共查询到18条相似文献,搜索用时 437 毫秒
1.
2.
基于单胞模型镍基单晶高温合金低周疲劳寿命的预测 总被引:1,自引:0,他引:1
基于镍基单晶高温合金的微观尺度结构特征,建立了γ/γ′双相单胞有限元模型,并基于能量耗散理论,引入统一表征非对称载荷循环特性和拉/扭多轴效应的k参量,以循环塑性应变能作为损伤参量,建立了镍基单晶高温合金低周疲劳寿命预测模型;分别利用宏观有限元模型和γ/γ′双相单胞微观有限元模型对[001]取向的DD3、PWA1480和CMSX-2镍基单晶高温合金的单轴、多轴低周疲劳试验过程进行数值模拟。结果表明:微观单胞有限元模型反映了试验合金的微观结构特性,其预测精度明显优于宏观有限元模型的;上述3种合金几乎所有的试验数据分别落在1.3,2.0和2.0倍偏差分布带内。 相似文献
3.
一种镍基单晶合金高温低周疲劳寿命预测方法 总被引:2,自引:0,他引:2
《机械强度》2015,(5):857-862
提出一种考虑平均应力、应变比和晶体取向的镍基单晶合金低周疲劳寿命预测方法。首先建立镍基单晶合金在[001]和[111]晶体取向下的疲劳寿命预测模型,该模型考虑了平均应力和应变比对疲劳寿命的影响。然后,通过引入晶体取向函数建立不同晶体取向与[001]和[111]晶体取向下寿命预测模型中疲劳参数的关系,从而考虑镍基单晶合金晶体取向对疲劳寿命的影响。最后,提出通过[001]和[111]晶体取向下的模型来预测任意晶体取向下疲劳寿命的方法。提出的方法用DD3和PWA1840镍基单晶合金高温低周疲劳寿命试验数据进行验证,结果表明提出的方法是可接受的。 相似文献
4.
喷丸强化处理工艺可以显著提高金属材料的抗疲劳和抗应力腐蚀等性能,这与喷丸后在金属表面层形成的残余应力场紧密相关,因此对喷丸残余应力的大小及分布进行预测具有重要意义。对近年国内外喷丸残余应力场的有限元模拟进行评述,总结出6种典型的残余应力分析模型,分别是二维轴对称模型、四对称面模型、三对称面模型、双对称面模型、单对称面模型和无对称边界条件的有限元模型,比较了不同模型的特点及应用现状。介绍了当前几种新的残余应力分析有限元模型:随机三维模型和周期性边界条件模型,根据其原理和特点认为其本质是无对称边界条件模型和对称边界条件有限元模型的延伸。针对空化水喷丸、激光喷丸和超声波喷丸等新工艺,新喷丸过程的数值模拟一般是以机械喷丸工艺的数值模拟方法为基础进行改进,主要采用弹丸撞击法和等效载荷法。对未来喷丸残余应力数值模拟研究进行了展望,认为从组织强化角度深入研究喷丸强化机理、建立更符合实际喷丸工艺的有限元模型、开发新算法以及将有限元法和离散元法进行结合是值得关注的研究方向。 相似文献
5.
镍基单晶高温合金蠕变-疲劳寿命评估方法进展 总被引:3,自引:0,他引:3
论述镍基单晶合金的滑移变形机制和疲劳裂纹萌生机理,分别介绍镍基单晶合金蠕变寿命和低循环疲劳寿命分析评估模型;镍基单晶合金蠕变、疲劳寿命的研究方法可分为应用各向异性张量描述非弹性各向异性变形的宏观力学(唯象)模型和基于晶体学滑移变形理论的微观力学模型;晶体取向、平均应力、环境温度、循环频率、循环应力比是影响单晶合金蠕变-疲劳寿命的主要因素。复杂应力状态下的单晶合金多轴低循环疲劳损伤,单晶合金在疲劳-蠕变交互作用下的疲劳损伤和单晶合金的接触疲劳损伤等问题是需要研究的重要课题。 相似文献
6.
针对难加工材料镍基高温合金切削力大以及难排屑等问题,在ABAQUS有限元分析软件中建立三维斜角仿真模型,模拟镍基高温合金的切削加工过程。研究斜角切削状态下镍基高温合金材料的去除机理和切屑形成,通过正交试验和单因素试验,分析在不同切削参数下流屑角以及三维切削力的变化情况。采用有限元分析方法对镍基高温合金的三维斜角切削过程进行仿真研究,降低了研究成本,为镍基高温合金高效切削加工提供了理论参考。 相似文献
7.
为研究预应力条件对镍基高温合金切削加工的影响,采用Abaqus/Explicit软件建立了预应力切削镍基高温合金的三维有限元模型,研究了不同预应力状态下的切削力和加工表面各向应力的分布规律,分析了预应力条件对切屑形状、切削力和表面残余应力的影响,并与实验结果进行对比。研究结果表明:预应力作用对切削力和切屑形状的影响不显著;预应力作用对与预应力加载方向相同的已加工表面应力影响最大,并随着预应力的增大此方向上应力的分布层深显著增大,而对其他方向上的应力分布影响不显著;在一定范围内,随着预应力的增大已加工表面残余压应力值大小和分布层深都显著增大。 相似文献
8.
9.
10.
喷丸三维残余应力场的有限元模拟 总被引:14,自引:1,他引:13
运用大型有限元计算软件ABAQUS建立了模拟喷丸残余应力场的三维有限元模型,预测了在相同喷丸强度下玻璃丸和钢丸两种类型弹丸喷射所产生的残余应力场。模拟过程中,分析了线性减缩积分单元的沙漏参数、材料的应变硬化率、喷丸覆盖率以及初始残余拉应力等因素对304不锈钢靶材残余应力分布的影响。从计算结果可以看出,钢丸喷丸产生的残余压应力层较深,但在高覆盖率时,玻璃喷丸产生的残余压应力的平均值比钢丸喷丸处理后产生的大。在有初始残余拉应力(250 Mpa)存在的情况下,两种类型的喷丸处理均能使304不锈钢靶材表面形成残余压应力层,这说明喷丸工艺可以提高奥氏体不锈钢焊接构件的抗应力腐蚀开裂能力。本研究成果为进一步探讨喷丸强化不锈钢焊接头抗应力腐蚀性能的机理奠定了基础。 相似文献
11.
Low cycle fatigue tests were conducted on the single crystal nickel-based superalloy, DD6, with different crystallographic orientations (i.e., [001], [011], and [111]) and strain dwell types (i.e., tensile, compressive, and balanced types) at a certain high temperature. Given the material anisotropy and mean stress, both orientation factor and stress range were introduced to the Smith, Watson, and Topper (SWT) stress model to predict the fatigue life. Experimental results indicated that the fatigue properties of DD6 depend on both crystallographic orientation and loading types. The fatigue life of the tensile, compressive, and balanced strain dwell tests are shorter than those of continuous cycling tests without strain dwell because of the important creep effect. The predicted results of the proposed modified SWT stress method agree well with the experimental data. 相似文献
12.
The coupling effect of normal stress and shear stress on orthotropic materials happens when applied loading deflects from
the directions of the principal axes of the material coordinate system. By taking account of the coupling effects, formulas
of equivalent stress and strain for cubic single crystal materials are cited. Using the equivalent strain and equivalent stress
for such material and a variable k, which is introduced to express the effect of asymmetrical cyclic loading on fatigue life, a low cycle fatigue (LCF) life
prediction model for such material in multiaxial stress starts is proposed. On the basis of the yield criterion and constitutive
model of cubic single crystal materials, a subroutine to calculate the thermo elastic-plastic stress-strain of the material
on an ANSYS platform was developed. The cyclic stress-strain of DD3 notched specimens under asymmetrical loading at 680°C
was analyzed. Low cycle fatigue test data of the single crystal nickel-based superalloy are used to fit the different parameters
of the power law with multiple linear regression analysis. The equivalent stress and strain for a cubic single crystal material
as failure parameters have the largest correlation coefficient. A power law exists between k and the failure cycle. The model was validated with LCF test data of CMSX-2 and DD3 single crystal nickel-based superalloys.
All the test data fall into the factor of 2.5 for CMSX-2 hollow cylinder specimens and 2.0 scatter band for DD3 notched specimens,
respectively. 相似文献
13.
14.
Comparison and analysis of main effect elements of machining distortion for aluminum alloy and titanium alloy aircraft monolithic component 总被引:1,自引:0,他引:1
Y. Yang M. Li K. R. Li 《The International Journal of Advanced Manufacturing Technology》2014,70(9-12):1803-1811
Main effect elements of machining distortion for aluminum alloy and titanium alloy aircraft monolithic component are investigated by finite element simulation and experiment. Based on an analysis of milling process characters, finite element models of machining distortion are developed. Considering the action of initial residual stress, finite element simulation and analysis of machining distortion for aluminum alloy aircraft monolithic component are performed. Initial residual stress, cutting loads, and coupling action of these two effect factors are taken into account, respectively, to perform finite element simulations of machining distortion for titanium alloy aircraft monolithic component. The finite element simulation results are compared with experiment results and found to be in good agreement, indicating the validation of the proposed finite element models. The research results show that the initial residual stress in the blank is the main effect element of machining distortion for aluminum alloy aircraft monolithic component, while cutting loads (including cutting force and temperature) are the main effect element of machining distortion for titanium alloy aircraft monolithic component. To decrease machining distortion of aluminum alloy aircraft monolithic component, the initial residual stress in the blank must be controlled first. Similarly, to decrease machining distortion of titanium alloy aircraft monolithic component, the cutting loads must be controlled first. 相似文献
15.
铝合金预拉伸板在成型过程中会产生较大的残余应力,在切削过程中毛坯的初始残余应力的释放对整体结构件的宏观变形有重要的影响。在弹塑性力学的基础上,综合运用Hypermesh和ABAQUS建立残余应力单因素作用下的三维铣削仿真加工变形场的有限元模型,利用生死单元技术模拟了材料的去除,分析了铝合金板材材料去除过程中残余应力释放引起的加工变形规律。并且运用Hypermesh提高了有限元前处理的速度,解决了复杂模型的残余应力加载困难与单元去除困难的问题。 相似文献
16.
17.
18.
扫描电子束铝合金表面处理应力场仿真与试验验证 总被引:1,自引:0,他引:1
研究扫描电子束铝合金表面处理应力场的分布规律,对了解残余应力的形成机理具有十分重要的理论及实际意义。在热弹塑性理论的基础上建立电子束表面处理应力场的有限元模型,分析高温热力学参数对电子束表面处理应力场的影响;通过仿真与试验验证相结合的方法确定材料的高温热力学参数,得到铝合金电子束表面扫描后的应力分布规律。随着弹性模量和切变模量的增加,ADC12铝合金材料表面的变形量和最大应力均成非线性增加。经电子束表面处理后试样表面扫描带附近为拉应力,而在其他位置为压应力;最大拉应力出现在扫描带的内侧边缘处,外侧边缘次之,而扫描带中间的拉应力最小;最大表面应力为127.6 MPa,变形量为1.8 mm。 相似文献