Prepolymerization of ethylene with a Ziegler–Natta catalyst

The slurry prepolymerization of ethylene using TiCl₄/MgCl₂ as a catalyst was investigated. A 2³‐factorial experimental design method was employed to study the effects of the temperature, hydrogen, and active cocatalyst‐to‐catalyst molar ratio (Al/Ti) on the catalyst activity, prepolymer melt flow index, and powder bulk density. All dependent variables increased when the active Al/Ti ratio increased from 1 to 2. The hydrogen–Al/Ti interaction had a significant effect on the prepolymer melt flow index and catalyst activity. The hydrogen (partial pressure ranging from 0.5 to 1.5 bar) and temperature (ranging from 60 to 80°C) variables as well as the hydrogen–temperature and hydrogen–temperature–Al/Ti interactions increased the prepolymer powder bulk density, which ranged from 0.11 to 0.373 g/cc. To find the reason for the prepolymer powder bulk density variation with the operating conditions, the particle size distribution and crystallinity of the prepolymers were determined. The increasing catalyst activity, ranging from 132 to 660 g of polyethylene/mmol of Ti, enhanced the weight percentage of fines, which ranged from 3 to 60, and decreased the average particle size, which ranged from 562 to 120 μm. This was the reason for the increasing prepolymer powder bulk density and could be due to the breakup of the prepolymer particles during prepolymerization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Nature of activating effect of two‐step polymerization of propylene

The prepolymerization effect on propylene polymerization in the presence of a TiCl₃‐based catalyst, modified by di‐n‐buthyl ether, was studied. The influence of prepolymerization on the electron spin resonance spectra and morphology of the catalyst, as well as the properties and the morphology of both prepolymer and regular polymerization products, was investigated. The polymer morphology was evaluated through scanning electron microscopy, polymer bulk density, and particle size distribution. Some evidence of the enhancement effect of prepolymerization on the catalyst activity and stereospecificity was obtained. No influence from prepolymerization was observed on molecular weight and its distribution, melting point, and crystallinity of polypropylene. These findings, when discussed in connection with the morphology results of the catalyst and prepolymer, showed that the prepolymerization performed at mild reaction conditions prevents fast and extensive “fragmentation” of the original catalyst agglomerates. The more controlled breakup of the catalyst particles in the course of slowed growth of prepolymer exposes the occluded catalyst fragments with uniform size and prevents their reagglomeration. Resulting from the above, catalyst homogeneity, catalyst activity, and polymer morphology are improved. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 353–359, 1999     

Polymerization of olefins through heterogeneous catalysis. IX. Experimental study of propylene polymerization over a high activity MgCl2-supported Ti catalyst

Results from an experimental study of propylene polymerization in heptane diluent over a high activity Mg-supported Ti catalyst are presented. The study provides an examination of the effect of operating conditions on polymerization rate, product melt index, and powder bulk density. Among the findings are that product bulk density decreases with increasing operating temperature and decreasing operating pressure while prepolymerization increases the bulk density. The results support the hypothesis that polymer morphology is closely linked to mass transfer limitations within the growing polymer particle during the early stages of polymerization.     

Preparation of ultra‐high‐molecular‐weight polyethylene and its morphological study with a heterogeneous Ziegler–Natta catalyst

Ultra‐high‐molecular‐weight polyethylene (PE) with viscosity‐average molecular weight (M_v) of 3.1 × 10⁶ to 5.2 × 10⁶ was prepared with a heterogeneous Ziegler–Natta MgCl₂ (ethoxide type)/TiCl₄/triethylaluminum catalyst system under controlled conditions. The optimum activity of the catalyst was obtained at a [Al]/[Ti] molar ratio of 61 : 1 and a polymerization temperature of 60°C, whereas the activity of the catalyst increased with monomer pressure and decreased with hydrogen concentration. The titanium content of the catalyst was 2.4 wt %. The rate/time profile of the catalyst was a decay type with a short acceleration period. M_v of the PE obtained decreased with increasing hydrogen concentration and polymerization temperature. The effect of stirrer speeds from 100 to 400 rpm did not so much affect the catalyst activity; however, dramatic effects were observed on the morphology of the polymer particles obtained. A stirrer speed of 200 rpm produced PE with a uniform globulelike morphological growth on the polymer particles. The particle size distributions of the polymer samples were determined and were between 14 and 67 μm. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Kinetics of the propylene polymerization with prepolymerization at high temperature using Ziegler‐Natta catalyst

The bulk polymerization of propylene in liquid monomers with Ziegler‐Natta catalyst at 95°C is studied, using alkyl aluminum as the cocatalyst and dicyclopentyldimethoxysilane as the external donor. The highest catalyst activity is shown at the cocatalyst/Ti molar ratio of 300, which keeps relatively constant with the molar ratio increasing from 300 to 800. Besides, the catalyst activity is up to 65 kgPP/(gCat*h) in the range of cocatalyst/donor molar ratio from 12 to 16. The polymerization reaction rate curves with and without catalyst precontacting are similar, while the activity with catalyst precontacting are higher than that without precontacting. Furthermore, the kinetics of polymerization with and without prepolymerization are investigated in the range of the polymerization temperature from 70 to 95°C. It shows that at the high temperature, the polymerization rate increases with prepolymerization. Finally, the influence of prepolymerization at 95°C on the polymerization kinetics and particle properties is also described. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41816.     

Investigations of the initial state polymerization of propylene with Ziegler–Natta catalysts in slurry

The initial state polymerization of propylene with Ziegler–Natta catalysts has been investigated and discussed at very low polymerization yields under adiabatic industrial prepolymerization conditions in diluted slurry regarding the effects of significant process parameters like monomer pressure, aluminum alkyl, and donor kind and concentration including the morphology of the catalyst/polymer particles formed. A sharp temperature increase in the first minutes of the initial state polymerization is followed by a temperature maximum and a slow decrease. With cocatalyst triethyl aluminum (TEAL), high prepolymerization yields were already achieved at a molar ratio TEAL/Ti of 3.0, remaining about constant until ratios of at least 300. The external donor dicyclopentyl dimethoxy silane leads to higher polymerization yields than the donor cyclohexyl dimethoxymethyl silane in the initial state polymerization too; however, both show a remarkable decreasing effect on polymerization yield above a specific molar ratio donor/Ti obviously correlated with the bulkiness of the alkyl groups. The particle size of the catalyst and the catalyst/prepolymer particles is increasing with polymerization yield until about 22 g PP/g Cat with particles almost perfectly spherical. The particle size distribution is rather broad at lower prepolymerization stages but unifying with lower polymerization rates at higher polymerization times. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Millimeter‐size polyethylene hollow spheres synthesized with MgCl2‐supported Ziegler‐Natta catalyst

Polyethylene hollow spheres with diameters of 0.4–2 mm were synthesized by a two‐step slurry polymerization in a single reactor with a spherical MgCl₂‐supported Ziegler‐Natta catalyst activated by triethylaluminum, in which the first step was prepolymerization with 0.1 MPa propylene and the second step was ethylene polymerization under 0.6 MPa. The prepolymerization step was found necessary for the formation of hollow spherical particles with regular shape (perfectly spherical shape). The effects of adding small amount of propylene (propylene/ethylene < 0.1 mol/mol) in the reactor after the prepolymerization step were investigated. Average size of the polymer particles was increased, and the polymerization rate was markedly enhanced by the added propylene. Development of the particle morphology with polymerization time was also studied. The polymer particles formed by less than 20 min of ethylene polymerization showed hollow spherical morphology with thin shell layer. Most of the particles had ratio of shell thickness/particle radius smaller than 0.5. By prolonging the ethylene polymerization, the shell thickness/particle radius ratio gradually approached 1, and the central void tended to disappear. Central void in polymer particles formed from smaller catalyst particles disappeared after shorter time of polymerization than those formed from bigger catalyst particles. The shell layer of the hollow particles contained large number of macro‐, meso‐ and micro‐pores. The mesopore size distributions of four typical samples were analyzed by nitrogen adsorption–desorption experiments. A simplified multigrain model was proposed to explain the morphogenesis of the hollow spherical particles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43207.     

Particle control of Ziegler–Natta catalysts based on TiCl3 for propylene polymerization. Effect of prepolymerization

Prepolymerizations employing an extremely high stereospecific and high active catalyst based on TiCl₃ modified by di-n-butyl ether (DBE) were carried out with different monomers (styrene, propylene, hexene-1, cyclopentadiene). The influence of prepolymerization on the morphology of polypropylene obtained with TiCl₃ catalyst was investigated. The catalyst was synthesized by TiCl₄ reduction in toluene solution with A1Et₃·DBE complex. The polymer morphology was evaluated through optical and scanning electron microscopies and polymer bulk density and particle size distribution. © 1994 John Wiley & Sons, Inc.     

Morphological study of spherical MgCl2.nEtOH supported TiCl4 Ziegler‐Natta catalyst for polymerization of ethylene

Spherical MgCl₂·nEtOH was prepared by adducting ethanol to MgCl₂ using melt quenching method. Effect of molar ratio of [EtOH]/[MgCl₂] = 2.8–3.05 on the morphology and particle size of the MgCl₂·nEtOH were studied. The best adduct of spherical morphology was obtained when 2.9 mol ethanol to 1 mol MgCl₂ was used. An emulsion of dissolved MgCl₂ in ethanol was prepared in a reactor containing silicon oil. Stirrer speed of the emulsion and its transfer rate to quenching section that work at ?10 to ?40°C are affected by the particle size of the adduct particle. The adducted ethanol was partially removed with controlled heat primary to catalyst preparation (support). Treatment of the support with excess TiCl₄ increased its surface area from 13.1 to 184.4 m²/g. Heterogeneous Ziegler‐Natta catalyst system of MgCl₂ (spherical)/TiCl₄ was prepared using the spherical support. Scanning electron microscopy studies of adduct, support, and catalyst obtained shown spherical particles, however, the polyethylene particles obtained have no regular morphology. The behavior indicates harsh conditions used for catalyst preparation, prepolymerization, and polymerization method used. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3829–3834, 2006     

Late Transition Metal Catalyst Based on Cobalt for Polymerization of Ethylene

The late transition metal catalyst of [2,6-diacethylpyridinebis(2,6-diisopropylphenylimine)]cobalt(II) dichloride was prepared under controlled conditions and used for polymerization of ethylene. Methylaluminoxane (MAO) and triisobuthylaluminum (TIBA) were used as a cocatalyst and a scavenger, respectively. The highest activity of the catalyst was obtained at about 30°C; the activity decreased with increasing temperature. At polymerization temperatures higher than 50°C not only was a sharp decrease in the activity observed but also low molecular weight polyethylene product that was oily in appearance was obtained. The polymerization activity increased with increasing both of the monomer pressure and [MAO]:[Co] ratio. However, fouling of the reactor was strongly increased with increasing both of the monomer pressure and the amount of MAO used for the homogeneous polymerization. Hydrogen was used as the chain transfer. The activity of the catalyst and the viscosity average molecular weight (M_v) of the polymer obtained were not sensitive to hydrogen concentration. However, the viscosity average molecular weight of the polymer decreased with the monomer pressure. The (M_v), the melting point, and the crystallinity of the resulting polymer at the monomer pressure of 1 bar and polymerization temperature of 20°C were 1.2 × 10⁵, 133°C, and 67%, respectively. Heterogeneous polymerization of ethylene using the catalyst and the MAO/SiO₂ improved morphology of the resulting polymer; however, the activity of the catalyst was also decreased. Fouling of the reactor was eliminated using the supported catalyst system.     

Copolymerization of ethylene/α‐olefins using bis(2‐phenylindenyl)zirconium dichloride metallocene catalyst: structural study of comonomer distribution

Catalysts have a major role in the polymerization of olefins and exert their influence in three ways: (1) polymerization behaviour, including polymerization activity and kinetics; (2) polymer particle morphology, including bulk density, particle size, particle size distribution and particle shape; and (3) polymer microstructure, including molecular weight regulation, chemical composition distribution and short‐ and long‐chain branching. By tailoring the catalyst structure, such as the creation of a bridge or introducing a substituent on the ligand, metallocene catalysts can play a major role in the achievement of desirable properties. Kinetic profiles of the metallocene catalyst used in this study showed decay‐type behaviour for copolymerization of ethylene/α‐olefins. It was observed that increasing the comonomer ratio in the feedstock affected physical properties such as reducing the melting temperature, crystallinity, density and molecular weight of the copolymers. It was also observed that the heterogeneity of the chemical composition distribution and the physical properties were enhanced as the comonomer molecular weight was increased. In particular, 2‐phenyl substitution on the indenyl ring reduced somewhat the melting point of the copolymers. In addition, the copolymer produced using bis(2‐phenylindenyl)zirconium dichloride (bis(2‐PhInd)ZrCl₂) catalyst exhibited a narrower distribution of lamellae (0.3–0.9 nm) than the polymer produced using bisindenylzirconium dichloride catalyst (0.5–3.6 nm). The results obtained indicate that the bis(2‐PhInd)ZrCl₂ catalyst showed a good comonomer incorporation ability. The heterogeneity of the chemical composition distribution and the physical properties were influenced by the type of comonomer and type of substituent in the catalyst. Copyright © 2010 Society of Chemical Industry     

Polymerization of propylene using MgCl2 (ethoxide type)/TiCl4/diether heterogeneous Ziegler–Natta catalyst

Heterogeneous Ziegler–Natta catalyst of MgCl₂ (ethoxide type)/TiCl₄/diether was prepared. 2,2‐Diisobutyl‐1,3‐dimethoxy propane (DiBDMP), diether, was used as internal donor. Slurry polymerization of propylene was carried out using the catalyst in dry heptane while triethylaluminium (TEA) was used as co‐catalyst. The co‐catalyst effects, such as catalyst molar ratio, polymerization temperature, H₂ pressure, external donor, triisobutylaluminium (TiBA) and monomer pressure, on the activity of the catalyst and isotacticity index (II) of the polymers obtained were studied. Rate of polymerization versus polymerization time is of a decay type with no acceleration period. There are an optimum Al/Ti molar ratio and temperature to obtain the highest activity of the catalyst. The maximum activity was obtained at 60 °C. Increasing the monomer pressure to 1 010 000 Pa linearly increased the activity of the catalyst. Addition of hydrogen to 151 500 Pa pressure increased activity of the catalyst from 2.25 to 5.45 kg polypropylene (PP) (g cat)^?1 h^?1 using 505 000 Pa pressure of monomer. The II decreased with increasing Al/Ti ratio, monomer pressure, hydrogen pressure and increased with increasing temperature to 60 °C, following with decrease as the temperature increases. Productivity of 11.55 kg (PP) (g cat)^?1 h^?1 was obtained at 1 010 000 Pa pressure of monomer and temperature of 60 °C. Addition of methyl p‐toluate (MPT) and dimethoxymethyl cyclohexyl silane (DMMCHS) as external donors decreased the activity of the catalyst sharply, while the II slightly increased. Some studies of the catalyst structure and morphology of the polymer were carried out using FTIR, X‐ray fluorescence, scanning electron microscopy and Brunauer–Emmett–Teller techniques. Copyright © 2005 Society of Chemical Industry     

Propylene polymerization in slurry catalyzed by titanium trichloride–diethyl aluminum chloride

Propylene is polymerized in a slurry over a TiCl₃ · ?AlCl₃ catalyst with a DEAC cocatalyst, approaching conditions of industrial relevance. The effects of various parameters such as temperature, pressure, cocatalyst-to-catalyst ratio, hydrogen concentration, and polymerization time are investigated with particular emphasis on the yield, tacticity, molecular weight, bulk density, and particle size of the resulting polymer. The highest yield and isotactic content are obtained at an Al/Ti ratio of 6, temperature of 70°C, and pressure of 9 kg/cm²g. The polymerization rate is found to be first order up to a monomer concentration of 2.5 mol/L. The overall activation energy of polymerization calculated from an Arrhenius plot is found to be 11.6 kcal/mol. A correlation between MFI and molecular weight is also presented. © 1994 John Wiley & Sons, Inc.     

Emulsion polymerization of methyl methacrylate in concentration of emulsifiers below their CMCs—polymerization rate,particle size,and particle-size distribution

The emulsion polymerization of methyl methacrylate (MMA) in concentration of emulsifiers below their critical micelle concentrations (CMCs) initiated by K₂S₂O₈ (KPS) was studied. It was observed that the initiator concentration has little effect on both polymerization rate and particle size. However, the polymerization rate is faster and particle size is smaller obviously when decreasing the ratio of the water/monomer or increasing the temperature of polymerization or the amount of the emulsifier. In the range of a 200–400 rpm stirring speed, the polymerization rate is almost unchanged although the particle size become larger with increase in the stirring speed. The monodisperse particle (size about 100–200 nm) can be obtained using this process. The mechanism of emulsion polymerization of MMA in the emulsifier concentration below its CMC is discussed. © 1995 John Wiley & Sons, Inc.     

Butyl chloride as promoter in ethylene polymerization by magnesium ethoxide‐supported catalyst

The effects of butyl chloride as a promoter in the ethylene polymerization were studied using a Mg(OEt)₂/TiCl₄/triethyl aluminum (TEA) Ziegler–Natta catalyst system, where Mg(OEt)₂, TiCl₄, TEA were used as support, catalyst, and activator, respectively. The influence of BC on the catalyst performance, polymerization rate, and polymer properties were investigated. This study strongly indicates that BC could act as a promoter with high performance in the ethylene polymerization. There was a remarkable increase in the catalyst yield and polymerization rate, in particularly, in the presence of hydrogen which was used for controlling the molecular weight. A reduction in the polymer molecular weight was observed in the presence of BC and hydrogen. The morphology of the polymers was evaluated through scanning electron microscopy and particle size distribution. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40189.     

Preparation of porous spherical MgCl2/SiO2 complex support as precursor for catalytic propylene polymerization

The MgCl₂/SiO₂ complex support was prepared by spray drying using alcoholic suspension, which contained MgCl₂ and SiO₂. The complex support reacted with TiCl₄ and di‐n‐butyl phthalate, giving a catalyst for propylene polymerization. The catalyst was spherical and porous with high specific surface area. TEA was used as a cocatalyst, and four kinds of alkoxysilane were used as external donors. The bulk polymerization of propylene was studied with the catalyst system. The effect of the reaction conditions and external donor on the polymerization were investigated. The results showed that the catalyst had high activity, high stereospecificity, and sensitive hydrogen responsibility. Polypropylene has good grain morphology because of duplicating the morphology of the catalyst. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1296–1299, 2005     

新型高性能Ziegler-Natta催化剂用于乙烯淤浆聚合

A novel high performance MgCl2/TiCl4 catalyst with tetrabutyloxsilicane as electron donor was prepared for ethylene slurry polymerization process. The properties of the catalyst such as particle size distribution, catalytic activity, hydrogen responsibility and copolymerization performance were investigated and compared with commercial catalyst (imported catalyst). Copolymerization of ethylene and 1-butylene using the catalyst was stud-ied in a pilot plant. The composition, structure and property of the copolymer were characterized by 13C nuclear magnetic resonance (13C NMR) and gel permeation chromatography-Infrared (GPC-IR), and compared with those of the copolymer obtained from a commercial catalyst. In comparison with the commercial catalyst, the novel cata-lyst had a higher activity (up to 34.6 kg&#8226;g－1) and a better particle size distribution (PSD), and produced polymers having higher bulk density (up to 0.37 g&#8226;cm－3) with less fine resin. Meanwhile, the novel catalyst showed a higher hydrogen responsibility and better copolymerization performance. The results indicated that the copolymer obtained from the novel catalyst has a higher branch in the high molecular weight fraction and lower branch in the low mo-lecular weight fraction.     

氯乙烯本体预聚合动力学和成粒过程的研究

对氯乙烯(VC)本体预聚合动力学和成粒过程进行了研究。通过称重法测定了VC预聚合阶段的转化率,同时研究了搅拌转速、聚合温度和引发剂用量对聚合动力学的影响。采用LS-230Coulter激光粒度仪测定聚合过程PVC粒子的体均粒径及其分布,考察了搅拌转速、聚合温度和引发剂用量对临界转化率和临界粒径的影响。根据实验结果并结合低转化率下VC本体聚合的微观成粒机理,提出了VC本体预聚合的成粒过程。     

Copolymerization of ethylene–propylene using high‐activity bi‐supported Ziegler–Natta TiCl4 catalyst

Heterogeneous Ziegler–Natta TiCl₄ catalyst using MgCl₂ and SiO₂ as supports was prepared under controlled conditions. Mg(OEt)₂ was used as a starting material and was expected to convert to active MgCl₂ during catalyst preparation. Due to the high surface area and good morphological control, SiO₂ was chosen as well. Slurry copolymerization of ethylene and propylene (EPM) was carried out in dry n‐heptane by using the catalyst system SiO₂/MgCl₂/TiCl₄/EB/TiBA or TEA/MPT/H₂ at temperatures of 40–70°C, different molar ratios of alkyl aluminum : MPT : Ti, hydrogen concentrations, and relative and total monomers pressure. Titanium content of the catalyst was 2.96% and surface area of the catalyst was 78 m²/g. Triisobutyl aluminum (TiBA) and triethyl aluminum (TEA) were used as cocatalysts, while ethyl benzoate (EB) and methyl p‐toluate (MPT) were used as internal and external donors, respectively. H₂ was used as a chain‐transfer agent. Good‐quality ethylene propylene rubber (EPR) of rubber was obtained at the ratio of [TiBA] : [MPT] : [Ti] = 320 : 16 : 1 and polymerization temperature was 60°C. When TiBA was used as a cocatalyst, a higher and more rubberlike copolymer was obtained. For both of the cocatalysts, an optimum ratio of Al/Ti was obtained relative to the catalyst productivity. Ethylene content of the copolymer obtained increased with increasing TiBA concentration, while inverse results were obtained by using TEA. Addition of H₂ increased the reactivity of the catalyst. The highest product was obtained when 150 mL H₂/L solvent was used. Increasing temperature from 40 to 70°C decreased the productivity of the catalyst, while irregular behavior was observed on ethylene content. Relative pressure of P_P/P_E = 1.4 : 1 and total pressure of 1 atm was the best condition for the copolymerization. Polymers with ethylene contents of 25–84% were obtained. Increasing ethylene content of EPR decreased T_g of the polymer obtained to a limiting value. Viscosity‐average molecular weight (M_v) decreased with increasing temperature and TiBA and H₂ concentration. However, increasing the polymerization time increased the M_v. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2597–2605, 2004