Film formation from pigmented latex systems: Drying kinetics and bulk morphologies of ground calcium carbonate/functionalized poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) blend films

The drying kinetics and bulk morphology of pigmented latex films obtained from poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) latex particles functionalized with carboxyl groups and ground calcium carbonate blends were studied. Latex/pigment blends with higher carboxyl group coverage on the latex particle surfaces dried faster than films with few or no carboxyl groups present. The latex/pigment dispersions also dried faster when there was more stabilizer present in the blend system because of the hydrophilic nature of the stabilizer. The net effect of increasing the pigment volume concentration in the blend system was to shorten the drying time. The bulk morphologies of the freeze‐fractured surfaces of the pigmented latex films were studied with scanning electron microscopy. Scanning electron microscopy analysis showed that increased surface coverage of carboxyl groups on the latex particles in the latex/pigment blends resulted in the formation of smaller pigment aggregates with a more uniform size distribution in the blend films. In addition, the use of smaller latex particles in the blends reduced the ground calcium carbonate pigment aggregate size in the resulting films. Scanning electron microscopy analysis also showed that when the initial stabilizer coverage on the latex particles was equal to 18%, smaller aggregates of ground calcium carbonate were distributed within the copolymer matrix of the blend films in comparison with the cases for which the initial stabilizer coverage on the latex particles was 8 or 36%. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2267–2277, 2006     

Mechanical properties of films prepared from model high‐glass‐transition‐temperature/low‐glass‐transition‐temperature latex blends

The mechanical properties of films prepared from model high‐glass‐transition‐temperature (T_g)/low‐T_g latex blends were investigated with tensile testing and dynamic mechanical analysis. Polystyrene (PS; carboxylated and noncarboxylated) and poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) [P(BMA/BA); noncarboxylated] were used as the model high‐T_g and low‐T_g latexes, respectively. Carboxyl groups were incorporated into the PS latex particles to alter their surface properties. It was found that the presence of carboxyl groups on the high‐T_g latex particles enhanced the Young's moduli and the yield strength of the PS/P(BMA/BA) latex blend films but did not influence ultimate properties, such as the stress at break and maximum elongation. These phenomena could be explained by the maximum packing density of the PS latex particles, the particle–particle interfacial adhesion, and the formation of a “glassy” interphase. The dynamic mechanical properties of the latex blend films were also investigated in terms of the carboxyl group coverage on the PS latex particles; these results confirmed that the carboxyl groups significantly influenced the modulus through the mechanism of a glassy interphase formation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2788–2801, 2002     

Mechanical properties of latex blends films from polystyrene particles with different sizes in a butyl acrylate‐co‐styrene copolymer matrix

Blends of polystyrene (PSt) hard particle latex with three different particle sizes (96, 72, and 61 nm) and a n‐butyl acrylate‐co‐styrene (BA‐co‐St) copolymer soft latex with a 204 nm particle size were synthesized by emulsion polymerization. Latexes were standardized at 25% solids and blended at different concentrations by wt% of PSt:BA‐co‐St for every hard particle size. Finally, films from each blend were obtained. Morphology of each film prepared was examined by transmission electron microscopy, and it was found that the hard particles are randomly distributed in the films inside the copolymer matrix. The effect on mechanical properties of different PSt concentrations and particle sizes was assessed by DMA as a function of temperature. The results indicate that rigidity of the blended latex increases as the particle size diminishes as determined by the reduction in damping in the tan δ peak. The storage modulus increases as the concentration of PSt increases in the blends and the values depend upon the size of PSt particles. Mechanical properties at tension indicate that decreasing the size of the PSt particles and increasing their concentration increase the Young's modulus and ultimate strength at tension because of an increase in the rigidity of the films. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Influence of particle surface properties on film formation from precipitated calcium carbonate/latex blends

The surface properties of films prepared from a blend of precipitated calcium carbonate pigment (PCC) and poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) [P(BMA/BA); T_g = 0°C] latex were investigated in terms of the surface characteristics of the PCC and P(BMA/BA) latex particles. It was found that the presence of carboxyl groups on the P(BMA/BA) latex particles significantly improved the uniformity of the distribution of the PCC particles within the P(BMA/BA) copolymer matrix and the gloss of the resulting films. This phenomenon could be explained by an acid‐base reaction between the PCC particles and the carboxylated P(BMA/BA) latex particles. Studies on the influence of the composition of PCC/P(BMA/BA) latex blends on the gloss and transparency of the films were also performed, which led to the determination of the critical pigment volume concentration (CPVC) of this system, which was found to be 42 vol %. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 891–900, 2002     

Surface treatment and characterization of functionalized latex particles and inorganic pigment particles used in the study of film formation from pigmented latex systems

The adsorption of sodium polyacrylate [NaPA] on noncarboxylated and carboxylated poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) [P(BMA/BA)] latexes and ground calcium carbonate (GCC) was studied. The adsorption isotherms of NaPA on P(BMA/BA) latex surfaces showed that NaPA tended to adsorb to a greater extent onto the latex particle surfaces when the carboxyl group surface coverage of latex polymer particles is low, which indicates a repulsive interaction between the dissociated carboxyl groups and NaPA macroions. The electrophoretic mobility of cleaned model P(BMA/BA) latexes decreased with the increasing carboxyl group surface coverage at pH 10 due to the alkali‐swelling characteristics of carboxylated latexes. For GCC, used as extender pigment particles in the pigmented latex blend systems, the size of the GCC pigment particles stabilized with NaPA decreased during a sonification process and their ζ‐potential became increasingly negative with the addition of NaPA to the GCC pigment slurry. Particle size and ζ‐potential measurements showed that NaPA can stabilize GCC particles effectively, and the optimum concentration of NaPA to stabilize GCC is around 1 wt % based on solid GCC. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 398–404, 2006     

Miscibility behavior of poly(n‐butyl methacrylate) latex films containing alkali‐soluble resin

The dynamic mechanical properties of poly(n‐butyl methacrylate) (PBMA) latex films postadded with alkali‐soluble resin (ASR) have been studied and compared with those of latex films prepared by emulsion polymerization in the presence of ASR (ASR‐fortified latex). The miscibility between PBMA and ASR, poly(styrene/alpha‐methylstyrene/acrylic acid) (SAA), was found to influence the dynamic mechanical behavior of the films. The dynamic properties of PBMA latex films postadded with SAA show two distinct damping peaks, which correspond to those of PBMA and SAA, respectively, in the phase‐separated state. The SAA migrates onto film surface during film formation and, as a result SAA preserved their domains in the matrix phase, showing two distinct relaxations in the dynamic mechanical spectrum. On the other hand, the ASR‐fortified films exhibit single damping peak. SAA‐fortified latex particles would be core/shell structured, and the miscibility between PBMA and SAA is clearly improved by the grafting reaction between PBMA and SAA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 639–649, 2000     

Film formation from polystyrene–poly(butyl acrylate‐co‐methyl methacrylate) latex blends

We have employed steady sate fluorescence (SSF) and UV‐visible (UVV) techniques to determine the film formation behavior of latex blends. Blend films were prepared from mixtures of a high‐T_g pyrene (P) labeled polystyrene (PS) latex and a low‐T_g copolymer of poly(butyl acrylate‐co‐methyl methacrylate) (BuA/MMA4). Eleven different blend films were prepared in various hard/soft latex compositions at room temperature and annealed at elevated temperatures above glass‐transition (T_g) temperature of polystyerene for 10 min. Fluorescence intensity (I_P) from P was measured after each annealing step to monitor the stages of film formation. The evolution of transparency of latex films was monitored using photon transmission intensity, I_tr. Film morphologies were examined by atomic force microscopy (AFM). A significant change occurs in both I_P and I_tr intensities at a certain critical weight fraction of hard latex (R_c = 0.3). Above R_c, two distinct film formation stages, which are named as void closure and interdiffusion processes, were seen in fluorescence data. Transparency of the films was decreased with decreasing PS content, indicating that a phase separation process occurs between PS and BuA/MMA4 phases by thermal treatment, which results in turbid films. However, below R_c, no change was observed in I_P and I_tr upon annealing, whereas transparency increased overall with increasing BuA/MMA4 ratio. We explained this result as the phase separation process between PS and BuA/MMA4 blends. These results were also confirmed by AFM pictures. Film formation stages above R_c were modeled and related activation energies were calculated. POLYM. COMPOS., 27:431–442, 2006. © 2006 Society of Plastics Engineers     

胶乳的作用及对纸张涂料性能的影响

胶乳加到高岭土悬浮液中能瓦解片状高岭土的聚集 ,提高了涂料的多分散性 ,同时增加了涂料的稳定性。胶乳在涂料中起到粘接颜料粒子及颜料与纸基的作用 ,增强涂层强度。胶乳的粒径和形状、胶乳的稳定性及玻璃化温度等特性影响涂料粘度、流变性等性能。在预涂涂布中 ,选择由高苯乙烯含量聚合的羧基丁苯胶乳可提高涂层抗拉毛强度及纸面光泽度和平滑度 ,有利于面涂涂布     

Preparation and properties of poly[styrene‐co‐(butyl acrylate)‐co‐(acrylic acid)]/silica nanocomposite latex prepared using an acidic silica sol

BACKGROUND: Polyacrylate/silica nanocomposite latexes have been fabricated using blending methods with silica nanopowder, in situ polymerization with surface‐functionalized silica nanoparticles or sol–gel processes with silica precursors. But these approaches have the disadvantages of limited silica load, poor emulsion stability or poor film‐forming ability. RESULTS: In this work, poly[styrene‐co‐(butyl acrylate)‐co‐(acrylic acid)] [P(St‐BA‐AA)]/silica nanocomposite latexes and their dried films were prepared by adding an acidic silica sol to the emulsion polymerization stage. Morphological and rheological characterization shows that the silica nanoparticles are not encapsulated within polymer latex particles, but interact partially with polymer latex particles via hydrogen bonds between the silanol groups and the ? COOH groups at the surface of the polymer particles. The dried nanocomposite films have a better UV‐blocking ability than the pure polymer film, and retain their transparency even with a silica content up to 9.1 wt%. More interestingly, the hardness of the nanocomposite films increases markedly with increasing silica content, and the toughness of the films is not reduced at silica contents up to 33.3 wt%. An unexpected improvement of the solvent resistance of the nanocomposite films is also observed. CONCLUSION: Highly stable P(St‐BA‐AA)/silica nanocomposite latexes can be prepared with a wide range of silica content using an acidic silica sol. The dried nanocomposite films of these latexes exhibit simultaneous improvement of hardness and toughness even at high silica load, and enhanced solvent resistance, presumably resulting from hydrogen bond interactions between polymer chains and silica particles as well as silica aggregate/particle networks. Copyright © 2009 Society of Chemical Industry     

Encapsulation of titanium dioxide in styrene/n‐butyl acrylate copolymer by miniemulsion polymerization

Miniemulsion copolymerization of styrene/n‐butyl acrylate was investigated as a means of encapsulating hydrophilic titanium dioxide (TiO₂) in a film‐forming polymer. Dispersion studies of the TiO₂ were first carried out to determine the choice of stabilizer, its concentration, and the dispersion process conditions for obtaining stable TiO₂ particles with minimum particle size. Through screening studies of various functional stabilizers and shelf‐life stability studies at both room and polymerization temperatures, Solsperse 32,000 was selected to give relatively small and stable TiO₂ particles at 1 wt % stabilizer and with 20–25 min sonification. The subsequent encapsulation of the dispersed TiO₂ particles in styrene/n‐butyl acrylate copolymer (St/BA) via miniemulsion polymerization was carried out and compared with a control study using styrene monomer alone. The lattices resulting from the miniemulsion encapsulation polymerizations were characterized in terms of the encapsulation efficiencies (via density gradient column separations; DGC) and particle size (via dynamic light scattering). Encapsulation efficiencies revealed that complete encapsulation of all of the TiO₂ by all of the polymer was not achieved. The maximum encapsulation efficiencies were 79.1% TiO₂ inside 61.7% polystyrene and 63.6% TiO₂ inside 38.5% St/BA copolymer. As the density of the particles collected from the DGC increased from one layer to another, both the average particle size and the number of the TiO₂ particles contained in each latex particle increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3479–3486, 2006     

Preparation and properties of core [poly(styrene‐n‐butyl acrylate)]–shell [poly(styrene–methyl methacrylate–vinyl triethoxide silane)] structured latex particles with self‐crosslinking characteristics

Structured latex particles with a slightly crosslinked poly(styrene‐n‐butyl acrylate) (PSB) core and a poly(styrene–methacrylate–vinyl triethoxide silane) (PSMV) shell were prepared by seed emulsion polymerization, and the latex particle structures were investigated with Fourier transform infrared, thermogravimetric analysis, differential scanning calorimetry, transmission electron microscopy, and dynamic light scattering. The films that were formed from the structured core (PSB)–shell (PSMV) particles under ambient conditions had good water repellency and good tensile strength in comparison with films from structured core (PSB)–shell [poly(styrene–methyl methyacrylate)] latex particles; this was attributed to the self‐crosslinking of CH₂?CH? Si(OCH₂CH₃)₃ in the outer shell structure. The relationship between the particle structure and the film properties was also investigated in this work. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1824–1830, 2006     

Synthesis of core‐shell fluoroacrylate copolymer latex via emulsion polymerization and its application in ink‐jet ink

Core‐shell fluoroacrylate copolymer latex was synthesized via semicontinuous seed emulsion polymerization, in which ethyl acrylate was utilized to prepare core, and methyl methacrylate, butyl acrylate, methacrylate acid, and hexafluorobutyl methacrylate were employed to constitute the shell. So the yielded latex particles had the soft core and hard shell. Multifunction and low viscosity of the latex had been applied as the binder of latex inks. The ζ potential showed that the latex particles had high thermodynamic stability. The latex and latex inks exhibited viscosity plateau of Newtonian fluid behaviors. Rheological tests revealed that viscous behaviors dominated in the latex and latex inks. However, there was some interaction among the latex and pigment particles. The hydrophobicity of the cast films of the latex increased with the amount of the fluoroacrylate monomer. Fluorine tended to migrate to the interface between the cast film and air. Therefore, the hydrophobicity was derived from the fluorine enrichment phenomena on the top side of the cast films. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

聚丙烯酸酯/铜酞菁蓝复合乳胶膜中颜料颗粒的分散状态

引言功能颗粒存在下,水性胶乳在织物、纸张、皮革等目标基质表面的焙烘成膜是众多生产领域中普遍存在着的一个固化成型过程。通常认为功能颗粒在乳胶膜内初级粒子形式的均匀稳定分散可赋予涂层最佳的功能性和黏结牢度[1]。但目前常见的、基     

Complexation of poly(dimethylsiloxane)/poly(methyl methacrylate‐co‐butyl acrylate‐co‐methacrylic acid) latex with poly(dimethylsiloxane)/poly(vinyl acetate‐co‐butyl acrylate) latex

Two latices—the poly(dimethylsiloxane) (PDMS)/poly(methyl methacrylate‐co‐butyl acrylate‐co‐methacrylic acid) system (PA latex) and the PDMS/poly(vinyl acetate‐co‐butyl acrylate) system (PB latex)—were prepared by seeded emulsion polymerization, and PA/PB complex latices were obtained through the interparticle complexation of the PA latex with the PB latex. In addition, for the further study of the interparticle complexation of the PA latex with the PB latex, copolymer latices [PDMS/methyl methacrylate‐co‐butyl acrylate‐co‐vinyl acetate‐co‐methacrylic acid) (PC)] were prepared according to the monomer recipe of the complex latices and the polymerization process of the component latices. The properties of the obtained polymer latices and complex latices were investigated with surface‐tension, contact‐angle, and viscosity measurements. The mechanical properties of the coatings obtained from the latices were investigated with tensile‐strength measurements. The results showed that, in comparison with the two component latices (PA latex and PB latex) and the corresponding copolymer latices (PC latices), the PA/PB complex latices had lower surface tension, lower viscosities, and better wettability to different substrates. The tensile strengths of the coatings obtained from the complex latices were higher than the tensile strengths of the coatings from the two component latices and copolymer latices. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2522–2527, 2004     

Preparation and properties of core–shell nanosilica/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) latex

A core–shell nanosilica (nano‐SiO₂)/fluorinated acrylic copolymer latex, where nano‐SiO₂ served as the core and a copolymer of butyl acrylate, methyl methacrylate, and 2,2,2‐trifluoroethyl methacrylate (TFEMA) served as the shell, was synthesized in this study by seed emulsion polymerization. The compatibility between the core and shell was enhanced by the introduction of vinyl trimethoxysilane on the surface of nano‐SiO₂. The morphology and particle size of the nano‐SiO₂/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) [P(MMA–BA–TFEMA)] core–shell latex were characterized by transmission electron microscopy. The properties and surface energy of films formed by the nano‐SiO₂/P(MMA–BA–TFEMA) latex were analyzed by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, and static contact angle measurement. The analyzed results indicate that the nano‐SiO₂/P(MMA–BA–TFEMA) latex presented uniform spherical core–shell particles about 45 nm in diameter. Favorable characteristics in the latex film and the lowest surface energy were obtained with 30 wt % TFEMA; this was due to the optimal migration of fluorine to the surface during film formation. The mechanical properties of the films were significantly improved by 1.0–1.5 wt % modified nano‐SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Sintering of latex particles in pigmented coatings. II. Influence of the latex particle size

The light-scattering coefficient S of coatings formulated from a mixture of an inorganic pigment and polystyrene latex particles may be enhanced significantly when the dry coating is heated in order to cause sintering of the polystyrene spheres. The relative increase in S depends on the size and the amount of the latex particles and the type of the inorganic pigment. Of the latexes examined (0.5, 0.2, 0.1, and 0.03 μm in diameter) the 0.2μm latex is the most effective in blends with platelike delaminated clay. The coatings based on spherelike precipitated calcium carbonate are less responsive to the heat treatment. The gloss of the clay–latex coatings is not significantly altered by the heat treatment up to 20 pph of latex; the gloss of the calcium carbonate coatings generally decreases upon heating.     

Effect of colophony emulsion on the adhesive properties of vinyl acetate/n‐butyl acrylate copolymeric latex

We prepared a novel copolymeric latex of vinyl acetate and n‐butyl acrylate (V‐B) using a semibatch emulsion polymerization process. The glass‐transition temperature (T_g), steady viscosity, flow activation energy (E_f), dynamic moduli, and amphiphilic properties of the V‐B latex in the presence of colophony were systematically investigated. The experimental results demonstrate that excellent adhesive behaviors were achieved for the V‐B latex blended with 20 wt % colophony, whereas good adhesive performance was related to the moderate T_g, viscosity, E_f, storage modulus, and low contact angle on the adherent. The debonding mechanisms for V‐B and its colophony‐modified latexes were analyzed. A possible mechanism for the V‐B latex blended with colophony emulsion was determined. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of poly(styrene‐co‐butyl acrylate)/montmorillonite nanocomposite by emulsion polymerization: Characterization and nanoscratch behavior

Organic–inorganic hybrid poly(styrene‐co‐butyl acrylate)/organically modified montmorillonite (PSBA/organo‐MMT) latex particles have been prepared by in situ emulsion polymerization. The effects of modifier variety and the level of organo‐MMT have been investigated on the basis of the characteristics and mechanical properties of the resulting hybrid emulsion polymers. Although the more hydrophilic intercalated organic modifiers increased the latex particle size, the hydrophobic ones decreased the particle size. A more heterogeneous copolymer chain intercalation was seen by widespread XRD reflection as the organo‐MMT (organoclay) level increases. The tapping mode atomic force microscopy (AFM) and transmission electron microscopy (TEM) were used to determine the dispersion state of organoclay particles inside the nanocomposite copolymer films. Dynamic mechanical thermal analysis (DMTA) showed that adding the organoclay to the copolymer decreased the maximum loss tangent (tanδ) value and caused the shift to a lower temperature. Interestingly, the incorporation of organoclay decreased the glass storage modulus of the copolymer, while increased the rubbery storage modulus to some extent. In addition, a standard indenter for the nanoscratching of copolymer nanocomposite films was used under low applied loads of 150 and 250 μN. The nanoscratch results showed that incorporation of a 3 wt % hydrophobic organoclay, e.g., Closite15A, in the copolymer matrix enhanced considerably the near‐surface hardness and grooving resistance of the nanocomposite film at room temperature. In fact, copolymer nanocomposite films with higher near‐surface hardness and tanδ curve broadening exhibited more nanoscratch resistance through a specific variety of viscoelastic deformation, which did not create a bigger groove. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of aqueous polyurethane dispersions with well‐defined soft segments

Novel aqueous polyurethane (PU) hybrid dispersions were successfully prepared with 5–15 mol % functionalized hexamethylene diisocynate trimer modified by N‐(n‐butyl)‐3‐aminopropyltriethoxysilane and dihydroxylpropyl‐terminated siloxane oligomers (TS). The results of the differential scanning calorimetry and X‐ray diffraction tests show that the degree of segment order was reduced by the introduction of TS. The hybrid polymer films with TS introduced into the PU backbone displayed excellent water and xylene resistance. Atomic force microscopy showed that the films had a smooth surface. It was noticeable that the tensile strength (σ_b) and Young's modulus of the films increased simultaneously when TS was incorporated into PU; σ_b of the PU15 film with 15 mol % TS was much higher than that of the neat PU0 film, and the breaking elongation of the film with 10 mol % TS was clearly higher than that of the other films. The results indicate that an appropriate content of TS significantly improved the properties of the aqueous PU hybrids. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Dispersion polymerization of n‐butyl acrylate

The dispersion polymerization of n‐butyl acrylate (BA) was investigated using alcohol/water mixtures as the dispersion medium, 4,4′ ‐azobis‐(4‐cyanopentanoic acid) as the initiator, and polyvinylpyrrolidone (PVP) as the stabilizer. The effects of polymerization parameters, such as the alcohol/water ratio in the medium and the type and concentration of the polymeric stabilizer, on the resulting particle size and size distribution were studied. The final particle size and the stability of the dispersion system were found to be greatly influenced by the type of alcohol used in the mixture; that is, methanol or ethanol, even though the apparent solubility parameters are almost the same for the two types of mixtures. Poly(butyl acrylate) particles with controlled size and size distribution (monodisperse), and gel content were successfully prepared in a 90/10 methanol/water medium. It was found that the particle size decreased with increasing initiator concentration. This is the opposite of what was previously reported in the dispersion polymerizations of styrene and methyl methacrylate. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2692–2709, 2002