Nd3+A位置换对(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷微波介电性能的影响

研究了Nd3+离子A位置换改性(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷的微波介电性能.[(Pb0.5Ca0.5)1-xNdx](Fe0.5Nb0.5)O3(PCNFN)陶瓷的微波介电性能得到改善是由于少量过剩的Nd3+与(Pb,Ca)2+的固溶能够消除氧空位.当x=0.02时,能够形成单相的钙钛矿相,随着Nd3+置换量的增加,过剩的Nd3+将导致第二相焦绿石的形成,焦绿石会恶化PCNFN的微波介电性能.PCNFN介电性能随x的增加而下降是由于焦绿石相随x增加的结果.当x=0.02-0.05,PCNFN陶瓷有很好的微波介电性能,介电常数K>100,Qf值为5385-5797GHz,频率温度系数TCF随Nd3+含量的增加从正的变为负的.     

半化学法制备（Bi2-xNdx）（Zn1/3Nb2/3）2O7微波介电陶瓷与介电性能的研究

采用半化学法制备微波介电陶瓷（Bi2-xNdx）（Zn1/3Nb2/3）2O7（0≤x≤0.6），系统地研究了陶瓷的相结构及低频介电性能。结果表明：当Nd^3＋取代量较少伍≤0．25）时，样品的相结构仍然保持单斜焦绿石单相，随着Nd^3＋取代量的进一步增加，样品中出现立方焦绿石相，样品结构呈现单斜相与立方相的共存。同时，样品的介电性能随Nd^3＋取代量的变化为：介电常数先增大后减小，而介电损耗先减小后增大，在X=0.25处取得最佳电性能，分另1是εr=83，tanδ=0．0029（100kHz）。     

工艺因素对Bi2O3、MnO2掺杂[(Pb,Ca)La](Fe,Nb)O3陶瓷体系微波介质性能的影响

研究了烧结工艺对Bi2O3及MnO2掺杂[(Pb0.5Ca0.5)0.92 La0.08](Fe0.5 Nb0.5)O3陶瓷体系显微结构及介电性能的影响.研究表明Bi2O3及MnO2的加入可降低体系的烧结温度100～140℃,同时提高体密度.XRD图谱、SEM及微波介电性能证明950℃是最佳的煅烧温度.烧结温度对晶粒形貌有显著影响,随烧结温度的增加晶粒尺寸不断增加,但超过一定值后不断减小的气孔率又会增加.当掺杂物的质量比(Bi2O3/MnO2)K=1,掺杂物质量百分含量W=1%,烧结条件为1050℃,保温4h,体系微波介电性能可达εr=91.1,Qf=4870GHz,τf=1.85×10-5/℃.     

Zr4+B位置换对(Pb0.5Ca0.5)(Fe(0.5)Nb0.5)O3

研究了Zr4+离子B位置换改性对(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷微波介电性能.实验结果表明,(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3(PCFNZ)陶瓷样品呈现单一斜方钙钛矿相结构.随Zr(4+)离子的置换量增加,PCFNZ陶瓷体系的Qr值和晶粒尺寸逐渐减小;介电常数εr随着置换量增加...     

Ba置换改性(Ca1-xBax)[(Mg1/3Nb2/3)0.6Ti0.4]O3陶瓷结构与微波介电性能的研究

研究了Ba置换改性对Ca [(Mg1/3Nb2/3)0.6Ti0.4]O3陶瓷微观结构与介电性能的影响.通过XRD与SEM分析发现,当x=0.15,(Ca1-xBax) [(Mg1/3Nb2/3)0.6Ti0.4]O3形成了正交晶系钙钛矿结构的单相固溶体;当x=0.20～0.80时,改性陶瓷为正交与六方钙钛矿结构的两相复合固溶体;当x=0.85 时,所形成(Ca0.15Ba0.85) [(Mg1/3Nb2/3)0.6Ti0.4]O3陶瓷为六方钙钛矿结构的单相固溶体.(Ca1-xBax) [(Mg1/3Nb2/3)0.6Ti0.4]O3系陶瓷微波介电性能的变化与Ba在材料内部的分布状态密切相关,与基材CMNT陶瓷相比:当x=0.15时,陶瓷的介电常数提高,介电损耗降低,谐振频率温度系数向负方向移动:εr=55,Qf值=32000GHz(6.5GHz下),τf=-36.82ppm/℃;当x=0.20～0.80间变化时,(Ca1-xBax)[(Mg1/3Nb2/3)0.6Ti0.4]O3两相复合陶瓷的微波介电性能由于复合效应而表现出连续变化的规律:εr= 45～33 ,Qf值= 30500～40200GHz(6.3GHz～7.6GHz下),τf = -17.7～12.52ppm/℃;当x=0.85时,单相钙钛矿固溶体(Ca0.15Ba0.85) [(Mg1/3Nb2/3)0.6Ti0.4]O3获得良好的微波介电性能:εr=31,Qf值达到44000GHz(8.5GHz下),τf=10.81ppm/℃.     

(1-y)Ca1-xLa2x/3 TiO3-yCa(Mg1/3 Nb2/3)O3系陶瓷的缺位结构与微波介电性能研究

采用固相合成法制备了(1-y)Ca1-xLa2x/3 TiO3-yCa(Mg1/3Nb2/3)O3系列固溶体陶瓷材料,研究了该体系微波介电性能与微观结构的关系.研究结果表明:当体系组成为0.5Cao6Lao267 TiO3-0.5Ca(Mg1/3Nb2/3)O3时,在1400℃下烧结保温4小时所得到材料的微波介电性能最佳:εr=55,Q×f值=45000GHz(7.6GHz下),τf=0.04×10-6/℃.同时还探讨了三价阳离子La3 固溶时产生的A点缺陷Vca2 对固溶体结构及微波介电性能的影响.     

MnO2对Ba(Mg1/3Nb2/3)O3微观结构和微波介电性能的影响

研究了MnO2助烧剂对Ba(Mg1/3Nb2/3)O3陶瓷的微观结构和微波介电性能.MnO2可以有效地使Ba(Mg1/3Nb2/3)O3陶瓷的致密化温度由1550℃降低到1400℃左右.随MnO2掺量的增加,Ba(Mg1/3Nb2/3)O3陶瓷的12超晶格衍射峰的强度减弱,但是没有第二相出现.1400℃烧结4h陶瓷的晶粒尺寸在1.5μm左右.MnO2的掺入改善了Ba(Mg1/3Nb2/3)O3陶瓷的微波介电性能,MnO2掺量为1%mol的Ba(Mg1/3Nb2/3)O3陶瓷具有最好的微波介电性能εr≈31.5,Qf=68000,τf=3.11×10-5/℃,这可归功于陶瓷具有相当高的相对密度.     

Bi2O3掺杂对Mg4Nb2O9陶瓷的微结构及微波介电性能的影响

采用固相反应法制备了Mg4Nb2O9基微波介质陶瓷,研究了Bi2O3掺杂对Mg4Nb2O9陶瓷烧结行为、相结构、显微结构及微波介电性能的影响。实验结果表明:Mg4Nb2O9陶瓷烧结温度随Bi2O3掺杂量的增加而减小,添加2.0wt%Bi2O3,烧结温度从1350℃降低至1175℃;随Bi2O3添加量从0.0wt%增大到3.0wt%,最强峰(104)晶面间距d值由2.756nm增大至2.769nm;Mg4Nb2O9陶瓷的微波介电性能随Bi2O3掺杂量增加而变化;掺杂2.0wt%Bi2O3的Mg4Nb2O9陶瓷在1175℃保温2小时烧结,获得亚微米级陶瓷,且具有最佳的微波介电性能,εr为12.58,Q×f为71949.74GHz。     

Fe2O3掺杂MgTiO3-CaTiO3微波陶瓷的介电性能研究

采用固相法制备0.93MgTiO3-0.07CaTiO3-xFe_2O_3(摩尔分数x=0.01~0.025)微波介质陶瓷材料,研究添加Fe_2O_3后,体系的晶体结构、显微结构和微波介电性能之间的变化规律。利用XRD、SEM、网络分析仪对样品的相组成、微观结构、介电性能进行测试分析。研究表明:该复合陶瓷样品的致密度、介电常数和Q·f值随Fe_2O_3含量的增加先增大后减小。当x(Fe_2O_3)为0.015,在1290℃烧结4h时,获得最优的介电性能:εr=21.32,Q·f=37448GHz,τf=0.577×10-6/℃。     

Ca[(Li_(1/3)Nb_(2/3))_(0.8)Sn_(0.2)]O_(3-δ)-xTiO_2陶瓷的微波介电特性

研究了Ca[(Li1/3Nb2/3)0.8Sn0.2]O3-δ-xTiO2(0≤2≤0.2)陶瓷的微观结构及微波介电特性.当0≤x≤10%(摩尔分数,下同)时,体系为单一钙钛矿相.随Ti4+含量的增加,B位1:2有序度下降,品质因素减小,谐振频率温度系数先由-22.6×10-6/℃增加到-11.1×10-6/℃,然后向负值方向移动.当Ti4+含量为10%时,陶瓷微波介电性能最佳:εr=29.3,Qf=2684GHz,τf=-11.1×10-6/℃.     

La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2合金的储氢性能研究

针对两种新型稀土型储氢合金La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2的储氢特性进行研究分析。实验表明,相同温度下,La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2合金的PCT曲线基本重合,且都具有优良的吸氢动力学性能;相比之下,后者的滞后系数要小于前者,吸氢量较大,吸氢速率也较快,故其储氢性能较优。300次吸放氢循环实验结果表明,La0.5Y0.5Ni4.8Al0.2合金的吸氢动力学性能虽然略有下降,但抗粉化性能较好。     

Dy0.6Tb0.3Pr0.1(Fe0.95Mn0.05)x取向晶体的结构与磁致伸缩

采用Ｃｚｏｃｈｒａｌｓｋｉ方法生长了Ｄｙ０．６Ｔｂ０．３Ｐｒ０．１（Ｆｅ０．９５Ｍｎ０．０５）ｘ（１．８５≤ｘ≤１．９５）取向合金。所有合金主相为立方Ｌａｖｅｓ相结构,择优取向不完整择优取向的方向与Ｘ的大小有关。研究了沿着这些样品的生长方向的磁致伸缩性能以及磁致伸缩性能与压力之间的关系。     

Thermal Stability of Amorphous Hydride Mg_(50)Ni_(50)H_(54) and Mg_(30)Ni_(70)H_(45)

The thermal stability of amorphous ternary hydrides Mg_(50)Ni_(50)H_(54) and Mg_(30)Ni_(70)H_(45) and their corre-sponding amorphous binary alloys Mg_(50)Ni_(50) and Mg_(30)Ni_(70) were studied with X-ray diffraction(XRD) and differential scanning calorimetry(DSC). Samples of the amorphous alloys were preparedby mechanical alloying and the amorphous hydrides were obtained by charging the alloys with gas-eous hydrogen at 3.0 MPa and 423 K. It was found that the amorphous hydrides released most oftheir hydrogen before the crystallization of the essentially hydrogen depleted amorphous alloy. Thecrystallization temperature of amorphous Mg_(50)Ni_(50)H_(54) elevated and that of amorphousMg_(30)Ni_(70)H_(45) did not change in relation to the original binary amorphous alloy. This is very excep-tional for amorphous hydrides. The reason for the effects of hydrogen absorption/desorption on thecrystallization of amorphous alloys was discussed.     

Zr65Al7.5Ni10Cu15Co2.5合金的玻璃转变温度

根据Ｚｒ６５Ａｌ７。５Ｎｉ１０Ｃｕ１５Ｃｏ２。５合金的纳米晶，晶体，液体和玻璃比热的测量结果，研究了合金的玻璃转变温度与全金的热力学函数，动力学参数以及加热速度的关系。结果表明，非晶态合金玻璃转变所需转变激活能很小，玻璃转变温度实际上是由于加热速度引起的不同状态的玻璃与液体的热力学平衡温度。     

Acousto-optic interaction in alpha-BaB(2)O(4)and Li(2)B(4)O(7) crystals

Experimental studies and analysis of acousto-optic diffraction in alpha-BaB(2)O(4) and Li(2)B(4)O(7) crystals are given. Ultrasonic wave velocity, elastic compliance and stiffness coefficients, and piezo-optic and photoelastic coefficients of alpha-BaB(2)O(4) and Li(2)B(4)O(7) crystals are determined. The acousto-optic figure of merit has been estimated for different possible geometries of acousto-optic interaction. It is shown that the acousto-optic figures of merit for alpha-BaB(2)O(4) crystals reach the value M(2)=(270 +/- 70) x 10(-15) s(3)/kg for the case of interaction with the slowest ultrasonic wave. The directions of propagation and polarization of those acoustic waves are obtained on the basis of construction of acoustic slowness surfaces. The acousto-optic diffraction is experimentally studied for alpha-BaB(2)O(4) and Li(2)B(4)O(7) crystals.     

Nanomechanical characterization of one-step combustion-synthesized Al(4)B(2)O(9) and Al(18)B(4)O(33) nanowires

Two kinds of aluminum borate nanowires, Al(4)B(2)O(9) and Al(18)B(4)O(33), were successfully synthesized by a one-step combustion method through control of the Al:B atomic ratio and synthesis temperature. Both nanowires are single crystalline but have distinguishing growth habits. Nanoindentation tests were performed directly on individual nanowires to reveal their mechanical properties. A 70% reduction in elastic modulus was found in Al(18)B(4)O(33) nanowires compared with their bulk counterpart. Al(18)B(4)O(33) nanowires exhibited higher hardness and elastic modulus than Al(4)B(2)O(9) nanowires.     

Natural Passivity of Amorphous Fe_(40)Ni_(40)P_(14)B_6 and Fe_(54.6)Ni_(38)Si_(4.1)B_(2.3)V_1 Alloys

The natural passive films forrned on Fe_(40)Ni_(40)P_(14)B_6 and Fe_(54.6)Ni_(38)Si_(4.1)B_(2.3)V_1 amorphous alloys long-term exposed in air have been studied by X-ray photoelectron spectroscopy (XPS) and Auger electron (including Ar+ ion depth profiling) spectroscopy (AES). The following aspects have been investigated: (1) chemical states of the elements in the films. binding energies and the chemical shifts measured by XPSf (2) structure and composition of the films fand (3) thickness of the passive films determined by AES depth profiling and XPS analysis.     

Plasma surface treatments of poly(l-lactic acid) (PLLA) and poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)

The surfaces of poly(l-lactic acid) (PLLA) and poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) were modified by oxygen and nitrogen plasma treatments. The physical and chemical surface characteristics were evaluated by contact angle tests, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The plasma treatments caused an increase in both contact angle and roughening, altered the surface morphology, inserted polar groups, and, consequently, enhanced the hydrophilicity for both PLLA and PHBV polymers.     

Work Functions of Pd_(83.5)Si_(16.5)and Cu_(70)Ti_(30)Glassy Alloys

The work functions before and aftercrystallization of two glassy alloys,Pd_(83.5)Si_(16.5) andCu_(70)Ti_(30) have been measured by means of the con-tact potential difference method in the secondaryelectron field at room temperature under 10~(-5) Pavacuum.The results show that the work functionsof both glassy alloys are higher than those of thecorresponding crystalline alloys.