Nationwide indoor 222Rn and 220Rn map for India: a review

Considering the role of radon in epidemiology, an attempt was made to make a nation-wide map of indoor ²²²Rn and ²²⁰Rn for India. More than 5000 measurements have been carried out in 1500 dwellings across the country comprising urban and nonurban locations. The solid state nuclear track detectors based twin cup ²²²Rn/²²⁰Rn discrimination dosimeters were deployed for the measurement of indoor ²²²Rn, ²²⁰Rn and their progeny levels. The geometric means of estimated annual inhalation dose rate due to indoor ²²²Rn, ²²⁰Rn and their progeny in the dwellings was 0.94 mSvy⁻¹ (geometric standard deviation 2.5). It was observed that the major contribution to the indoor inhalation dose was due to indoor ²²²Rn and its progeny. However, the contribution due to indoor ²²⁰Rn and its progeny was not trivial as it was found to be about 20% of the total indoor inhalation dose rates. The indoor ²²²Rn levels in dwellings was significantly different depending on the nature of walls and floorings.     

Pre-concentration of naturally occurring radionuclides and the determination of (212)Pb from fresh waters

A novel technique has been developed for determining the ²¹²Pb activity of fresh waters. This is of interest to environmental monitoring programmes that utilise gross α-activity methods to screen for anthropogenic radionuclides. The contribution from ²¹²Pb varies, and is difficult to experimentally measure due to its relatively short half-life (t_½ = 10.6 h) and low environmental activity (<0.1 Bq l⁻¹). The use of a three-stage technique that encompasses a unique form of pre-concentration, separation and analysis by liquid scintillation counting allows a lower detection limit of 0.006 Bq l⁻¹ with a chemical yield of 92.5 ± 5.6%. The measurement can be obtained within 7 h of sample collection, and is calculated using the radioactive decay of ²¹²Bi. Other naturally occurring radionuclides may also be extracted using the pre-concentration stage of the technique, with efficiencies above 90% at a range of pH values.     

Dose estimation and radon action level problems due to nanosize radon progeny aerosols in underground manganese ore mine

One of the essential parameters influencing of the dose conversion factor is the ratio of unattached short-lived radon progeny. This may differ from the value identified for indoor conditions when considering special workplaces such as mines. Inevitably, application of the dose conversion factors used in surface workplaces considerably reduces the reliability of dose estimation in the case of mines.This paper surveyed the concentration of radon and its short-lived radon progeny and identified the unattached fraction of short-lived radon progeny. As well equilibrium factor during the month of August was calculated simultaneously at two extraction faces in a manganese ore mine.During working hours the average radon concentrations were 220 Bq m⁻³ and 530 Bq m⁻³ at Faces 1 and 2; the average short-lived progeny concentration was 90 Bq m⁻³ and 190 Bq m⁻³, the average equilibrium factors were 0.46 and 0.36, and the average unattached fractions were 0.21 and 0.17, respectively. The calculated dose conversion factor was between 9 and 27 mSv WLM⁻¹, but higher values could also be possible.     

External gamma-ray dose rate and radon concentration in indoor environments covered with Brazilian granites

Health hazard from natural radioactivity in Brazilian granites, covering the walls and floor in a typical dwelling room, was assessed by indirect methods to predict external gamma-ray dose rates and radon concentrations. The gamma-ray dose rate was estimated by a Monte Carlo simulation method and validated by in-situ measurements with a NaI spectrometer. Activity concentrations of ²³²Th, ²²⁶Ra, and ⁴⁰K in an extensive selection of Brazilian commercial granite samples measured by using gamma-ray spectrometry were found to be 4.5-450 Bq kg⁻¹, 4.9-160 Bq kg⁻¹ and 190-2029 Bq kg⁻¹, respectively. The maximum external gamma-ray dose rate from floor and walls covered with the Brazilian granites in the typical dwelling room (5.0 m × 4.0 m area, 2.8 m height) was found to be 120 nGy h⁻¹, which is comparable with the average worldwide exposure to external terrestrial radiation of 80 nGy h⁻¹ due to natural sources, proposed by United Nations Scientific Committee on the Effects of Atomic Radiation. Radon concentrations in the room were also estimated by a simple mass balance equation and exhalation rates calculated from the measured values of ²²⁶Ra concentrations and the material properties. The results showed that the radon concentration in the room ventilated adequately (0.5 h⁻¹) will be lower than 100 Bq m⁻³, value recommended as a reference level by the World Health Organization.     

Radon exhalation from building materials for decorative use

Long-term exposure to radon increases the risk of developing lung cancer. There is considerable public concern about radon exhalation from building materials and the contribution to indoor radon levels. To address this concern, radon exhalation rates were determined for 53 different samples of drywall, tile and granite available on the Canadian market for interior home decoration. The radon exhalation rates ranged from non-detectable to 312 Bq m⁻² d⁻¹. Slate tiles and granite slabs had relatively higher radon exhalation rates than other decorative materials, such as ceramic or porcelain tiles. The average radon exhalation rates were 30 Bq m⁻² d⁻¹ for slate tiles and 42 Bq m⁻² d⁻¹ for granite slabs of various types and origins. Analysis showed that even if an entire floor was covered with a material having a radon exhalation rate of 300 Bq m⁻² d⁻¹, it would contribute only 18 Bq m⁻³ to a tightly sealed house with an air exchange rate of 0.3 per hour. Generally speaking, building materials used in home decoration make no significant contribution to indoor radon for a house with adequate air exchange.     

A theoretical approach to indoor radon and thoron distribution

A model based on the Finite Element Method was developed to simulate indoor behavior of radon ((222)Rn), thoron ((220)Rn) and their progeny, as well as, to calculate their spatial distributions. Since complex physical processes govern the distribution several simplifications were made in the presented model. Different locations of possible radon/thoron sources, diffusion of these gases, their radioactive decay, etc were taken into account. Influences of different parameters on thoron/radon as well as indoor distribution of their progeny, such as the geometry and room dimension, the presence of aerosols and their size distribution expressed through the diffusion coefficient, different kinds of ventilation, etc, were investigated. It has been found that radon is distributed homogeneously, while the thoron concentration is rather inhomogeneous and decreases exponentially with the distance from the source. Regardless of the source distribution, the distribution of radon was homogeneous, except at places near an air inlet and outlet. However, the distribution of thoron depends on the source distribution. If thoron emanates from walls or the floor, its concentration decreases with the distance from the wall. Moreover, the concentration gradient is much larger near walls. This suggests that the actual selection of the site effect should be taken into account when obtaining a representative value of indoor (220)Rn and their progeny for dose assessment. The simulation results of activities and their distribution were in accordance with the results of other studies and experiments.     

Distribution of radionuclides in the guano sediments of Xisha Islands, South China Sea and its implication

Several natural and anthropogenic radionuclides (²¹⁰Pb, ²²⁶Ra and ¹³⁷Cs) in guano-phosphatic coral sediments and pure guano particles collected from Ganquan, Guangjin, Jinqing and Jinyin Islands of the Xisha archipelago, South China Sea, were analyzed. The Constant Initial Concentration (CIC) model and the Constant Rate of Supply (CRS) model were applied for age calculation. The average supply rate of ²¹⁰Pb was 126 Bq m⁻² a⁻¹, very close to the flux of northern hemisphere average (125 Bq m⁻² a⁻¹). The activities of anthropogenic radionuclides in the sediments were very low, indicating that human nuclear tests did not notably impact this region. The main source of radionuclides in the sediments was from atmospheric precipitation, and the organic matter derived from plant and produced by nutrient-rich guano could further enhance them.     

Seasonal and inter-annual variation of Beryllium-7 deposition in birch-tree leaves and grass in the northeast upland area of the Czech Republic

The activity concentrations of Beryllium-7 (⁷Be), a naturally occurring radioisotope produced in the atmosphere, were measured in leaves of birch-trees, above-ground parts of grass, soil and rainwater in the mountain massive Kralicky Sneznik (the northeast of the Czech Republic, altitude about 750 m) in the years of 2005, 2006 and 2007. Dried and ground samples of the plants and soils, and water samples from wet deposition were used to determine the ⁷Be content using a semiconductor gamma spectrometer. The ⁷Be values ranged from 147.0 to 279.6 Bq kg⁻¹, from 48.7 to 740.8 Bq kg⁻¹, from 2.1 to 8.7 Bq kg⁻¹, and from 0.6 to 1.9 Bq kg⁻¹ in birch-tree leaves, grass samples, soils, and rainwater, respectively. Insignificant inter-annual variations but significant increase in the ⁷Be activity concentrations during the spring and summer months were observed in birch-tree leaves and grass samples. The seasonal variation of the ⁷Be concentrations in grass samples correlated (R² = 0.4663 and 0.6489) with precipitation. No similar correlation was found for ⁷Be in birch-tree leaves. Beryllium-7 content in birch-tree leaves and in aerial parts of grass was mainly caused by direct transport of ⁷Be from wet deposition into aerial parts of the observed plants.     

Short-term seasonal variability in Be wet deposition in a semiarid ecosystem of central Argentina

The ⁷Be wet deposition has been intensively investigated in a semiarid region at San Luis Province, Argentina. From November 2006 to May 2008, the ⁷Be content in rainwater was determined in 58 individual rain events, randomly comprising more than 50% of all individual precipitations at the sampling period. ⁷Be activity concentration in rainwater ranged from 0.7 ± 0.3 Bq l⁻¹ to 3.2 ± 0.7 Bq l⁻¹, with a mean value of 1.7 Bq l⁻¹ (sd = 0.53 Bq l⁻¹). No relationship was found between ⁷Be content in rainwater and (a) rainfall amount, (b) precipitation intensity and (c) elapsed time between events. ⁷Be ground deposition was found to be well correlated with rainfall amount (R = 0.92). For the precipitation events considered, the ⁷Be depositional fluxes ranged from 1.1 to 120 Bq m⁻², with a mean value of 32.7 Bq m⁻² (sd = 29.9 Bq m⁻²). The annual depositional flux was estimated at 1140 ± 120 Bq m⁻² y⁻¹. Assuming the same monthly deposition pattern and that the ⁷Be content in soil decreases only through radioactive decay, the seasonal variation of ⁷Be areal activity density in soil was estimated. Results of this investigation may contribute to a valuable characterization of ⁷Be input in the explored semiarid ecosystem and its potential use as tracer of environmental processes.     

Polonium-210 and lead-210 in the terrestrial environment: a historical review

The radionuclides ²¹⁰Po and ²¹⁰Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of ²³⁸U in the earth’s crust. Their presence in the atmosphere is due to the decay of ²²²Rn diffusing from the ground. The range of activity concentrations in ground level air for ²¹⁰Po is 0.03-0.3 Bq m⁻³ and for ²¹⁰Pb 0.2-1.5 Bq m⁻³.In drinking water from private wells the activity concentration of ²¹⁰Po is in the order of 7-48 mBq l⁻¹ and for ²¹⁰Pb around 11-40 mBq l⁻¹. From water works, however, the activity concentration for both ²¹⁰Po and ²¹⁰Pb is only in the order of 3 mBq l⁻¹.Mosses, lichens and peat have a high efficiency in capturing ²¹⁰Po and ²¹⁰Pb from atmospheric fallout and exhibit an inventory of both ²¹⁰Po and ²¹⁰Pb in the order of 0.5-5 kBq m⁻² in mosses and in lichens around 0.6 kBq m⁻². The activity concentrations in lichens lies around 250 Bq kg⁻¹, dry mass.Reindeer and caribou graze lichen which results in an activity concentration of ²¹⁰Po and ²¹⁰Pb of about 1-15 Bq kg⁻¹ in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of ²¹⁰Po and ²¹⁰Pb in humans. The effective annual dose due to ²¹⁰Po and ²¹⁰Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a⁻¹ respectively.In soils, ²¹⁰Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of ²¹⁰Po in various soils are in the range of 20-240 Bq kg⁻¹.Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of ²¹⁰Po is particularly high as the result of the direct deposition of ²²²Rn daughters from atmospheric deposition. Tobacco is a terrestrial product with high activity concentrations of ²¹⁰Po and ²¹⁰Pb. The overall average activity concentration of ²¹⁰Po is 13 ± 2 Bq kg⁻¹. It is rather constant over time and by geographical origin.The average median daily dietary intakes of ²¹⁰Po and ²¹⁰Pb for the adult world population was estimated to 160 mBq day⁻¹ and 110 mBq day⁻¹, corresponding to annual effective doses of 70 μSv a⁻¹ and 28 μSv a⁻¹, respectively. The dietary intakes of ²¹⁰Po and ²¹⁰Pb from vegetarian food was estimated to only 70 mBq day⁻¹ and 40 mBq day⁻¹ corresponding to annual effective doses of 30.6 μSv a⁻¹ and 10 μSv a⁻¹, respectively. Since the activity concentration of ²¹⁰Po and ²¹⁰Pb in seafood is significantly higher than in vegetarian food the effective dose to populations consuming a lot of seafood might be 5-15 fold higher.     

Contribution of (222)Rn-bearing water to indoor radon and indoor air quality assessment in hot spring hotels of Guangdong, China

This study investigates the contribution of radon (²²²Rn)-bearing water to indoor ²²²Rn in thermal baths. The ²²²Rn concentrations in air were monitored in the bathroom and the bedroom. Particulate matter (PM, both PM₁₀ and PM_2.5) and carbon dioxide (CO₂) were also monitored with portable analyzers. The bathrooms were supplied with hot spring water containing 66-260 kBq m⁻³ of ²²²Rn. The results show that the spray of hot spring water from the bath spouts is the dominant mechanism by which ²²²Rn is released into the air of the bathroom, and then it diffuses into the bedroom. Average ²²²Rn level was 110-410% higher in the bedrooms and 510-1200% higher in the bathrooms compared to the corresponding average levels when there was no use of hot spring water. The indoor ²²²Rn levels were influenced by the ²²²Rn concentrations in the hot spring water and the bathing times. The average ²²²Rn transfer coefficients from water to air were 6.2 × 10⁻⁴-4.1 × 10⁻³. The 24-h average levels of CO₂ and PM₁₀ in the hotel rooms were 89% and 22% higher than the present Indoor Air Quality (IAQ) standard of China. The main particle pollutant in the hotel rooms was PM_2.5. Radon and PM₁₀ levels in some hotel rooms were at much higher concentrations than guideline levels, and thus the potential health risks to tourists and especially to the hotel workers should be of great concern, and measures should be taken to lower inhalation exposure to these air pollutants.     

Indoor radon levels in Greek schools

Radon and gamma dose rate measurements were performed in 512 schools in 8 of the 13 regions of Greece. The distribution of radon concentration was well described by a lognormal distribution. Most (86%) of the radon concentrations were between 60 and 250 Bq m⁻³ with a most probable value of 135 Bq m⁻³. The arithmetic and geometric means of the radon concentration are 149 Bq m⁻³ and 126 Bq m⁻³ respectively. The maximum measured radon gas concentration was 958 Bq m⁻³. As expected, no correlation between radon gas concentration and indoor gamma dose rate was observed. However, if only mean values for each region are considered, a linear correlation between radon gas concentration and gamma dose rate is apparent. Despite the fact that the results of radon concentration in schools cannot be applied directly for the estimation of radon concentration in homes, the results of the present survey indicate that it is desirable to perform an extended survey of indoor radon in homes for at least one region in Northern Greece.     

Relationship between deposition and attachment rates in Jacobi room model

It is shown in this work that parameters of the Jacobi model, which describes behavior of short-lived radon progeny, are not independent. The relationship between deposition rate of attached radon progeny and attachment rate of their unattached fraction was determined in this paper. It was found that deposition rate increases when the attachment rate is smaller; this effect is more pronounced for larger friction velocity. The deposition rate of attached radon progeny is presented here as a function of friction velocity, ventilation and attachment rate. Deposition rate of attached fraction was estimated in the range 0.012-0.46 h⁻¹, when attachment rate varies from 10 h⁻¹ to 100 h⁻¹.     

Development of an energy discriminate CR-39(®) nuclear track etch dosimeter for Radon-220 gas measurements

An energy discriminate CR-39^® nuclear track etch dosimeter for use in a ²²⁰Rn and ²²²Rn gas monitor has been developed and experimentally assessed. It utilises a thin film of Mylar^® C to attenuate the alpha particle energies to allow only the damage tracks created by the 8.785 MeV alpha particles emitted from ²¹²Po of the ²³²Th decay chain to be registered in the CR-39^® plaque, allowing for the direct measurement of ²²⁰Rn gas concentrations. The dosimeter was developed through a combination of experimental investigations and theoretical simulations using the Monte Carlo ion transport modelling program Stopping and Range of Ions in Materials (SRIM 2008). A film thickness of 54 μm has been shown to attenuate all alpha energies less then 7.7 MeV.     

Spatiotemporal variation of radon and carbon dioxide concentrations in an underground quarry: coupled processes of natural ventilation, barometric pumping and internal mixing

Radon-222 and carbon dioxide concentrations have been measured during several years at several points in the atmosphere of an underground limestone quarry located at a depth of 18 m in Vincennes, near Paris, France. Both concentrations showed a seasonal cycle. Radon concentration varied from 1200 to 2000 Bq m⁻³ in summer to about 800-1400 Bq m⁻³ in winter, indicating winter ventilation rates varying from 0.6 to 2.5 × 10⁻⁶ s⁻¹. Carbon dioxide concentration varied from 0.9 to 1.0% in summer, to about 0.1-0.3% in winter. Radon concentration can be corrected for natural ventilation using temperature measurements. The obtained model also accounts for the measured seasonal variation of carbon dioxide. After correction, radon concentrations still exhibit significant temporal variation, mostly associated with the variation of atmospheric pressure, with coupling coefficients varying from −7 to −26 Bq m⁻³ hPa⁻¹. This variation can be accounted for using a barometric pumping model, coupled with natural ventilation in winter, and including internal mixing as well. After correction, radon concentrations exhibit residual temporal variation, poorly correlated between different points, with standard deviations varying from 3 to 6%. This study shows that temporal variation of radon concentrations in underground cavities can be understood to a satisfactory level of detail using non-linear and time-dependent modelling. It is important to understand the temporal variation of radon concentrations and the limitations in their modelling to monitor the properties of natural or artificial underground settings, and to be able to assess the existence of new processes, for example associated with the preparatory phases of volcanic eruptions or earthquakes.     

Indoor radon concentration in geothermal areas of central Italy

The indoor radon (²²²Rn) activity concentration was measured between January and June in the schools of two geothermal areas in Tuscany, central Italy. One of these areas (the Larderello area) is characterized by a large number of geothermal power plants, covering about 9% of the world’s geothermal power production. In contrast, the other area, Monte Pisano, has not any such facilities. About 250 measurements were made using track etch detectors. Only a slight difference in the concentrations between the two major sampling areas (98 Bq m⁻³ for Larderello area and 43 Bq m⁻³ for Monte Pisano area) was found, and this was related to different geological characteristics of the ground and not the presence of the geothermal plants. The measured radon concentrations were always well below the intervention levels in both areas, and health risks for students and personnel in the examined schools were excluded.     

Escaping radioactivity from coal-fired power plants (CPPs) due to coal burning and the associated hazards: a review

Coal, like most materials found in nature, contains trace quantities of the naturally occurring primordial radionuclides, i.e. of ⁴⁰K and of ²³⁸U, ²³²Th and their decay products. Therefore, the combustion of coal results in the released into the environment of some natural radioactivity (1.48 TBq y⁻¹), the major part of which (99 %) escapes as very fine particles, while the rest in fly ash. The activity concentrations of natural radionuclides measured in coals originated from coal mines in Greece varied from 117 to 435 Bq kg⁻¹ for ²³⁸U, from 44 to 255 Bq kg⁻¹ for ²²⁶Ra, from 59 to 205 Bq kg⁻¹ for ²¹⁰Pb, from 9 to 41 Bq kg⁻¹ for ²²⁸Ra (²³²Th) and from 59 to 227 Bq kg⁻¹ for ⁴⁰K. Fly ash escapes from the stacks of coal-fired power plants in a percentage of 3-1% of the total fly ash, in the better case. The natural radionuclide concentrations measured in fly ash produced and retained or escaped from coal-fired power plants in Greece varied from 263 to 950 Bq kg⁻¹ for ²³⁸U, from 142 to 605 Bq kg⁻¹ for ²²⁶Ra, from 133 to 428 Bq kg⁻¹ for ²¹⁰Pb, from 27 to 68 Bq kg⁻¹ for ²²⁸Ra (²³²Th) and from 204 to 382 Bq kg⁻¹ for ⁴⁰K. About 5% of the total ash produced in the coal-fired power plants is used as substitute of cement in concrete for the construction of dwellings, and may affect indoor radiation doses from external irradiation and the inhalation of radon decay products (internal irradiation) is the most significant. The resulting normalized collective effective doses were 6 and 0.5 man-Sv (GW a)⁻¹ for typical old and modern coal-fired power plants, respectively.     

Soil radium, soil gas radon and indoor radon empirical relationships to assist in post-closure impact assessment related to near-surface radioactive waste disposal

Least squares (LS), Theil’s (TS) and weighted total least squares (WTLS) regression analysis methods are used to develop empirical relationships between radium in the ground, radon in soil and radon in dwellings to assist in the post-closure assessment of indoor radon related to near-surface radioactive waste disposal at the Low Level Waste Repository in England. The data sets used are (i) estimated ²²⁶Ra in the <2 mm fraction of topsoils (eRa226) derived from equivalent uranium (eU) from airborne gamma spectrometry data, (ii) eRa226 derived from measurements of uranium in soil geochemical samples, (iii) soil gas radon and (iv) indoor radon data. For models comparing indoor radon and (i) eRa226 derived from airborne eU data and (ii) soil gas radon data, some of the geological groupings have significant slopes. For these groupings there is reasonable agreement in slope and intercept between the three regression analysis methods (LS, TS and WTLS). Relationships between radon in dwellings and radium in the ground or radon in soil differ depending on the characteristics of the underlying geological units, with more permeable units having steeper slopes and higher indoor radon concentrations for a given radium or soil gas radon concentration in the ground. The regression models comparing indoor radon with soil gas radon have intercepts close to 5 Bq m⁻³ whilst the intercepts for those comparing indoor radon with eRa226 from airborne eU vary from about 20 Bq m⁻³ for a moderately permeable geological unit to about 40 Bq m⁻³ for highly permeable limestone, implying unrealistically high contributions to indoor radon from sources other than the ground. An intercept value of 5 Bq m⁻³ is assumed as an appropriate mean value for the UK for sources of indoor radon other than radon from the ground, based on examination of UK data. Comparison with published data used to derive an average indoor radon: soil ²²⁶Ra ratio shows that whereas the published data are generally clustered with no obvious correlation, the data from this study have substantially different relationships depending largely on the permeability of the underlying geology. Models for the relatively impermeable geological units plot parallel to the average indoor radon: soil ²²⁶Ra model but with lower indoor radon: soil ²²⁶Ra ratios, whilst the models for the permeable geological units plot parallel to the average indoor radon: soil ²²⁶Ra model but with higher than average indoor radon: soil ²²⁶Ra ratios.     

Radioactivity measurements in moss (Hypnum cupressiforme) and lichen (Cladonia rangiformis) samples collected from Marmara region of Turkey

The present study was conducted to compare the ¹³⁷Cs, ⁴⁰K, ²³²Th, and ²³⁸U activity concentrations in epigeic moss (Hypnum cupressiforme) and lichen (Cladonia rangiformis). The activity levels in 37 moss and 38 lichen samples collected from the Marmara region of Turkey were measured using a gamma spectrometer equipped with a high purity germanium (HPGe) detector. The activity concentrations of ¹³⁷Cs, ⁴⁰K, ²³²Th, and ²³⁸U in the moss samples were found to be in the range of 0.36-8.13, 17.1-181.1, 1.51-6.17, and 0.87-6.70 Bq kg⁻¹ respectively, while these values were below detection limit (BDL)-4.32, 16.6-240.0, 1.32-6.47, and BDL-3.57 Bq kg⁻¹ respectively in lichen. The average moss/lichen activity ratios of ¹³⁷Cs, ⁴⁰K, ²³²Th, and ²³⁸U were found to be 1.32 ± 0.57, 2.79 ± 1.67, 2.11 ± 0.82, and 2.19 ± 1.02, respectively. Very low ¹³⁷Cs concentrations were observed in moss and lichen samples compared to soil samples collected from the same locations in a previous study. Seasonal variations of the measured radionuclide activities were also examined in the three sampling stations.     

Recent atmospheric lead deposition recorded in an ombrotrophic peat bog of Great Hinggan Mountains, Northeast China, from Pb and Cs dating

Radioactive markers are useful in dating lead deposition patterns from industrialization in peat archive. Peat cores were collected in an ombrotrophic peat bog in the Great Hinggan Mountains in Northeast China in September 2008 and dated using ²¹⁰Pb and ¹³⁷Cs radiometric techniques. The mosses in both cores were examined systematically for dry bulk density, water and ash content. Lead also was measured using atomic emission spectroscopy with inductively coupled plasma (ICP-AES). Both patterned peat profiles were preserved well without evident anthropogenic disturbance. Unsupported ²¹⁰Pb and ¹³⁷Cs decreased with the depth in both of the two sample cores. The ²¹⁰Pb chronologies were established using the constant rate of supply model (CRS) and are in good agreement with the ¹³⁷Cs time marker. Recent atmospheric ²¹⁰Pb flux in Great Hinggan Mountains peat bog was estimated to be 337 Bq m⁻² y⁻¹, which is consistent with published data for the region. Lead deposition rate in this region was also derived from these two peat cores and ranged from 24.6 to 55.8 mg m⁻² y⁻¹ with a range of Pb concentration of 14-262 μg g⁻¹. The Pb deposition patterns were consistent with increasing industrialization over the last 135-170 y, with a peak of production and coal burning in the last 50 y in Northeast China. This work presents a first estimation of atmospheric Pb deposition rate in peatlands in China and suggests an increasing trend of environmental pollution due to anthropogenic contaminants in the atmosphere. More attention should be paid to current local pollution problems, and society should take actions to seek a balance between economic development and environmental protection.