PVC/TPU/NBR三元共混物的制备及性能研究

对PVC／热塑性聚氨酯（TPU）／SR三元共混物的性能进行研究，重点讨论NBR品种、TPU／NBR并用比、PVC聚合度、增塑剂DOP和硫化剂DCP用量对PVC／TPU／NBR三元共混物性能的影响。结果表明。PVC／TPU／NBR-3604三元共混物的物理性能较优；PVC／TPU／NBR-3604三元共混物的拉断伸长率和拉断永久变形均随着PVC聚合度的增大基本呈上升趋势；随着增塑剂DOP用量的增大，共混物的邵尔A型硬度、拉伸强度、撕裂强度和拉断永久变形均基本呈下降趋势，拉断伸长率增大；随着硫化剂DCP用量的增大。共混物的拉伸强度和拉断伸长率变化不大，撕裂强度基本呈逐渐减小的趋势。不同PVC／TPU／SR三元共混物的扫描电子显微镜照片表明，NBR与PVC和TPU的相容性较好。     

Compatibilized blends of PVC/PA12 and PVC/PP containing poly(lauryl lactam‐block‐caprolactone)

Specially designed block copolymers have played a role as compatibilizing agents in the system of immiscible polymer blends. We applied lauryl lactam (LA)–caprolactone (CL) block copolymer [P(LA‐b‐CL)] as a compatibilizing agent for immiscible poly(vinyl chloride) (PVC) blends with various polymers. These blends possess high thermal performance and toughness. We investigated the effect of P(LA‐b‐CL) as a compatibilizing agent for immiscible PVC blends with poly(ω‐lauryl lactam) [polyamide 12 (PA12)]. We also described the invention of a new compatibilizing agent system involving P(LA‐b‐CL) for PVC/polypropylene (PP) blends. The mechanical and thermal properties of (1) PVC/PA12 blend compatibilized with P(LA‐b‐CL) and (2) PVC/PP blend compatibilized with P(LA‐b‐CL)/PA12/maleic anhydride–modified PP were both enhanced. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1983‐1992, 2004     

Scrutinizing the influence of peroxide crosslinking of dynamically vulcanized EVA/TPU blends with special reference to cable sheathing applications

A novel thermoplastic vulcanizate (TPV) based on the blends of ethylene vinyl acetate/thermoplastic polyurethane (EVA/TPU) at various blend ratios has been developed via dynamic vulcanization at 180 °C using di‐(2‐tert‐butyl peroxy isopropyl) benzene (DTBPIB) peroxide as the cross‐linking agent. Modification of the EVA/TPU blends via dynamic crosslinking significantly improves the tensile strength and modulus of the system and the improvement is more significant for EVA/TPU 50/50 and 60/40 blends. AFM study shows that crosslinked EVA particles are dispersed in the continuous TPU matrix and the dispersed EVA domain sizes are relatively smaller in EVA/TPU 50/50 and 60/40 blends leading to good mechanical properties. FTIR spectroscopy has been used to characterize the specific chemical changes occurring due to dynamic vulcanization. This TPV has excellent retention of physico‐mechanical properties even after reprocessing twice and the blends also have very good thermal resistance as indicated by aging study. The samples were found to exhibit remarkable improvement in oil resistance property as compared to their uncrosslinked counterpart. The creep behavior of the blends significantly improves after dynamic crosslinking and blends with higher TPU content show better creep resistance. Volume resistivity of all the peroxide vulcanized blends is in the range of 10¹³ ohm cm, which is suitable for cable sheathing application. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43706.     

Morphology and properties of blends with different thermoplastic polyurethanes and polyolefines

Unmodified blends of two thermoplastic polyurethanes (TPU) and six polyolefines were used to study the influence of the component viscosities on the blend morphology and mechanical properties. Blends were produced by melt mixing using a twin screw extruder. Interactions between the blend components could not be detected by DSC, DMA, selective extraction, and SEM micrographs of cryofractures. The variation in tensile strength with blend composition produce a U-shaped curve with the minimum between 40 and 60 wt % of polyolefine. At similar viscosity ratios (η_d/η_m), blends with polyether based TPU (TPU-eth) have a finer morphology than blends with polyester based TPU (TPU-est). This is due to the lower surface free energy of the polyether soft segments compared to the polyester soft segments. Different morphologies also lead to changes in mechanical behavior. Blends with TPU-eth show a lower decrease in tensile strength with blend composition than blends with TPU-est. The viscosity ratio between TPU and polyolefines can be directly correlated to the blend morphology obtained under similar blending conditions. TPU/PE blends show a lower dispersity than TPU/PP blends, due to the higher viscosity ratios of TPU/PE blends. This results in a greater reduction in tensile strength with the disperse phase content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 749–762, 1997     

Crosslinking of polyvinyl chloride by electron beam irradiation in the presence of ethylene–vinyl acetate copolymer

Electron beam (EB) irradiation of polyvinyl chloride (PVC) was carried out in the presence of three different ethylene–vinyl acetate copolymers (EVA). The mechanical properties of the original and irradiated blends were tested. The gel content measurement, chlorine loss upon electron irradiation, and gel permeation chromatograph (GPC) were used to characterize the effect of EVA on the irradiation behavior of PVC/EVA blends. The content and the chemical structure of EVA in the blends had considerable effects on the mechanical properties and gel content of the blends. The incorporation of EVA into PVC blend can increase the gel content and reduce chlorine loss of the blends. The GPC analysis of the soluble part in the irradiated PVC samples showed that the addition of EVA into the PVC blend lowered the polydispersity of molecular weight of PVC. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1571–1575, 2004     

Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

热塑性聚氨酯与聚氯乙烯共混改性研究

采用机械共混法制备了热塑性聚氨酯(TPU)与聚氯乙烯(PVC)共混物。探讨了共混比对TPU／PVC共混物性能的影响，优化出TPU／PVC共混比30／70(质量比)，在此基础上研究了增塑剂、热稳定剂、填料对TPU／PVC共混物力学性能、流变性能和耐油、耐溶剂性能的影响。研究结果表明，TPU／PVC共混物的力学性能在共混时有协同作用，耐油、耐溶剂性均较好，从成本和实用两方面出发，选择TPU／PVC=30／70共混比更有实用性。随增塑剂DOP的增加，共混物的力学性能呈下降趋势。在所选热稳定剂中，以硬脂酸钙制得共混物的力学性能最好；在所选填料中，白炭黑的补强效果最好。扫描电镜观察共混物的微观结构显示，TPU／PVC共混比为30／70有较好的相容性，这与力学性能结果相一致。TGA分析显示，TPU的加入提高了共混物的热稳定性。红外光谱分析表明，TPU和PVC共混只是一个简单的物理共混过程。     

Mechanical properties and morphology of PP/ABS blends compatibilized with PP‐g‐2‐HEMA

Polypropylene (PP) and acrylonitrile–butadiene–styrene blends of different composition were prepared using a single‐screw extruder. The binary blend of PP/ABS was observed to be incompatible and shows poor mechanical properties. PP‐g‐2‐hydroxyethyl methacrylate (2‐HEMA) was used as a compatibilizer for the PP/ABS blends. The ternary compatibilized blends of PP/ABS/PP‐g‐2‐HEMA showed improvement in the mechanical properties. Electron micrographs of these blends showed a homogeneous and finer distribution of the dispersed phase. The mechanical performance increased particularly in the PP‐rich blend. The 2.5‐phr (part per hundred of resin) compatibilizer was observed to bring improvement to the properties. The suitability of various existing theoretical models for the predication of the tensile moduli of these blends was examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 72–78, 2003     

PVC／TPU／SBS—g—MMA共混体系研究

制备了ＳＢＳ－ｇ－ＭＭＡ系列接枝共聚物,并对其进行了表征。以ＳＢＳ－ｇ－ＭＭＡ作为ＰＶＣ／ＴＰＵ共混体系的增容剂,对不同配比的ＰＶＣ／ＴＰＵ／ＳＢＳ－ｇ－ＭＭＡ共混体系的物理力学性能、流变性等进行了研究。结果表明,ＳＢＳ－ｇ－ＭＭＡ接枝共聚物对ＰＶＣ／ＴＰＵ共混体系起到了明显的增容作用。     

Studies on polymer blends with moderate specific interactions. 2. phase structure of blends SAN/TPU and SAN/TPU/EVA

This paper deals with morphological studies of binary and ternary blends composed of poly(styrene-co-acrylonitrile) (SAN), polyurethane elastomer (TPU) and poly(ethylene-co-vinyl acetate) (EVA). Selective etching was found necessary to expose the morphologies of the blends. Chloroform or hot acetone, hexane/toluene (2/1v/v) and NaOH/CH₃OH (1wt%) were found to be selective etching agents for SAN, EVA and TPU, respectively. SAN and TPU form blends with fine dispersion structure, while SAN and EVA lead to rough phase structure with poor phase adhesion. These results are in accordance with the difference in the mechanical properties of SAN/TPU and SAN/EVA. In addition, for SAN/TPU/EVA blends, if TPU is only a minor component, it is preferentially located at the interphase, playing the role of a compatibilizer. As the amount of TPU increases, the compatibility is gradually improved. ©1997 SCI     

Effect of the elastomer type on the microstructure and mechanical properties of polypropylene

In this study, the effects of the elastomer type—ethylene–propylene–diene monomer (EPDM), three kinds of ethylene vinyl acetate (EVA 9, EVA 18, and EVA 28, where the number is the vinyl acetate concentration), and styrene–butadiene–styrene—and content on the microstructure and mechanical and thermal properties of isotactic polypropylene (i‐PP) blends were investigated. Five different elastomer concentrations (3, 6, 9, 12, and 15 wt %) were added to i‐PP to produce polypropylene/elastomer blends. The yield and tensile strengths, elastic modulus, impact strength, hardness, melt flow index (MFI), and structural properties of the blends were investigated. The tensile and yield strengths, elastic modulus, and hardness decreased gradually, whereas the impact strength and MFI increased as the elastomer content increased. As a result, with respect to the impact strength, the most effective elastomers were EPDM with 15 wt % and EVA 28 with 15 wt % for higher impact strength values. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1445–1450, 2005     

i-PP/HDPE blends. III. Characterization and compatibilization at lower i-PP contents

The mechanical properties of high-density polyethylene (HDPE)-rich i-PP/HDPE blends were studied. Two grades of HDPE were investigated, one with a melt viscosity close to that of the polypropylene (PP) and the other having a much lower melt viscosity. Compatibilization of the 10/90 i-PP/HDPE blend with three copolymers (an ethylene/propylene/diene [EPDM] copolymer and two ethylene/vinylacetate [EVA] copolymers, differing in their VA content) was also investigated. Blends of PP with the low melt viscosity HDPE displayed poor mechanical properties. It was not possible to improve these properties sufficiently with EPDM or EVA. In the case where viscosity matching was achieved between PP and HDPE, addition of i-PP (up to 30%) to HDPE resulted in a large drop in the impact strength of the blends, compared to that of the neat HDPE. A large drop (>50%) was also observed in the ultimate tensile elongation. However, the flexural modulus, yield stress, and ultimate tensile strength all increased with the introduction of i-PP into HDPE. Modification of these blends with an EPDM resulted in the return of all properties to values very close to those of the neat HDPE. The ultimate tensile elongation of the EPDM-modified i-PP/HDPE blend even exceeded that of the virgin HDPE. It was also found that although EVAs can be used to compatibilize these blends these additives were not as effective as was the EPDM. © 1996 John Wiley & Sons, Inc.     

Plastification of poly(vinyl chloride) by polymer blending

Blends of poly(vinyl chloride) (PVC) with different copolymers have been studied to obtain a plasticized PVC with improved properties and the absence of plasticizer migration. The copolymers used as plasticizers in the blends were acrylonitrile butadiene rubber, ethylene vinyl acetate (EVA), and ethylene-acrylic copolymer (E-Acry). Blends were studied with regard to their processing, miscibility, and mechanical properties, as a function of blend and copolymer composition. The results obtained were compared with those of equivalent compositions in the PVC/dioctyl phthalate (DOP) system. Better results than PVC/DOP were obtained for PVC/acrylonitrile butadiene rubber blends. The plasticizing effect on PVC of EVA and E-Acry copolymers was similar to that of DOP. It is shown that crosslinking PVC/E-Acry blends or increasing the vinyl acetate content in PVC/EVA blends, are alternatives that can increase the compatibility and mechanical properties of these blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1303–1312, 2000     

PVC抗静电材料的研究

选用导电炭黑及热塑性聚氨酯弹性体(TPU)、丁腈橡胶(P83)等改性剂对聚氯乙烯(PVC)进行抗静电及增韧研究,测试及分析了PVC共混体系的电性能、机械性能及耐热性能。实验结果表明:添加一定量的导电炭黑能明显提高材料的抗静电性能,但其冲击性能也随导电炭黑加入量的增加而下降,通过加入改性剂可改善体系的韧性。PVC/炭黑/TPU体系具有较高的抗静电效果及综合性能。     

Properties of uncompatibilized and compatibilized poly(butylene terephthalate)–LLDPE blends

In this work, blends of poly(butylene terephthalate) (PBT) and linear low‐density polyethylene (LLDPE) were prepared. LLDPE was used as an impact modifier. Since the system was found to be incompatible, compatibilization was sought for by the addition of the following two types of functionalized polyethylene: ethylene vinylacetate copolymer (EVA) and maleic anhydride‐grafted EVA copolymer (EVA‐g‐MAH). The effects of the compatibilizers on the rheological and mechanical properties of the blends have been also quantitatively investigated. The impact strength of the PBT–LLDPE binary blends slightly increased at a lower concentration of LLDPE but increased remarkably above a concentration of 60 wt % of LLDPE. The morphology of the blends showed that the LLDPE particles had dispersed in the PBT matrix below 40 wt % of LLDPE, while, at 60 wt % of LLDPE, a co‐continuous morphology was obtained, which could explain the increase of the impact strength of the blend. Generally, the mechanical strength was decreased by adding LLDPE to PBT. Addition of EVA or EVA‐g‐MAH as a compatibilizer to PBT–LLDPE (70/30) blend considerably improved the impact strength of the blend without significantly sacrificing the tensile and the flexural strength. More improvement in those mechanical properties was observed in the case of the EVA‐g‐MAH system than for the EVA system. A larger viscosity increase was also observed in the case of the EVA‐g‐MAH than EVA. This may be due to interaction of the EVA‐g‐MAH with PBT. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 989–997, 1999     

Effect of flexibility of ethylene vinyl acetate and crystallization of polypropylene on the mechanical properties of i‐PP/EVA blends

Polymer blend technology has been widely used for the past several years for the modification or enhancement of mechanical properties of polymers to obtain an overall balance of properties over those of the constituents. Despite its interesting mechanical and thermal properties, the impact strength of polypropylene leaves wide scope for improvement. A series of blends of ethylene vinyl acetate (EVA) copolymer with an impact grade of isotactic polypropylene (i‐PP) were prepared by single screw extrusion at 0–0.32 volume fraction of the dispersed phase. The mechanical properties such as tensile behavior, elongation‐at‐break, and impact strength of these blends systems as well as crystallinity were evaluated. Crystallinity data have been used in greater depth to support the mechanical properties. Differential scanning calorimetry studies conducted to study the modification in crystallinity of the crystalline component, i‐PP, of the blend revealed that the rubber component of the blend enhanced the crystallinity of i‐PP phase by providing sites for nucleation. Tensile modulus and strength decreased while the impact strength and breaking elongation enhanced with blending elastomer concentration. The improved properties of these PP/EVA blends are encouraging for carrying out further work on this system (composites) and suggest potential high impact strength applications for PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of nanoclay‐filled polyurethane/polypropylene blends

Ester‐based thermoplastic polyurethane (TPU) nanocomposites were prepared by melt blending at 190°C, using 3 wt% Cloisite 10A (organically modified montmorillonite clay) as the nanoscale reinforcement [TPU(C10A)]. The nanocomposites were subsequently melt‐blended with polypropylene (PP) using maleic anhydride–grafted polypropylene (MA‐g‐PP) as a compatibilizer [in the ratio of 70/30‐TPU/PP, 70/25/5‐TPU/PP/MA‐g‐PP, 70/25/5‐TPU (C10A)/PP/MA‐g‐PP]. Besides giving substantial increase in modulus, tensile strength, and other properties, organoclay reinforcement functions as a surface modifier for TPU hard segment resulting in improved dispersion. The morphology and other characteristics of the nanocomposite blends were investigated in terms of X‐ray diffraction, fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, tensile properties, scanning electron microscopy, and atomic force microscopy. The results indicate that the ester‐TPU(C10A)/PP/MA‐g‐PP exhibited better dispersion than other blend systems; abrasion resistance and water absorption resistance were also better for this system. POLYM. ENG. SCI., 50:1878–1886, 2010. © 2010 Society of Plastics Engineers     

Studies on preparation of immersion‐type polypropylene fragrant fiber. I. Formation of matrix fiber in the melt‐spinning process and its technique of immersion essential oil

Polypropylene/ethylene vinyl acetate (PP/EVA) blends were prepared in a plastic extruder with a static mixer. The thermodynamic compatibility, morphology, crystal form, and rheological behavior of PP/EVA blends were investigated by SEM, DSC, and rheology instruments. The results showed that PP and EVA were thermodynamically incompatible, the viscosity of the PP/EVA blends decreased with increase of shear rate in a range of temperature, the PP/EVA blends had a sea‐islands structure, and the crystalline zones remained in their original state and could not form mixed crystals in the PP/EVA blends. The PP/EVA blends were melt spun to prepare matrix fibers and the spinning conditions such as EVA content, the matching factor between pump delivery and winding velocity, and the melt‐spinning temperature were also determined. The sorption process of a matrix fiber for essential oils, adsorbed under various sorption conditions such as sorption time, sorption temperature, and EVA content, was also studied. The results revealed that the composite isotherm of the adsorption of matrix fiber for essential oil was characteristic of a U model. Through adsorbing essential oil, the immersion‐type PP fragrant fibers could be prepared with the matrix fiber. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1970–1979, 2003     

Constructing the core–shell structured island domain in polymer blends to achieve high dielectric constant and low loss

Carbon nanotubes (CNTs) and barium titanate (BaTiO₃) (BT) were simultaneously introduced into the immiscible blend poly(ethylene‐co‐vinyl acetate)/thermoplastic urethane (EVA/TPU), and the EVA/TPU/CNT/BT quaternary polymer composite blends with core–shell structured island TPU domain were successfully prepared, in which CNTs in the TPU domain act as the core and the BT spheres at the interface of the TPU and EVA act as the shell. A core–shell structured island can lead to the formation of micro‐capacitors and further accumulate electron storage owing to the incorporation of CNTs and BT; on the other hand, a BT shell can be assembled along the TPU spheres, reducing the possibility of formation of a conductive CNT network, resulting in suppressed dielectric loss. Therefore, CNTs and BT were tailor‐made into blend composites with a core–shell structured domain, which can achieve an increased dielectric constant by 176% and decreased low dielectric loss by 80% compared with the blend composites with only CNTs in the TPU domain. © 2019 Society of Chemical Industry     

氯化聚丙烯对PP/PVC共混物性能的影响

以氯化聚丙烯(CPP)为增容剂,探讨了CPP不同含量下PP/PVC体系的力学性能、相容性、流变性能以及对应的微观结构,并与氯化聚乙烯(CPE)增容剂进行了比较。发现添加5份CPP可明显改善PP和PVC两相界面相容性,与PP/PVC体系相比,拉伸强度提高了61%,无缺口冲击强度提高了100%。此时CPP还起到了一定的增塑作用,共混体系加工性能较好。与CPE相比,含有CPP的共混体系拉伸强度较高。