and Ta₅Si₃ in the synthesis of the Ta₂Si-Al₂O₃ composite. Moreover, instead of forming Ta₃Si the reaction produced Ta₂Si as the dominant phase along with unreacted Ta.     

Effects of K2O-Li2O doping on surface and catalytic properties of Fe2O3/Cr2O3 system

The effects of K₂O and Li₂O-doping (0.5, 0.75 and 1.5 mol%) of Fe₂O₃/Cr₂O₃ system on its surface and the catalytic properties were investigated. Pure and differently doped solids were calcined in air at 400-600 °C. The formula of the un-doped calcined solid was 0.85Fe₂O₃:0.15Cr₂O₃. The techniques employed were TGA, DTA, XRD, N₂ adsorption at −196 °C and catalytic oxidation of CO oxidation by O₂ at 200-300 °C. The results revealed that DTA curves of pure mixed solids consisted of one endothermic peak and two exothermic peaks. Pure and doped mixed solids calcined at 400 °C are amorphous in nature and turned to α-Fe₂O₃ upon heating at 500 and 600 °C. K₂O and Li₂O doping conducted at 500 or 600 °C modified the degree of crystallinity and crystallite size of all phases present which consisted of a mixture of nanocrystalline α- and γ-Fe₂O₃ together with K₂FeO₄ and LiFe₅O₈ phases. However, the heavily Li₂O-doped sample consisted only of LiFe₅O₈ phase. The specific surface area of the system investigated decreased to an extent proportional to the amount of K₂O and Li₂O added. On the other hand, the catalytic activity was found to increase by increasing the amount of K₂O and Li₂O added. The maximum increase in the catalytic activity, expressed as the reaction rate constant (k) measured at 200 °C, attained 30.8% and 26.5% for K₂O and Li₂O doping, respectively. The doping process did not modify the activation energy of the catalyzed reaction but rather increased the concentration of the active sites without changing their energetic nature.     

Effect of Bi2O3 on structure and wetting studies of Bi2O3-ZnO-B2O3 glasses

Glasses with different Bi₂O₃ contents (37-42 mol%) have been prepared by conventional melt quench technique. The IR and Raman studies indicate that these glasses are made up of [BiO₆], [BiO₃], [BO₃] and [BO₄] basic structural units. The vibrations of [BiO₃] and [BO₃] become stronger as the content of Bi₂O₃ increases, which makes glass structure loosened. Viscosity of the glasses was measured by using a Rheotronic III paralleled plate rheometry, which shows that the viscosity of glass samples decreased when the content of Bi₂O₃ increased at the same temperature (400-460 °C). The temperature range which suits for glasses sealing was calculated by using the approximation of Arrhenian behaviour. The wetting performance of Bi₂O₃-ZnO-B₂O₃ glasses was described by using high-temperature microscope, which also proves that the structure of investigated Bi₂O₃-ZnO-B₂O₃ glasses become loosened due to the increasing of the content of Bi₂O₃.     

Mg-Ta2O5纳米棒涂层的制备、表征及其体外生物活性

采用两步水热处理的方法对钽进行表面改性,在其表面获得具有较小棒间距的掺镁氧化钽纳米棒阵列。通过改变镁元素的掺杂量,观察纳米棒形貌及微观结构的变化。在水热过程中,最佳的乙酸镁溶液浓度为0.05 mol/L,Mg在氧化钽纳米棒膜层中的含量达到4.25at%,以Mg~(2+)形式掺杂入Ta_2O_5纳米棒。使用AFM测量Ta、Ta_2O_5纳米棒和Mg-Ta_2O_5纳米棒样品的粗糙度,发现相比于纯钽片,Ta_2O_5纳米棒涂层和Mg-Ta_2O_5纳米棒涂层的粗糙度有所增加。ICP结果表明,生理盐水中镁离子的析出速率呈现先大幅度增加后变缓的趋势。在体外生物活性测试中,Ta_2O_5纳米棒涂层直到12 d后依然不能诱导出磷灰石;而Mg-Ta_2O_5纳米棒涂层表面不到8 d已经出现沉积磷灰石,Mg-Ta_2O_5纳米棒涂层有效地改善了钽基体表面的生物活性。