Design and Analysis of Antipodal Vivaldi Antennas for Breast CancerDetection

This paper presents the design and analysis of antipodal Vivaldi antennas (AVAs) for breast cancer detection. In order to enhance the antenna gain, different techniques such as using the uniform and non-uniform corrugation, expanding the dielectric substrate and adding the parasitic patch are applied to original AVA. The design procedure of two developed AVA structures i.e., AVA with non-uniform corrugation and AVA with parasitic patch are presented. The proposed AVAs are designed on inexpensive FR4 substrate. The AVA with non-uniform corrugation has compact dimension of mm² or , where is wavelength of the lowest operating frequency. The antenna can operate within the frequency range from 1.63 GHz to over 8 GHz. For the AVA with parasitic patch and uniform corrugation, the overall size of antenna is mm² or It can operate within the frequency range from 1.4 GHz to over 8 GHz. The maximum gain for AVA with non-uniform corrugation and AVA with parasitic patch and uniform corrugation are 9.03 and 11.31 dBi, respectively. The corrugation profile and parasitic patch of the proposed antenna are optimized to achieve the desired properties for breast cancer detection. In addition, the proposed AVAs are measured with breast phantom to detect cancerous cell inside the breast and the performance in detecting cancerous cell are discussed. The measured result can confirm that the proposed AVAs can detect unwanted cell inside the breast while maintaining the compact size, simple structure and low complexity in design.     

Solution‐Processed Ti3C2Tx MXene Antennas for Radio‐Frequency Communication

Highly integrated, flexible, and ultrathin wireless communication components are in significant demand due to the explosive growth of portable and wearable electronic devices in the fifth‐generation (5G) network era, but only conventional metals meet the requirements for emerging radio‐frequency (RF) devices so far. Here, it is reported on Ti₃C₂T_x MXene microstrip transmission lines with low‐energy attenuation and patch antennas with high‐power radiation at frequencies from 5.6 to 16.4 GHz. The radiation efficiency of a 5.5 µm thick MXene patch antenna manufactured by spray‐coating from aqueous solution reaches 99% at 16.4 GHz, which is about the same as that of a standard 35 µm thick copper patch antenna at about 15% of its thickness and 7% of the copper weight. MXene outperforms all other materials evaluated for patch antennas to date. Moreover, it is demonstrated that an MXene patch antenna array with integrated feeding circuits on a conformal surface has comparable performance with that of a copper antenna array at 28 GHz, which is a target frequency in practical 5G applications. The versatility of MXene antennas in wide frequency ranges coupled with the flexibility, scalability, and ease of solution processing makes MXene promising for integrated RF components in various flexible electronic devices.     

Dual wideband coplanar waveguide-fed notched antennas with asymmetrical grounds for multi-band wireless application

A novel single-layer planar monopole antenna is proposed for dual wideband operation. The antenna is a notched patch fed by a coplanar waveguide with two asymmetrical ground planes. The parametrical effects of the size of two such grounds and an embedded notch on the impedance matching condition have been examined theoretically. By fabricating and measuring the prototypes of the proposed antenna, two bands with 10 dB return loss bandwidths of about 490 MHz centred at 2.13 GHz band and of about 99.2% ranging from 3.32 to 6.9 GHz were obtained. A stable radiation pattern and average gains of greater than 2.6 and 4.8 dBi, respectively, over the two operating bands have also been obtained. These properties make the antenna suitable for multi-frequency wireless operation.     

Wideband multilayered microstrip antennas fed by coplanar waveguide-loop with and without via combinations

Coplanar waveguide (CPW)-loop fed wideband multilayered microstrip antennas with and without via combinations are presented. The antenna consists of two dielectric substrates, CPW-loop on the ground plane layer, main patch on the middle layer and four asymmetric parasitic patches on the upper layer. The feed consists of a CPW, a loop on a ground plane and a via between main patch and feeding strip on the ground plane layer. Using via, the gain flatness over the impedance bandwidth and return loss are improved. The proposed antenna with four feeding structures is also studied. The 10 dB return loss bandwidths of the antenna with and without via are 34% (3.12? 4.41 GHz) and 33.7% (3.18 ?4.47 GHz), respectively. The measured gain is >5.0 dBi over the impedance bandwidth.     

Complementary split ring resonator metamaterial to achieve multifrequency operation in microstrip-based radiating structure design

Following recent findings on metamaterials, a miniaturized microstrip patch antenna loaded with a complementary split ring resonator (CSRR) was investigated for multiband operation. The proposed structure has a CSRR loaded in the base of the antenna to improve its performance and to make it a metamaterial. Metamaterials exhibit qualitatively new electromagnetic response functions that cannot be found in nature. The CSRR-loaded base allows simultaneous operation over several frequencies. Here, a total of seven bands were achieved by loading the patch antenna with the CSRR. The seven bands were centered around frequencies of 4.33 GHz, 5.29 GHz, 6.256 GHz, 7.066 GHz, 7.846 GHz, 8.86 GHz, and 9.75 GHz. Design results were obtained by using a high-frequency structure simulator that is used for simulating microwave passive components.     

A Compact Flexible Circularly Polarized Implantable Antenna forBiotelemetry Applications

With the help of in-body antennas, the wireless communication among the implantable medical devices (IMDs) and exterior monitoring equipment, the telemetry system has brought us many benefits. Thus, a very thin-profile circularly polarized (CP) in-body antenna, functioning in ISM band at 2.45 GHz, is proposed. A tapered coplanar waveguide (CPW) method is used to excite the antenna. The radiator contains a pentagonal shape with five horizontal slits inside to obtain a circular polarization behavior. A bendable Roger Duroid RT5880 material (ε_r = 2.2, tanδ = 0.0009) with a typical 0.25 mm-thickness is used as a substrate. The proposed antenna has a total volume of 21 × 13 × 0.25 mm³. The antenna covers up a bandwidth of 2.38 to 2.53 GHz (150 MHz) in vacuum, while in skin tissue it covers 1.56 to 2.72 GHz (1.16 GHz) and in the muscle tissue covers 2.16 to 3.17 GHz (1.01 GHz). GHz). The flexion analysis in the x and y axes was also performed in simulation as the proposed antenna works with a wider bandwidth in the skin and muscle tissue. The simulation and the curved antenna measurements turned out to be in good agreement. The impedance bandwidth of −10 dB and the axis ratio bandwidth of 3 dB (AR) are measured on the skin and imitative gel of the pig at 27.78% and 35.5%, 13.5% and 4.9%, respectively, at a frequency of 2.45 GHz. The simulations revealed that the specific absorption rate (SAR) in the skin is 0.634 and 0.914 W/kg in muscle on 1g-tissue. The recommended SAR values are below the limits set by the federal communications commission (FCC). Finally, the proposed low-profile implantable antenna has achieved very compact size, flexibility, lower SAR values, high gain, higher impedance and axis ratio bandwidths in the skin and muscle tissues of the human body. This antenna is smaller in size and a good applicant for application in medical implants.     

Virtual multiple input multiple output in multiple high-altitude platform constellations

Multiple-input multiple-output (MIMO) technology, which makes use of the spatial dimension by utilising multiple antennas at the transmitter and receiver, has proved an efficient solution for providing higher data throughput and/or link reliability in wireless systems. In this study, the authors investigate a virtual MIMO (V-MIMO) technique, based on a constellation of multiple high-altitude platforms (HAPs), providing broadband wireless access to high-speed trains under predominantly line-of-sight (LOS) propagation conditions. They analyse the performance of transmit diversity based on space?time block coding (STBC), in particular Alamouti and extended Alamouti schemes, using fixed wide-lobe receive antennas, and compare it to the reference receive diversity scheme based on best HAP selection that requires highly directional and steerable antennas. Simulation results for different diversity schemes are based on the calculation of carrier to interference-plus-noise ratio (CINR) along representative railway lines in a realistic terrain configuration. The CINR levels obtained are mapped onto transmission modes specified by standards developed for two wireless systems operating at distinct frequency bands, the DVB-S2 assumed for operation in mm-wave bands and the IEEE 802.16e (mobile WiMAX) for operation at 3.5 GHz. Simulation results show that the use of transmit diversity schemes in a multiple HAP constellation decreases the link outage and also increases the average spectral efficiency, but requires a marked increase in transmit power, especially for the system operating in mm-wave bands.     

Reflectenna: a quasi passive on?off keyed microwave telemetry system for remote sensor applications

A method to transmit one-directional wireless data with low power consumption has been investigated. This system, called the 'reflectenna', works on the principle of transmitting information by modulating an incident continuous wave carrier signal prior to re-transmission and consists of two orthogonally linear polarised, micromachined microstrip patch antennas and a single-pole-single-throw switch that modulates the carrier signal. This quasi-passive method to transmit data has been tested with a transceiver system that transmits a 10 GHz carrier signal and demodulates the received signal reflected back from the reflectenna. The carrier signal was modulated with a 2 kHz square wave and a link with a range up to 25 m was achieved.     

Some potential antenna applications of high-temperature superconductors

A review of possible applications of high-temperature superconductors (HTS) to antennas and antenna feed networks is presented. The frequency range of consideration is 1 MHz to 100 GHz. Three antenna application areas seem appropriate for HTS material. (1)Electrically small antennas and their matching networks: An increase in efficiency is possible for electrically short antennas, but at the expense of bandwidth. Substantial radiated power levels (on the order of kilowatts) can be handled by the best HTS material. Substantial improvement may be realized by making only the matching network of HTS material. (2)Feed and matching networks for compact arrays with enhanced directive gain (superdirective arrays): HTS material should permit such arrays to be fabricated that have high efficiency. (3)Feed networks for millimeter-wave arrays: Low-loss feed networks using HTS microstrip transmission lines give many decibels improvement in gain.     

Tunable mid-infrared patch antennas based on VO2 phase transition

The metal-insulator phase transition in vanadium oxide makes it an attractive material for developing reconfigurable infrared optoelectronic components. In this paper, we present a tunable mid-infrared plasmonic patch antenna array based on vanadium oxide. The antennas consist of a circular gold patch array separated from a metallic ground plane by a film of vanadium dioxide. As the insulator-to-metal phase transition is thermally triggered, the resonances of the antenna array redshift with reduced absorbance before they are eventually switched off. The measured tuning range is about 10% of the resonant frequency, and the modulation depth in reflection is as high as 50%. A hysteresis loop in the tuning behavior is also observed. The XRD and XPS characterizations reveal a polycrystalline and multi-phase vanadium oxide. Our demonstrated tunable patch antennas hold promise for optical switching and modulating in mid-infrared applications.     

具有滤波功能的蓝牙微带天线设计

为了有效抑制双倍频对2.4 GHz无线通信干扰,采用滤波馈电网络与天线振子一体设计技术,设计一种具有滤波功能的多层结构天线,使天线在2.4~2.5 GHz时,信号可以几乎无衰减地通过;而在4.8~6 GHz频段,信号被抑制,对邻频干扰也有一定的抑制作用,使干扰信号在天线等前端设备受到较大衰减,从而改善了通信质量.仿真与测试结果表明,在2.4~2.5 GHz频段滤波天线回波损耗小于-16 dB,驻波比小于1.4;在4.8~6 GHz频段滤波天线回波损耗大于-6.6 dB,驻波比大于2.7.该蓝牙微带天线具有较好的传输特性和滤波功能,满足蓝牙通信传输特性需要.     

Triple-band wireless local area network monopole antenna

A triple-band Bluetooth (BT) and wireless local area network (WLAN) monopole antenna has been proposed based on concepts called capacitive loading/de-loading and inductive loading/de-loading. It has been demonstrated that BT and triple-band WLAN operations, including the BT 2.4 GHz (2.4-2.484 GHz), the WLAN IEEE 802.11 2.4 GHz (2.4-2.484 GHz), 5.2 GHz WLAN (5.15-5.35 GHz) and WLAN 5.8 GHz (5.725- 5.825 GHz) can be achieved by using the monopole antenna with an overall size 8.0 x 11.5 x 1.0 mm³, which is one of the most compact WLAN monopole antennas covering the three frequency bands.     

Dual-band wearable metallic button antennas and transmission in body area networks

A dual-band metallic antenna with the appearance of a button on a pair of jeans for use with wearable computer networks, emergency rescue scenarios and future wireless medical applications is presented. The design operates at 2.4 GHz WLAN and the HiperLAN/2 bands and a parametric study is given to aid the design process together with measurement and simulation of the structure on a body. A study of transmission between pairs of on-body antennas is presented to give insight into on-body propagating line of sight and non-line of sight channels. A term `body gain? is defined to quantify how the body attenuates the channel.     

基于LTCC宽频带双频差分天线的研究与设计

提出了一种新型宽频带双频差分天线.该天线基于低温共烧陶瓷(Low Temperature Co-Fired Ceramies,简称LTCC)技术,采用矩形环状贴片,并使用两条叉形微带馈线进行差分馈电,是一种具有平衡结构的宽缝隙天线,该结构使得天线拥有很宽的频带宽度.天线两频段的中心频率为2.63 GHz和5.13 GH...     

Wi-Fi/WiMAX双极化阵列天线研究

提出一种应用于Wi-Fi/WiMAX的宽带高增益双极化阵列天线.它由+45°和-45°正交极化的两个天线组成。当频率为2.38~2.72 GHz时,天线的回波损耗大于-10 dB;端口1与端口2之间隔离度大于20 dB;端口1在2.45 GHz时获得最大增益为17.14 dBi,端口2在2.483 GHz时获得最大增益为17.15 dBi.仿真和测试很好相吻合,该双极化天线能满足Wi-Fi/WiMAX通信网络要求.     

Modelling of Wideband Concentric Ring Frequency Selective Surface for5GDevices

Frequency selective surfaces (FSSs) play an important role in wireless systems as these can be used as filters, in isolating the unwanted radiation, in microstrip patch antennas for improving the performance of these antennas and in other 5G applications. The analysis and design of the double concentric ring frequency selective surface (DCRFSS) is presented in this research. In the sub-6 GHz 5G FR1 spectrum, a computational synthesis technique for creating DCRFSS based spatial filters is proposed. The analytical tools presented in this study can be used to gain a better understanding of filtering processes and for constructing the spatial filters. Variation of the loop sizes, angles of incidence, and polarization of the concentric rings are the factors which influence the transmission coefficient as per the thorough investigation performed in this paper. A novel synthesis approach based on mathematical equations that may be used to determine the physical parameters of DCRFSS-based spatial filters is presented. The proposed synthesis technique is validated by comparing results from high frequency structure simulator (HFSS), Ansys electronic desktop circuit editor, and an experimental setup. Furthermore, the findings acquired from a unit cell are expanded to a 2 × 2 array, which shows identical performance and therefore proves its stability.     

Reconfigurable patch-antenna design for wideband wireless communication systems

An effective design of a reconfigurable patch antenna, with a wide operational bandwidth for wireless communication and radar systems, is presented in this paper. The reconfigurable patch possesses an E-shaped structure and its operation frequency can be changed by integrated switches. The operational frequency of the antenna can cover an octave frequency range by utilising only two switch states. In state 1, the antenna operates from 9.2 GHz to 15.0 GHz and, in state 2, from 7.5 GHz to 10.7 GHz. Relative bandwidths of 48% and 35% are obtained in the two states, respectively     

Inkjet Printed Metamaterial Loaded Antenna for WLAN/WiMAX Applications

In this paper, the design and performance analysis of an Inkjet-printed metamaterial loaded monopole antenna is presented for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) applications. The proposed metamaterial structure consists of two layers, one is rectangular tuning fork-shaped antenna, and another layer is an inkjet-printed metamaterial superstate. The metamaterial layer is designed using four split-ring resonators (SRR) with an H-shaped inner structure to achieve negative-index metamaterial properties. The metamaterial structure is fabricated on low-cost photo paper substrate material using a conductive ink-based inkjet printing technique, which achieved dual negative refractive index bands of 2.25–4.25 GHz and 4.3–4.6 GHz. The antenna is designed using a rectangular tuning fork structure to operate at WLAN and WiMAX bands. The antenna is printed on 30 × 39 × 1.27 mm3 Rogers RO3010 substrate, which shows wide impedance bandwidth of 0.75 GHz (2.2 to 2.95 GHz) with 2 dB realized gain at 2.4 GHz. After integrating metamaterial structure, the impedance bandwidth becomes 1.25 GHz (2.33 to 3.58 GHz) with 2.6 dB realized gain at 2.4 GHz. The antenna bandwidth and gain have been increased using developed quad SRR based metasurface by 500 MHz and 0.6 dBi respectively. Moreover, the proposed quad SRR loaded antenna can be used for 2.4 GHz WLAN bands and 2.5 GHz WiMAX applications. The contribution of this work is to develop a cost-effective inject printed metamaterial to enhance the impedance bandwidth and realized the gain of a WLAN/WiMAX antenna.     

Effect of conductive yarn crimp in radiation patch on electromagnetic performance of 3D integrated microstrip antenna

A three-dimensionally integrated microstrip antenna (3DIMA) is a microstrip antenna woven into the three-dimensional woven composite for load bearing while functioning as an antenna. In this study, the effect of conductive yarn crimp on electromagnetic performance of 3DIMAs are investigated by designing, simulating and experimental testing of two microstrip antennas with different patch woven structures: one woven in plain weave pattern with most yarn crimp and the other woven orthogonally without yarn crimp. The measured voltage standing wave ratio (VSWR) of the crimp free 3DIMA was 1.05 at the resonant frequency of 1.31 GHz; while that of the crimped 3DIMA was 1.78 at the resonant frequency of 1.41 GHz. In addition, the measured radiation pattern of the crimp free 3DIMA in its radiating patch has smaller back lobe and side lobes than those of the crimped 3DIMA. This result indicates that yarn crimp may have a negative impact on electromagnetic performance of textile structural antennas.     

低交叉极化高隔离的双极化天线

设计了一种应用于WLAN的具有低交叉极化和高隔离度的双极化天线.天线由3层功能层和2层介质基板间隔层叠而成.3层功能层分别为1个方形辐射贴片,2个带有发夹谐振器的馈电网络和1个刻蚀H形缝隙的接地板.发夹谐振器和辐射贴片构成一个二阶滤波天线用以展宽天线的带宽.通过在接地板上蚀刻H形缝隙降低了天线端口间的耦合电流,改善了天线两个端口的隔离度.仿真结果表明,天线的两个端口阻抗带宽分别为2.4 GHz~2.5 GHz和2.39 GHz~2.52 GHz,覆盖WLAN频段(2.4 GHz~2.484 GHz).在天线工作频带内,天线两个端口间的隔离度大于38 dB,天线E面和H面的交叉极化均低于-28 dB.