弯辊和串辊对带钢板形影响

基于有限元软件ANSYS建立了冷轧六辊轧机的三维弹塑性有限元参数化模型。将轧机实体模型转换成有限元模型,根据轧机的工作方式提炼出边界条件和载荷条件,施加在有限元模型上。参数化模型采用ANSYS参数化设计语言APDL编写。通过修改程序中的参数,计算分析了弯辊力、中间辊的串辊量以及带钢宽度等参数对带钢形状和辊缝的影响。计算结果表明:当带钢宽度小于1 300 mm时,调整弯辊力对带钢板形的改变较为明显;当带钢宽度大于1 700 mm时,调整弯辊力对改变带钢板形的作用变得非常小,此时通过连续可变凸度轧辊（CVC）的串辊来调节板形更有效。该结论与冷轧厂实践结论一致。     

14辊轧机辊系变形的有限元分析

针对现场应用的14辊轧机,利用三维有限元软件MSC.MARC建立三维辊系弹性变形有限元模型,求解三维辊系复杂变形,分析第一中间辊抽动和中间辊凸度对承载辊缝的影响。研究得出第一中间辊抽动量在0-50mm时,带材边部厚度的调节范围;中间辊凸度与轧后板凸度呈线性关系,即中间辊凸度越大,辊系的横向刚度也越大。     

连退炉导向辊热凸度对辊形及带钢应力分布的影响

为了更有效地控制连退炉内导向辊热凸度和改善带钢的跑偏及瓢曲变形,以单锥度辊为研究对象,运用MARC有限元软件,定量计算了在加热段和快冷段不同导向辊温差时的导向辊热凸度及其对导向辊辊形和带钢应力分布的影响.研究发现：导向辊热凸度随导向辊温差增大呈直线上升的趋势.在加热段,随着导向辊温差的增大,导向辊产生热凸度后的形状分别为双锥度辊、单锥度辊和“M”型辊,带钢张应力和带钢最大应力分布随着导向辊温差的增大而改变;在快冷段,导向辊产生热凸度后变为双锥度辊,导向辊热凸度会影响带钢张应力值和最大应力值,但不影响其分布.     

VC辊平整机板形调控性能的研究

以某厂连续退火平整机为研究对象,利用ANSYS有限元软件建立VC辊系静力学仿真模型,并研究了弯辊力、VC辊油压、轧辊辊径和辊套厚度对连续退火平整机板形控制能力的影响。结果表明,无论内、外弯辊如何配合,都不能达到只改变四次凸度的目的,不可能只通过内、外弯辊的配合来消除高次浪形;外弯辊的调控功效比内弯辊增大42%;VC辊油压的调控效果主要体现在二次凸度的改变上,改变油压后对四次凸度的影响不大;当VC辊承载时,油压不能始终保持辊套向外涨,承载时辊套可能发生反弯,向芯辊内凹陷;与大辊径相比,小辊径弯辊和油压的调控效果会增加,但辊缝横向刚度会降低;辊套壁厚的减小会使VC辊油压的调控能力有所提高。     

六辊CVC轧机轧辊弯曲和压扁变形的有限元分析

采用非线性弹塑性有限元法,利用大型非线性有限元软件MSC.Marc建立了六辊CVC轧机轧制过程三维有限元仿真模型。模型将辊系弹性变形与轧件弹塑性变形耦合在一起,进行统一建模与分析。运用该模型分别改变工作辊弯辊力、中间辊弯辊力、中间辊横移量进行有限元模拟,得到了工作辊弯辊、中间辊弯辊、中间辊横移对六辊CVC轧机轧辊弯曲和压扁变形的影响规律。所建模型与分析结果可为六辊CVC轧机的板形控制研究提供理论数据与参考依据。     

方矩形管连续辊弯成型延伸规律

为了减小方矩形管辊弯成型时纵向延伸,结合某厂实际生产工艺,建立了方矩形管辊弯成型七机架的三维弹塑性非线性有限元模型。通过仿真分析得到了方矩形管辊弯成型时横向金属流动规律及纵向延伸率的分布规律,与现场测量结果一致。分析了轧辊转速、管坯壁厚、辊径位置等因素对延伸率的影响,在此基础上优化了辊弯轧制工艺参数。结果表明:优化后的辊弯轧制工艺提高了方矩形管的成型质量,为预测最终成型尺寸精度和辊弯成形工艺参数的制定提供了理论依据。     

弯辊力对冷轧板带板形的影响分析

采用ANSYS/LS-DYNA软件,基于显示动力学有限元法,以四辊轧机为例,模拟5 mm厚板带钢冷轧过程,研究施加在支撑辊正弯辊力分别为0 kN,100 kN和200 kN时对轧件压下量、应力和应变的影响.模拟研究表明,增大正弯支撑辊弯辊力能够使轧件边部和中部所受应力趋于平稳,改善轧件的板形.     

非对称轧制力能参数与带钢张应力分布规律

为深入了解带钢轧制过程中非对称因素对轧制力能参数与带钢张应力分布的影响,应用ABAQUS非线性有限元软件对轧制过程进行二维建模及仿真分析,以轧辊驱动方式非对称、上下工作辊与带钢间接触摩擦润滑条件非对称以及存在异步轧制等3种非对称因素作为研究对象,计算并分析上述非对称因素及其程度对于轧后带钢内部张应力分布、轧制力以及轧制扭矩的影响规律,进而定量分析与比较3种非对称轧制因素对于轧制过程中的力能参数和厚向张应力分布规律的影响程度. 仿真计算表明：3种非对称轧制状态都会导致轧后带钢厚向张应力分布的不对称;3种非对称轧制状态都会明显改变轧制过程力能参数大小;与相应对称轧制状态相比,有些非对称因素可以不同程度地降低轧制力和轧制扭矩. 轧制过程中的非对称因素从不同的角度来分析,是利弊共存的.     

四辊轧机接触压力计算的有限元方法及最小磨辊量的确定

采用有限元方法研究在任意工况下四辊轧机工作辊／支承辊间接触压力沿横向分布的计算原理,并对冷轧工作辊最小磨辊量进行定量分析．与其它方法相比本方法具有应用方便、精度高的特点,可适用于不同的轧制工况．     

四辊轧机接触压力计算的有限元方法及最小磨辊量的确定

采用有限元方法研究在任意工况下四辊轧机工作辊／支承辊间接触压力沿横向分布的计算原理，并对冷轧工作辊最小磨辊量进行定量分析，与其它方法相比本方法具有应用方便、精度高的特点，可适用于不同的轧制工况。     

Improvement on strip flatness of cold temper mills by modifying roll contour shape

A study on roll gap profile (strip profile) control was accomplished in a 1700 mm single-stand temper mill. Some critical problems such as the deviation of work roll contour caused by grinding and wear, the effectiveness of work roll bending were discussed. Using a finite element model, the effects of roll contours (ground and wear) on strip profile were investigated. The roll bending effect on strip thickness was also analyzed. It is pointed out that there are some special features of flatness control in the temper mill: during temper rolling, roll deformation is slight due to small rolling load, and the loaded roll gap profile mainly depends on work roll contour, while the backup roll has a little effect on gap crown; the effect of bending force on gauge can not be ignored due to the coupling between flatness control and gauge control. A new roll contour arrangement adaptable to the mill was presented and has been put into practical production. The application of the new set of rolls showed some good results: larger crown control range of work roll bender, higher rolling stability, better strip profile and flatness quality.     

Forced transverse vibration of rolls for four-high rolling mill

In order to investigate the forced transverse vibration of rolls under distributed draught pressure and moment of bending roll force, the forced transverse vibration model of rolls for four-high rolling mill was established. The work roll and backup roll were considered as elastic continuous bodies that were joined by a Winkler elastic layer. According to Euler-Bernoulli beam theory, the forced transverse vibration of rolls was analyzed based on modal superposition method. The forced vibration equations were established when the draught pressure and moment of bending roll force were imposed on the rolls respectively. Numerical modeling was made on 2 030 mm cold tandem rolling mill of Baoshan Iron and Steel Company. Simulation results show that when the work roll is only subjected to different forms of draught pressures, the vibration curves of work roll and backup roll are quadratic curves with amplitudes of 0.3 mm and 45 μm, respectively. When only the moments of bending roll force are imposed on the work roll and backup roll, the vibration curves of work roll and backup roll are quadratic curves, and the amplitudes are 5.0 and 1.6 μm, respectively. The influence of moment of bending roll force on the vibration of work roll is related with the bending roll force.     

VCR and ASR technology for profile and flatness control in hot strip mills

The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel （Group） Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations. A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control. In comparison with the conventional backup and work roll contours configuration, the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls（ASR） and varying contact backup rolls（VCR）. A better strip profile and flatness quality, an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.     

WRS轧机工作辊磨损计算及板形调控分析

在热带钢连轧机设计及改造中采用WRS辊系作为下游机座可以增强机组的板形调控能力。从理论上分析了辊系在轧制中的磨损特性，工作辊磨损辊型的计算方法，根据实际轧制工况对其板形的调控、影响因素进行了定量分析。     

逆涂模式下辊间涂液的参数分析

针对逆式辊涂过程将涂敷辊与汲料辊之间的液体流动简化成两无限大平板间的黏性流动,结合流体动力润滑理论和毛细效应条件建立辊涂数学模型,并对方程进行求解。重点研究在涂敷辊分别为刚辊和胶辊的情况下,辊涂参数（辊速比、辊半径、涂液表面张力、入口油膜厚度和辊间间隙）对辊间涂液的影响。结果表明,各参数对涂层液珠均有影响,其中辊速比在涂敷辊为刚辊或胶辊时都是影响涂层油膜厚度的重要因素。     

Preset model of bending force for 6-high reversing cold rolling mill based on genetic algorithm

The hydraulic roll-bending device was studied, which was widely used in modern cold rolling mills to regulate the strip flatness. The loaded roll gap crown mathematic model and the strip crown mathematic model of the reversing cold rolling process were established, and the deformation model of roll stack system of the 6-high 1 250 mm high crown (HC) reversing cold rolling mill was built by slit beam method. The simulation results show that, the quadratic component of strip crown decreases nearly linearly with the increase of the work roll bending force, when the shifting value of intermediate roll is determined by the rolling process. From the first pass to the fifth pass of reversing rolling process, the crown controllability of bending force is gradually weakened. Base on analyzing the relationship among the main factors associated with roll-bending force in reversing multi-pass rolling, such as strip width and rolling force, a preset mathematic model of bending force is developed by genetic algorithm. The simulation data demonstrate that the relative deviation of flatness criterions in each rolling pass is improved significantly and the mean relative deviation of all five passes is decreased from 25.1% to 1.7%. The model can keep good shape in multi-pass reversing cold rolling process with the high prediction accuracy and can be used to guide the production process.