Removal of chromium (VI) from aqueous solution using treated oil palm fibre

This study proposed an oil palm by-product as a low-cost adsorbent for the removal of hexavalent chromium [Cr (VI)] from aqueous solution. Adsorption of Cr (VI) by sulphuric acid and heat-treated oil palm fibre was conducted using batch tests. The influence of pH, contact time, initial chromium concentration and adsorbent dosage on the removal of Cr (VI) from the solutions was investigated. The optimum initial pH for maximum uptake of Cr (VI) from aqueous solution was found to be 1.5. The removal efficiency was found to correlate with the initial Cr (VI) concentration, adsorbent dosage as well as the contact time between Cr (VI) and the adsorbent. The adsorption kinetics tested with pseudo first order and pseudo second order models yielded high R(2) values from 0.9254 to 0.9870 and from 0.9936 to 0.9998, respectively. The analysis of variance (ANOVA) showed significant difference between the R(2) values of the two models at 99% confidence level. The Freundlich isotherm (R(2)=0.8778) described Cr (VI) adsorption slightly better than the Langmuir isotherm (R(2)=0.8715). Difficulty in desorption of Cr (VI) suggests the suitability of treated oil palm fibre as a single-use adsorbent for Cr (VI) removal from aqueous solution.     

Error analysis of equilibrium studies for the almond shell activated carbon adsorption of Cr(VI) from aqueous solutions

In this study, the preparation of activated carbon from almond shell with H2SO4 activation and its ability to remove toxic hexavalent chromium from aqueous solutions are reported. The influences of several operating parameters such as pH, particle size and temperature on the adsorption capacity were investigated. Adsorption of Cr(VI) is found to be highly pH, particle size and temperature dependent. Four adsorption isotherm models namely, Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich were used to analyze the equilibrium data. The Langmuir isotherm provided the best correlation for Cr(VI) onto the almond shell activated carbon (ASC). Adsorption capacity was calculated from the Langmuir isotherm as 190.3 mg/g at 323 K. Thermodynamic parameters were evaluated and the adsorption was endothermic showing monolayer adsorption of Cr(VI). Five error functions were used to treat the equilibrium data using non-linear optimization techniques for evaluating the fit of the isotherm equations. The highest correlation for the isotherm equations in this system was obtained for the Freundlich isotherm. ASC is found to be inexpensive and effective adsorbent for removal of Cr(VI) from aqueous solutions.     

Removal of Cr(VI) from industrial wastewaters by adsorption Part I: determination of optimum conditions

Aim of this study is the determination of the Cr(VI) removal efficiency of treated pine sawdust and also to find out the thermodynamic and kinetic parameters of Cr(VI) removal process in batch systems. Sawdust has been treated with 1,5-disodium hydrogen phosphate before the adsorption experiments. The effects of initial concentration of Cr(VI) ion, temperature, amount of adsorbent and pH of the solution on adsorption have been investigated. Optimum conditions for adsorption were determined as T=40 degrees C, sawdust dose=4 g, pH 2, by using the results of these experiments and an additional set of experiments was performed under these optimum conditions in order to see the change in the adsorption efficiency. Removal of chromium ion was found as highly dependent on pH and initial Cr(VI) concentration of the solution. In order to find out thermodynamic and kinetic parameters equilibrium adsorption models were applied. Although experimental data confirm with both Langmuir and Freundlich isotherm models, they suit most on Langmuir isotherms. Adsorption rate constant was determined from Lagergren equation. Equilibrium constants, adsorption free energy, enthalpy and entropy change values were also determined. It was found that adsorption process follows first order kinetic and adsorption of Cr(VI) on sawdust has the spontaneous nature.     

Removal of Cr(VI) from aqueous solutions using pre-consumer processing agricultural waste: a case study of rice husk

This paper reports the feasibility of using pre-consumer processing agricultural waste to remove Cr(VI) from synthetic wastewater under different experimental conditions. For this, rice husk, has been used after pre-treatments (boiling and formaldehyde treatment). Effect of various process parameters, namely, pH, adsorbent dose, initial chromium concentration and contact time has been studied in batch systems. The removal of chromium was dependent on the physico-chemical characteristics of the adsorbent, adsorbate concentration and other studied process parameters. Maximum metal removal was observed at pH 2.0. The efficiencies of boiled and formaldehyde treated rice husk for Cr(VI) removal were 71.0% and 76.5% respectively for dilute solutions at 20gl(-1) adsorbent dose. The experimental data were analyzed using Freundlich, Langmuir and Dubinin-Radushkevich (D-R) isotherm models. It was found that Freundlich and D-R models fitted well. The results revealed that the hexavalent chromium is considerably adsorbed on rice husk and it could be an economical method for the removal of hexavalent chromium from aqueous systems. FTIR and SEM were recorded, before and after adsorption, to explore number and position of the functional groups available for Cr(VI) binding on to studied adsorbents and changes in adsorbent surface morphology.     

Adsorption of Cr(VI) from aqueous solutions by spent activated clay

Adsorption of Cr(VI) onto spent activated clay (SAC), a waste produced from an edible oil refinery company, was investigated for its beneficial use in wastewater treatment. After pressure steam treatment, SAC was used as an adsorbent. The adsorption kinetic data were analyzed and fitted well in a pseudo-first-order equation and the rate of removal was found to speed up with decreasing pH and increasing temperature. Activation energy for the adsorption process was found to be 4.01–5.47 kcal/K mol. The Langmuir adsorption isotherm was used to fit the equilibrium data and the effect of pH, temperature and ionic strength were studied. The maximum adsorption capacities for Cr(VI) ranged from 0.743 to 1.422 mg/g for temperature between 4 and 40 °C under a condition of pH 2.0. The studies conducted show the process of Cr(VI) removal to be spontaneous at high temperature and endothermic in nature. From the waste utilization and environment point of view, the work carried out is important and useful. Results obtained can serve as baseline data for designing a treatment process using this low-cost adsorbent for the treatment of wastewater rich in Cr(VI).     

Hexavalent chromium removal from wastewater using aniline formaldehyde condensate coated silica gel

A resinous polymer, aniline formaldehyde condensate (AFC) coated on silica gel was used as an adsorbent in batch system for removal of hexavalent chromium from aqueous solution by considering the effects of various parameters like reaction pH, dose of AFC coated silica gel, initial Cr(VI) concentration and aniline to formaldehyde ratio in AFC synthesis. The optimum pH for total chromium [Cr(VI) and Cr(III)] adsorption was observed as 3. Total chromium adsorption was second order and equilibrium was achieved within 90-120 min. Aniline to formaldehyde ratio of 1.6:1 during AFC synthesis was ideal for chromium removal. Total chromium adsorption followed Freundlich's isotherm with adsorption capacity of 65 mg/g at initial Cr(VI) 200mg/L. Total chromium removal was explained as combinations of electrostatic attraction of acid chromate ion by protonated AFC, reduction of Cr(VI) to Cr(III) and bond formation of Cr(III) with nitrogen atom of AFC. Almost 40-84% of adsorbed chromium was recovered during desorption by NaOH, EDTA and mineral acids. AFC coated silica gel can be effectively used for treatment of chromium containing wastewaters as an alternative.     

Biosorption of chromium(VI) ion from aqueous solutions using walnut, hazelnut and almond shell

The potential to remove Cr(VI) ion from aqueous solutions through biosorption using, the shells of Walnut (WNS) (Juglans regia), Hazelnut (HNS) (Corylus avellana) and Almond (AS) (Prunus dulcis) was investigated in batch experiments. The equilibrium adsorption level was determined to be a function of the solution contact time and concentration. Kinetic experiments revealed that the dilute chromium solutions reached equilibrium within 100 min. The biosorptive capacity of the shells was dependent on the pH of the chromium solution, with pH 3.5 being optimal. Adsorption of Cr(VI) ion uptake is in all cases pH-dependent showing a maximum at equilibrium pH values between 2.0 and 3.5, depending on the biomaterial, that correspond to equilibrium pH values of 3.5 for (WNS), 3.5 for (HNS) and 3.2 for (AS). The adsorption data fit well with the Langmuir isotherm model. The sorption process conformed to the Langmuir isotherm with maximum Cr(VI) ion sorption capacities of 8.01, 8.28, and 3.40 mg/g for WNS, HNS and AS, respectively. Percentage removal by WNS, HNS and AS was 85.32, 88.46 and 55.00%, respectively at a concentration of 0.5 mM. HNS presented the highest adsorption capacities for the Cr(VI) ion.     

Kinetics and thermodynamic of adsorption of chromium(VI) from aqueous solution using puresorbe

This paper deals with an investigation on coir-based adsorbent, puresorbe, in the removal of chromium(VI) from the aqueous solutions. The adsorption of chromium(VI) was carried out by varying the parameters such as agitation time, metal concentration, adsorbent dose, temperature and pH. The experimental isotherm data were analyzed using Langmuir, Freundlich and Redlich and Peterson isotherms. Adsorption followed second order rate expression for the particle size 250–500 μm at pH 2. The monolayer adsorption capacity is 76.92 mg chromium(VI) per gram of puresorbe. Thermodynamic parameters show the endothermic nature of chromium(VI) adsorption. Desorption study carried out using distilled water adjusted to pH of 2–10, suggests that chemisorption might be the mode of adsorption.     

Trivalent chromium removal from wastewater using low cost activated carbon derived from agricultural waste material and activated carbon fabric cloth

An efficient adsorption process is developed for the decontamination of trivalent chromium from tannery effluents. A low cost activated carbon (ATFAC) was prepared from coconut shell fibers (an agricultural waste), characterized and utilized for Cr(III) removal from water/wastewater. A commercially available activated carbon fabric cloth (ACF) was also studied for comparative evaluation. All the equilibrium and kinetic studies were conducted at different temperatures, particle size, pHs, and adsorbent doses in batch mode. The Langmuir and Freundlich isotherm models were applied. The Langmuir model best fit the equilibrium isotherm data. The maximum adsorption capacities of ATFAC and ACF at 25 degrees C are 12.2 and 39.56 mg/g, respectively. Cr(III) adsorption increased with an increase in temperature (10 degrees C: ATFAC--10.97 mg/g, ACF--36.05 mg/g; 40 degrees C: ATFAC--16.10 mg/g, ACF--40.29 mg/g). The kinetic studies were conducted to delineate the effect of temperature, initial adsorbate concentration, particle size of the adsorbent, and solid to liquid ratio. The adsorption of Cr(III) follows the pseudo-second-order rate kinetics. From kinetic studies various rate and thermodynamic parameters such as effective diffusion coefficient, activation energy and entropy of activation were evaluated. The sorption capacity of activated carbon (ATFAC) and activated carbon fabric cloth is comparable to many other adsorbents/carbons/biosorbents utilized for the removal of trivalent chromium from water/wastewater.     

Synthesis of ordered large-pore mesoporous carbon for Cr(VI) adsorption

Highly ordered mesoporous carbon with large accessible pores (OMC-P) was prepared by using laboratory-made poly(ethylene oxide)-b-polystyrene diblock copolymer as template via the evaporation-induced self-assembly method. The OMC-P was first used as adsorbent for removal of Cr(VI) ion from aqueous solution. Adsorption behavior was studied as a function of time, concentration of adsorbate, temperature, and pH. The kinetics of adsorption of Cr(VI) ion onto OMC-P is well fit to the pseudo-second order model. The Cr(VI) ion adsorption is favored at lower temperatures and at initial acid pH values in the equilibrium. The Freundlich and the Langmuir isotherm fit the equilibrium data satisfactorily. The influence of porosity on equilibrium adsorption capacity was investigated on three types of carbon materials, namely, OMC-P, ordered mesoporous carbon templated from amphiphilic triblock copolymer F127 (OMC-F) and commercial activated carbon (AC). The prepared OMC-P exhibits much higher adsorption performance than the other two carbons.     

Grape waste as a biosorbent for removing Cr(VI) from aqueous solution

Grape waste generated in wine production is a cellulosic material rich in polyphenolic compounds which exhibits a high affinity for heavy metal ions. An adsorption gel was prepared from grape waste by cross-linking with concentrated sulfuric acid. It was characterized and utilized for the removal of Cr(VI) from synthetic aqueous solution. Adsorption tests were conducted in batch mode to study the effects of pH, contact time and adsorption isotherm of Cr(VI), which followed the Langmuir type adsorption and exhibited a maximum loading capacity of 1.91 mol/kg at pH 4. The adsorption of different metal ions like Cr(VI), Cr(III), Fe(III), Zn(II), Cd(II) and Pb(II) from aqueous solution at different pH values 1-5 has also been investigated. The cross-linked grape waste gel was found to selectively adsorb Cr(VI) over other metal ions tested. The results suggest that cross-linked grape waste gel has high possibility to be used as effective adsorbent for Cr(VI) removal.     

Application of dolochar in the removal of cadmium and hexavalent chromium ions from aqueous solutions

Dolochar, a waste material generated in sponge iron industry, is processed and put to test as an adsorbent for removal of Cd(II) and Cr(VI) ions from aqueous solutions. The dolochar samples were characterised to determine the different phases and their distribution by reflection microscopy. The analysis indicated that the sample consists of metallic iron, fused carbon, and Ca-Mg bearing phases (Ca-Mg-silicate-oxide) along with lots of voids and pores. The fixed carbon (FC) content of the material is 13.8% with a Langmuir surface area of 81.6 m²/g and micropore area of 34.1 m²/g. Batch adsorption experiments have been conducted to study the sorption behaviour of Cd(II) and Cr(VI) ions on dolochar as a function of particle size, contact time, adsorbent dosages, pH and temperature. It is observed that higher pH and temperature enhances sorption of Cd(II) ions. In contrast, the adsorption for Cr(VI) is found to be better in acidic pH in comparison to alkaline media. The equilibrium adsorption isotherm data are tested by applying both Langmuir and Freundlich isotherm models. It is observed that Langmuir isotherm model fitted better compared to the Freundlich model indicating monolayer adsorption. The thermodynamic parameters such as ΔG°, ΔH° and ΔS° indicate the effectiveness of dolochar to remove Cd(II) and Cr(VI) ions from aqueous solution. The kinetics of adsorption is found to better fit to pseudo second order reaction.     

Removal of chromium from aqueous solution by using oxidized multiwalled carbon nanotubes

The batch removal of hexavalent chromium (Cr(VI)) from aqueous solution by using oxidized multiwalled carbon nanotubes (MWCNTs) was studied under ambient conditions. The effect of pH, initial concentration of Cr(VI), MWCNT content, contact time and ionic strength on the removal of Cr(VI) was also investigated. The removal was favored at low pH with maximum removal at pH <2. The adsorption kinetics was modeled by first-order reversible kinetics, pseudo-first-order kinetics, pseudo-second-order kinetics, and intraparticle diffusion models, respectively. The rate constants for all these kinetic models were calculated, and the results indicate that pseudo-second-order kinetics model was well suitable to model the kinetic adsorption of Cr(VI). The removal of chromium mainly depends on the occurrence of redox reaction of adsorbed Cr(VI) on the surface of oxidized MWCNTs to the formation of Cr(III), and subsequent the sorption of Cr(III) on MWCNTs appears as the leading mechanism for chromium uptake to MWCNTs. The presence of Cr(III) and Cr(VI) on oxidized MWCNTs was confirmed by the X-ray photoelectron spectroscopic analysis. The application of Langmuir and Freundlich isotherms are applied to fit the adsorption data of Cr(VI). Equilibrium data were well described by the typical Langmuir adsorption isotherm. Overall, the study demonstrated that MWCNTs can effectively remove Cr(VI) from aqueous solution under a wide range of experimental conditions, without significant Cr(III) release.     

Chromium removal from electroplating wastewater by coir pith

Coir pith is a by-product from padding used in mattress factories. It contains a high amount of lignin. Therefore, this study investigated the use of coir pith in the removal of hexavalent chromium from electroplating wastewater by varying the parameters, such as the system pH, contact time, adsorbent dosage, and temperature. The maximum removal (99.99%) was obtained at 2% (w/v) dosage, particle size <75microm, at initial Cr(VI) 1647mgl(-1), system pH 2, and an equilibrium time of 18h. The adsorption isotherm of coir pith fitted reasonably well with the Langmuir model. The maximum Cr(VI) adsorption capacity of coir pith at 15, 30, 45 and 60 degrees C was 138.04, 197.23, 262.89 and 317.65mgCr(VI)g(-1) coir pith, respectively. Thermodynamic parameters indicated an endothermic process and the adsorption process was favored at high temperature. Desorption studies of Cr(VI) on coir pith and X-ray absorption near edge structure (XANES) suggested that most of the chromium bound on the coir pith was in Cr(III) form due to the fact that the toxic Cr(VI) adsorbed on the coir pith by electrostatic attraction was easily reduced to less toxic Cr(III). Fourier transform infrared (FT-IR) spectrometry analysis indicated that the carbonyl (CO) groups and methoxy (O-CH(3)) groups from the lignin structure in coir pith may be involved in the mechanism of chromium adsorption. The reduced Cr(III) on the coir pith surface may be bound with CO groups and O-CH(3) groups through coordinate covalent bonding in which a lone pair of electrons in the oxygen atoms of the methoxy and carbonyl groups can be donated to form a shared bond with Cr(III).     

Removal of chromium(III) from tannery wastewater using activated carbon from sugar industrial waste

Chromium is commonly found in huge quantities in tannery wastewaters. For this reason, the removal and recovery of the chromium content of tannery wastewaters is crucial for environmental protection and economic reasons. Removal and recovery of chromium were carried out by using low-cost potential adsorbents. For this purpose three types of activated carbon; C1, the waste generated from sugar industry as waste products and the others (C2, C3) are commercial granular activated carbon, were used. The adsorption process and extent of adsorption are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental condition. The effect of pH, particle size and different adsorbent on the adsorption isotherm of Cr(III) was studied in batch system. The sorption data fitted well with Langmuir adsorption model. The efficiencies of activated carbon for the removal of Cr(III) were found to be 98.86, 98.6 and 93 % for C1, C2 and C3, respectively. The order of selectivity is C1>C2>C3 for removal of Cr(III) from tannery wastewater. Carbon "C1" of the highest surface area (520.66 m(2)/g) and calcium content (333.3 mg/l) has the highest adsorptive capacity for removal of Cr(III). The results revealed that the trivalent chromium is significantly adsorbed on activated carbon collected from sugar industry as waste products and the method could be used economically as an efficient technique for removal of Cr(III) and purification of tannery wastewaters.     

Selective adsorption and separation of chromium (VI) on the magnetic iron-nickel oxide from waste nickel liquid

The selective adsorption of Cr (VI) from the wastewater of Cr (VI)-Ni (II) by magnetically iron-nickel oxide was investigated in this study. Synthetic iron-nickel oxide magnetic particles in the co-sedimentation method were used as adsorbent to remove hexavalent chromium ions. The characteristic of adsorption was evaluated by Langmuir, Freundlich isotherm and Dubinin-Kaganer-Radushkevich (DKR) equations in the simulation wastewater of Cr (VI)-Ni (II) bi-system. The energy spectra and FT-IR analysis were used to test adsorbent before and after adsorption. The obtained results suggest that the uptake of chromium (VI) effect is obvious from phosphate anions and that from others is unobvious. The maximum adsorption capacity of hexavalent chromium is about 30 mg/g at pH 5.00+/-0.02, and it was reduced by increasing the total dissolved substance (TDS) of system. Adsorption energies E are about 10.310-21.321 kJ/mol which were obtained from DKR equation in difference TDS conditions. The regeneration shows that the iron-nickel oxide has good reuse performance and the hexavalent chromium was recycled. The major adsorption mechanism proposed was the ions exchange; however the surface coordination was a main role in the condition of TDS less than 200mg/L.     

Chromium (VI) adsorption on boehmite

Boehmite was synthesized and characterized in order to study the adsorption behavior and the removal of Cr(VI) ions from aqueous solutions as a function of contact time, initial pH solution, amount of adsorbent and initial metal ion concentration, using batch technique. Adsorption data of Cr(VI) on the boehmite were analyzed according to Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption models. Thermodynamic parameters for the adsorption system were determinated at 293, 303, 313 and 323K temperatures. The kinetic values and thermodynamic parameters from the adsorption process show that the Cr(VI) ions adsorption on boehmite is an endothermic and spontaneous process. These results show that the boehmite could be considered as a potential adsorbent for chromium ions in aqueous solutions.     

Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent

Oak wood and oak bark chars were obtained from fast pyrolysis in an auger reactor at 400-450 °C. These chars were characterized and utilized for Cr(VI) remediation from water. Batch sorption studies were performed at different temperatures, pH values and solid to liquid ratios. Maximum chromium was removed at pH 2.0. A kinetic study yielded an optimum equilibrium time of 48 h with an adsorbent dose of 10 g/L. Sorption studies were conducted over a concentration range of 1-100mg/L. Cr(VI) removal increased with an increase in temperature (Q(Oak wood)(°): 25 °C = 3.03 mg/g; 35 °C = 4.08 mg/g; 45 °C = 4.93 mg/g and Q(Oakbark)(°): 25 °C = 4.62 mg/g; 35 °C = 7.43 mg/g; 45 °C = 7.51 mg/g). More chromium was removed with oak bark than oak wood. The char performances were evaluated using the Freundlich, Langmuir, Redlich-Peterson, Toth, Radke and Sips adsorption isotherm models. The Sips adsorption isotherm model best fits the experimental data [high regression (R(2)) coefficients]. The overall kinetic data was satisfactorily explained by a pseudo second order rate expression. Water penetrated into the char walls exposing Cr(VI) to additional adsorption sites that were not on the surfaces of dry char pores. It is remarkable that oak chars (S(BET): 1-3m(2)g(-1)) can remove similar amounts of Cr(VI) as activated carbon (S(BET): ～ 1000 m(2)g(-1)). Thus, byproduct chars from bio-oil production might be used as inexpensive adsorbents for water purification. Char samples were successfully used for chromium remediation from contaminated surface water with dissolved interfering ions.     

Removal of Cr(VI) from aqueous solutions by low-cost biosorbents: marine macroalgae and agricultural by-products

In this study, adsorption of Cr(VI) onto the four low-cost biosorbents (Laminaria japonica, P. yezoensis Ueda, rice bran and wheat bran) was investigated depending on solution pH, contact time, adsorbent concentration and adsorption isotherms by employing batch adsorption technique. The adsorption capacities were significantly influenced by solution pH, with lower pH favoring higher Cr(VI) removal for various biosorbents. The ionic strength of NaCl was also observed to have a significant impact on the Cr(VI) adsorption due to the competition of Cl(-) in the aqueous solutions. The batch equilibrium data were correlated to Langmuir and Freundlich isotherms and the data fitted better to the Freundlich isotherm equation. The apparent thermodynamic parameters were calculated for each of the four biosorbents and the obtained numerical values showed that the Cr(VI) adsorption onto the various low-cost biosorbents is spontaneous, entropy-driven and endothermic processes. The batch kinetic data were correlated to the pseudo-first order and pseudo-second order models and the data fitted better to the pseudo-second order equation. An intraparticle diffusion model was applied to investigate the adsorption mechanisms. The adsorption capacities for various biosorbents studied in this work were inversely proportional to the adsorbent concentrations.     

Chromium(VI) adsorption from aqueous solution by Hevea Brasilinesis sawdust activated carbon

Adsorption capacity of Cr(VI) onto Hevea Brasilinesis (Rubber wood) sawdust activated carbon was investigated in a batch system by considering the effects of various parameters like contact time, initial concentration, pH and temperature. Cr(VI) removal is pH dependent and found to be maximum at pH 2.0. Increases in adsorption capacity with increase in temperature indicate that the adsorption reaction is endothermic. Based on this study, the thermodynamic parameters like standard Gibb's free energy (DeltaG degrees ), standard enthalpy (DeltaH degrees ) and standard entropy (DeltaS degrees ) were evaluated. Adsorption kinetics of Cr(VI) ions onto rubber wood sawdust activated carbon were analyzed by pseudo first-order and pseudo second-order models. Pseudo second-order model was found to explain the kinetics of Cr(VI) adsorption most effectively. Intraparticle diffusion studies at different temperatures show that the mechanism of adsorption is mainly dependent on diffusion. The rate of intraparticle diffusion, film diffusion coefficient and pore diffusion coefficient at various temperatures were evaluated. The Langmuir, Freundlich and Temkin isotherm were used to describe the adsorption equilibrium studies of rubber wood sawdust activated carbon at different temperatures. Langmuir isotherm shows better fit than Freundlich and Temkin isotherm in the temperature range studied. The result shows that the rubber wood sawdust activated carbon can be efficiently used for the treatment of wastewaters containing chromium as a low cost alternative compared to commercial activated carbon and other adsorbents reported.