GH706高温合金铣削力试验研究

针对高温合金材料GH706切削加工性差的问题,通过对高温合金GH706的铣削试验,研究切削速度、每齿进给量和轴向切削深度对铣削力的影响。通过单因素试验得到了切削参数与铣削力的变化曲线;用正交实验法和多元线性回归分析方法建立了铣削力经验公式,并进行了试验验证。试验结果表明,铣削力经验公式可以有效地预测铣削力的大小;铣削力随着轴向切深、每齿进给量的增加而增加,而随着切削速度的增加有减小的趋势。     

GH4169插铣参数对切削力的影响规律研究

为了优化高温合金GH4169插铣加工过程中的切削参数,采用正交试验法进行高温合金GH4169的铣削试验。基于试验法建立了切削力与切削参数之间的经验公式,分析了各切削参数对切削力的影响规律。运用方差分析法检验了经验公式的显著性。结果表明:F_x、F_y、F_z都随着切削速度V_c、每齿进给量f_z、径向切深a_e的增大而增大;三个方向的切削力受径向切深a_e的影响最大,其次是切削速度V_c,每齿进给量f_z的影响最小,且Z方向切削力F_z大于X、Y方向切削力F_x、F_y。     

高速铣削7050-T7451铝合金表面粗糙度研究

高速铣削广泛用于航空铝合金材料的加工,以7050-T7451铝合金材料为试验对象,运用正交试验方法分析研究了铣削该铝合金材料时,切削速度、切削深度、切削宽度和每齿进给量4个因素对表面粗糙度的影响规律,并通过多元非线性回归分析得出表面粗糙度的经验公式.研究结果表明:加工表面呈交叉织网状形貌,表面粗糙度随每齿进给量和铣削深度的增大而增大,随切削速度的增大而减小,切宽对铝合金表面粗糙度的影响不明显.铣削参数对表面粗糙度的影响显著性依次为:每齿进给量fz切削速度v轴向切削深度ap径向切削宽度ae.     

高温合金GH4169高速铣削仿真加工与分析

利用Third wave AdvantEdge FEM软件建立了三维切削模型,对高温合金GH4169进行了高速铣削模拟加工.通过模拟分析得到了切削速度、每齿进给量、切削深度对切削热的影响规律;试验中发现,切削速度的变化对切削温度的影响规律与高速切削理论有出入,切削速度的变化对切削温度的影响较每齿进给量和切削深度大.     

高速铣削加工钛合金Ti6Al4V的切削力和表面粗糙度试验

利用单因素实验法对高速铣削Ti6Al4V过程中各切削要素对切削力的影响进行分析,切削力随着切削速度的增加先增大后减小,随着每齿进给量和切削深度的增加而增大;利用正交试验法对高速铣削Ti6Al4V进行粗糙度分析,得出每齿进给量对工件表面粗糙度的影响最大,其次分别是切削速度、径向切深和轴向切深。     

切削用量对立铣加工钛合金Ti6Al4V切削力和切削温度影响规律的有限元仿真研究

利用软件AdvantEdge建立硬质合金涂层立铣刀三维铣削Ti6Al4V钛合金的有限元分析模型,模拟分析切削参数(切削速度、每齿进给量、轴向切削深度及径向切削深度)对刀具切削温度、切削力的影响规律.研究发现:切削力及切削温度随每齿进给量、轴向切削深度及径向切削深度的增加而增加:切削温度对切削深度的变化较敏感,随轴向切削深度和径向切削深度的增加显著增加;随着切削速度的增加,切削力先增大后减小,临界切削速度为120 m/min.     

切削参数对钛合金叶片铣削力的影响分析

进行钛合金叶片加工时,切削力易导致加工变形,影响加工精度和表面质量。因此利用UG软件建立钛合金叶片和切削刀具的三维模型,采用仿真软件建立铣削仿真模型,研究分析了切削参数的变化对铣削力产生的影响。对仿真所得铣削力进行极差分析,判断切削参数对铣削力的影响情况,并通过实际铣削加工试验对比仿真数据验证其准确性和可行性,基于此仿真模型对切削参数对轴向力的影响程度进行了单因素分析。研究结果表明：铣削钛合金叶片时,切削参数对切削力的影响程度从大到小依次为切削速度、背吃刀量和每齿进给量;切削速度与轴向力成反比,每齿进给量和背吃刀量与轴向力成正比。     

切削用量对高效铣削高强钢切削力的影响研究

在切削速度v=100～300m/min、每齿进给量f_z=0.01～0.1mm/z、轴向切削深度a_p=1～3mm条件下,对30CrNi2MoVA高强钢进行了高效铣削试验,研究了切削用量对切削力的影响。试验结果表明,切削速度对切削力的变化影响不大,随切削速度的增加径向力略有增加,切向力略有减小;轴向切削深度和进给量对切削力的变化影响较大,径向力和切向力均随轴向切削深度和进给量的增大而近似呈线性增大,且增幅较大;轴向力随切削用量的变化较小,且在不同切削用量下轴向力相差不大。在试验切削用量范围内,总体表现为径向力>切向力>轴向力。     

切削用量对立铣加工钛合金Ti6Al4V切削力和切削温度影响规律的有限元仿真研究

利用软件AdvantEdge建立硬质合金涂层立铣刀三维铣削Ti6Al4V钛合金的有限元分析模型,模拟分析切削参数(切削速度、每齿进给量、轴向切削深度及径向切削深度)对刀具切削温度、切削力的影响规律。研究发现:切削力及切削温度随每齿进给量、轴向切削深度及径向切削深度的增加而增加:切削温度对切削深度的变化较敏感,随轴向切削深度和径向切削深度的增加显著增加;随着切削速度的增加,切削力先增大后减小,临界切削速度为120m/min。     

密齿硬质合金涂层刀具铣削TC4钛合金试验研究

利用单因素试验方法进行了密齿硬质合金涂层刀具铣削TC4钛合金试验,研究每齿进给量和切削速度对切削力、切削温度、加工表面粗糙度以及切屑形态的影响。结果表明:切削方向分力F_x、刀轴方向分力F_z随每齿进给量的增大而增大,进给方向分力F_y随每齿进给量的增加变化不大;切削速度小于75m/min时切削力随切削速度的增加下降较为明显;切削速度超过75m/min时切削力变化不大;切削温度受每齿进给量影响较大,且影响程度随进给量的增加而逐渐减小;随着每齿进给量f_z的增大,加工表面粗糙度值先减小后增大;在每齿进给量高于0.04mm/z时,密齿铣刀铣削TC4钛合金得到的切屑为螺卷状,且随每齿进给量的增加,切屑的曲率半径减小,随切削速度的增大,螺卷状切屑的螺距减小。     

Minimal Realization of Linear Graph Models for Multi-physics Systems

An engineering system may consist of several different types of components,belonging to such physical"domains"as mechanical,electrical,fluid,and thermal.It is t...     

Quantum Cooperative Robotics and Autonomy

The intersection of Quantum Technologies and Robotics Autonomy is explored in the present paper.The two areas are brought together in establishing an interdisci...     

考虑进油孔有限长滑动轴承油膜力的近似解析解

针对具有进油孔的有限长滑动轴承油膜力求解问题,采用变分原理和分离变量法,求得了有限长滑动轴承油膜压力分布的近似解析表达式。将油膜压力分布的近似解析表达式在油膜存在区域上进行积分,即得到了油膜力。将提出的计算有限长滑动轴承油膜力方法与无限长轴承模型、有限元方法的计算结果进行了比较,发现了提出的方法与有限元方法的计算结果很接近。最后,研究了进油孔位置和进油压力对油膜存在区域、油膜力等的影响,研究结果表明进油孔位置和进油压力对油膜存在区域和油膜力有较大的影响。     

三绕组变压器的双绕组等效建模及在Matpower中的应用

针对实际电网存在着大量的三绕组变压器,但国际上一些著名商业软件,如BPA仿真软件、Matpower这一权威潮流计算开源软件,均只提供双绕组变压器模型,限制了其在具有三绕组变压器的电力系统中的应用的问题,潮流计算是自主开发的电力系统各种应用软件的核心模块,因此依托国际权威开源程序进行二次开发,是一种较好的选择。对Matpower要求的数据格式进行了归纳,对变压器的一般的等值电路及带理想变压器的等值电路和带标幺值的等值电路进行了分析研究,提出了三绕组变压器转换为双绕组等效模型的建模方法,使得原先只适应双绕组变压器的潮流计算软件可以适用于三绕组变压器电网的潮流计算;最后以Matpower软件为例进行了案例计算,并用PSASP仿真软件进行对比验证。研究结果证明,所提出的建模方法是有效的。     

On the Relation of Load to Average Gap in the Contact Between Surfaces with Longitudinal Roughness

A computer simulation model for the contact between longitudinally-oriented rough surfaces has been formulated. This model closely duplicates the actual surf ace contact deformation behavior by taking into account the elastic interactions between the asperities. There were no assumptions made about the shapes, or any deformation behavior of the asperities, except for their obeying the laws of elasticity. The plastic deformations on the high asperity peaks were taken into account by setting a ceiling on their contact pressures at the material hardness value. The simulations used real surface profiles which were digitized from unworn circumferentially ground steel surfaces. Each pair of these profiles was mathematically combined to form an equivalent rough profile pressing against an infinitely rigid flat and having the appropriately adjusted elastic modulus. A total of 28 different pairs of profiles were used in the simulations. Each contacting pair was subjected to 30 different load levels and the local contact pressures and deformations were calculated. The contact simulations yielded some important mathematical relationships between parameters, such as the real area of contact, average gap, and average asperity load through statistical curve fitting. Two analytical functions were generated to relate the average load to average gap and the real area of contact to load.     

Fifth International Summer School on Screw-Theory Based Methods in Robotics

正3-11 September,2014University of Bologna,Bologna,Italy www.summerscrews.org summerscrews2014.ing.unibo.it SUMMER 20SCREWS 14In 2014,our screw-theory school comes to the world's oldest university.In early September,Summer Screws'14 will gather six experts in the application of screw theory in robotics and up to 40 participants at the University of Bologna,Bologna,Italy.The school will teach attendees how to apply existing methods and empower them to develop new ones in their own research.The basic theoretical notions will be introduced in a rigorous manner,emphasizing examples,applications,and exercises.Scholarships are available.     

INTEGRAL EQUATION METHOD＇S APPLICATION IN HOLE-EDGE STRESS OF COMPOSITE MATERIAL PLATE WITH DIFFERENT SHAPED HOLES

The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to the structure. So the hole-edge stress concentration is always a serious phenomenon. And the phenomenon makes the structure strength decrease very quickly to form dangerous weak points. Most partial damage begins from these weak points. According to the complex variable functions theory, the accurate boundary condition of composite plate with different hole-shapes is founded by conformal mapping method to settle the boundary condition problem of complex hole-shapes. Composite plate with commonly hole-shapes in engineering is studied by several complex variable stress fimction. The boundary integral equations are founded based on exact boundary conditions. Then the exact hole-edge stress analytic solution of composite plate with rectangle holes and wing manholes is resolved. Both of offset axis loadings and its influences on the stress concentration coefficient of the hole-edge are discussed. And comparisons of different loads along various offset axis on the hole-edge stress distribution of orthotropic plate with rectangle hole or wing manhole are made. It can be concluded that hole-edge with continuous variable curvatures might help to decrease the stress concentration coefficient; and smaller angle of outer load and fiber can decrease the stress peak value.     

INDUSTRIAL ENGINEERING AND VISUALISATION-A PRODUCT DEVELOPMENT PERSPECTIVE

Taking the actual project of teaching and researching process for example, the relationship between the industrial engineering and product development is discussed. And use the novel visualization technology to support the industrial engineering and product development. How to use the new computer modeling and simulating technologies to support the product development and industrial engineering, is introduced especially. The support includes both domestic products and industrial systems. The visualization and computer technologies take a very important role in some system or multi-direction modeling, those technologies mentioned above can help the industrial engineers study the effect of design on the whole life circle, including the producing steps. So the engineers can avoid making the wrong decision which may cause bad effects on the whole industrial engineering.     

电站锅炉模糊风险评价方法研究与应用

针对电站锅炉风险等级评价问题,将模糊综合评价技术应用到电站锅炉风险等级评价中。开展了电站锅炉失效影响因素及模糊评价因素的重要程度分析,建立了一套科学合理适于在线评价的电站锅炉风险评价体系,提出了模糊综合评价技术与改进的模糊层次分析法相结合的模糊风险评价方法,利用改进的模糊层次分析法计算了指标体系中各层指标权重。对某一台电站锅炉的实际运行工况影响子因素进行了模糊风险评价,采用模糊合成算子进行模糊综合运算得到电了站锅炉运行工况影响子因素的评价向量。研究结果表明:电站锅炉的运行工况影响子因素的风险评价等级为第6级,失效可能性等级为小,该电站锅炉运行工况良好。     

Short-Term Relay Quality Prediction Algorithm Based on Long and Short-Term Memory

The fraction defective of semi-finished products is predicted to optimize the process of relay production lines, by which production quality and productivity ar...