电解槽控制过程中Al_2O_3浓度特性的研究

对电解槽控制过程中的Al2 O3表现出的一些特性如Al2 O3浓度与槽表观电阻的关系、与电流效率的关系、与AE的关系进行了研究 ,这些研究为电解槽模糊控制技术奠定了基础     

铝电解槽中沉淀的形成及分析

阐述了电解中氧化铝溶解的原理及其溶解行为;指出了电解槽中产生沉淀的原因及沉淀在电解槽中的位置;采用X射线衍射法分析了沉淀物样品的物相组成,物相结果表明,样品中主要包括Na3AlF6、Al2O3、Al和Na5Al3F14,其中Al2O3的含量达到了51%,有的样品中还含有CaF2;最后提出了减少或避免沉淀的方法。     

Al2O3p/2024Al基复合材料的界面结构

利用TEM、HRTEM等分析测试手段,对挤压铸造法制备的Al2O3颗粒增强2024Al基复合材料的界面组织结构进行了观察与分析。结果表明：Al2O3p/2024Al基复合材料的界面结合良好,未发现界面反应物,铝基体与Al2O3颗粒以共格关系结合,界面属直接结合型,且Al2O3颗粒与Al基体存在如下的位向关系：Al2O3（1^-1^-21^-）//Al（1^-1^-1^-）;Al2O3〈3^-41^-1^-〉//Al〈110〉。     

Al/TiO2复合粉的机械合金化

该研究旨在了解制备Ti(Al，O)，Al2O3和TixAly(O)/Al2O3复合材料工艺条件、显微组织、性能之间的关系，并开发出一种制备Ti3Al/TiAl粉的新工艺。     

Fe3Al纳米粒子增强Al2O3陶瓷的制备及性能

用热压烧结法制备了纳米Fe3 Al粒子增强Al2 O3 基复合材料。研究了 14 5 0～ 16 0 0℃不同烧结温度下纳米Fe3 Al的加入量与材料的致密度、力学性能及显微结构的关系。结果表明 :纳米Fe3 Al的加入可使Al2 O3 晶粒的生长受到抑制 ,使复合材料的烧结温度提高。Fe3 Al/Al2 O3 纳米复合材料有良好的力学性能 ,其抗弯强度最高可达832MPa ,断裂韧性最高可达 7.96MPa·m1/ 2 。     

Fe3Ai纳米粒子增强A12O3陶瓷的制备及性能

用热压烧结法制备了纳米Fe3Al粒子增强Al2O3基复合材料.研究了1 450～1 600 ℃不同烧结温度下纳米Fe3Al的加入量与材料的致密度、力学性能及显微结构的关系.结果表明纳米Fe3Al的加入可使Al2O3晶粒的生长受到抑制, 使复合材料的烧结温度提高.Fe3Al/Al2O3纳米复合材料有良好的力学性能, 其抗弯强度最高可达832 MPa, 断裂韧性最高可达7.96 MPa*m1/2.     

富Al2O3区域Al2O3-Na2O-CaO-SrO系固态反应的研究

用理学X射线衍射仪、TG-DTA、IR-440红外光谱研究了富Al2O3区域Al2O3-Na2O-CaO-SrO系的固态反应.煅烧过程固态反应的最终物相组成为Na2O·11Al2O3、CaO·6Al2O3、SrO·6Al2O3与α-Al2O3共存.     

Si复合Al2O3-SiC材料热机械性能的研究

通过应力-应变关系、高温抗折强度等高温试验，研究了金属硅复合Al2O3-SiC材料的热机械性能，结合SEM和XRD，对金属硅复合Al2O3-SiC材料高温显微结构和物相进行分析。结果表明：金属硅作为一个组元，不仅能缓解Al2O3-SiC材料由于热膨胀系数不匹配产生的内应力，而且使Al2O3-SiC材料兼具有金属塑性的特点，从而改善了Al2O3-SiC无机材料热机械性能。     

Si复合Al2O3-SiC材料热机械性能的研究

通过应力-应变关系、高温抗折强度等高温试验,研究了金属硅复合Al2O3-SiC材料的热机械性能,结合SEM和XRD,对金属硅复合Al2O3-SiC材料高温显微结构和物相进行分析.结果表明:金属硅作为一个组元,不仅能缓解Al2O3-SiC材料由于热膨胀系数不匹配产生的内应力,而且使Al2O3-SiC材料兼具有金属塑性的特点,从而改善了Al2O3-SiC无机材料热机械性能.     

原位生成Al2O3增强Al-4Mg基复合材料中的Al2O3/Al位向关系

综合搅拌铸造法和原位反应制备了Al2O3颗粒增强Al-4Mg基复合材料，并对制备的Al-4Mg基复合材料进行了透射电镜(TEM)观察分析，发现Al2O3／Al之间不存在固定的位向关系，但存在如下优先的位向关系：(1210)Al2O3∥(111)Al，[1012]Al2O3∥[112]Al，[2021]Al2O3∥[101]Al．     

X-ray diffraction study of Ba0.985Na0.015Ti0.985Nb0.015O3, Ba0.6Na0.4Ti0.6Nb0.4O3 and Ba0.3Na0.7Ti0.3Nb0.7O3 compositions

The Ba_0.985Na_0.015Ti_0.985Nb_0.015O₃, Ba_0.6Na_0.4Ti_0.6Nb_0.4O₃ and Ba_0.3Na_0.7Ti_0.3Nb_0.7O₃ compositions of the (1 − x) BaTiO₃–xNaNbO₃ (BTNNx) system have been studied by X-ray diffraction and by measurements of dielectric properties. The specimens with composition BTNN (x = 0.015, 0.40 and 0.70) have been refined by the JANA program from X-ray powder diffraction data. Ceramic samples with composition (1 − x) BaTiO₃ + xNaNbO₃ (where x = 0.015, 0.40 and 0.70) were prepared by calcinations from appropriate mixture of BaCO₃, TiO₂, Na₂CO₃ and Nb₂O₅. The calcined powder was sintered at temperature range 1200–1400 °C. As the composition x increased from 0.015 (and 0.70), the ferroelectric ceramics (x = 0.015, FE) with tetragonal phase changed to the ferroelectric relaxors (RFE, x = 0.40). RFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to 180 K) due to a frustration between RFE and FE state. These ceramics present the classical ferroelectric character when 0 ≤ x < 0.075 and 0.55 < x ≤ 1 and relaxor character when 0.075 ≤ x ≤ 0.55.     

Magnetic, electrical and plastic properties of Fe76Nb2Si13B9, Fe75Ag1Nb2Si13B9 and Fe75Cu1Nb2Si13B9 amorphous alloys

Influence of 1 h annealing in vacuum on magnetic, electrical and plastic properties of Fe₇₆Nb₂Si₁₃B₉, Fe₇₅Ag₁Nb₂Si₁₃B₉ and Fe₇₅Cu₁Nb₂Si₁₃B₉ melt spun ribbons were carefully investigated. It was shown that in all cases soft magnetic properties can be significantly enhanced by applying 1-h annealing at characteristic temperatures T_op. This optimization annealing causes that permeability increases more than 15-times and magnetic losses (tangent of loss angle) achieves a minimum in relation to the as quenched state. Using structural examinations (X-ray and HRTEM) it was shown that for the Fe₇₅Cu₁Nb₂Si₁₃B₉ alloy the optimized microstructure corresponds to a nanocrystalline αFe(Si) phase whereas in other alloys to a relaxed amorphous phase free of iron nanograins. As a consequence of this fact the Fe₇₆Nb₂Si₁₃B₉ and Fe₇₅Ag₁Nb₂Si₁₃B₉ alloys show higher plasticity in comparison to the nanocrystalline Fe₇₅Cu₁Nb₂Si₁₃B₉ alloy. Temperatures of the first stage of crystallization, and related diffusion parameters were determined using measurements of resistivity versus temperature with different heating rates.     

Fe2+-Ni2+-NH3-NH4+-C2O42-H2O体系的沉淀配合平衡热力学

针对草酸盐配位共沉淀热分解还原法制备超细铁镍合金粉过程中Fe2+-Ni2+-NH3-NH4+-C2O42--H2O体系的溶液平衡建立热力学分析模型,并根据模型进行相关计算,揭示反应体系中各物质随pH值、氨及草酸浓度的变化关系。结果表明:溶液中的Fe主要以[Fe(C2O4)n]2 2n络合物形式存在,而铁氨络合物含量很低。当氨含量较低时,溶液中的Ni主要以[Ni(C2O4)n]2 2n存在;氨含量较高时,在酸性条件下,溶液中的Ni主要以[Ni(C2O4)n]2 2n存在,在碱性条件下,则主要以[Ni(NH3)n]2+存在。低pH值下,Ni的沉淀率较Fe的高,而高pH值下,Ni的沉淀率则较Fe的低。     

Thermodynamics and phase diagrams in the binary systems Na2O-SiO2, Na2O-GeO2, Na2O-B2O3, Li2O-B2O3, CaO-B2O3, SrO-B2O3, and BaO-B2O3

We applied our model to the enthalpy of mixing data of the binary systems Na₂O-SiO₂, Na₂O-GeO₂, Na₂O-B₂O₃, Li₂O-B₂O₃, CaO-B₂O₃, SrO-B₂O₃, and BaO-B₂O₃. The most stable composition in the liquid, that is where the enthalpy of mixing is most negative, is with a metal-oxygen ratio of 4 to 3, for monovalent metals (Na and Li) and 3 to 4 for divalent metals (Ba and Ca) in liquid silicates or borates. The same applies to the CaO-SiO₂, CaO-Al₂O₃, PbO-B₂O₃, PbO-SiO₂, ZnO-B₂O₃, and ZnO-SiO₂ systems. The oxygen to metal ratio, its constant value in various types of systems, reflects and describes the structure of the liquid. Using the analyzed enthalpies of mixing data and the available phase diagrams, we calculated the enthalpies of formation of the various binary compounds. The results are in excellent agreement with data in the literature that were obtained from direct solid-solid calorimetry.     

New Zr6CoAs2-type compounds: Y6CoBi2, Ho6CoBi2 and Tm6CoBi2

Results of a powder X-ray diffraction investigation of new ternary compounds are reported. The compounds Y₆CoBi₂ [a=0.8312(1) nm, c=0.4144(1) nm], Ho₆CoBi₂ [a=0.8246(2) nm, c=0.4095(1) nm], and Tm₆CoBi₂ [a=0.8155(2) nm, c=0.4066(1) nm] crystallize in the hexagonal Zr₆CoAs₂-type structure (space group P6b2m No. 189). The Zr₆CoAs₂-type structure is a superstructure of the Fe₂P-type structure.     

Al2O3-Sm2O3-CeO2电解质的性能（英文）

采用溶胶-凝胶法和低温燃烧技术制备Ce1-xSmxO2（x=0,0.1,0.2,0.3）和掺杂Sm和（2%-8%）Al2O3的二氧化铈;研究其合成、结构、致密化、导电性和热膨胀等性能,并利用XRD研究其结构和相组成。结果表明,于1300°C烧结球团,获得致密的陶瓷,于1250°C在Ce0.8Sm0.2O0.2中加入2%和4%的Al2O3以促进烧结。利用扫描电子显微镜观察烧结后球团的表面形貌,使用双探针交流阻抗谱研究总离子电导率。     

Zur Kenntnis von RbBa3Ca4Cu3V7O28

Single crystals of RbBa₃Ca₄Cu₃V₇O₂₈ were prepared above the melting point of the reaction mixture. It crystallizes with hexagonal symmetry, space group C_6V⁴-P6₃mc, a 11.1751, c 12.434 Å, Z = 2. RbBa₃Ca₄Cu₃V₇O₂₈ is the second member of a new structure type of the copper-oxovanadates. Ba²⁺ shows an unusual 12-fold coordination. The two calcium positions are coordinated by trigonal prisms and octahedra respectively. The copper coordination is characterized by a stretched square pyramid. The Cu²⁺ ions are outside the centre nearly in plane of the pyramids.

Zusammenfassung

Einkristalle von RbBa₃Ca₄Cu₃V₇O₂₈ wurden oberhalb des Schmelzpunktes der Reaktionsmischung erhalten. Die Verbindung kristallisiert hexagonal, Raumgruppe C_6V⁴-P6₃mc, a 11.1751, c 12.434 Å, Z = 2. RbBa₃Ca₄Cu₃V₇O₂₈ ist das zweite Beispiel für einen neuen Strukturtyp der Kupfer-Oxovanadate, mit 12-fach koordinierten Ba²⁺ -Ionen. Die zwei Calciumpositionen sind trigonal prismatisch bzw. oktaedrisch koordiniert. Die Koordination der Cu²⁺-Ionen ist durch eine gestreckte Pyramide charakterisiert. Cu²⁺ ist auβerhalb des Polyederzentrums nahezu in der quadratischen Fläche der Pyramide angeordnet.     

电弧喷涂制备Fe65Cr20Mo7B3.5SiMn1.5W3涂层

在Q235低碳钢板上利用电弧喷涂工艺进行喷涂,以制得Fe65Cr20Mo7B3.5SiMn1.5W3涂层。喷涂材料为自行配制的丝材,按照35%的填充率将配好的粉填充到U型不锈钢外皮中,经过多道拉拔、挤压工艺制成Φ2mm的粉芯丝材。采用X射线衍射仪、扫描电镜、能谱分析仪、透射电镜对涂层的物相和组织形貌及成分进行了表征;采用差示扫描量热仪、显微硬度仪等设备对涂层的热稳定性及显微硬度进行了检测和分析。试验结果表明:涂层组织形貌呈典型的层状组织结构,由变形良好的带状粒子相互搭接堆积而成。涂层含有50.63%的非晶相,同时含有纳米级的晶相。涂层组织均匀、结构致密、孔隙率低,并且涂层硬度高达1040.5HV0.3,属硬质涂层,具有良好的热稳定性。     

Synthesis and electrochemical properties of LiNi0.4Mn1.5Cr0.1O4 and Li4Ti5O12

Spinel compound LiNi_0.4Mn_1.5Cr_0.1O₄ (LNMCO) and Li₄Ti₅O₁₂ (LTO) were synthesized by the sol-gel method and the solid-state method, respectively. The particle sizes of the products LiNi_0.4Mn_1.5Cr_0.1O₄ and Li₄Ti₅O₁₂ were 0.5 to 2 um and 0.5 to 0.8 um, respectively. All samples exhibited excellent electrochemical properties. A LiNi_0.4Mn_1.5Cr_0.1O₄/Li₄Ti₅O₁₂ (LNMCO/LTO) cell was fabricated and was demonstrated to exhibit good electrochemical properties at the high current rate of 1 C. When the specific capacity was determined based on the mass of the LNMCO cathode, the LNMCO/LTO cell delivered 125 mAh g⁻¹ at 1 C and 77 mAh g⁻¹ at 5 C. The capacity retentions after 30 cycles were 94.4 % and 83.1 %, respectively.