共查询到20条相似文献,搜索用时 109 毫秒
1.
韶钢第二轧钢厂于1996年3月开始采用板坯热送热装工艺,取得了明显效果。本文较全面地介绍了该工艺方案在韶钢三轧厂的提出、确定及应用情况。随着韶钢中板改造工程的完成,板坯热送热装工艺将发挥更大的作用。 相似文献
2.
3.
针对攀钢连铸板坯热送热装生产现状,开发了板坯热送,加热过程数学模型,进行了铸坯生产组织方式及表面质量状况轧制前后对应关系的工业试验,在此基础上,建立了铸坯热送热装管理办法和加热炉操作规程。生产统计表明,铸坯热送热装率从1995年的16.7%提高到1996年的36.9%平均入炉温度达565℃。 相似文献
4.
本文综述了连铸板坯热送热装和直接轧制工艺在国内外的现状和发展趋势,工结合公司七厂实行热送热装工艺提出了一些参考意见。 相似文献
5.
6.
连铸板坯热送热装及直接轧制工艺具有增产、节能、投资少和提高产品质量等优点。介绍了鞍钢第三炼钢厂大连铸板坯短流程在线直送热装;连铸与初轧板坯小批量穿插装炉;微机优化连铸坯加热工艺等方案的研究内容。该方案需要在大生产中不断完善,以提高其科研水平和经济技术指标。 相似文献
7.
8.
9.
10.
本文论述了连铸板坯热送热装的意义及其支撑技术,着重分析了邯钢热送热装的工艺状况并做出了相应的研究方案。 相似文献
11.
12.
ABSTRACTThe effect of high-temperature sintering (1180°C and 1250°C) on the dimensional stability, geometrical precision, density and microstructure of rings made of five different low alloy steels was studied. Density and dimensional shrinkage slightly increase with temperature, but the dimensional and the geometrical precision of parts, do not depend on sintering temperature. Sintering temperature maybe therefore increased up to 1250°C without impairing the dimensional and geometrical precision of the investigated rings. An estimation of the effect of the high sintering temperature on tensile properties is presented, based on the microstructure and on the fraction of the load-bearing section. A significant increase in both tensile strength and tensile ductility may be expected, in particular when the sintering temperature is increased up to 1250°C. 相似文献
13.
《钢铁研究学报(英文版)》2011,(Z1):615-620
The effects of technological parameters on microstructures and properties of low cost hot rolled dual-phase steel was researched by design different finish rolling temperature,mid cooling temperature between laminar cooling and UFC (ultra fast cooling) and stable UFC rate on the same gauge strips with the same chemistry composition during the manufacture process.It is the key for controlling coil temperature to control finish rolling temperature and mid cooling temperature between laminar cooling and UFC that based on stable UFC rate precondition.The lower finish rolling temperature,with mid cooling temperature between laminar cooling and UFC,the better to form martensite is.The foundation of developing the similar productions on the similar product line was supplied.It is good to technological advancement of developing high affixation value production as hot rolled DP steel,TRIP steel etc.in CSP line. 相似文献
14.
高铁闪锌矿低温低压浸出新工艺研究 总被引:6,自引:3,他引:6
在硫熔点温度以下对铁闪锌矿进行加压浸出试验研究,重点考察浸出温度、时间、矿物粒度、氧分压、初始酸度等因素对锌、铁浸出率的影响。结果表明,在115℃、氧分压500kPa下浸出3h,锌浸出率可以达到97%以上,溶液铁含量低于2g/L。 相似文献
15.
16.
为了进一步提升双相钢性能、探究Nb-V元素复合添加对双相钢组织性能的影响,在实验室研发了Nb-V微合金化的冷轧双相钢。利用连退模拟试验机、扫描电镜等设备,系统地研究了退火温度和过时效温度对双相钢组织性能的影响。结果表明,抗拉强度和伸长率随着退火温度的升高变化不大,屈服强度在组织中铁素体含量明显减少后有显著提升;Nb、V元素的添加细化了组织,可以提高综合性能。随着过时效温度的升高,试验钢主要组织由起初低温时的淬火马氏体+回火马氏体变为高温时的粒状贝氏体,残余奥氏体比例也逐渐增大。高温过时效时,试验钢强度的降低主要由回火马氏体的软化造成;低温过时效时,V析出量的增加也对试验钢的强化起到了重要作用。 相似文献
17.
分析得出C22.8高锰高铝钢初轧坯拉裂造成整罐钢绝废产生的原因。这种现象是钢锭装炉温度不合理所致。通过实验得出了该钢的最佳装炉温度。 相似文献
18.
19.
研究了不同加热温度、终锻温度对GH4169合金Φ130mm径锻棒材组织和性能的影响。结果表明,加热温度和终锻温度过低时,棒材心部虽然获得了细于ASTM11级的晶粒,但表面甚至R/2处会因变形温度低于动态再结晶温度而残留部分原始拉长晶粒;同时δ相大量析出,不利于合金的综合性能。加热温度和终锻温度过高时,因原始晶粒在加热过程中过分长大,在变形过程中难以全部完成动态再结晶而残留部分原始拉长晶粒;同时δ相显著减少,合金的高温综合性能显著下降。在合适的加热温度和终锻温度下,棒材心部获得了均匀的10级晶粒,同时边缘获得了完全再结晶的11级晶粒,各部位δ相差异较小且基本呈颗粒状和短棒状在晶界均匀弥散分布,合金具有良好的低温、高温综合性能。 相似文献