A time-interleaved continuous-time /spl Delta//spl Sigma/ modulator with 20-MHz signal bandwidth

This paper presents the first implementation results for a time-interleaved continuous-time /spl Delta//spl Sigma/ modulator. The derivation of the time-interleaved continuous-time /spl Delta//spl Sigma/ modulator from a discrete-time /spl Delta//spl Sigma/ modulator is presented. With various simplifications, the resulting modulator has only a single path of integrators, making it robust to DC offsets. A time-interleaved by 2 continuous-time third-order low-pass /spl Delta//spl Sigma/ modulator is designed in a 0.18-/spl mu/m CMOS technology with an oversampling ratio of 5 at sampling frequencies of 100 and 200 MHz. Experimental results show that a signal-to-noise-plus-distortion ratio (SNDR) of 57 dB and a dynamic range of 60 dB are obtained with an input bandwidth of 10 MHz, and an SNDR of 49 dB with a dynamic range of 55 dB is attained with an input bandwidth of 20 MHz. The power consumption is 101 and 103 mW, respectively.     

Self-tuning algorithms for high-performance bandpass switched-capacitor /spl Sigma//spl Delta/ modulators

Switched-capacitor high-frequency bandpass /spl Sigma//spl Delta/ modulators could suffer from capacitor mismatch, finite opamp dc gain, and finite opamp bandwidth. These problems make the notch frequency and the quality factor of the zeros of the noise transfer function to deviate from their nominal values, strongly affecting the modulator dynamic range (DR). In order to avoid this situation, two sampled-data algorithms have been developed which allow to self-calibrate the bandpass /spl Sigma//spl Delta/ modulators. They use 3500 gate and 0.043 mm/sup 2/ area and consume power only when they are active, while, when the system is on, they are off and do not interfere with standard operation. The validity of the proposal is demonstrated by a silicon prototype in which the proposed solution allows to guarantee a 75-dB DR performance also under worst case conditions. In the particular case, it allows for the recovery of 3 dB in the SNR for the 200-kHz FM band (from 73 to 76 dB).     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

A 0.7-V MOSFET-only switched-opamp /spl Sigma//spl Delta/ modulator in standard digital CMOS technology

A 0.7-V MOSFET-only /spl Sigma//spl Delta/ modulator for voice band applications is presented. The second-order modulator is realized using a switched-opamp technique. All capacitors are realized using compensated MOS devices operated in the depletion region. A combination of parallel and series compensated depletion-mode MOSCAPs is used to obtain high area efficiency. The circuit is fabricated in a 0.18-/spl mu/m CMOS process. The only components used are standard n-MOS and p-MOS transistors with threshold voltages of approximately 400 mV. All transistors are operated within the supply voltage window of 0.7 V; voltage boosting techniques are not used. The active area is 0.082 mm/sup 2/. The modulator achieves 67-dB signal-to-noise-and-distortion ratio, 70-dB signal-to-noise ratio, and 75-dB dynamic range at 8-kHz signal bandwidth and consumes 80 /spl mu/W of power.     

A 14-bit delta-sigma ADC with 8/spl times/ OSR and 4-MHz conversion bandwidth in a 0.18-/spl mu/m CMOS process

A 14-bit 8/spl times/ oversampling delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter (ADC) for wide-band communication applications has been developed. By using a novel architecture, a high maximum out-of-band quantization noise gain (Q/sub max/) is realized, which greatly improves the SNR and tonal behavior. The ADC employs a fifth-order single-stage structure with a 4-bit quantizer. It achieves 82-dB SNDR and 103-dB SFDR at 4-MHz conversion bandwidth with a single 1.8-V power supply.     

Highly linear 2.5-V CMOS /spl Sigma//spl Delta/ modulator for ADSL+

We present a 90-dB spurious-free dynamic range sigma-delta modulator (/spl Sigma//spl Delta/M) for asymmetric digital subscriber line applications (both ADSL and ADSL+), with up to a 4.4-MS/s digital output rate. It uses a cascade (MASH) multibit architecture and has been implemented in a 2.5-V supply, 0.25-/spl mu/m CMOS process with metal-insulator-metal capacitors. The prototypes feature 78-dB dynamic range (DR) in the 30-kHz to 2.2-MHz band (ADSL+) and 85-dB DR in the 30-kHz to 1.1-MHz band (ADSL). Integral and differential nonlinearity are within /spl plusmn/0.85 and /spl plusmn/0.80 LSB/sub 14 b/, respectively. The /spl Sigma//spl Delta/ modulator and its auxiliary blocks (clock phase and reference voltage generators, and I/O buffers) dissipate 65.8 mW. Only 55 mW are dissipated in the /spl Sigma//spl Delta/ modulator.     

A 2.2-mW CMOS bandpass continuous-time multibit /spl Delta/-/spl Sigma/ ADC with 68 dB of dynamic range and 1-MHz bandwidth for wireless applications

A delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter featuring 68-dB dynamic range and 64-dB signal-to-noise ratio in a 1-MHz bandwidth centered at an intermediate frequency of 2 MHz with a 48-MHz sample rate is reported. A second-order continuous-time modulator employing 4-bit quantization is used to achieve this performance with 2.2 mW of power consumption from a 1.8-V supply. The modulator including references occupies 0.36 mm/sup 2/ of die area and is implemented in a 0.18-/spl mu/m five-metal single-poly digital CMOS process.     

A 2-GHz analog-to-digital delta-sigma modulator for CDMA receivers with 79-dB signal-to-noise ratio in 1.23-MHz bandwidth

This paper presents the design of a second-order single-bit analog-to-digital continuous-time delta-sigma modulator (CT-/spl Delta//spl Sigma/M) that can be used in wireless CDMA receivers. The CT-/spl Delta//spl Sigma/M samples at 2 GHz, consumes 18 mW at 1.8 V and has a 79-dB signal-to-noise ratio (SNR) over a 1.23-MHz bandwidth. The CT-/spl Delta//spl Sigma/M was fabricated in a 0.18-/spl mu/m 1-poly 6-metal, CMOS technology and has an active area of approximately 0.892 mm/sup 2/. The /spl Delta//spl Sigma/M's critical performance specifications are derived from the CDMA receiver specifications.     

A third-order /spl Sigma//spl Delta/ modulator in 0.18-/spl mu/m CMOS with calibrated mixed-mode integrators

This paper describes a third-order sigma-delta (/spl Sigma//spl Delta/) modulator that is designed and implemented in 0.18-/spl mu/m CMOS process. In order to increase the dynamic range, this modulator takes advantage of mixed-mode integrators that consist of analog and digital integrators. A calibration technique is applied to the digital integrator to mitigate mismatch between analog and digital paths. It is shown that the presented modulator architecture can achieve a 12-dB better dynamic range than conventional structures with the same oversampling ratio (OSR). The experimental prototype chip achieves a 76-dB dynamic range for a 200-kHz signal bandwidth and a 55-dB dynamic range for a 5-MHz signal bandwidth. It dissipates 4 mW from 1.8-V supply voltages and occupies 0.7-mm/sup 2/ silicon area.     

Tunable continuous-time bandpass /spl Sigma//spl Delta/ modulators with fractional delays

An analytical design methodology for continuous-time (CT) bandpass (BP) /spl Sigma//spl Delta/ modulators is presented. Second- and fourth-order tunable continuous time BP /spl Sigma//spl Delta/ modulator design equations are presented. A novel /spl Sigma//spl Delta/ loop architecture, where the traditional CT BP loop filter function is replaced with the filter function with fractional delays, is proposed. Validity of the methodology is confirmed by mixed-signal behavioral simulations.     

80-MHz bandpass /spl Delta//spl Sigma/ modulators for multimode digital IF receivers

Three fully differential bandpass (BP) /spl Delta//spl Sigma/ modulators are presented. Two double-delay resonators are implemented using only one operational amplifier. The prototype circuits operate at a sampling frequency of 80 MHz. The BP /spl Delta//spl Sigma/ modulators can be used in an intermediate-frequency (IF) receiver to combine frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an IF of 60 MHz to a digital IF of 20 MHz. The measured peak signal-to-noise-plus-distortion ratios are 78 dB for 270 kHz (GSM), 75 dB for 1.25 MHz (IS-95), 69 dB for 1.762 MHz (DECT), and 48 dB for 3.84 MHz (WCDMA/CDMA2000) bandwidths. The circuits are implemented with a 0.35-/spl mu/m CMOS technology and consume 24-38 mW from a 3.0-V supply, depending on the architecture.     

A continuous-time /spl Sigma//spl Delta/ ADC with increased immunity to interferers

Receivers are being digitized in a quest for flexibility. Analog filters and programmable gain stages are being exchanged for digital processing at the price of a very challenging ADC. This paper presents an alternative solution where the filter and programmable gain functionality is integrated into a /spl Sigma//spl Delta/ ADC. The novel filtering ADC is realized by adding a high-pass feedback path to a conventional /spl Sigma//spl Delta/ ADC while a compensating low-pass filter in the forward path maintains stability. As such, the ADC becomes highly immune to interferers even if they exceed the maximum allowable input level for the wanted channel. As a consequence, the ADC input range can be programmed dynamically to the level of the wanted signal only. This results in an input-referred dynamic range of 89 dB in 1-MHz bandwidth and an intentionally moderate output signal-to-noise-and-distortion ratio of 46-59 dB (depending on the programmed gain). The merged functionality enables a better overall power/performance balance for the receiver baseband. The design consumes less than 2 mW and active area is 0.14 mm/sup 2/ in a 0.18-/spl mu/m digital CMOS technology.     

A continuous-time sigma-delta modulator with 88-dB dynamic range and 1.1-MHz signal bandwidth

This paper presents the design and experimental results of a continuous-time /spl Sigma//spl Delta/ modulator for ADSL applications. Multibit nonreturn-to-zero (NRZ) DAC pulse shaping is used to reduce clock jitter sensitivity. The nonzero excess loop delay problem in conventional continuous-time /spl Sigma//spl Delta/ modulators is solved by our proposed architecture. A prototype third-order continuous-time /spl Sigma//spl Delta/ modulator with 5-bit internal quantization was realized in a 0.5-/spl mu/m double-poly triple-metal CMOS technology, with a chip area of 2.4 /spl times/ 2.4 mm/sup 2/. Experimental results show that the modulator achieves 88-dB dynamic range, 84-dB SNR, and 83-dB SNDR over a 1.1-MHz signal bandwidth with an oversampling ratio of 16, while dissipating 62 mW from a 3.3-V supply.     

A vertically integrated tool for automated design of /spl Sigma//spl Delta/ modulators

We present a tool that starting from high-level specifications of switched-capacitor (SC) /spl Sigma//spl Delta/ modulators calculates optimum specifications for their building blocks and then optimum sizes for the block schematics. At both design levels, optimization is performed using statistical techniques to enable global design and innovative heuristics for increased computer efficiency as compared with conventional statistical optimization. The tool uses an equation-based approach at the modulator level, a simulation-based approach at the cell level, and incorporates an advanced /spl Sigma//spl Delta/ behavioral simulator for monitoring and design space exploration. We include measurements taken from two silicon prototypes: (1) a 16 b @ 16 kHz output rate second-order /spl Sigma//spl Delta/ modulator; and (2) a 17 b @ 40 kHz output rate fourth-order /spl Sigma//spl Delta/ modulator. Both use SC fully differential circuits and were designed using the proposed tool and manufactured in a 1.2 /spl mu/m CMOS double-metal double-poly technology.<>     

Integrated stereo /spl Delta//spl Sigma/ class D amplifier

A 2/spl times/40 W class D amplifier chip is realized in 0.6-/spl mu/m BCDMOS technology, integrating two delta-sigma (/spl Delta//spl Sigma/) modulators and two full H-bridge switching output stages. Analog feedback from H-bridge outputs helps achieve 67-dB power supply rejection ratio, 0.001% total harmonic distortion, and 104-dB dynamic range. The modulator clock rate is 6 MHz, but dynamically adjusted quantizer hysteresis reduces output data rate to 450 kHz, helping achieve 88% power efficiency. At AM radio frequencies, the modulator output spectrum contains a single peak, but is otherwise tone-free, unlike conventional pulse-width modulation (PWM) modulators which contain energetic tones at harmonics of the PWM clock frequency.     

A 14-bit high-temperature /spl Sigma//spl Delta/ modulator in standard CMOS

Experimental verification is given for the use of /spl Sigma//spl Delta/ modulation for high-temperature applications (/spl ges/approximately 150/spl deg/C) in a standard CMOS process. Switched-capacitor circuits are used to implement a second-order single-stage and a third-order 2-1 MASH /spl Sigma//spl Delta/ modulator with single-bit quantization. The two modulators have an oversampling ratio of 256 with an input signal bandwidth of 500 Hz. The modulators were fabricated in a 1.5-/spl mu/m standard CMOS technology. A fully differential signal path and near minimum sized switches are used to mitigate the effect of large junction-to-substrate leakage current present at high temperatures. Experimental results show both modulators are capable of over 14 bits of resolution at 225/spl deg/C and over 13 bits of resolution at 255/spl deg/C. Results show that the single-stage modulator is more resistant to high-temperature circuit impairment than is the MASH cascaded structure.     

Adaptive order reduction scheme for high-order single-bit /spl Delta//spl Sigma/ Modulators

A scheme for achieving adaptive reduction in the order of the loop filter of usual high-order, single-stage, single-bit Delta-Sigma (/spl Delta//spl Sigma/) modulators is proposed in order to improve their performance. The resulting /spl Delta//spl Sigma/ modulators can recover from instability effectively, having also an extended input signal range in comparison to that of the corresponding conventional /spl Delta//spl Sigma/ modulators.     

A 3.3-mW /spl Sigma//spl Delta/ modulator for UMTS in 0.18-/spl mu/m CMOS with 70-dB dynamic range in 2-MHz bandwidth

A quadrature fourth-order, continuous-time, /spl Sigma//spl Delta/ modulator with 1.5-b quantizer and feedback digital-to-analog converter (DAC) for a universal mobile telecommunication system (UMTS) receiver chain is presented. It achieves a dynamic range of 70 dB in a 2-MHz bandwidth and the total harmonic distortion is -74 dB at full-scale input. When used in an integrated receiver for UMTS, the dynamic range of the modulator substantially reduces the need for analog automatic gain control and its tolerance of large out-of-band interference also permits the use of only first-order prefiltering. An IC including an I and Q /spl Sigma//spl Delta/ modulator, phase-locked loop, oscillator, and bandgap dissipates 11.5 mW at 1.8 V. The active area is 0.41 mm/sup 2/ in a 0.18-/spl mu/m 1-poly 5-metal CMOS technology.     

A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.