Surface modification of UHSPE fibers through allylamine plasma deposition. II. Effect on fiber and fiber/epoxy interface

The surface of ultra-high strength polyethylene (UHSPE) fibers was modified using allylamine plasma deposition to improve their adhesion to epoxy resins. Allylamine plasma polymerization was investigated at different power inputs and polymerization times. The adhesion of treated fibers to epoxy resin was studied by single-fiber, pull-out tests. A special silicon rubber mold was developed to embed the single fiber in epoxy resin. The results show that the interfacial shear strength (IFSS) increased by a factor of 2 to 3 after allylamine plasma treatments. The greatest improvement, by a factor of 3.25, was obtained at 30 W for 10 min. Scanning electron microscopy (SEM) was also used to study the surface topography of fibers pulled from the epoxy resin. In most cases, it was observed that pull-out failure occurred at the interface, as evidenced from clean fiber surfaces. In a few cases, however, fibrils were peeled from fibers. The fiber strength decreased, but initial modulus increased after the plasma treatments. The decrease in fiber strength was insignificant for treatments at a lower power input, but was significant at higher power inputs. Treatment time, however, had no significant effect on fiber strength.     

Improvement of adhesion of Kevlar fiber to epoxy by chemical modification

Kevlar 149 fibers were surface-modified by chlorosulfonation and subsequent reaction of -SO₂O with some reagents (e.g. glycine, water, ethylenediamine, and 2-butanol) to improve the adhesion to epoxy resin. The mechanical properties and surface topography of the modified fibers were investigated at different reaction times and reagent concentrations. The surface functional groups introduced into the surface of the fibers were identified by X-ray photoelectron spectroscopy (XPS) and static secondary ion mass spectroscopy (SIMS). The interfacial shear strength (IFSS) between the fibers and epoxy resin was measured by the microbond test. The results showed that the IFSS was markedly improved (by a factor of 2.25) by the chlorosulfonation/glycine treatment and that the fiber strength was not affected. Scanning electron microscopy (SEM) was also used to study the surface topography of fibers pulled from the epoxy resin. Furthermore, energy dispersive X-ray (EDX) spectroscopy was used to qualitatively examine the amount of sulfur in the fiber surfaces and in the fracture surfaces of fibers from microbond pull-out specimens. The results of EDX examination were consistent with a change of the fracture mode from the interface between the fiber and the epoxy resin to a location within the fiber and/or epoxy resin as observed by SEM.     

Effects of XeCl excimer laser treatment of Vectran® fibers and their adhesion to epoxy resin

Vectran^® fibers, made using liquid crystalline polyester, were treated with pulsed XeCl excimer laser (308 nm) to alter their surface characteristics and, thus, improve their adhesion to epoxy resin. The treatments were carried out in air using varying numbers of pulses at different laser fluences. The effects of laser treatment on the fiber surface topography, chemistry and wettability have been investigated. Fiber/epoxy resin interfacial shear strength was measured using the microbead test. The surface roughness was characterized qualitatively and quantitatively using scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. Changes in the surface energy were characterized using the Wilhelmy technique. Based on the SEM micrographs, the threshold fluence for the formation of surface structure was found to be less than 36 mJ/(pulse ? cm²). The laser treatments at fluences higher than the threshold fluence introduced periodic roll (wavy) structures on the fiber surface transverse to the fiber axis. From the AFM results, the fiber surface roughness was found to increase by up to 3.5 times the control fiber after the laser treatment. The dispersion component of the surface energy decreased, while the acid–base component of the surface energy increased significantly from 0 to 8.8 mJ/m² after the laser treatment. The Vectran^® fiber/epoxy resin IFSS increased by up to 75% after the laser treatment. This improvement is mainly attributed to higher surface roughness of the fiber.     

Characterization of ramie fiber/soy protein concentrate (SPC) resin interface

Ramie fiber/soy protein concentrate (SPC) polymer (resin) interfacial shear strength (IFSS) was measured using the microbond technique. To characterize the effect of plasticization, SPC resin was mixed with glycerin. Fibers were also treated with ethylene plasma polymer to reduce fiber surface roughness and polar nature to control the IFSS. Fiber surfaces after ethylene plasma polymerization, and fracture surfaces of specimens before and after the microbond tests were characterized using a scanning electron microscope (SEM). Some specimens were also characterized using electron microprobe analyzer (EMPA) to map the residual resin on the fiber surface after the microbond test. Effects of glycerin concentration in SPC and ethylene plasma fiber surface treatment time on the IFSS were investigated. Preparation of SPC resin requires a large amount of water. As expected, during drying of SPC resin, the microdrops shrank significantly. The high IFSS values indicate strong interfacial interaction in the ramie fiber/SPC resin system. This strong interfacial interaction is a result of a highly polar nature of both the ramie fiber and the SPC resin and rough fiber surface. Ethylene plasma polymerization was used to control the IFSS. The plasma polymer imparted a polyethylene-like, non-polar polymer coating on the fiber surface. As a result, the fiber surface became smoother compared to the untreated fiber. Both fiber smoothness and non-polar nature of the coating reduced the ramie fiber/SPC resin IFSS. Plasticization of the SPC resin by glycerin also decreased the adhesion strength of the ramie fibers with the SPC resin. The load-displacement plots for IFSS tests obtained for different resin and fiber combinations indicate different interfacial failure modes.     

Surface ammonification of the mutual‐irradiated aramid fibers in 1,4‐dichlorobutane for improving interfacial properties with epoxy resin

The mutual irradiated aramid fibers in 1,4‐dichlorobutane was ammoniated by ammonia/alcohol solution, in an attempt to improve the interfacial properties between aramid fibers and epoxy matrix. Scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS), dynamic contact angle analysis (DCA), interfacial shear strength (IFSS), and single fiber tensile testing were carried out to investigate the functionalization process of aramid fibers and the interfacial properties of the composites. Experimental results showed that the fiber surface elements content changed obviously as well as the roughness through the radiation and chemical reaction. The surface energy and IFSS of aramid fibers increased distinctly after the ammonification, respectively. The amino groups generated by ammonification enhanced the interfacial adhesion of composites effectively by participating in the epoxy resin curing. Moreover, benefited by the appropriate radiation, the tensile strength of aramid fibers was not affected at all. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44924.     

RETRACTED ARTICLE: Surface modification of aramid fibers with novel chemical approach

Friedel–Crafts Reaction as a simple and convenient approach to the surface modification of aramid fiber was introduced in this paper. Epoxy chloropropane was chosen as the treatment reagent to modify aramid fibers surface via Graft reaction. After the modification, the interfacial properties of aramid/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) value of aramid/epoxy composites was enhanced by about 50%, and the tensile strength of aramid fibers had no obvious damage. The crystalline state of aramid fibers was determined by X-ray diffraction instrument (XRD), and the results showed that there were not any distinct crystal type varieties. The surface elements of aramid fibers were determined by X-ray photoelectron spectroscopy (XPS), the analysis of which showed that the oxygen/carbon ratio of aramid fiber surface increased obviously. The possible changes of the chemical structure of aramid fibers were investigated via Fourier transform infrared spectrum (FTIR), and the analysis of which showed that the epoxy functional groups were grafted into the molecule structure of aramid fibers. The surface morphology of aramid fibers was analyzed by Scanning electron microscope (SEM), and the SEM results showed that the physical structure of aramid fibers was not etched or damaged obviously. The surface energy of aramid fibers was investigated via the dynamic capillary method, and the results showed that the surface energy was enhanced by 31.5%, and then the wettability degree of aramid fiber surface was enhanced obviously too. All of the results indicated that this novel chemical modification approach not only can improve the interfacial bonding strength of aramid/epoxy composites remarkably, but also have no negative influence on the intrinsic tensile strength of aramid fibers.     

Mechanical properties of carbon fiber composites modified with nano-SiO2 in the interphase

The performance of carbon fibers-reinforced composites is dependent to a great extent on the properties of fiber–matrix interface. To improve the interfacial properties in carbon fibers/epoxy composites, nano-SiO₂ particles were introduced to the surface of carbon fibers by sizing treatment. Atomic force microscope (AFM) results showed that nano-SiO₂ particles had been introduced on the surface of carbon fibers and increase the surface roughness of carbon fibers. X-ray photoelectron spectroscopy (XPS) showed that nano-SiO₂ particles increased the content of oxygen-containing groups on carbon fibers surface. Single fiber pull-out test (IFSS) and short-beam bending test (ILSS) results showed that the IFSS and ILSS of carbon fibers/epoxy composites could obtain 30.8 and 10.6% improvement compared with the composites without nano-SiO₂, respectively, when the nano-SiO₂ content was 1 wt % in sizing agents. Impact test of carbon fibers/epoxy composites treated by nano-SiO₂ containing sizing showed higher absorption energy than that of carbon fibers/epoxy composites treated by sizing agent without nano-SiO₂. Scanning electron microscopy (SEM) of impact fracture surface showed that the interfacial adhesion between fibers and matrix was improved after nano-SiO₂-modified sizing treatment. Dynamic mechanical thermal analysis (DMTA) showed that the introduction of nano-SiO₂ to carbon fibers surface effectively improved the storage modulus of carbon fibers/epoxy.     

Effect of ultrasound on wettability between aramid fibers and epoxy resin

Good wetting of reinforced fiber by resin was a main factor in the improvement of the interface adhesion of their composites. Ultrasound with a frequency of 20 kHz was used to improve the wettability between aramid fibers and epoxy resin during the winding process of the composites. The effects of ultrasound on the viscosity and surface tension of epoxy resin and on the surface characteristics of aramid fibers were investigated. The wettability of aramid fibers and treated epoxy resin under different conditions and of aramid fibers and epoxy resin under ultrasonic online treatment were compared. The results indicated that the main action of ultrasound was to force epoxy resin to impregnate aramid fibers, in addition to the influence of ultrasound on the properties of epoxy resin and aramid fibers. The results of microdebond testing showed that the interfacial shear strength (IFSS) of aramid/epoxy composites could be 26% higher than that of untreated composites because of the improved wettability between aramid fibers and epoxy resin subjected to ultrasonic online treatment. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Surface modification of ultra high modulus polyethylene fibers by an atmospheric pressure plasma jet

To improve their adhesion properties, ultra high modulus polyethylene (UHMPE) fibers were treated by an atmospheric pressure helium plasma jet (APPJ), which was operated at radio frequency (13.56 MHz). The surface properties of the fibers were investigated by X‐ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and contact angle measurement. The surface dyeability improvement after plasma treatments was investigated using laser scanning confocal microscopy (LSCM). The adhesion strengths of the fibers with epoxy were evaluated by microbond tests. In addition, the influence of operational parameters of the plasma treatment including power input and treatment temperature was studied. XPS analysis showed a significant increase in the surface oxygen content. LSCM results showed that the plasma treatments greatly increased fluorescence dye concentrations on the surface and higher diffusion rate to the fiber center. The tensile strength of UHMPE fiber either remained unchanged or decreased by 10–13.6% after plasma treatment. The contact angle exhibited a characteristic increase in wettability, due to the polar groups introduced by plasma treatment. The microbond test showed that the interfacial shear strengths (IFSS) increase significantly (57–139%) after plasma treatment for all groups and the optimum activation is obtained at 100°C and 5 W power input. SEM analysis showed roughened surfaces after the plasma treatments. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Wettability assessment of plasma-treated PBO fibers based on thermogravimetric analysis

Changes in the surface wettability of poly(p-phenylene benzobisoxazole) (PBO) fibers were investigated by thermogravimetric analysis (TGA) following an air dielectric barrier discharge (DBD) plasma treatment. The results were then supplemented and confirmed by scanning electron microscopy (SEM), dynamic contact angle analysis (DCAA), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) measurements. After exposure to the DBD plasma at a pre-determined power level, TGA analysis showed that the residual rates retained by the PBO composites decreased, which meant an increase in the amount of resin coating the PBO fibers in the composites. Observations by SEM confirmed that there was more resin adhering to the treated PBO fibers and the wetting behavior of resin on the fibers was greatly improved. Meanwhile, DCAA for the treated fibers showed a significant enhancement in fiber surface free energy. XPS and AFM were performed in order to reveal any variations in fiber surface activity and surface morphology resulting from the surface treatment. The resulting data showed that increases in oxygen-containing polar groups and surface roughness on the plasma-treated PBO fibers contributed to the above improved wetting behavior. With comprehensive analyses, it was concluded that TGA could be used as a supporting method assessing the surface wettability of PBO fibers before and after air DBD plasma treatment.     

Effect of Atmospheric Plasma Treatment on Carbon Fiber/Epoxy Interfacial Adhesion

In this work the effect of atmospheric plasma treatment on carbon fiber has been studied. The carbon fibers were treated for 1, 3 and 5 min with a He/O₂ dielectric barrier discharge atmospheric pressure plasma. The fiber surface morphology, surface chemical composition and interfacial shear strength between the carbon fiber and epoxy resin were investigated using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and the single fiber composite fragmentation test. Compared to untreated carbon fibers, the plasma treated fiber surfaces exhibited surface morphological and surface composition changes. The fiber surfaces were found to be roughened, the oxygen content on the fiber surfaces increased, and the interfacial shear strength (IFSS) improved after the atmospheric pressure plasma treatment. The fiber strength showed no significant changes after the plasma treatment.     

Effect of sizing on interfacial adhesion of commercial high strength carbon fiber‐reinforced resin composites

The influence of sizing agent on interfacial shear strength (IFSS) of carbon fiber/epoxy (CF/EP) and carbon fiber/bismaleimide (CF/BMI) was investigated. Since sizing agent can alter physicochemical properties of CF surface, possible affecting factors, including sizing reactivity, chemical reactions between sizing and resin, wettability of fiber with resin, fiber surface roughness, and chemical composition of fiber surface, were discussed. It is found that contact angle of fiber with resin and sufficient chemical reactions between sizing and resin reveal strong correlation with the interfacial adhesion of CF/EP and CF/BMI, while the effect of surface roughness and the amount of oxygen on the fiber surface are relatively weak. Due to EP type of the composition, the sizing agent tends to improve the wettability of CF with EP, while goes against for the fiber with BMI. POLYM. COMPOS., 254–261, 2016. © 2014 Society of Plastics Engineers     

淀粉纳米晶对玻璃纤维的表面改性研究

采用自制的淀粉纳米晶(SNC)对玻璃纤维进行表面处理,增加其与环氧树脂基体的界面剪切强度(IFSS)。研究了处理方式、处理时间、SNC乙醇分散液浓度、热处理温度等工艺参数对SNC在玻璃纤维表面沉积情况的影响,以及对改性玻璃纤维与环氧树脂的界面性能的影响规律。采用扫描电子显微镜、单纤维强力仪对处理前后玻璃纤维进行表征,并采用微脱粘法测试玻璃纤维与环氧树脂的界面粘结情况。结果表明,当重力静置处理时间24 h,SNC乙醇分散液浓度为1 g/100 m L时,SNC在玻璃纤维表面均匀沉积,且能显著提高玻璃纤维与环氧树脂的IFSS,为27.29 MPa,较未处理的纤维增加29.3%。150℃热处理4 h后,X射线光电子能谱结果显示SNC与玻璃纤维形成化学键合,进一步增加纤维与环氧树脂的界面粘结,IFSS值达到32.30 MPa,较未处理的纤维增加53%,且纤维的拉伸强度得到较好的维持。     

Increasing the interfacial strength in carbon fiber/epoxy composites by controlling the orientation and length of carbon nanotubes grown on the fibers

Multi-walled carbon nanotubes (MWCNTs) were grafted onto carbon fibers (CFs) using an injection chemical vapor deposition method. The orientation and length (16.6–108.6 μm) of the MWCNTs were controlled by the surface treatment of the CFs and the growth time, respectively. The interface between the MWCNTs and the CFs indicated the grafted CNTs were immobilized by embedding catalyst on CFs. Two orders of magnitude increase in the specific surface areas of CFs was obtained by grafting the MWCNT. MWCNT–CF hybrids exhibited good wettability with the epoxy resin due to the surface roughness and capillary action. Single-fiber composite fragmentation tests revealed an remarkable improvement of interfacial shear strength (IFSS) controlled by the orientation and length of MWCNTs. MWCNTs with an perpendicular alignment and long length showed a high IFSS in epoxy composites due to better wettability and a large contact interface between the hybrids and the resin. Hybrids with an optimum length (47.2 μm) of aligned MWCNTs showed a dramatic improvement of IFSS up to 175% compared to that of pristine CFs.     

Surface modification of PBO fibers by argon plasma and argon plasma combined with coupling agents

The methods of argon plasma and argon plasma combined with coupling agents were employed to modify the poly[1,4‐phenylene‐cis‐benzobisoxazole] (PBO) fiber surface. The interfacial shearing strength (IFSS) of PBO fibers/epoxy resin was measured by the single fiber pull‐out test. The surface chemical structure and surface composition of PBO fibers were determined by FTIR and X‐ray photoelectron spectroscopy respectively. The morphology of the fiber surface was investigated by scanning electron microscopy and the specific surface area of the fibers was calculated by B.E.T. equation. Furthermore, the wettability of PBO fibers was confirmed by the droplet profile analysis method. The results showed that the elemental composition ratio of the fiber surface changed after the modification. The IFSS increased by 42 and 78% when the fibers were treated by argon plasma and argon plasma combined with the coupling agents, respectively. Meanwhile, the specific surface areas of the treated fibers were improved. In addition, compared with the modification of argon plasma, the modification of argon plasma combined with the coupling agents inhibited the attenuation phenomena of the IFSS and the wettability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1428–1435, 2006     

Improvement of Interfacial Adhesion of Glass Fiber/Epoxy Composite by Using Plasma Polymerized Glass Fibers

This study intends to produce plasma polymer thin films of γ-glycidoxypropyltrimethoxysilane (γ-GPS) on glass fibers in order to improve interfacial adhesion of glass fiber-reinforced epoxy composites. A low frequency (LF) plasma generator was used for the plasma polymerization of γ-GPS on the surface of glass fibers at different plasma powers and exposure times. X-ray photoelectron spectroscopy (XPS) and SEM analyses of plasma polymerized glass fibers were conducted to obtain some information about surface properties of glass fibers. Interlaminar shear strength (ILSS) values and interfacial shear strength (IFSS) of composites reinforced with plasma polymerized glass fiber were evaluated. The ILSS and IFSS values of non-plasma polymerized glass fiber-reinforced epoxy composite were increased 110 and 53%, respectively, after plasma polymerization of γ-GPS at a plasma power of 60 W for 30 min. The improvement of interfacial adhesion was also confirmed by SEM observations of fractured surface of the composites.     

Effects of surface treatment of carbon fiber: Tensile property,surface characteristics,and bonding to epoxy

In this article, effects of electrochemical oxidation and sizing treatment of PAN‐based carbon fibers (CFs) on the tensile properties, surface characteristics, and bonding to epoxy were investigated. As found, the electrochemical oxidation improves the tensile strength of single CF by 16.0%, due to weakening the surface stress concentration and smoothing the surface structure. Further sizing treatment shows a negligible effect on the tensile strength. Both oxidation and sizing treatments significantly improve the wettability and surface energies of CFs by introducing oxygen‐containing functional groups. Microbond test was conducted to characterize the interfacial shear strength (IFSS) between a single fiber and an epoxy droplet. The oxidation treatment increases IFSS slightly, which is due to the contradictory effects of the formation of chemical bonds between the resin and CFs, and the reduced mechanical interlocking. Further sizing treatment significantly enhances IFSS from 73.6 to 81.0 MPa, due to the formation of vast chemical bonds. Furthermore, the oxidation and sizing treatment can effectively reduce the degradation of IFSS to the hygrothermal ageing for the CF/epoxy system. POLYM. COMPOS., 37:2921–2932, 2016. © 2015 Society of Plastics Engineers     

Improvement of the interfacial shear strength of poly(p‐phenylene benzobisoxazole) fiber/epoxy resin composite via a novel surface coating agent

Poly(p‐phenylene benzobisoxazole) (PBO) fiber with a smooth surface exhibits limited interfacial interaction with resin matrix. One of the effective strategies to improve the adhesion between the fiber and resin matrix is through surface modification of the fiber. In this study, we have proposed a novel surface treatment agent based on phosphoester cross‐linked castor oil (PCCO) for effective surface treatment of PBO fibers. The surface treatment agent was prepared by a simple cross‐linking reaction between hydroxy phosphorylated castor oil (PCO) and epoxy resin, with alcohol as the solvent at 65°C. Once the PBO fiber was treated with this agent, the interfacial adhesion between the PBO fiber and the epoxy resin could then be improved. Systematic analyses suggest that the surface treatment with (PCO + epoxy)/alcohol solution improves the interaction of the PBO fiber with the epoxy resin matrix. The PCCO coated onto the surface of PBO fiber acts as a coupling agent, improving the interfacial shear strength (IFSS) of the PBO fiber/epoxy resin composite. Results indicate a 156% increase in IFSS without compromising the mechanical properties of the fiber. POLYM. COMPOS., 37:1198–1205, 2016. © 2014 Society of Plastics Engineers     

Surface modification of aramid fibers with γ‐ray radiation for improving interfacial bonding strength with epoxy resin

Co⁶⁰ γ‐ray radiation as a simple and convenient method for surface modification of Armos aramid fibers was introduced in this article. Two kinds of gas mediums, N₂ and air, were chosen to modify aramid fiber surface by γ‐ray irradiation. After fiber surface treatment, the interlaminar shear strength values of aramid/epoxy composites were enhanced by about 17.7 and 15.8%, respectively. Surface elements of aramid fibers were determined by XPS, the analysis of which showed that the ratio of oxygen/carbon was increased. The crystalline state of aramid fibers was determined by X‐ray diffraction instrument. The surface topography of fibers was analyzed by atomic force microscopy and scanning electron microscope. The degree of surface roughness and the wettability of fiber surface were both enhanced by γ‐ray radiation. The results indicated that γ‐ray irradiation technique, which is a suitable way of batch process for industrialization, can significantly improve the surface properties of aramid fibers reinforced epoxy resin matrix composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Grafting of multifunctional groups onto the surface of high‐strength polyethylene fibers and the interface of their composites

High‐strength polyethylene (HSPE) fibers were oxidated via chemical reactions in an acidic medium, and the carboxyl group was transferred into the acyl chloride and then reacted with pentaerythritol or diethylene triamine to graft the multifunctional group compounds onto the surface of the HSPE fibers. Subtractive Fourier transform infrared spectroscopy and the methylene blue absorbing method were used to study the functional groups on the surface of the modified fibers and their content. The results show that the polar functional groups, including ? COOH, ? OH, and ? NH₂, were introduced onto the surface of the HSPE fibers, and the polar groups improved the wettability. The interface shear stress (IFSS) of the composites that were made from modified fibers and epoxy was measured by means of the microdebond method. The results show that the IFSS was greatly increased by the grafting of pentaerythritol or diethylene triamine onto the HSPE fiber surface. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 449–454, 2005