Characterising the loading direction sensitivity of 3D woven composites: Effect of z-binder architecture

Three different architectures of 3D carbon fibre woven composites (orthogonal, ORT; layer-to-layer, LTL; angle interlock, AI) were tested in quasi-static uniaxial tension. Mechanical tests (tensile in on-axis of warp and weft directions as well as 45° off-axis) were carried out with the aim to study the loading direction sensitivity of these 3D woven composites. The z-binder architecture (the through-thickness reinforcement) has an effect on void content, directional fibre volume fraction, mechanical properties (on-axis and off-axis), failure mechanisms, energy absorption and fibre rotation angle in off-axis tested specimens. Out of all the examined architectures, 3D orthogonal woven composites (ORT) demonstrated a superior behaviour, especially when they were tested in 45° off-axis direction, indicated by high strain to failure (∼23%) and high translaminar energy absorption (∼40 MJ/m³). The z-binder yarns in ORT architecture suppress the localised damage and allow larger fibre rotation during the fibre “scissoring motion” that enables further strain to be sustained by the in-plane fabric layers during off-axis loading.     

Mode I interlaminar fracture toughness properties of advanced textile fibreglass composites

The Mode I interlaminar fracture toughness properties of vinyl ester-based composites reinforced with fibreglass manufactured by the advanced textile technologies of braiding, knitting, stitching and through-the-thickness weaving are assessed in comparison to a variety of traditional composites made from fibreglass such as unidirectional or woven rovings. The interlaminar fracture toughness (G_Ic) of braided and knitted composites are higher than traditional composites by factors of more than two and four, respectively. Toughening in these textile composites was caused by extensive crack branching as the interlaminar crack was forced to follow a tortuous path through the complex fibre architectures. The G_Ic values of the composites reinforced in the through-thickness direction by weaving or stitching were higher than traditional composites by factors of nearly two and three, respectively, with the main toughening mechanism being crack bridging by the through-thickness binder yarns/stitches. A review of Mode I interlaminar fracture data collected from papers shows that advanced textile techniques are capable of manufacturing composites with substantially improved delamination resistance.     

2D and 3D imaging of fatigue failure mechanisms of 3D woven composites

A detailed investigation of the failure mechanisms for angle-interlocked (AI) and modified layer-to-layer (MLL) three dimensional (3D) woven composites under tension–tension (T–T) fatigue loading has been conducted using surface optical microscopy, cross-sectional SEM imaging, and non-destructive X-ray computed tomography (CT). X-ray microCT has revealed how cracks including surface matrix cracks, transverse matrix cracks, fibre/matrix interfacial debonding or delamination develop, and has delineated the complex 3D morphology of these cracks in relation to fibre architecture. For both weaves examined, transverse cracks soon become uniformly distributed in the weft yarns. A higher crack density was found in the AI composite than the MLL composite. Transverse cracking initiates in the fibre rich regions of weft yarns rather than the resin rich regions. Delaminations in the failed MLL specimen were more extensive than the AI specimen. It is suggested that for the MLL composite that debonding between the binder yarns and surrounding material is the predominant damage mechanism.     

Comparison of Interlaminar Fracture Toughness in Unidirectional and Woven Roving Marine Composites

This paper investigates the effect of fibre lay-up and matrix toughness on mode I and mode II interlaminar fracture toughness (G_Ic and G_IIc) of marine composites. Unidirectional and woven roving fibres were used as reinforcements. Two vinyl ester resins with different toughness were used as matrices. Results from both modes showed toughness variation that is consistent with matrix toughness. Values of G_Ic were not significantly influenced by fibre lay-up except at peak load points in the woven roving/brittle-matrix composite. Each peak load point, caused by interlocked bridging fibres, signified the onset of unstable crack growth. For unidirectional specimens, crack growth was stable and G_Ic statistically more reliable than woven roving specimens, which gave fewer G_Ic values due to frequent unstable crack growth. Mode II tests revealed that, except for crack initiation, G_IIc was higher in woven roving composites. This was due to fibre bridging, perpendicular to the crack growth direction, which encouraged stable crack growth and increased energy absorption. Mode II R-curves were obtained for the woven roving specimens. These R-curves provide additional information useful for characterising delamination resistance. The paper concludes that composites with woven roving fibres show similar mode I delamination characteristics to the unidirectional composites; but their mode II delamination characteristics, after crack initiation, are quite different.     

Composite toughness enhancement with interlaminar reinforcement

An experimental investigation of a newly proposed through-thickness reinforcement approach aimed to increase interlaminar toughness of laminated composites is presented. The approach alters conventional methods of creating three-dimensional fiber-reinforced polymer composites in that the reinforcing element is embedded into the host laminate after it has been cured. The resulting composite is shown to possess the benefits of a uniform surface quality and consolidation of the original unreinforced laminate. This technique was found to be highly effective in suppressing the damage propagation in delamination double-cantilever beam (DCB) test samples under mode I loading conditions. Pullout testing of a single reinforcing element was carried out to understand the bridging mechanics responsible for the improved interlaminar strength of reinforced laminate and stabilization and/or arrest of delamination crack propagation. The mode I interlaminar fracture of reinforced DCB samples was modeled using two-dimensional cohesive finite-element scheme to support interpretation of the experiments.     

Finite Element Analysis of Delamination inWoven Composites under Quasi-Static Indentation

Delamination initiation and propagation in plain woven laminates and 3D orthogonal woven composites during short beam shear (SBS) test were analyzed using finite element (FE) analyses. Two kinds of 3D woven composites, containing single z-yarns and double z-yarns, were considered. The FE models were guided by experimental observations from SBS tests for the same material systems. A series of mechanisms including creation and evolution of matrix cracks and delaminations were modeled discretely. The force-displacement curves obtained from the FE simulations were compared with those from experiments. Further parametric studies were conducted to investigate the effects of z-yarns and interlaminar fracture toughness on delamination in woven composites. The results from the FE simulations revealed that z-yarns in 3D woven composites can play a major role in impeding propagation of interlaminar cracks. On the other hand 2D plain woven laminates without any z-reinforcement demonstrated higher interlaminar fracture toughness due to undulation in yarns. 3D woven composites with double yarns showed better damage tolerance than single yarn 3D woven composites and their behavior was very similar to composite laminates with high interlaminar fracture toughness.     

Evaluation of the integrity of 3D orthogonal woven composites with embedded polymer optical fibers

Due to their high flexibility, high tensile strain and high fracture toughness, polymer optical fibers (POF) are excellent candidates to be utilized as embedded sensors for structure health monitoring of fiber reinforced composites. In 3D orthogonal woven structures yarns are laid straight and polymer optical fiber can be easily inserted during preform formation either as a replacement of constituents or between them. The results of the previous paper indicated how an optic fiber sensor can be integrated into 3D orthogonal woven preforms with no signal loss. This paper addresses whether incorporating POF into 3D orthogonal woven composites affects their structure integrity and performance characteristics. Range of 3D orthogonal woven composites with different number of layers and different weft densities was fabricated. The samples were manufactured with and without POF to determine the effect of embedding POF on composite structure integrity. Bending, tensile strength tests, and cross section analysis were conducted on the composite samples. Results revealed that integrity of 3D orthogonal woven composite was not affected by the presence of POF. Due to its high strain, embedded POF was able to withstand the stresses without failure as a result of conducting destructive tests of the composite samples. Micrograph of cross-section of composite samples showed that minimum distortion of the yarn cross-section in vicinity of POF and no presence of air pocked around the embedded POF which indicates that 3D woven preform provided a good host for embedded POF.     

Influence of z-pin length on the delamination fracture toughness and fatigue resistance of pinned composites

The effect of z-pin length on the mode I and mode II delamination toughness and fatigue resistance of z-pinned carbon-epoxy composites is investigated. Experimental testing and mechanical modelling reveals that both the mode I fracture toughness and fatigue resistance increase with the z-pin length due to increased bridging traction loads generated by elastic stretching and pull-out of the pins. The opposite trend occurs for mode II toughness, which decreases with increasing z-pin length due to lower traction loads arising from restrictions on the shear-induced rotation and pull-out of the pins. The mode II fatigue resistance is increased by z-pinning, although it is not dependent on the z-pin length. Increasing the z-pin length beyond a critical size also changes the mode I and mode II delamination fracture and fatigue processes from single to multiple cracking. The effect of z-pin length on the delamination toughening and fatigue strengthening mechanisms is determined.     

Mechanical and thermal properties of carbon fiber/polypropylene composite filled with nano-clay

The effect of organoclay on the mechanical and thermal properties of woven carbon fiber (CF)/compatibilized polypropylene (PPc) composites is investigated. Polypropylene–organoclay hybrids nanocomposites were prepared using a maleic anhydride-modified PP oligomer (PP-g-MA) as a compatibilizer. Different weight percentages of Nanomer® I-30E nanoclay were dispersed in PP/PP-g-MA (PPc) using a melt mixing method. The PPc/organoclay nanocomposite was then used to manufacture plain woven CF/PPc nanocomposites using molding compression process. CF/PPc/organoclay composites were characterized by different techniques, namely; dynamic mechanical analysis (DMA), fracture toughness and scanning electron microscope. The results revealed that at filler content 3% of organoclay, initiation and propagation interlaminar fracture toughness in mode I were improved significantly by 64% and 67% respectively, which could be explained by SEM at given weight as well; SEM images showed that in front of the tip, fibers pull out during initiation delamination accounting for fracture toughness improvement. Dynamic mechanical analysis showed enhancement in thermomechanical properties. With addition 3 wt.% of organoclay, the glass transition temperature increased by about 6 °C compared to neat CF/PPc composite indicating better heat resistance with addition of organoclay.     

Mechanical characterization of hierarchical carbon fiber/nanofiber composite laminates

Susceptibility to matrix driven failure is one of the major weaknesses of continuous-fiber composites. In this study, helical-ribbon carbon nanofibers (CNF) were dispersed in the matrix phase of a continuous carbon fiber-reinforced composite. Along with an unreinforced control, the resulting hierarchical composites were tested to failure in several modes of quasi-static testing designed to assess matrix-dominated mechanical properties and fracture characteristics. Results indicated CNF addition offered simultaneous increases in tensile stiffness, strength and toughness while also enhancing both compressive and flexural strengths. Short-beam strength testing resulted in no apparent improvement while the fracture energy required for the onset of mode I interlaminar delamination was enhanced by 35%. Extrinsic toughening mechanisms, e.g., intralaminar fiber bridging and trans-ply cracking, significantly affected steady-state crack propagation values. Scanning electron microscopy of delaminated fracture surfaces revealed improved primary fiber–matrix adhesion and indications of CNF-induced matrix toughening.     

Monotonic and cyclic short beam shear response of 3D woven composites

Monotonic, multi-step and cyclic short beam shear tests were conducted on 2D and 3D woven composites. The test results were used to determine the effect of z-yarns on the inter-laminar shear strength as well as the multi-loading behavior. The presence of z-yarns was found to affect not only the inter-laminar shear strength of the composite but also the behavior of the composite beyond the elastic limit. Microscopic examination of the damaged specimens revealed large delamination cracks in 2D woven composites while delamination cracks were hindered by z-yarns in 3D composites. This crack arrest phenomena resulted in a reduction in inter-laminar crack lengths and a higher distribution of the micro-cracks throughout the 3D composite. The multi-step and cyclic loading tests are found to be useful in the monitoring of specimen behavior during short beam shear testing. The induced damage was quantified in terms of the loss of strength and stiffness during each loading cycle. It was found that while the 2D composites have higher damage resistance, the 3D composites have a higher damage tolerance.     

Review of z-pinned composite laminates

This paper reviews published research into polymer composite laminates reinforced in the through-thickness direction with z-pins. Research into the manufacture, microstructure, delamination resistance, damage tolerance, joint strength and mechanical properties of z-pinned composites is described. Benefits of reinforcing composites with z-pins are assessed, including improvements to the delamination toughness, impact damage resistance, post-impact damage tolerance and through-thickness properties. Improvements to the failure strength of bonded and bearing joints due to z-pinning are also examined. The paper also reviews research into the adverse effects of z-pins on the in-plane mechanical properties, which includes reduced elastic modulus, strength and fatigue performance. Mechanisms responsible for the reduction to the in-plane properties are discussed, and techniques to minimise the adverse effect of z-pins are described. The benefits and drawbacks of z-pinning on the interlaminar toughness, damage tolerance and in-plane mechanical properties are compared against other common types of through-thickness reinforcement for composites, such as 3D weaving and stitching. Gaps in our understanding and unresolved research problems with z-pinned composites are identified to provide a road map for future research into these materials.     

Bridging effect on mode I fatigue delamination behavior in composite laminates

This paper discusses the bridging effect of fibres on mode I fatigue delamination growth in unidirectional and multidirectional polymer composite laminates based on a series of double cantilever beam (DCB) tests. From the results, there is sufficient evidence that fibre bridging can decrease the crack growth rate da/dN significantly, and using only one fatigue resistance curve to determine the delamination behavior in composite materials with large-scale fibre bridging may be inadequate. The bridging created in fatigue delamination is different from that of quasi-static delamination at the same crack length. So it is incorrect to use the resistance curve (R-curve) from quasi-static delamination tests to normalize fatigue delamination results.     

Enhancement of delamination fatigue resistance in carbon nanotube reinforced glass fiber/polymer composites

We show that the addition of small volume fractions of multi-walled carbon nanotubes (CNTs) to the matrix of glass–fiber composites reduces cyclic delamination crack propagation rates significantly. In addition, both critical and sub-critical inter-laminar fracture toughness values are increased. These results corroborate recent experimental evidence that the incorporation of CNTs improve fatigue life by a factor of two to three in in-plane cyclic loading. We show that in both the critical and sub-critical cases, the degree of delamination suppression is most pronounced at lower levels of applied cyclic strain energy release rate, ΔG. High-resolution scanning electron microscopy of the fracture surfaces suggests that the presence of the CNTs at the delamination crack front slows the propagation of the crack due to crack bridging, nanotube fracture, and nanotube pull-out. Further examination of the sub-critical fracture surfaces shows that the relative proportion of CNT pull-out to CNT fracture is dependent on the applied cyclic strain energy, with pull-out dominating as ΔG is reduced. The conditions for crack propagation via matrix cracking and nanotube pull-out and fracture are studied analytically using fracture mechanics theory and the results compared with data from the experiments. It is believed that the shift in the fracture behavior of the CNTs is responsible for the associated increase in the inter-laminar fracture resistance that is observed at lower levels of ΔG relative to composites not containing CNTs.     

Fracture toughness of weft-knitted fabric composites

The mode I inter-laminar fracture toughness of advanced knitted textile composites was investigated. Two complex weft-knitted glass fabrics were selected for the study: a triple rib knit and a Milano knit were impregnated with a tough epoxy resin and tested using a double cantilever beam geometry. For both knitted composites, the influence of the growth direction was studied by investigating crack propagation in both the wale and course directions. The fracture toughness was quantified by determining the critical strain energy release rate (G_IC) using the modified beam theory. The specimens had to be stiffened with layers of glass woven composites added on top and bottom of the beams. This was necessary in order to avoid plastic deformation of the beams and crack deviation out of the inter-laminar plane. The results clearly showed that knitted fabric composites have exceptional inter-laminar fracture toughness properties, namely, more than 7000 J/m². The origin of the high G_IC values, which are superior to woven or UD laminates, lies in the very complex fabric architecture. The three-dimensional loop structure induces various energy consuming mechanisms, which do not occur in other composites. Toughening mechanisms such as crack branching, friction, yarn bridging and breakage were identified using scanning electron microscopy.     

Investigating the Potential of Using Off-Axis 3D Woven Composites in Composite Joints’ Applications

The effect of circular notch has been evaluated for three different architectures of three-dimensional (3D) carbon fibre woven composites (orthogonal, ORT; layer-to-layer, LTL; angle interlock, AI) through open-hole quasi-static tension and double-lap bearing strength tests in the off-axis (45°) direction. Damage characterisation is monitored using Digital Image correlation (DIC) for open-hole testing and X-ray Computed Tomography (CT) for double-lap bearing strength test. The off-axis notched 3D woven composites exhibits minor reduction (less than 10 %) of the notched strength compared to the un-notched strength. DIC strain contour clearly show stress/strain localisation regions around the hole periphery and stress/strain redistribution away from the whole due to the z-binder existence, especially for ORT architecture. Up to 50 % bearing strain, no significant difference in the bearing stress/bearing strain response is observed. However when ORT architecture was loaded up to failure, it demonstrates higher strain to failure (~140 %) followed by AI (~105 %) and lastly LTL (~85 %). X-ray CT scans reveal the effect of the z-binder architecture on damage evolution and delamination resistance. The study suggests that off-axis loaded 3D woven composites, especially ORT architecture, has a great potential of overcoming the current challenges facing composite laminates when used in composite joints’ applications.     

Experimental investigation and finite element modeling of mixed-mode delamination in a moisture-exposed carbon/epoxy composite

An investigation of the effects of moisture on mixed-mode I/II delamination growth in a carbon/epoxy composite is presented. Experimental quasi-static and fatigue delamination tests were carried out on composite specimens. The quasi-static fracture test results showed that exposure to moisture led to a decrease in mode II and mixed-mode delamination toughness while mode I toughness was enhanced. The fatigue tests revealed an adverse effect of moisture on delamination growth under mixed-mode loadings. Existing delamination criteria and growth rate models were evaluated to determine which ones best predict delamination toughness and growth, respectively, at any given mixed-mode ratio. Quasi-static and fatigue simulations with a cohesive zone-based finite element model that incorporated the selected mixed-mode delamination models were performed and good agreement between experimental and numerical data was shown for dry and moisture-exposed specimens.     

Fracture toughness and fatigue crack growth behaviour of an Al2O3-SiC composite

The fracture toughness and fatigue crack growth characteristics of an Al₂O₃-SiC whisker composite were investigated. Quasi static fracture experiments were conducted on double edge-notched tension specimens and on four-point bend specimens containing a through-thickness Mode I crack which was introduced under uniaxial cyclic compression. The toughness results obtained using this procedure are more reproducible than those derived from the indentation technique and the notched bend bar method. The fracture toughness of the composite is about 60% higher than that of the unreinforced matrix material. Crack growth characteristics at room temperature were also investigated in notched plates of Al₂O₃-SiC subjected to fully compressive far-field cyclic loads. In the presence of a stress concentrator, this composite is found to be highly susceptible to fatigue crack growth under cyclic compressive loads.     

Environmental durability of z-pinned carbon fibre–epoxy laminate exposed to water

The influence of z-pins on the water absorption properties of a quasi-isotropic carbon fibre–epoxy laminate is assessed. Fibrous composite pins accelerate the moisture absorption rate and increase the total absorbed moisture concentration when the laminate is immersed in water. However, the moisture absorption properties of the laminate are not affected significantly by pins when exposed to hot and humid air. Water diffusion into the z-pinned laminate is aided by interfacial cracks between the pins and laminate. Also, the axial alignment of fibres within the composite pins in the through-thickness direction increases the water absorption rate. Pin pull-out tests reveal that water absorption reduces the mode I crack bridging traction load generated by pins by reducing the shear strength of the pin-laminate interface. This indicates that the mode I delamination toughness induced by pinning is weakened by moisture absorption.