Flow stress behavior and processing map of Al-Cu-Mg-Ag alloy during hot compression

The hot deformation behavior of Al-Cu-Mg-Ag was studied by isothermal hot compression tests in the temperature range of 573-773 K and strain rate range of 0.001-1 s^-1 on a Gleeble 1500 D thermal mechanical simulator. The results show the flow stress of Al-Cu-Mg-Ag alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. A hyperbolic sine relationship is found to correlate well the flow stress with the strain rate and temperature, the flow stress equation is estimated to illustrate the relation of strain rate and stress and temperature during high temperature deformation process. The processing maps exhibit two domains as optimum fields for hot deformation at different strains, including the high strain rate domain in 623-773 K and the low strain rate domain in 573-673 K.     

Deformation behavior and microstructure of an Al-Zn-Mg-Cu-Zr alloy during hot deformation

The hot deformation behavior and microstructures of Al-7055 commercial alloy were investigated by axisymmetric hot compression at temperatures ranging from 300°C to 450°C and strain rates from 10-2 to 10 s-1,respectively.Microstructures of deformed 7055 alloy were investigated by transmission electron microscopy (TEM).The dependence of peak stress on deformation temperature and strain rate can be expressed by the hyperbolic-sine type equation.The hot deformation activation energy of the alloy is 146 kJ/mol....     

Hot deformation behavior of FGH96 superalloys

1. Introduction Precipitation-hardened nickel-based superalloys have been widely used as high-temperature structural materials in gas turbine engine applications for more than 50 years. Because powder metallurgy (P/M) process produces a fine, homogenous a…     

Hot deformation behavior of Super304H austenitic heat resistant steel

The hot compression tests of Super304H austenitic heat resistant steel were carried out at 800-1200℃and 0.005-5 s~(-1) using a Gleeble 3500 thermal-mechanical simulator,and its deformation behavior was analyzed.The results show that the flow stress of Super304H steel decreases with the decrease of strain rate and the increase of deformation temperature;the hot deformation activation energy of the steel is 485 kJ/mol.The hot deformation equation and the relationship between the peak stress and the deforma...     

37Mn5钢热变形行为与流变应力模型研究

利用Gleeble-1500热模拟实验机研究37Mn5钢在变形温度为800～1150℃、变形速率为0．1～10s^-1条件下的热压缩变形行为。采用应变硬化率-应力曲线图较精确地获得峰值应力,并用双曲正弦方程描述37Mn5钢热压缩变形过程中的峰值应力与Zener—Hollomon参数的关系。回归分析得到方程中变形激活能及各材料常数的值,获得37Mn5钢在高温条件下的流变应力本构方程。结果表明,采用该本构方程计算出的流变应力值与实验所得应力值非常接近。     

Hot deformation behaviors and flow stress model of GCr15 bearing steel

The hot deformation behaviors of GCr15 bearing steel were investigated by isothermal compression tests, performed on a Gleeble-3800 thermal-mechanical simulator at temperatures between 950℃ and 1150℃ and strain rates between 0.1 and 10 s^-1. The peak stress and peak strain as functions of processing parameters were obtained. The dependence of peak stress on strain rate and temperature obeys a hyperbolic sine equation with a Zener-Hollomon parameter. By regression analysis, in the temperature range of 950-1 150℃ and strain rate range of 0.1-10 s^-1, the mean activation energy and the stress exponent were determined to be 351kJ/mol and 4.728, respectively. Meanwhile, models of flow stress and dynamic recrystallization （DRX） grain size were also established. The model predictions show good agreement with experimental results.     

Flow stress behavior of Al-Cu-Li-Zr alloy containing Sc during hot compression deformation

The flow stress behavior of Al-3.5Cu-1.5Li-0.25（Sc＋Zr） alloy during hot compression deformation was studied by isothermal compression test using Gleeble-1500 thermal-mechanical simulator. Compression tests were preformed in the temperature range of 653-773 K and in the strain rate range of 0.001-10 s^-1 up to a true plastic strain of 0.7. The results indicate that the flow stress of the alloy increases with increasing strain rate at a given temperature,and decreases with increasing temperature at a given imposed strain rate. The relationship between the flow stress and the strain rate and the temperature was derived by analyzing the experimental data. The flow stress is in a hyperbolic sine relationship with the strain rate,and in an Arrhenius relationship with the temperature,which imply that the process of plastic deformation at an elevated temperature for this material is thermally activated. The flow stress of the alloy during the elevated temperature deformation can be represented by a Zener-Hollomon parameter with the inclusion of the Arrhenius term. The values of n,α and A in the analytical expressions of flow stress σ are fitted to be 5.62,0.019 MPa^-1 and 1.51×10^16 s^-1,respectively. The hot deformation activation energy is 240.85 kJ/mol.     

Rheological behavior of continuous roll casting process of aluminum alloy

The rheological behavior of aluminum alloy and its influencing factors in physical simulation of continuous roll casting process were studied by using a Gleeble-1500 thermal-mechanical simulation tester with a set of special clamp system. The relationships between the flow stress and the strain rate in the deformation process of simulating roll casting experiment were obtained. The results show that four different characteristic stages exist in the temperature range of the whole rheological process. The first occurs when the temperature is higher than 600℃, which belongs to the creep deformation stage; the second occurs when the temperature lies in the range of 500 - 600℃, and it can be regarded as the high temperature and low stress level deformation stage; the third occurs when the temperature decreases to the range of 300 - 500℃, it is considered to be the middle stress level deformation stage; the last occurs when the temperature is less than 300℃ and the strain rate is less than 1.00 s^-1 , it belongs to middle stress level deformation stage. But when the strain rate is larger than 1.00 s^-1, it belongs to the high stress level deformation stage. And the relative constitutive models suitable for the four different stages of continuous roll casting process were established through multivariate linear regression analysis of the experimental data.     

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

The hot deformation behavior of an ultralow-carbon microalloyed steel was investigated using an MMS-200 thermal simulation test machine in a temperature range of 1 073-1 373 K and strain rate range of 0.01-10 s~(-1).The results show that the flow stress decreases with increasing deformation temperature or decreasing strain rate.The strain-compensated constitutive model based on the Arrhenius equation for this steel was established using the true stress-strain data obtained from a hot compression test.Furthermore,a new constitutive model based on the Z-parameter was proposed for this steel.The predictive ability of two constitutive models was compared with statistical measures.The results indicate the new constitutive model based on the Z-parameter can more accurately predict the flow stress of an ultralow-carbon microalloyed steel during hot deformation.The dynamic recrystallization (DRX) nucleation mechanism at different deformation temperatures was observed and analyzed by transmission electron microscopy (TEM),and strain-induced grain boundary migration was observed at 1 373 K/0.01 s~(-1).     

Hot deformation behavior and flow stress model of F40MnV steel

Single hit compression tests were performed at 1 223-1 473 K and strain rate of 0.1-10 s-1 to study hot deformation behavior and flow stress model of F40MnV steel. The dependence of the peak stress, initial stress, saturation stress, steady state stress and peak stain on Zener-Hollomon parameter were obtained. The mathematical models of dynamic recrystallization fraction and grain size were also obtained. Based on the tested data, the flow stress model of F40MnV steel was established in dynamic recovery region and dynamic recrystallization region, respectively. The results show that the activation energy for dynamic recrystallization is 278.6 kJ/mol by regression analysis. The flow stress model of F40MnV steel is proved to approximate the tested data and suitable for numerical simulation of hot forging.     

Property and microstructure analysis of ZK60 alloy superplastic sheet

It was investigated that the superplastic mechanical properties of fine-grained ZK60 magnesium alloy sheets at the temperature range of 200-420 ℃ and strain rate range of 5.56 × 10-4 -5.56 ×10-2 s-1 by tensile tests.And the microstructure evolution during the superplastic deformation of ZK60 magnesium alloy was examined by metallurgical microscope and transmission electronic microscope (TEM).The results showed that fine-grained ZK60 magnesium alloy starts to exhibit superplasticity from 250 ℃ and the maximum elongation is about 1106% at 400 ℃ and 5.56 × 10-4 s-1.The strain rate sensitivity is significantly enhanced with the increase of temperature and with the decrease of strain rate.The predominate superplastic mechanism of ZK60 magnesium alloy is grain boundary slide (GBS) at the temperature range of 300-400 ℃.The grains of ZK60 alloy remain equaxial after superplastic deformation,and dynamic continuous recrystallization (DCRX) is an important softening mechanism and grain stability mechanism during the superplastic deformation of the alloy.The curved grain boundaries and crumpled bands at grain boundaries after deformation prove GBS generates during superplastic deformation of ZK60 magnesium alloy.     

Research on constitutive equation of DIWA353 steel used in hemisphere head of power station nearby recrystallization temperature

To simulate the DIWA353 steel used in boiler nearby recrystallization temperature accurately by using finite element,the high temperature constitutive model of this material must be researched firstly....     

Dynamic recrystallization during hot torsion of Al-4Mg alloy

Binary Al-4Mg alloy have been deformed by hot torsion at 300-500℃ and strain rates of 0.006-1.587 s of 5.5. The specimens were annealed in vacuum for 1.5 h at 500℃ and then water quenched. The study indicates that the dynamic recrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter (Zener-Hollmon Parameter), i.e. 19.3 ≤ InZ ≤ 24.8. Increasing the strain rate at higher deformation temperature or reducing the strain rate at lower deformation temperature accelerates the occurrence of dynamic recrystallization in the alloy.     

Hot Deformation Kinetics of Magnesium Alloy AZ31

1 IntroductionManyirreplaceable characteristics andthe abundanceof magnesiumalloyin nature have drawn a world wide at-tentionin 21st century.In contrast with the cast magne-siumalloy,wrought magnesiumalloyis much betterinitscomprehensive mechanical properties ,so a wide applica-tionis found in many fields like transportation,aeronau-tics ,electricity and communication.The flowstress of a material depends upontwo majorfactors ,namely,its own characteristics and its deforma-tionterms .The basic …     

Al-Mg-Si合金热压缩变形的流变应力方程

为了给制定和优化热加工工艺参数提供理论依据,采用Gleeble-1500热模拟机研究了含锆Al-Mg-Si合金在变形温度为653~803 K、变形速率为0.01~10s^-1条件下的热压缩变形的流变应力行为,并通过回归法建立材料变形的流变应力数学模型.结果表明：该合金为正应变速率敏感材料,真应力-真应变曲线存在明显的稳态流变特征;流变应力随着变形速率的增加以及变形温度的降低而增加;在较低变形温度条件下,真应力〖CDF*3〗真应变曲线为动态回复曲线;在较高变形温度条件下真应力-真应变曲线为动态再结晶曲线.该合金流变应力σ可用包含Arrhenius项的Zener Hollomon参数的函数来描述,式中A、α和n的值分别为1.89×10¹⁰s^-1、0.024MPa^-1和7.46,热变形激活能Q为166.85kJ/mol.     

Hot deformation behaviour and processing maps of AA6061-10 vol.% SiC composite prepared by spark plasma sintering

AA6061-10 vol.% SiC composite was successfully prepared by spark plasma sintering. The deformation behaviour of this composite was studied using the uniaxial compression test, which was conducted at temperatures between 300 and 500°C and strain rates between 0.001 and 1 s-1. Results indicate that the stress-strain curves of the AA6061-10 vol.% SiC composite typically feature dynamic recrystallization. The steady stress can be described by a hyperbolic sine constitutive equation, and the activation energy of the composite is 230.88 k J/mol. The processing map was established according to the dynamic materials model. The optimum hot deformation temperature is 450–500°C and the strain rate is 1–0.1 s-1. The instability zones of flow behaviour can also be identified using the processing map.     

7055铝合金高温压缩变形的流变应力

在Gleeble 1500热模拟试验机上,采用高温等温压缩试验,研究了7055铝合金在250～450℃温度范围内压缩变形的流变应力变化规律.结果表明,应变速率和变形温度的变化强烈影响合金的流变应力,流变应力随变形速率的提高而增大;随变形温度的提高而降低.7055铝合金高温变形时的流变应力可用Zener Hollomon参数来描述.     

挤压温度对固相再生ZM6镁合金组织和性能的影响

利用固相再生方法在挤压比为25：1的条件下,将ZM6镁合金屑分别在350℃、400℃、450℃和500℃温度下制备成试样,进行微观组织观察和力学性能测试。结果表明：当挤压温度为400℃时,ZM6耐热镁合金没有发生再结晶,合金中金属化合物在挤压过程中被打碎,均匀分布在基体中;当挤压温度为450℃和500℃时,ZM6镁合金发生部分动态再结晶;随着挤压温度的提高,合金的抗拉强度和延伸率提高;在挤压温度为500℃,合金的抗拉强度、屈服强度和延伸率分别为300．2MPa、142．9MPa和30％。合金室温拉伸断口主要表现为穿晶韧窝断裂。     

316LN热变形行为及动态再结晶晶粒的演变规律

采用热压缩试验研究了316LN不锈钢在温度1250℃-900℃,应变速率0．005s^-1～0．5s^-1,变形程度50％条件下的变形行为和组织演变;分析了变形参数对应力-应变曲线的影响规律,计算获得了该钢热变形应力指数和激活能;并通过动态再结晶晶粒演变规律的研究,建立了该钢热变形动态再结晶图,以及动态再结晶晶粒演变规律模型。研究结果可为316LN不锈钢锻造过程晶粒细匀化的控制提供科学的依据。     

高温振动下聚四氟乙烯垫片的松弛与泄漏测试

设计了一种高温下垫片密封性能的测试系统,研究了在100 ℃时小幅位移控制振动及静态松弛条件下聚四氟乙烯垫片的应力松弛和密封性能,并讨论了载荷比为0.99时3种最大压缩量对聚四氟乙烯垫片的动态应力松弛和泄漏行为的影响,以及在同上最大压缩量下的静态应力松弛和密封性能. 结果表明,100 ℃下聚四氟乙烯垫片的动态应力松弛率随最大压缩量增大而增大,静态应力松弛率随最大压缩量增大有缓慢减小;在静态和动态试验的初始20 s阶段内,应力迅速下降,表现明显的应力松弛,而动态试验更明显;动态松弛实验前后的压差变化约是静态松弛试验的1.1倍.