Issues related to solution chemistry in mercury sampling impingers

Analysis of Hg speciation in combustion flue gases is often accomplished in standardized sampling trains in which the sample is passed sequentially through a series of aqueous solutions to capture and separate oxidized Hg (Hg2+) and elemental Hg (Hg0). Such methods include the Ontario Hydro (OH) and the Alkaline Mercury Speciation (AMS) methods, which were investigated in the laboratory to determine whether the presence of Cl2 and other common flue gas species can bias the partitioning of Hg0 to front impingers intended to isolate Hg2+ species. Using only a single impinger to represent the front three impingers for each method, it was found that as little as 1-ppm Cl2 in a simulated flue gas mixture led to a bias of approximately 10-20% of Hg0 misreported as Hg2+ for both the OH and the AMS methods. Experiments using 100-ppm Cl2 led to a similar bias in the OH method, but to a 30-60% bias in the AMS method. These false readings are shown to be due to liquid-phase chemistry in the impinger solutions, and not necessarily to the gas-phase reactions between Cl2 and Hg as previously proposed. The pertinent solution chemistry causing the interference involves the hypochlorite ion (OCl-), which oxidizes Hg0 to soluble Hg2+. Addition of sodium thiosulfate (Na2S2O3) to the front impinger solutions eliminates this false positive measurement of Hg2+ by selectively reacting with the OCl- ion. In general, the presence of SO2 also mitigates this interference in the same way, and so this bias is not likely to be a factor for Hg speciation measurements from actual coal combustion flue gases. It might, however, be a problem for those few combustor flue gas measurements and research studies where Cl2 is present without appreciable amounts of SO2.     

Effects of sulfur dioxide and nitric oxide on mercury oxidation and reduction under homogeneous conditions

This paper is particularly related to elemental mercury (Hg0) oxidation and divalent mercury (Hg2+) reduction under simulated flue gas conditions in the presence of nitric oxide (NO) and sulfur dioxide (SO2). As a powerful oxidant and chlorinating reagent, Cl2 has the potential for Hg oxidation. However, the detailed mechanism for the interactions, especially among chlorine (Cl)-containing species, SO2, NO, as well as H2O, remains ambiguous. Research described in this paper therefore focused on the impacts of SO2 and NO on Hg0 oxidation and Hg2+ reduction with the intent of unraveling unrecognized interactions among Cl species, SO2, and NO most importantly in the presence of H2O. The experimental results demonstrated that SO2 and NO had pronounced inhibitory effects on Hg0 oxidation at high temperatures when H2O was also present in the gas blend. Such a demonstration was further confirmed by the reduction of Hg2+ back into its elemental form. Data revealed that SO2 and NO were capable of promoting homogeneous reduction of Hg2+ to Hg0 with H2O being present. However, the above inhibition or promotion disappeared under homogeneous conditions when H2O was removed from the gas blend.     

Persulfate oxidation for in situ remediation of TCE. II. Activated by chelated ferrous ion

In situ chemical oxidation (ISCO) is a technique used to remediate contaminated soil and groundwater systems. It has been postulated that sodium persulfate (Na2S2O8) can be activated by transition metal ions such as ferrous ion (Fe2+) to produce a powerful oxidant known as the sulfate free radical (SO4-*) with a redox potential of 2.6 V, which can potentially destroy organic contaminants. In this laboratory study persulfate oxidation of dissolved trichloroethylene (TCE) was investigated in aqueous and soil slurry systems under a variety of experimental conditions. A chelating agent (i.e., citric acid) was used in attempt to manipulate the quantity of ferrous ion in solution by providing an appropriate chelate/Fe2+ molar ratio. In an aqueous system a chelate/Fe2+ molar ratio of 1/5 (e.g., S2O8(2)-/chelate/Fe2+/TCE ratio of 20/2/10/1) was found to be the lowest acceptable ratio to maintain sufficient quantities of Fe2+ activator in solution resulting in nearly complete TCE destruction after only 20 min. The availability of Fe2+ appeared to be controlled by adjusting the molar ratio of chelate/Fe2+. In general, high levels of chelated ferrous ion concentrations resulted in faster TCE degradation and more persulfate decomposition. However, if initial ferrous ion contents are relatively low, sufficient quantities of chelate must be provided to ensure the chelation of a greater percentage of the limited ferrous ion present. Citric acid chelated ferrous ion appeared effective for TCE degradation within soil slurries but required longer reaction times. Additionally, the use of citric acid without the addition of supplemental Fe2+ in soil slurries, where the citric acid apparently extracted native metals from the soil, appeared to be somewhat effective at enhancing persulfate oxidation of TCE over extended reaction times. A comparison of different chelating agents revealed that citric acid was the most effective.     

Comparison of mercury chemistry models

Five mercury (Hg) chemistry models are compared using the same data set for model initialisation. All five models include gas-phase oxidation of Hg(0) to Hg(II) (except for one model), fast reduction–oxidation aqueous reactions between Hg(0) and Hg(II), and adsorption of Hg(II) species to soot particles within droplets. However, the models differ in their detailed treatments of these processes. Consequently, the 48-h simulations reveal similarities but also significant discrepancies among the models. For the simulation that included all Hg species (i.e., Hg(0), Hg(II) and Hg(p)) as well as soot in the initial conditions, the maximum simulated Hg(II) aqueous concentrations ranged from 55 to 148 ng l⁻¹ whereas the minimum concentrations ranged from 20 to 110 ng l⁻¹. These results suggest that further experimental work is critically needed to reduce the current uncertainties in the formulation of Hg chemistry models.     

Effect of solution pH on SO2, NO(x), and Hg removal from simulated coal combustion flue gas in an oxidant-enhanced wet scrubber

This paper presents a study on the simultaneous removal of SO2, NO(x) and Hg (both Hg0 and Hg2+) from a simulated flue gas by oxidant injection in a bench-simulated wet limestone scrubber for a wide range of slurry pH. The slurry pH strongly influenced the chemical mechanism in the scrubber and, therefore, affected pollutant removal. This paper also examines the potential ClO2(gas) reemission from a developed multipollutant scrubber at different slurry pHs. To better understand the chemical mechanisms at each slurry pH and to apply a mass balance to the process, detailed product ion analyses were performed for all experiments. Ion analysis covered three different chlorine species (chlorite, chloride, chlorate), sulfate, nitrite and nitrate. Different NO(x) removal efficiencies and mechanisms were found in acidic and alkaline pHs in the multipollutant scrubber. The acidic solution was favorable for NO and Hg0 oxidation, but increasing the slurry pH above 7.0 was disadvantageous for NO and Hg oxidation/removal. However the rate of NO(x) absorption (by percentage) was higher for the alkaline solution.     

Investigation of selective catalytic reduction impact on mercury speciation under simulated NOx emission control conditions

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NOx) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NOx reduction, promote the formation of oxidized mercury (Hg2+). The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg0) oxidation. Bench-scale experiments were conducted to investigate Hg0 oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO2) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO2 in the flue gases on Hg0 oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg0 to Hg2+ under SCR reaction conditions. The importance of HCl for Hg0 oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg0 oxidation occurring across the SCR reactors in the field.     

Brain glutathione redox system significance for the control of silica-coated magnetite nanoparticles with or without mercury co-exposures mediated oxidative stress in European eel (Anguilla anguilla L.)

This in vitro study investigates the impact of silica-coated magnetite particles (Fe₃O₄@SiO₂/SiDTC, hereafter called IONP; 2.5 mg L^?1) and its interference with co-exposure to persistent contaminant (mercury, Hg; 50 μg L^?1) during 0, 2, 4, 8, 16, 24, 48, and 72 h on European eel (Anguilla anguilla) brain and evaluates the significance of the glutathione (GSH) redox system in this context. The extent of damage (membrane lipid peroxidation, measured as thiobarbituric acid reactive substances, TBARS; protein oxidation, measured as reactive carbonyls, RCs) decreased with increasing period of exposure to IONP or IONP + Hg which was accompanied with differential responses of glutathione redox system major components (glutathione reductase, GR; glutathione peroxidase, GPX; total GSH, TGSH). The occurrence of antagonism between IONP and Hg impacts was evident at late hour (72 h), where significantly decreased TBARS and RC levels and GR and glutathione sulfo-transferase (GST) activity imply the positive effect of IONP + Hg concomitant exposure against Hg-accrued negative impacts [vs. early (2 h) hour of exposure]. A period of exposure-dependent IONP alone and IONP + Hg joint exposure-accrued impact was perceptible. Additionally, increased susceptibility of the GSH redox system to increased period of exposure to Hg was depicted, where insufficiency of elevated GR for the maintenance of TGSH required for membrane lipid and cellular protein protection was displayed. Overall, a fine-tuning among brain glutathione redox system components was revealed controlling IONP + Hg interactive impacts successfully.     

Electrochemical and FTIR studies of the mutual influence of lead(II) or iron(III) and phenol on their adsorption from aqueous acid solution by modified activated carbons

Cyclic voltammetry and spectral FTIR studies of the influence of activated carbon surface modification on the co-adsorption of metal cation (lead or iron) and phenol from aqueous acidic solution were carried out. The diversity in surface chemical structure was achieved by applying different procedures of inorganic matter removal and by modifying the carbon samples in various ways: heating under vacuum, aminoxidation in an ammonia-oxygen atmosphere, oxidation with concentrated nitric acid. The quantities of adsorbed metal ions (Pb(2+) or Fe(3+)) and phenol from solutions containing cation or phenol separately or in a mixture were determined. The adsorption capacity from acidic aqueous acidic solution depends on the chemical properties of the activated carbon surface (e.g., decrease in phenol adsorption with relative lower basicity of the adsorbent). The electrochemical parameters of electrodes made from the carbon samples were estimated, and some possible electrochemical reactions were determined from voltammograms recorded in acid electrolyte solution containing adsorbed species (separately or as a mixture). Relationships were found between metal ion adsorption and electrochemical behavior of Pb(2+)/Pb(4+) and Fe(3+)/Fe(2+) couples on the one hand, and the presence of phenol in the solutions tested and the influence of surface chemistry of the carbon electrodes on electrochemical processes on the other. The changes in adsorption capacity with respect to the adsorbates used and the changes in FTIR spectra of the carbons as a result of adsorption and/or coupling phenol molecules are discussed.     

Influence of HCl on oxidation of gaseous elemental mercury by dielectric barrier discharge process

The influence of HCl on the oxidation of gaseous elemental mercury (Hg0) has been investigated using a dielectric barrier discharge (DBD) plasma process, where the temperature of the plasma reactor and the composition of gas mixtures of HCl, H2O, NO, and O2 in N2 balance have been varied. We observe that Cl atoms and Cl2 molecules, created by the DBD process, play important roles in the oxidation of Hg0 to HgCl2. The addition of H2O to the gas mixture of HCl in N2 accelerates the oxidation of Hg0, although no appreciable effect of H2O alone on the oxidation of Hg0 has been observed. The increase of the reaction temperature in the presence of HCl results in the reduction of Hg0 oxidation efficiency probably due to the deterioration of the heterogeneous chemical reaction of Hg0 with chlorinated species on the reactor wall. The presence of NO shows an inhibitory effect on the oxidation of Hg0 under DBD of 16% O2 in N2, indicating that NO acts as an O and O3 scavenger. At the composition of Hg0 (280 microg m(-3)), HCl (25 ppm), NO (204 ppm), O2 (16%) and N2 (balance) and temperature 90 degrees C, we obtain the nearly complete oxidation of Hg0 at a specific energy density of 8 J l(-1). These results lead us to suggest that the DBD process can be viable for the treatment of mercury released from coal-fired power plants.     

Effects of pH, organic acids, and competitive cations on mercury desorption in soils

The effects of pH, organic acids, and competitive cations on Hg(2+) desorption were studied. Three representative soils for rice production in China, locally referred to as a yellowish red soil (YRS), purplish clayey soil (PCS), and silty loam soil (SLS) and classified as Gleyi-Stagnic Anthrosols in FAO/UNESCO nomenclature, were, respectively, collected from Jiaxin County, Deqing County, and Xiasha District of Hangzhou City, Zhejiang Province. Most of the added Hg(2+) was adsorbed at low initial concentrations (<2 mg l(-1)). Desorption of the adsorbed Hg(2+) in 0.01M KCl (simulating soil solution) was minimal, but was significantly enhanced by the change of pH, and the presence of organic acids or competitive cations. The desorption of Hg(2+) in the soils decreased with pH from 3.0 to 5.0, leveled off at pH 5.0-8.0, but increased with pH from 7.0 to 9.0. The presence of organic ligands enhanced Hg(2+) desorption in the soils except for YRS, in which the addition of tartaric, malic, or oxalic acid reduced Hg(2+) desorption at low concentrations (<10(-4)M), but Hg(2+) desorption generally increased with organic acid concentration. Citric acid was most effective in increasing Hg(2+) desorption, followed by tartaric acid and malic acid; and oxalic acid was the least effective. Desorption of adsorbed Hg(2+) increased with increasing concentrations of added Cu(2+) or Zn(2+). Applied Cu(2+) increased Hg(2+) desorption more than Zn(2+) at the same loading rate. CAPSULE: The effects of organic acids and competitive cations on Hg desorption in soil-water system are related to their concentrations, basic chemical properties, and soil properties.     

Ground discarded tires remove naphthalene, toluene, and mercury from water

Ground discarded tires adsorb naphthalene, toluene, and mercury ions (Hg2+) from aqueous solutions. Their sorption properties and kinetics were determined by batch equilibration techniques at 20 degrees C. The isotherms were linear for naphthalene and toluene and their sorption coefficients were about 1340 and 255 (ml/g), respectively. Sorption of the organic compounds by the ground rubber particles was relatively fast (within 30 min). However, the mercury isotherms were non-linear, and its sorption was slow as compared to the sorption of the organics. The rubber particles had a strong affinity for Hg2+. These results show that ground discarded tires are effective in removing organic compounds and Hg2+ from wastewater and other contaminated environments. In addition it would be a useful, environmentally friendly use of discarded tires (one tire per year per capita is discarded in the United States).     

巯基化合物在万寿菊镉解毒中的作用

采用水培实验方法研究了万寿菊体内镉积累和解毒与巯基化合物含量的关系。万寿菊植株分别在镉浓度为0、0.1、0.5、2和8 mg/L的营养液中暴露7 d,测定了根、茎、叶中镉、非蛋白巯基(NPT)、半胱氨酸(Cys)、γ-谷氨酰半胱氨酸(γ-EC)、谷胱甘肽(GSH)和植物络合素(PCs)的含量。植物根、茎、叶中镉含量都随着镉暴露浓度的增加而增加。当溶液中镉浓度较低(0.1～2 mg/L)时,茎叶中NPT、PCs、Cys和γ-EC含量随着镉浓度增加而增大;当镉浓度较高(8 mg/L)时,茎叶中PCs含量迅速降低,GSH含量大幅度增高。在根部,这些巯基化合物的含量几乎不受镉处理影响,且含量较低。以上研究结果表明:PCs在万寿菊镉的解毒机制中发挥一定的作用,暴露于高浓度的镉,GSH比PCs起着更为重要的解毒作用。     

4A沸石去除水中Pb~(2+)的研究

在静态条件下,研究了4A沸石对废水中Pb2+的吸附性能,并探讨了影响吸附的因素。实验表明:当温度为30℃,废水pH为5~6,0.01 g4A沸石对100 mg/LPb2+溶液10 mL吸附20 min,Pb2+的去除率可达到99%以上。在实验研究条件下,4A沸石对Pb2+的吸附符合Langmuir和Freundlich等温吸附方程,相关系数为0.9819和0.9998。经计算,4A沸石对Pb2+的饱和吸附量为125 mg/g。4A沸石吸附水中Pb2+,达到吸附平衡的时间较短;溶液pH值的变化对吸附效果影响不显著;温度从室温略微升高,Pb2+的去除率略有增大。吸附在4 A沸石上的Pb2+可回收利用,处理后的4A沸石可以再生,且重复使用性能较好。     

不同阳离子对Fe~0还原硝酸盐的影响

由于水中硝酸盐污染的普遍性、难去除性和对人体健康的潜在危害性而引起人们的广泛关注。通过批实验,考察了不同阳离子(Fe2+、Fe3+和Cu2+)对Fe0还原硝酸盐的影响。结果表明,由于加入阳离子可直接或间接地增加溶液中的Fe2+而都能促进硝酸盐的还原,作用顺序为Fe3+Fe2+Cu2+;Fe2+对硝酸盐的还原具有重要作用,并随着反应的进行,转化为铁氧化物附着在铁表面而降低铁的活性;硝酸盐还原的主要产物为氨氮,亚硝酸盐只在反应初期有少量积累,尤其是加Cu2+的体系中,但随后都很快降低;在所有体系中,检测到的三氮(NO3--N、NO2--N和NH4+-N)之和只占理论总氮的51.5%~82.6%;动力学分析表明,硝酸盐的还原在不加阳离子的体系中更符合一级反应,而加了阳离子的处理更符合Lo-gistic模型。本研究结果阐明了Fe2+对Fe0还原硝酸盐的重要性。     

Enhanced photocatalytic reduction reaction over Bi(3+)-TiO(2) nanoparticles in presence of formic acid as a hole scavenger

A series of Bi(3+)-doped TiO(2) (Bi(3+)-TiO(2)) catalysts with a doping concentration up to 2wt% were prepared by a sol-gel method. The prepared photocatalysts were characterized by different means to determine their chemical composition, surface structure and light absorption properties. The photocatalytic activity of different Bi(3+)-TiO(2) catalysts was evaluated in the photocatalytic reduction of nitrate in aqueous solution under UV illumination. In the experiments, formic acid was used as a hole scavenger to enhance the photocatalytic reduction reaction. The experiments demonstrated that nitrate was effectively degraded in aqueous Bi(3+)-TiO(2) suspension by more than 83% within 150min, while the pH of the solution increased from 3.19 to 5.83 due to the consumption of formic acid. The experimental results indicate that the presence of Bi(3+) in TiO(2) catalysts substantially enhances the photocatalytic reaction of nitrate reduction. It was found that the optimal dosage of 1.5wt% Bi(3+) in TiO(2) achieved the fastest reaction of nitrate reduction under the experimental condition. Bismuth ions deposit on the TiO(2) surface behaves as sites where electrons accumulate. Better separation of electrons and holes on the modified TiO(2) surface allows more efficient channeling of the charge carriers into useful reduction and oxidation reactions rather than recombination reactions. Two intermediate products of nitrite and ammonia during the reaction were also monitored to explore the possible mechanisms of photoluminescence quenching and photocatalytic reduction in the context of donor-acceptor interaction with electron trapping centers.     

Biological detection and analysis of mercury toxicity to alfalfa (Medicago sativa) plants

Mercury has become one of the major causes of toxic metal pollution in agricultural lands. Accumulation of mercury by plants may disrupt many cellular functions and block growth and development. To assess mercury toxicity, we performed an experiment focusing on the responses of alfalfa (Medicago sativa) to Hg(2+)-induced oxidative stress. Alfalfa plants were treated with 0-40microM HgCl(2) for 7d. The concentrations of Hg(2+) were positively correlated with the generation of O2- and H(2)O(2) in leaves. Treatment with Hg(2+) increased the activities of NADH oxidase and lipoxygenase (LOX) and damaged the biomembrane lipids. To understand biochemical responses under Hg stress, activities of several antioxidant enzymes, superoxide dismutase (SOD), peroxidase (POD), catalase (CAT), ascorbate peroxidase (APX) and glutathione reductase (GR) were assayed. Analysis of SOD activity by non-denaturing polyacrylamide gel electrophoresis revealed five isoforms in leaves, but they showed different patterns. Also, eight isoenzymes of APX and seven of POD in leaves were detected. However, only one isoform of CAT was visualized. The total activities of APX, POD and CAT were generally enhanced. We also measured several antioxidative metabolites such as ascorbate and glutathione (GSH), and found that both differentially accumulated in leaves. These results indicate that the increased levels of O2- and H(2)O(2) under Hg stress were closely linked to the improved capacity of antioxidant enzymes. The data not only provide the important information for better understanding of the toxic and tolerance mechanisms, but as well can be used as a bio-indicator for soil contamination by Hg.     

Catalytic oxidation of pentachlorophenol in contaminated soil suspensions by Fe+3-resin/H2O2

Pentachlorophenol (PCP) is a wood preserving agent that is commonly found in contaminated soils at wood treatment sites. The catalytic properties of Fe+3-resin for the oxidation of PCP in aqueous solution and soil suspension with H2O2 were tested. Batch tests in aqueous solution were performed at various dosages of catalyst and H2O2, and reaction temperatures. The results showed that the oxidation of PCP in aqueous solution depends on the dose of H2O2 and the temperature. Essentially complete oxidation of 100 mgl(-1) PCP was obtained with 0.5% Fe+3-resin catalyst, 0.1 M H2O2 and at a reaction temperature of 80 degrees C. The oxidation of PCP achieved in three different soil suspensions was more than 94% within 30-50 min. Moreover, it was demonstrated that the same Fe+3-resin could be reused for at least six cycles of PCP oxidation in soil solutions without loss in efficiency unless the pH of the reaction falls below 5. It was proposed that the loss in used Fe+3-resin catalyst activity could be related to the leaching of Fe+3 at low pH.     

Treatment of phenylmercury salts by heterogeneous photocatalysis over TiO(2)

UV/TiO(2) photocatalysis of phenylmercury salts in aqueous solutions has been performed starting from both acetate (C(6)H(5)HgCH(3)CO(2), PMA) and chloride (C(6)H(5)HgCl, PMC) salts, in the presence or the absence of oxygen at acidic pH. Removal of Hg(II) in solution took place with the simultaneous deposit of dark or pale gray solids on the photocatalyst, identified as metallic Hg (when starting from PMA) or mixtures of Hg(0) and Hg(2)Cl(2) (when starting from PMC). Partial mineralization of the organic part of both compounds has also been achieved. Hg(II) removal and mineralization were enhanced in the absence of oxygen. PMA photocatalysis followed a saturation kinetics, going from first order at low concentration to zero order at higher concentrations (>0.5mM). For PMA, reaction was faster at high pH (11) with formation of mixtures of Hg and HgO. Phenol was detected as a product of the reaction in both cases, PMA and PMC, and no formation of dangerous methyl- or ethylmercury species was observed in the first case. A mechanism for the photocatalytic reaction has been proposed. The fact that calomel was found as a deposit when starting from PMC under nitrogen suggests that the mechanism of Hg(II) transformation proceeds through successive one-electron transfer reactions passing by mercurous forms.     

Investigation of Selective Catalytic Reduction Impact on Mercury Speciation under Simulated NOx Emission Control Conditions

Abstract

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NO_x) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NO_x reduction, promote the formation of oxidized mercury (Hg²⁺).

The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg⁰) oxidation. Bench-scale experiments were conducted to investigate Hg⁰ oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO₂) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO₂ in the flue gases on Hg⁰ oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg⁰ to Hg²⁺ under SCR reaction conditions. The importance of HCl for Hg⁰ oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg⁰ oxidation occurring across the SCR reactors in the field.     

Issues Related to Solution Chemistry in Mercury Sampling Impingers

ABSTRACT

Analysis of Hg speciation in combustion flue gases is often accomplished in standardized sampling trains in which the sample is passed sequentially through a series of aqueous solutions to capture and separate oxidized Hg (Hg²⁺) and elemental Hg (Hg⁰). Such methods include the Ontario Hydro (OH) and the Alkaline Mercury Speciation (AMS) methods, which were investigated in the laboratory to determine whether the presence of Cl₂ and other common flue gas species can bias the partitioning of Hg⁰ to front impingers intended to isolate Hg²⁺ species. Using only a single impinger to represent the front three impingers for each method, it was found that as little as 1-ppm Cl₂ in a simulated flue gas mixture led to a bias of approximately 10-20% of Hg⁰ misreported as Hg²+ for both the OH and the AMS methods. Experiments using 100-ppm Cl₂ led to a similar bias in the OH method, but to a 30-60% bias in the AMS method. These false readings are shown to be due to liquid-phase chemistry in the impinger solutions, and not necessarily to the gas-phase reactions between Cl₂ and Hg as previously proposed. The pertinent solution chemistry causing the interference