Structure and photovoltaic properties of ZnO nanowire for dye-sensitized solar cells

Aligned ZnO nanowires with different lengths (1 to approximately 4 μm) have been deposited on indium titanium oxide-coated glass substrates by using the solution phase deposition method for application as a work electrode in dye-sensitized solar cells (DSSC). From the results, the increases in length of zinc oxide (ZnO) nanowires can increase adsorption of the N3 dye through ZnO nanowires to improve the short-circuit photocurrent (J_sc) and open-circuit voltage (V_oc), respectively. However, the J_sc and V_oc values of DSSC with ZnO nanowires length of 4.0 μm (4.8 mA/cm² and 0.58 V) are smaller than those of DSSC with ZnO nanowires length of 3.0 μm (5.6 mA/cm² and 0.62 V). It could be due to the increased length of ZnO nanowires also resulted in a decrease in the transmittance of ZnO nanowires thus reducing the incident light intensity on the N3 dye. Optimum power conversion efficiency (η) of 1.49% was obtained in a DSSC with the ZnO nanowires length of 3 μm.     

Effect of TiO2 nanoparticle-accumulated bilayer photoelectrode and condenser lens-assisted solar concentrator on light harvesting in dye-sensitized solar cells

TiO₂ nanoparticles (NPs) with a size of 240 nm (T240), used as a light-scattering layer, were applied on 25-nm-sized TiO₂ NPs (T25) that were used as a dye-absorbing layer in the photoelectrodes of dye-sensitized solar cells (DSSCs). In addition, the incident light was concentrated via a condenser lens, and the effect of light concentration on the capacity of the light-scattering layer was systematically investigated. At the optimized focal length of the condenser lens, T25/T240 double layer (DL)-based DSSCs with the photoactive area of 0.36 cm² were found to have the short circuit current (I_sc) of 11.92 mA, the open circuit voltage (V_oc) of 0.74 V, and power conversion efficiency (PCE) of approximately 4.11%, which is significantly improved when they were compared to the T25 single layer (SL)-based DSSCs without using a solar concentrator (the corresponding values were the I_sc of 2.53 mA, the V_oc of 0.69, and the PCE of 3.57%). Thus, the use of the optimized light harvesting structure in the photoelectrodes of DSSCs in conjunction with light concentration was found to significantly enhance the power output of DSSCs.     

CuInS2 quantum dot-sensitized TiO2 nanorod array photoelectrodes: synthesis and performance optimization

CuInS₂ quantum dots (QDs) were deposited onto TiO₂ nanorod arrays for different cycles by using successive ionic layer adsorption and reaction (SILAR) method. The effect of SILAR cycles on the light absorption and photoelectrochemical properties of the sensitized photoelectrodes was studied. With optimization of CuInS₂ SILAR cycles and introduction of In₂S₃ buffer layer, quantum dot-sensitized solar cells assembled with 3-μm thick TiO₂ nanorod film exhibited a short-circuit current density (I_sc) of 4.51 mA cm⁻², an open-circuit voltage (V_oc) of 0.56 V, a fill factor (FF) of 0.41, and a power conversion efficiency (η) of 1.06%, respectively. This study indicates that SILAR process is a very promising strategy for preparing directly anchored semiconductor QDs on TiO₂ nanorod surface in a straightforward but controllable way without any complicated fabrication procedures and introduction of a linker molecule.     

Synthesis and characterisation of thin-film TiO2 dye-sensitised solar cell

A TiO₂ dye-sensitised solar cell (DSSC) is fabricated and characterised using: X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), electron diffraction X-ray (EDX) analysis, UV–vis spectrometry and a current?voltage (I?V) test. Thicker anatase TiO₂ gives rise to better crystallinity and subsequently leads to better cell efficiency. Mesoporous TiO₂ with a suitable, average pore size results in higher conversion efficiency. Smaller particle sizes lead to higher dye uptake and increase short circuit current density, J_sc. Addition of scattering layer and/or dual TiCl₄ treatment for DSSCs having optimum thickness enhanced their performance. A DSSC having double TiO₂ layers (20 nm+50 nm) with dual TiCl₄ treatment achieved the highest conversion efficiency of 9.78%.     

Rutile TiO2-modified multi-wall carbon nanotubes in TiO2 film electrodes for dye-sensitized solar cells

The beneficial influence of incorporation of acid-treated and rutile TiO₂ (r-TiO₂)-modified multi-wall carbon nanotubes (MWNTs) in TiO₂ films on photocurrent–voltage characteristics of dye-sensitized solar cells (DSSCs) was studied. Two different routes were adopted for the modification of acid-treated MWNTs (a-MWNTs) with r-TiO₂. The films and MWNTs were characterized by electron microscopy, energy dispersive X-ray spectroscopy, XRD and Raman spectroscopy. In the case of incorporation of a-MWNTs with r-TiO₂ modification, short-circuit photocurrent (J _sc) of the pertinent DSSC increased by 35% compared with that of a cell with bare TiO₂ film. The open-circuit voltage remained almost the same for all cases. The enhanced J _sc is explained by the increased surface area of the film, enhanced cluster formation of TiO₂ particles around a-MWNTs, and improved interconnectivity of TiO₂ particles in the presence of a-MWNTs.     

Optimizing the Aspect Ratio of Nanopatterned Mesoporous TiO2 Thin-Film Layer to Improve Energy Conversion Efficiency of Perovskite Solar Cells

The energy conversion efficiency (ECE) (η), current density (J_sc), open-circuit voltage (V_oc), and fill factor (ff) of perovskite solar cells were studied by using the transmittance of a nanopatterned mesoporous TiO₂ (mp-TiO₂) thin-film layer. To improve the ECE of perovskite solar cells, a mp-TiO₂ thin-film layer was prepared to be used as an electron transport layer (ETL) via the nanoimprinting method for nanopatterning, which was controlled by the aspect ratio. The nanopatterned mp-TiO₂ thin-film layer had a uniform and well-designed structure, and the diameter of nanopatterning was 280 nm. The aspect ratio was controlled at the depths of 75, 97, 127, and 167 nm, and the perovskite solar cell was fabricated with different depths. The ECE of the perovskite solar cells with the nanopatterned mp-TiO₂ thin-film layer was 14.50%, 15.30%, 15.83%, or 14.24%, which is higher than that of a non-nanopatterned mp-TiO₂ thin-film layer (14.07%). The enhancement of ECE was attributed to the transmittance of the nanopatterned mp-TiO₂ thin-film layer that is due to the improvement of the electron generation. As a result, better electron generation affected the electron density, and J_sc increased the V_oc, and ff of perovskite solar cells.     

Efficiency improvement of dye-sensitized tandem solar cell by increasing the photovoltage of the back sub-cell

In tandem-structured dye-sensitized solar cell (DSSC) composed of two parallel-connected sub-cells, the photovoltage (V_oc) generated by the back sub-cell is usually rather low, resulting in low V_oc and conversion efficiency (η) of the tandem cell. To solve this issue, two simple but very efficient strategies, namely, the filling of Li⁺-absent electrolyte and/or coating Al₂O₃ on TiO₂ electrode surface in the back sub-cell, were explored to enhance the V_oc of the back sub-cell and hence that of the tandem cell. The former strategy was expected to heighten the energy level of TiO₂ conduction band, and the latter one to retard the charge recombination. The photovoltaic performance measurements reveal that in the both cases, although there was a slight decrease in the photocurrent (J_sc), an obvious rise in the V_oc was achieved for the tandem cells, leading to significant improvements in η of the tandem cells. Compared to the individual organic dye-sensitized solar cell (the highest η is 7.58%), the tandem cell with two organic dyes having complementary absorption spectra demonstrates an improved efficiency of up to 8.33% by a combinational application of Li⁺-absent electrolyte and Al₂O₃ overcoat. The results presented in this study highlight that the efficiency of a parallel-connected tandem-structured DSSC can be improved significantly through enhancing the photovoltage of the back sub-cell, which is first time reported.     

Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

TiO2 micro-flowers composed of nanotubes and their application to dye-sensitized solar cells

TiO₂ micro-flowers were made to bloom on Ti foil by the anodic oxidation of Ti-protruding dots with a cylindrical shape. Arrays of the Ti-protruding dots were prepared by photolithography, which consisted of coating the photoresists, attaching a patterned mask, illuminating with UV light, etching the Ti surface by reactive ion etching (RIE), and stripping the photoresist on the Ti foil. The procedure for the blooming of the TiO₂ micro-flowers was analyzed by field emission scanning electron microscopy (FESEM) as the anodizing time was increased. Photoelectrodes of dye-sensitized solar cells (DSCs) were fabricated using TiO₂ micro-flowers. Bare TiO₂ nanotube arrays were used for reference samples. The short-circuit current (J_sc) and the power conversion efficiency of the DSCs based on the TiO₂ micro-flowers were 4.340 mA/cm² and 1.517%, respectively. These values of DSCs based on TiO₂ micro-flowers were higher than those of bare samples. The TiO₂ micro-flowers had a larger surface area for dye adsorption compared to bare TiO₂ nanotube arrays, resulting in improved J_sc characteristics. The structure of the TiO₂ micro-flowers allowed it to adsorb dyes very effectively, also demonstrating the potential to achieve higher power conversion efficiency levels for DSCs compared to a bare TiO₂ nanotube array structure and the conventional TiO₂ nanoparticle structure.     

Anodic TiO2 Nanotube Arrays for Dye-Sensitized Solar Cells Characterized by Electrochemical Impedance Spectroscopy

This paper reports on the microstructure of anodic titanium oxide (TiO₂) and its use in a dye-sensitized solar cell (DSSC) device. When voltages of 60 V were applied to titanium foil for 2 hr under 0.25 wt% NH₄F+ 2 vol% H₂O+C₂H₄(OH)₂, TiO₂ with a nanotube structure was formed. The film, which had a large surface area, was used as an electron transport film in the DSSC. The DSSC device had a short-circuit current density (J_sc) of 12.52 mA cm⁻², a fill factor (FF) of 0.65, an open-voltage (V_oc) of 0.77 V, and a photocurrent efficiency of 6.3% under 100% AM 1.5 light. The internal impedance values under 100%, 64%, 11%, and 0% (dark) AM 1.5 light intensities were measured and simulated using the electrical impedance spectroscopy (EIS) technique. The impedance characteristics of the DSSC device were simulated using inductors, resistors, and capacitors. The Ti/TiO₂, TiO₂/Electrolyte, electrolyte, and electrolyte/(Pt/ITO) interfaces were simulated using an RC parallel circuit, and the bulk materials, such as the Ti, ITO and conducting wire, were simulated using a series of resistors and inductors. The impedance of the bulk materials was simulated using L₀+R₀+R_b, the impedance of the working electrode was simulated using (C₁//R₁)//(R_a+(C₂//R₂), the electrolyte was simulated using C₃//R₃, and the counter electrode was simulated using C₄//R₄.     

Efficiency enhancement in dye sensitized solar cells based on PAN gel electrolyte with Pr4NI + MgI2 binary iodide salt mixture

The effect of using a binary iodide salt mixture in N719 dye-sensitized TiO₂ solar cells (DSSCs) is investigated. The cells use tetrapropylammonium iodide (Pr₄NI) and magnesium iodide (MgI₂) in a plasticized polyacrylonitrile gel in glass/FTO/nano-porous TiO₂/gel, I₂/Pt/FTO/glass solar cell structure. The salt composition in the gel electrolyte is varied to optimize the efficiency of DSSCs. The DSSCs with MgI₂ or Pr₄NI as the only iodide salt showed the efficiencies 2.56 and 4.16 %, respectively, under AM 1.5 (100 mW cm^?2) illumination while the DSSC with mixed cations with 18.4:81.6 MgI₂:Pr₄NI molar ratio shows the highest efficiency of 5.18 %. Thus the efficiency enhancement, relative to the high efficiency end member is about 25 %. DC polarization measurements establish the predominantly ionic behavior of the electrolytes, and show that the variation of efficiency with salt composition correlates with the change in short circuit photocurrent density (J _sc), which appears to be governed by the iodide ion conductivity. It is also found that J _sc correlates with the iodide ion transference number estimated from DC polarization data taken with non-blocking iodine electrodes. This study suggests that binary iodide mixtures may be used to obtain efficiency enhancement in different types of DSSCs based on polymeric, gel, or solvent electrolytes.     

Structural, morphological, and optical properties of TiO2 thin films synthesized by the electro phoretic deposition technique

In this work, we report the structural, morphological, and optical properties of TiO₂ thin films synthesized by the electro phoretic deposition technique. The TiO₂ film was formed on a doped fluorine tin oxide (SnO₂:F, i.e., FTO) layer and used as a photo electrode in a dye solar cell (DSC). Using spectroscopic ellipsometry measurements in the 200 to 800 nm wavelengths domain, we obtain a thickness of the TiO₂ film in the range of 70 to 80 nm. Characterizations by X-ray diffraction and atomic force microscopy (AFM) show a polycrystalline film. In addition, AFM investigation shows no cracks in the formed layer. Using an ultraviolet–visible near-infrared spectrophotometer, we found that the transmittance of the TiO₂ film in the visible domain reaches 75%. From the measured current–voltage or I-V characteristic under AM1.5 illumination of the formed DSC, we obtain an open circuit voltage V_oc = 628 mV and a short circuit current I_sc = 22.6 μA, where the surface of the formed cell is 3.14 cm².     

The effect of dye-sensitized solar cell based on the composite layer by anodic TiO2 nanotubes

TiO₂ nanotube arrays are very attractive for dye-sensitized solar cells (DSSCs) owing to their superior charge percolation and slower charge recombination. Highly ordered, vertically aligned TiO₂ nanotube arrays have been fabricated by a three-step anodization process. Although the use of a one-dimensional structure provides an enhanced photoelectrical performance, the smaller surface area reduces the adsorption of dye on the TiO₂ surface. To overcome this problem, we investigated the effect of DSSCs constructed with a multilayer photoelectrode made of TiO₂ nanoparticles and TiO₂ nanotube arrays. We fabricated the novel multilayer photoelectrode via a layer-by-layer assembly process and thoroughly investigated the effect of various structures on the sample efficiency. The DSSC with a four-layer photoelectrode exhibited a maximum conversion efficiency of 7.22% because of effective electron transport and enhanced adsorption of dye on the TiO₂ surface.     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Photoelectrochemical decomposition of bio-related compounds at a nanoporous semiconductor film photoanode and their photocurrent-photovoltage characteristics

Photoelectrochemical decomposition of bio-related compounds such as amino acids was investigated with a biophotochemical cell comprising a mesoporous TiO₂ thin film photoanode and an O₂-reducing cathode. It was concluded that a kind of Schottky junction formed at the surface of the TiO₂ (called as liquid junction) induced the photodecomposition followed by generation of photocurrent/photovoltage. Complete photodecomposition was investigated by the CO₂ formation yield. The photocurrent-photovoltage (J-V) characteristics of amino acids and other typical bio-related compounds were investigated, and the short circuit photocurrent (J_sc), open circuit photovoltage (V_oc), and Fill factor (ff) were exhibited. Effect of pH on the photodecomposition of phenylalanine and cysteine were studied; for cysteine alkaline conditions gave a high efficiency, which was interpreted by the high electron-donating ability of the dissociated -S⁻ group. The incident light-to-current conversion efficiency (IPCE) of cysteine was 25% at 350 nm. It was for the first time shown that organic acids gave high internal quantum efficiency (η′) over 8 (=800%) in the photodecomposition; for oxalic acid it was 9.3 (=930%) and for butyric acid 8.2. The alternating current impedance spectroscopy of glycine showed that the cell performance is determined by the chemical reactions at TiO₂ or Pt electrodes.     

Sol–gel hydrothermal synthesis of bismuth–TiO2 nanocubes for dye-sensitized solar cell

Bismuth–TiO₂ nanocubes were synthesized via a facile sol–gel hydrothermal method with titanium tetraisopropoxide as the precursor. The influence of the bismuth on the size, morphology, crystallinity and optical behavior of TiO₂ nanocubes were investigated. The samples were characterized by X-ray diffraction analysis (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), field emission scanning electron microscopy (FESEM) and UV–visible spectroscopy (UV–vis). Photovoltaic behavior of dye-sensitized solar cells (DSSCs) fabricated using Bi–TiO₂ nanocubes was studied. The DSSCs had an open-circuit voltage (V_oc) of 590 mV, a short-circuit current density (J_sc) of 7.71 mA/cm², and the conversion efficiency (η) of 2.11% under AM 1.5 illumination, a 77% increment as compared to pure TiO₂ nanocubes.     

Long Vertically Aligned TiO2 Nanotube Electrodes Prepared via Two-Step Anodization for Highly Efficient Photovoltaics

Vertically aligned long TiO₂ nanotube (NT) electrodes with optimized structures for photovoltaic application were prepared by a two-step anodization method. The structures of the conventional TiO₂ NT electrodes prepared by one-step anodization became severely bundled and disordered for tube lengths exceeding 20 μm. On the other hand, two-step anodization resulted in uniform and bundle-free TiO₂ NT electrodes, with tube lengths of up to 38 μm. When used in dye-sensitized solar cells (DSSCs) as photoanodes, the two-step TiO₂ NT electrodes exhibited enhanced short-circuit current density (J_sc) with increasing tube length, owing to an increased roughness factor, which resulted in high dye loading. However, the dark current and open-circuit voltage decay (OCVD) curves confirmed that the electron recombination rate increased, and the electron lifetime decreased, with increasing tube length. This reduced electron lifetime resulted in sharp reductions in the open-circuit voltage (V_oc) with increasing tube length. Owing to the trade-off between the enhanced current density and the reduced electron lifetime, an optimal conversion efficiency of 4.56 % was obtained for a tube length of 29 μm.     

Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).