Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Electrocatalytic oxidation of sulfite by acetylferrocene at glassy carbon electrode

The electrochemical oxidation of sulfite catalyzed by acetylferrocene (AFc) at a glassy carbon electrode (GCE) in 0.2 M NaClO₄ aqueous solution has been studied by cyclic voltammetry. Although sulfite itself showed a sluggish electrochemical response at the GCE, the response could be enhanced greatly by using AFc as a mediator, which enables a sensitive determination of the substrate (sulfite). The reaction rate constant for catalytic oxidation was evaluated as (7.02 ± 0.05) × 10⁴ M ^?1 s^?1 by chronoamperometry. Experimental conditions that maximize the current efficiency of the electrocatalytic oxidation, such as the pH and both the catalyst (AFc) and substrate (sulfite) concentrations, were also investigated. The electrochemical kinetics of electrocatalytic oxidation of sulfite by AFc has been studied by cyclic voltammetry. In the presence of 5 × 10^?4 M AFc, the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 2 × 10^?4–2.4 × 10^?3 M . This result can be applied in the determination of real samples. Copyright © 2005 John Wiley & Sons, Ltd.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

L‐Cysteine Voltammetry at a Carbon Paste Electrode Bulk‐Modified with Ferrocenedicarboxylic Acid

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenedicarboxylic acid modified carbon paste electrode (FDCMCPE) in aqueous media using cyclic voltammetry, differential pulse voltammetry and double potential step chronoamperometry. It has been found that under optimum condition (pH 8.00) in cyclic voltammetry, the oxidation of L ‐cysteine occurs at a potential about 200 mV less positive than that of an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α, and catalytic reaction rate constant, k_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear analytical curves were obtained in the ranges of 3.0×10^?5 M–2.2×10^?3 M and 1.5×10^?5 M–3.2×10^?3 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 2.6×10^?5 M and 1.4×10^?6 M by CV and DPV methods.     

Electrocatalytic Oxidation and Voltammetric Determination of L‐Cysteic Acid at the Surface of p‐Bromanil Modified Carbon Paste Electrode

The electrochemical properties of L ‐cysteic acid studied at the surface of p‐bromanil (tetrabromo‐p‐benzoquinone) modified carbon paste electrode (BMCPE) in aqueous media by cyclic voltammetry (CV) and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteic acid at the surface of BMCPE occurs at a half‐wave potential of p‐bromanil redox system (e.g., 100 mV vs. Ag|AgCl|KCl_sat), whereas, L ‐cysteic acid was electroinactive in the testing potential ranges at the surface of bare carbon paste electrode. The apparent diffusion coefficient of spiked p‐bromanil in paraffin oil was also determined by using the Cottrell equation. The electrocatalytic oxidation peak current of L ‐cysteic acid exhibits a linear dependency to its concentration in the ranges of 8.00×10^?6 M–6.00×10^?3 M and 5.2×10^?7 M–1.0×10^?5 M using CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 5.00×10^?6 M and 4.00×10^?7 M by CV and DPV methods. This method was used as a new, selective, rapid, simple, precise and suitable voltammetric method for determination of L ‐cysteic acid in serum of patient's blood with migraine disease.     

Nanostructured Base Electrochemical Sensor for Simultaneous Quantification and Voltammetric Studies of Levodopa and Carbidopa in Pharmaceutical Products and Biological Samples

A novel carbon paste electrode modified with carbon nanotubes and 5‐amino‐2′‐ethyl‐biphenyl‐2‐ol (5AEB) was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of levodopa (LD) and carbidopa (CD), is described. Cyclic voltammetry (CV) was used to investigate the redox properties of this modified electrode at various scan rates. The apparent charge transfer rate constant, k_s, and transfer coefficient, a, for electron transfer between 5AEB and CPE were calculated as 17.3 s^?1 and 0.5, respectively. Square wave voltammetry (SWV) exhibits a linear dynamic range from 2.5×10^?7 to 2.0×10^?4 M and a detection limit of 9.0×10^?8 M for LD.     

Selective determination of cysteine in the presence of tryptophan by carbon paste electrode modified with quinizarine

A sensitive and selective electrochemical method for the determination of L-cysteine was developed using a modified carbon paste electrode (MCPE) with quinizarine. Cyclic voltammetry was used to investigate the redox properties of this modified electrode at various solution pH values and at various scan rates. The apparent charge transfer rate constant, ks and transfer coefficient for electron transfer between quinizarine and carbon paste electrode (CPE) were calculated as 2.76 s^?1 and 0.6, respectively. This modified carbon paste electrode shows excellent electrocatalytic activity toward the oxidation of L-cysteine in a phosphate buffer solution (pH 7.0). The linear range of 1.0 × 10^?6 to 1.0 × 10^?3 M and a detection limit (3s) of 2.2 × 10^?7 M were observed in pH 7.0 phosphate buffer solutions. In differential pulse voltammetry, the quinizarine modified carbon paste electrode (QMCPE) could separate the oxidation peak potentials of L-cysteine and tryptophan present in the same solution, though at the unmodified CPE the peak potentials were indistinguishable. This work introduces a simple and easy approach to selective detection of L-cysteine in the presence of tryptophan. Also, the modified electrode was employed for the determination of L-cysteine in the real samples such as serum of blood and acetylcysteine tablet.     

Voltammetric determination of droxidopa in the presence of carbidopa using a nanostructured base electrochemical sensor

A novel carbon paste electrode modified with ZnO nanorods and 2-(4-oxo-3-phenyl-3,4-dihydroquinazolinyl)-N′-phenyl-hydrazinecarbothioamide (2PHCZNCPE) was fabricated and employed to study the electrocatalytic oxidation of droxidopa, using cyclic voltammetry, chronoamperometry and square wave voltammetry as diagnostic techniques. It has been found that the oxidation of droxidopa at the surface of modified electrode occurs at a potential of about 435 mV less positive than that of an unmodified carbon paste electrode. Square wave voltammetry exhibits a linear dynamic range from 7.0 × 10^–8 to 3.0×10^?4 M and a detection limit of 45.0 nM for droxidopa. Finally this modified electrode was used for simultaneous determination of droxidopa and carbidopa.     

Electrocatalytic Characteristics of Ferrocenecarboxylic Acid Modified Carbon Paste Electrode in the Oxidation and Determination of L‐Cysteine

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenecarboxylic acid modified carbon paste electrode (FCMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteine is occurs at a potential about 580 mV less positive than that an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and catalytic reaction rate constant, K′_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear calibration curves were obtained in the ranges of 10^?5 M–10^?3 M and 4.1×10^?8 M–3.7×10^?5 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (2δ) were determined as 2.4×10^?6 M and 2.5×10^?8 M by CV and DPV methods. This method was also examined for determination of L ‐cysteine in some samples, such as Soya protein powder, serum of human blood by using recovery and standard addition methods.     

Electrochemical Analysis of D‐Penicillamine Using a Carbon Paste Electrode Modified with Ferrocene Carboxylic Acid

The electrochemical behavior of D ‐penicillamine (D ‐PA) studied at the surface of ferrocene carboxylic acid modified carbon paste electrode (FCAMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00), the oxidation of D ‐PA at surface of such an electrode is occurred about 420 mV less positive than that an unmodified carbon paste electrode (CPE). The catalytic oxidation peak current was linearly dependent on the D ‐PA concentration and a linear calibration curve was obtained in the ranges 7.5×10^?5 M – 1.0×10^?3 M and 6.5×10^?6 M?1.0×10^?4 M of D ‐PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 6.04×10^?5 M and 6.15×10^?6 M. This method was also used for the determination of D ‐PA in pharmaceutical preparation (capsules) by standard addition method.     

Poly(ortho‐toluidine) Modified Carbon Paste Electrode: A Sensor for Electrocatalytic Reduction of Nitrite

The electrocatalytic reduction of nitrite has been studied by poly(ortho‐toluidine) films modified carbon paste electrode (P‐OT/MCPE). Cyclic voltammetry and chronoamperometry techniques were used to investigate the suitability of poly(ortho‐toluidine) as a mediator for the electrocatalytic nitrite reduction in aqueous solution with various pH. Results showed that pH 0.00 is the most suitable for this purpose. In the optimum pH, the reduction of nitrite occurs at a potential about 600 mV more positive than unmodified carbon paste electrode. The catalytic reaction rate constant, (k_h), was calculated 8.68×10² M^?1 s^?1 by the data of chronoamperometry. The catalytic reduction peak current was linearly dependent on the nitrite concentration and the linearity range obtained was 5.00×10^?4 M–1.90×10^?2 M. Detection limit has been found to be 3.38×10^?4 M (2σ). This method has been successfully employed for quantification of nitrite in real sample.     

Electrocatalytic Oxidation of Hydrazine at the Poly(Glutamic Acid) Chemically Modified Electrode and Its Amperometric Determination

ABSTRACT

The electrochemical polymerization of glutamic acid at the glassy carbon electrode was investigated in phosphate buffer solution by cyclic voltammetry. The applied voltage range, pH of electrolyte, cyclic number were explored for optimal polymerization conditions. The resulting film exhibits an electrocatalytic ability to hydrazine, reducing the overpotential by 500mV. The electrocatalytic response of hydrazine is evaluated with regard to pH, scan rate, applied voltage, hydrazine concentration and other variables. The rate constant of the catalytic reaction was 1.2 × 10⁴ M^?1.s^?1. When used as amperometric detector, the modified electrode yields a detection limit of 1 × 10^?8 M hydrazine. The electrode is rather stable even after use for a month and a reproducible response was obtained.     

Simultaneous determination of catechol and hydroquinone by carbon paste electrode modified with hydrophobic ionic liquid-functionalized SBA-15

Hydrophobic ionic liquid-functionalized SBA-15 modified carbon paste electrode (CPSPE) was fabricated, and its electrochemical performance was investigated by cyclic voltammetry, electrochemical impedance spectra, and chronocoulometry in K₃Fe(CN)₆/K₄Fe(CN)₆ solution. Compared with carbon paste electrode (CPE) and SBA-15 modified carbon paste electrode (CSPE), the electron transfer ability was in the sequence as: CPSPE>CSPE>CPE. Meanwhile, the electrocatalytic activity of CPSPE to catechol and hydroquinone was evaluated by cyclic voltammetry, and then, the linear concentration ranges were obtained by the amperometric detection from 2.0?×?10^-5 to 3.2?×?10^-4 M for catechol and 5.0?×?10^-5 to 5.5?×?10^-4 M for hydroquinone, with the detection limits of 5.0?×?10^-7 and 6.0?×?10^-7 M, respectively. The advantages of both ionic liquids and heterogeneous supports made CPSPE exhibit high electrocatalytic activity towards the redox of catechol and hydroquinone by significantly improving their reversibility and enhancing their peak currents. In addition, the present method was applied to the determination of catechol and hydroquinone in artificial wastewater sample, and the results were satisfactory.     

Electrocatalytic Oxidation of Sulfite on a Cobalt Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode

The electrocatalytic oxidation of sulfite has been studied on the cobalt pentacyanonitrosylferrate modified glassy carbon electrode (CoPCNF). The CoPCNF films on the glassy carbon electrodes show an excellent electrocatalytic activity toward the oxidation of sulfite in 0.5 M KNO₃. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry, rotating disk electrode (RDE) voltammetry and chronoamperometry. The average value of the rate constant, K, for the catalytic reaction and the diffusion coefficient, D, were evaluated by different approaches for sulfite and found to be 2.9×10² M^?1s^?1 and 4.6×10^?6 cm²s^?1, respectively. At a fixed potential under hydrodynamic conditions (stirred solutions), the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 5×10^?6–1×10^?4 M. The detection limit of the method is 3×10^?6 M., low enough for the trace sulfite determination.     

First Electrochemical Report for Simultaneous Determination of Norepinephrine,Tyrosine and Nicotine Using a Nanostructure Based Sensor

A carbon paste electrode was modified with ZnO nanorods and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,4′AAZCPE) to cause electrocatalysis of norepinephrine oxidation. It has been found that the oxidation of norepinephrine at the surface of modified electrode occurs at a potential of about 180 mV less positive than that of an unmodified carbon paste electrode. Square wave voltammetry (SWV) exhibits linear dynamic range from 1.0×10^?7 to 8.0×10^?5 M and a detection limit of 3.9×10^?8 M for norepinephrine. In addition, this modified electrode was used for simultaneous determination of norepinephrine, tyrosine and nicotine.     

Differential Pulse Voltammetric Determination of Montelukast in Tablets and Human Plasma by Using Chitosan Modified Carbon Paste Electrode

Electrochemical reduction and determination of montelukast (MKS) was studied in methanol – 0.1 M HCl solution (1 : 1, v/v) by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) at chitosan modified carbon paste electrode. The linear range was 1.70×10^?7–1.83×10^?5 M for DPV analysis. Limit of detection (LOD) and limit of quantification (LOQ) were 5.32×10^?8 M and 1.61×10^?7 M, respectively. The developed method was successfully applied to the determination of MKS in tablets and spiked human plasma. The results obtained were in good agreement with those obtained using a reported spectrofluorimetric technique.     

Electrocatalytic oxidation of methanol by ZSM-5 nanozeolite-modified carbon paste electrode in alkaline medium

Development of a novel modified electrode for electrocatalytic oxidation of methanol in order to decrease overvoltage is importance. In this paper, carbon paste electrode (CPE) was modified by ZSM-5 nanozeolite. The average diameter of used nanozeolite was 97 nm. Ni²⁺ ions were incorporated to the nanozeolite by immersion of the modified electrode in a 0.1 M nickel chloride solution. Then, electrochemical studies of this electrode were performed by using cyclic voltammetry(CV) in alkaline medium. This modified electrode was used as an anode for the electrocatalytic oxidation of methanol in 0.1 M of NaOH solution. The obtained data demonstrated that ZSM-5 nanozeolite at the surface of CPE improves catalytic efficiency of the dispersed nickel ions toward methanol oxidation. The values of electron transfer coefficient, charge-transfer rate constant, and the electrode surface coverage are obtained 0.61, 0.2342 s^?1, and 4.33 × 10^?8 mol cm^?2, respectively. Also, the mean value of catalytic rate constant between the methanol and redox sites of electrode and diffusion coefficient were found to be 2.54 × 10⁴ cm³ mol^?1 s^?1 and 1.85 × 10^?8 cm² s^?1, respectively. Obtained results from both CV and chronoamperometric techniques indicated that the electrode reaction is a diffusion-controlled process.     

A Simple and Efficient Electrochemical Sensor for Electrocatalytic Reduction of Nitrite Based on Poly(4‐aminoacetanilide) Film Using Carbon Paste Electrode

In this study, the electrochemical reduction of nitrite was investigated on poly(4‐aminoacetanilide) (PPAA) forming by cyclic voltammetry at the surface of carbon paste electrode. The electrochemical properties of the modified electrode have been studied by cyclic voltammetry and double potential step chronoamperometry. Results showed that in the optimum condition (pH = 0.00) the reduction of nitrite occurred at a potential about 667 mV more positive than that unmodified carbon paste electrode. This amount of electrocatalytic ability is high compared with other electrocatalysts. Using a chronoamperometric method, the catalytic rate constant (k) was calculated 8.4 × 10⁴ cm³ mol^‐1 s^‐1. Also, the electrocatalytic reduction peak currents was found to be linear with the nitrite concentration in the ranges of 5 × 10^‐4 M to 2.5 × 10^‐2 M and 2 × 10^‐5 M to 7 × 10^‐3 M with detection limits (2σ) were determined as 4.5 × 10^‐4 M and 1 × 10^‐5 M by cyclic voltammetry (CV) and hydrodynamic amperometry methods respectively. Recovery experiments exhibit the satisfactory results.     

Electrocatalytic Oxidation and Determination of Cysteamine by Poly‐N,N‐dimethylaniline/Ferrocyanide Film Modified Carbon Paste Electrode

Functionalized poly‐N,N‐dimethylaniline film was prepared by adsorption of ferrocyanide onto the polymer forming at the surface of carbon paste electrode (CPE) in aqueous solution by using potentiostatic method. The electrocatalytic ability of poly‐N,N‐dimethylaniline/ferrocyanide film modified carbon paste electrode (PDMA/FMCPE) was demonstrated by oxidation of cysteamine. Cyclic voltammetry and chronoamperometry techniques were used to investigate this ability. Results showed that pH 7.00 is the most suitable for this purpose. It is found that the catalytic reaction rate constant, (k_h), is equal to 2.142×10³ M^?1 s^?1 by the data of chronoamperometry. The catalytic reduction peak current was linearly dependent on the cysteamine concentration and the linearity range obtained was 8.00×10^?5 M–1.14×10^?2 M. Detection limit was determined 7.97×10^?5 M (2σ). This method has been successfully employed for quantification of cysteamine in real sample.