Fabrication and characterization of Ag–TiO2 multiphase nanocomposite thin films with enhanced photocatalytic activity

Ag–TiO₂ multiphase nanocomposite thin films were prepared on quartz substrates by the liquid phase deposition (LPD) method from a mixed aqueous solution of ammonium hexafluouotitanate, silver nitrate and boric acid under ambient temperature and atmosphere followed by calcination at 500 °C for 1 h. The grain growth of anatase was depressed upon Ag⁺ doping. However, silver ions not only promoted (or catalyzed) the formation of brookite phase but also reduced the phase transformation temperature of anatase to rutile. With increasing AgNO₃ concentration, the transmittance and band gap of the composite thin films decreased; however, the intensity of surface plasmon absorption (SPA) peaks increased and their peak position shifted to a longer wavelength range. When AgNO₃ concentration was higher than 0.03 M, the prepared samples consisted of anatase, brookite, rutile and metal silver nanocrystal particles, and their grain size ranges were 5–30 nm. The photocatalytic activity of the Ag–TiO₂ multiphase nanocrystal composite thin films prepared by this method exceeded that of pure TiO₂ thin films by a factor of more than 6.3 when AgNO₃ concentration was kept in the range of 0.03–0.05. This was attributed to the fact that there were many hetero-junctions, such as anatase/rutile, anatase/brookite, Ag/anatase, Ag/rutile and so on, existed in the Ag–TiO₂ multiphase nanocomposite films.     

Photocatalytic activity and OH radical formation on TiO2 in the relation to crystallinity

Two types of TiO₂ samples, ST-01 (Ishihara-Sangyo, Japan) and A11 precursor (Police, Poland), were heat-treated at 400–1000 °C and characterized by the phase composition, crystallite size and lattice strain. These TiO₂ samples were tested for methylene blue (MB) decomposition and OH radical formation. Through heating TiO₂ up to 700 °C for 1 h the single anatase phase was remained, which had improved crystallinity, large crystallite size and very small lattice strain. By extending the calcination time up to 2–5 h, the anatase phase partially transformed to rutile phase, much faster by A11 precursor than by ST-01. Transformation of anatase phase to rutile reduced the rate of methylene blue decomposition, although OH radical formation was the highest in the samples having around 9 mass% of rutile. However, methylene blue decomposition not only depended on OH radical formation on TiO₂ particles, but also the content of even small amount of rutile in TiO₂ reduces markedly the rate of methylene blue decomposition.     

Effect of promoters including tungsten and barium on the thermal stability of V2O5/sulfated TiO2 catalyst for NO reduction by NH3

The effect of tungsten and barium on the thermal stability of V₂O₅/TiO₂ catalyst for NO reduction by NH₃ was examined over a fixed bed flow reactor system. The activity of V₂O₅/sulfated TiO₂ catalyst gradually decreased with respect to the thermal aging time at 600 °C. The addition of tungsten to the catalyst surface significantly enhanced the thermal stability of V₂O₅ catalyst supported on sulfated TiO₂. On the basis of Raman and XRD measurements, the tungsten on the catalyst surface was identified as suppressing the progressive transformation of monomeric vanadyl species into crystalline V₂O₅ and of anatase into rutile phase of TiO₂. However, the NO removal activity of V₂O₅/sulfated TiO₂ catalyst including barium markedly decreased after a short aging time, 6 h at 600 °C. This may be due to the transformation of vanadium species to inactive V–O–Ba compound by the interaction with BaO which was formed by the decomposition of BaSO₄ on the catalyst surface at high reaction temperature of 600 °C. The addition of SO₂ to the feed gas stream could partly restore the NO removal activity of thermally aged V₂O₅/sulfated TiO₂ catalyst containing barium.     

Hydrogen sorption of magnesium hydride doped with nano-sized TiO2

Various phases of TiO₂ such as anatase, rutile and commercial P25 were added to magnesium hydride by high-energy ball milling in order to improve the hydriding properties of the magnesium. After 1 h milling, the sample containing nano-size rutile powder (200–400 nm) showed uniform distribution, while other shapes of TiO₂ added samples did in separate phase. The effect of the rutile concentrations (3, 5, 7 and 10 mol%) on the hydrogen sorption property of MgH₂ has been investigated and found that the sample containing 5 mol% rutile had the highest hydrogen capacity of 4.40 wt.% at 300 °C and 3.54 wt.% at 250 °C. This amount of hydrogen absorption is still lower than the pure magnesium requires a long activation time, however, its kinetics of hydrogen sorption was greatly enhanced. Moreover, hydrogen absorption capacity was slightly increased with the increase in number of cycles. The mechanism of catalytic effect of uniformly distributed TiO₂ and TiO₂ dispersed as discrete particles in magnesium matrix has been discussed based on microstructural observations.     

Synthesis of nanosized TiO2/SiO2 particles in the microemulsion and their photocatalytic activity on the decomposition of p-nitrophenol

Nanosized pure TiO₂ particles were prepared by hydrolysis of TTIP in the sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles. TiO₂/SiO₂ nanoparticles were also prepared from TEOS as a silicon source and TTIP as a titanium source. These particles were characterized by TEM, XRD, FT-IR, BET, TGA and DTA. From thermal analysis and XRD analysis, the anatase structure of pure titania appeared in the 300–600 °C calcination temperature range and the rutile structure was showed above 700 °C. However, no rutile phase was observed for the TiO₂/SiO₂ particles up to 800 °C. The crystallite size decreased and the surface area of TiO₂/SiO₂ particles monotonically increased with an increase of the silica content. From FT-IR analysis, the band for Ti–O–Si vibration was observed and the band intensity for Si–O–Si vibration increased with an increase of the silica content. The micrographs of TEM showed that the TiO₂/SiO₂ nanoparticles had a spherical and a narrow size distribution. In addition, TiO₂/SiO₂ particles showed higher photocatalytic activity than pure TiO₂ and the TiO₂/SiO₂ (90/10) particles showed the highest activity on the photocatalytic decomposition of p-nitrophenol.     

Development of the efficient TiO2 photocatalyst in photoassisted selective catalytic reduction of NO with NH3

Photoassisted selective catalytic reduction (photo-SCR) of NO with NH₃ in the presence of O₂ takes place at room temperature over TiO₂ photocatalyst. From the results of photo-SCR reaction over various TiO₂, we found that JRC-TIO-11 exhibited the best activity. The reaction activity correlated to the amount of acid sites of TiO₂, but did not depend on the specific surface area and crystal diameter. The mixture of rutile and anatase shows higher activity than any of the corresponding TiO₂ single phase catalyst.     

Local structure and photocatalytic activity of B2O3–SiO2/TiO2 ternary mixed oxides prepared by sol–gel method

The local structure and the photoactivity of B₂O₃–SiO₂/TiO₂ ternary mixed oxides (SiO₂ content was fixed as 30 at.% with respect to TiO₂) was investigated by using XRD, FT-IR, BET, UV-vis spectra, and electron paramagnetic resonance (EPR) measurement. In FT-IR analysis, boron was incorporated into the framework of titania matrix with replacing Ti---O---Si with Si---O---B or Ti---O---B bonds. Also, paramagnetic species such as O⁻ and Ti³⁺ defects were formed by the boron incorporation. In SiO₂/TiO₂ mixed oxides, a blue shift in the light absorption band was observed due to the quantization of band structure. All B₂O₃–SiO₂/TiO₂ samples had pure anatase phase and no rutile phase was formed even though the calcination temperature was over 900 °C. Incorporating boron oxides of more than 10% enlarges the grain size of anatase phase and causes a red shift of the light absorption spectrum. The surface area was monotonically decreased with increasing the content of boron content. As a result, the photoactivity of B₂O₃–SiO₂/TiO₂ ternary mixed oxides was greatly influenced by the content of boron oxide. The highest photoactivity (g moles/min l) was obtained when the boron content was 5% and seven times higher than that of silica/titania binary mixed oxide. In addition, the specific photoactivity (g moles/m² l) was maximum still at 5%. It was concluded that the large reduction of surface area, the change of band structure, and more formation of bulk Ti³⁺ sites are responsible for the deterioration in the photoactivity of B₂O₃–SiO₂/TiO₂ ternary mixed oxides when the content of boron is over 10%, although their crystallinity was enhanced by increasing the calcination temperature with keeping anatase phase.     

Hydroisomerization of n-heptane and dehydration of 2-propanol on bulk and supported WO2(Hx)ac on TiO2

Characterization by XPS–UPS and XRD of commercial bulk WO₂ enabled us to identify the presence of four to five layers of WO₃ on the sample surface with an equal amount of W⁵⁺, possibly W₂₀O₅₈ in the interface. The presence of these WO₃ and W₂₀O₅₈ on the WO₂ surface were not detected by XRD. Exposure of commercial bulk WO₂ to hydrogen at temperatures higher than 673 K results in the reduction of surface WO₃ to WO₂ and the formation of the bifunctional WO₂(H_x)_ac phase on its surface. A complete conversion of surface WO₃ to WO₂(H_x)_ac has been obtained following the exposure of the sample to hydrogen for at least 6 h at 773 K. A conversion of 52% of n-heptane at 573 K reaction temperature and a selectivity of 90% in isomerization products, mainly 2,3-MH and multibranched molecules were obtained. The isomerization products distribution is in agreement with the statistical and thermodynamic equilibrium of the methyl-shift mechanism. The stability of the active WO₂(H_x)_ac phase has been tested under prolonged exposure to hydrogen and the reaction mixture. Similar results were obtained in the case of bulk WO₃ and WO₃/TiO₂ systems. Dehydration and dehydrogenation of 2-propanol were studied on these systems at 393 K reaction temperature.     

SO2 resistant antimony promoted V2O5/TiO2 catalyst for NH3-SCR of NOx at low temperatures

To get the low temperature sulfur resistant V₂O₅/TiO₂ catalysts quantum chemical calculation study was carried out. After selecting suitable promoters (Se, Sb, Cu, S, B, Bi, Pb and P), respective metal promoted V₂O₅/TiO₂ catalysts were prepared by impregnation method and characterized by X-ray diffraction (XRD) and Brunner Emmett Teller surface area (BET-SA). Se, Sb, Cu, S promoted V₂O₅/TiO₂ catalysts showed high catalytic activity for NH₃ selective catalytic reduction (NH₃-SCR) of NO_x carried at temperatures between 150 and 400 °C. The conversion efficiency followed in the order of Se > Sb > S > V₂O₅/TiO₂ > Cu but Se was excluded because of its high vapor pressure. An optimal 2 wt% ‘Sb’ loading was found over V₂O₅/TiO₂ for maximum NO_x conversion, which also showed high resistance to SO₂ in presence of water when compared to other metal promoters. In situ electrical conductivity measurement was carried out for Sb(2%)/V₂O₅/TiO₂ and compared with commercial W(10%)V₂O₅/TiO₂ catalyst. High electrical conductivity difference (ΔG) for Sb(2%)/V₂O₅/TiO₂ catalyst with temperature was observed. SO₂ deactivation experiments were carried out for Sb(2%)/V₂O₅/TiO₂ and W(10%)/V₂O₅/TiO₂ at a temperature of 230 °C for 90 h, resulted Sb(2%)/V₂O₅/TiO₂ was efficient catalyst. BET-SA, X-ray photoelectron spectroscopy (XPS) and carbon, hydrogen, nitrogen and sulfur (CHNS) elemental analysis of spent catalysts well proved the presence of high ammonium sulfate salts over W(10%)/V₂O₅/TiO₂ than Sb(2%)/V₂O₅/TiO₂ catalyst.     

Dielectric behavior of Nb2O5-doped TiO2/epoxy thick films

TiO₂/epoxy composite thick films containing the TiO₂ powders doped with 4 and 10 vol% Nb₂O₅ heat treated under vacuum at 1050 and 1150 °C, were prepared by the screen printing and curing steps. The Nb₂O₅-doped TiO₂ ceramic bulks demonstrated a higher effective dielectric constant at different densification environments, as compared with pure TiO₂. The dielectric properties of the TiO₂/epoxy thick films were improved if the heat-treated 4 vol% Nb₂O₅-doped TiO₂ powder was incorporated instead of the un-doped and heat-treated 10 vol% Nb₂O₅-doped TiO₂ powders. The disadvantage of the doped TiO₂ having higher dielectric loss tangent could be minimized after its powder was properly treated and mixed with epoxy to form the TiO₂/epoxy composite. A best result with the dielectric constant of 23 and the loss tangent of 0.046 was obtained for the 40 vol% TiO₂/epoxy composite thick films, where the TiO₂ powder was doped with 4 vol% Nb₂O₅ followed by calcination at 1000 °C in air and heat treatment at 1150 °C under vacuum.     

The CO–H2 and CO–H2O reactions over TiO2 nanotubes filled with Pt metal nanoparticles

We have investigated the catalytic behavior of Pt encapsulated TiO₂ nanotubes for the water gas shift reaction as well as the hydrogenation of CO. Pt–TiO₂ nanotube catalysts were prepared by employing fine fiber shaped crystals of [Pt(NH₃)₄](HCO₃)₂ complex as a structure determining template material. The turnover frequencies (TOF) of these nanotube catalysts were more than one order of magnitude larger than conventional impregnation Pt/TiO₂ catalysts, and the selectivity for methanol in CO–H₂ reaction was extraordinary high compared to the impregnation catalysts. The XPS and XRD analyses of the nanotubes revealed characteristic electronic state of reduced TiO₂ (Ti³⁺ in rutile structure) with zerovalent Pt even after the calcination at 773 K. In WGS reaction, electron rich Ti³⁺ on the nanotube wall may play an important role to activate water molecules for the oxidation of CO. In CO–H₂ reaction, similar promotion effect of Ti³⁺ species may be operating for selective methanol formation by supplying active OH(a).     

On the modification of photocatalysts for improving visible light and UV degradation of gas-phase toluene over TiO2

The photocatalytic behavior of different TiO₂-based photocatalysts was reported for gas-phase toluene removal under both UV and visible light illumination, and compared to that of commercial P25 (Degussa) TiO₂. Promotion by sulfates and the use of nanosized anatase TiO₂ were reported to strongly increase the toluene removal efficiency under UV illumination. Nanosized-anatase was prepared by a protecting group sol–gel synthesis using hexamethyldisilazane as crystallite growth inhibitor. Sulfates played a double positive role, with photogenerated electrons transfer effects limiting charge recombination and as repulsive species for strongly adsorbed aromatic intermediates that act as poisons. The decrease in particle size obtained on nanosized anatase TiO₂ (5 nm) yielded a considerable enhancement in the toluene removal efficiency. Pure high surface area rutile has been synthesized at low temperature by a polyethylenglycol-containing sol–gel method for visible light activation purposes. A two-way semiconductor coupling phenomenon, consisting of a reciprocal electron/hole transfer between two visible light-activated oxides, rutile TiO₂ and WO₃, was proposed to explain the large gain in efficiency when adding low amounts of WO₃ to rutile TiO₂.     

Effect of substrate on the phase transformation of TiO2 in pearlescent pigment

The TiO₂/substrate pearlescent pigments were prepared by the hydrolysis of TiOCl₂ on the substrate followed by a calcinations process. The natural mica (muscovite), synthetic mica (fluorophlogopite) and -alumina flake were selected as the substrates for pearlescent pigments. The effect of substrate on the anatase to rutile (A–R) phase transformation of TiO₂ was studied. The A–R phase transformation of TiO₂ during the preparation of pearlescent pigments and their proportion in the TiO₂ layer have been analyzed by XRD measurements. The phase compositions of TiO₂ layer in each pearlescent pigment are quite different depending on the substrates. The TiO₂ layer deposited on -alumina has higher rutile fraction than those on the natural and synthetic mica. The XPS analysis showed that the cations originally present in the substrates diffused into the TiO₂ layer. The TiO₂ layer deposited on -alumina contains Al, while those on the natural and synthetic mica substrates contain Si and K in addition to Al. The metal cations diffusing from the substrate into TiO₂ layer might retard the A–R phase transformation of TiO₂. The suppressing effect on the A–R transformation of TiO₂ by mixed cations seems to be much stronger than that of single cation, resulting in relatively higher rutile fraction in the case of TiO₂ layer deposited on -alumina.     

Catalytic activity and solid acidity of vanadium oxide thin layer loaded on TiO2, ZrO2, and SnO2

Vanadium oxide spread highly on TiO₂ (anatase, A) and SnO₂, and rather densely on TiO₂ (rutile, R) and ZrO₂ to make the monolayer in less than 4–5 V nm⁻². Profile of acid site of the monolayer was measured by temperature programmed desorption of ammonia, and its relation with the surface oxidation state was studied. The acid site density was high on the V₂O₅/TiO₂ (A) independent of the degree of oxidation. On the other hand, that of V₂O₅/TiO₂ (R) and V₂O₅/ZrO₂ depended on the oxidation state, and the high value of the concentration was observed on the oxidized one. The strength of acid site generated on the V₂O₅ monolayer on TiO₂ was as high as on the HZSM-5 zeolite. Turnover frequency (TOF) of propane conversion, and product selectivity were measured in propane oxidation. Among tested oxides, the V₂O₅/TiO₂ (A) showed the high TOF and selectivity to form propylene, while those loaded on TiO₂ (R) and ZrO₂ the small TOF and poor selectivity. Therefore, the reaction profile of activity and selectivity could be related with the extent of spreading and solid acidity. An idea of limit of the acid site density ca. 1.5 nm⁻² on the monolayer was elucidated.     

Porous mullite–ZrO2 composites from reaction sintering of zircon and aluminum

Mullite–zirconia porous bodies were prepared by reaction sintering of zircon and alumina derived from oxidation reaction of Al at sintering temperatures between 1200 and 1600 °C. The results show that the incorporation of TiO₂ improves the oxidation reaction of Al, dissociation of zircon subsequently formation of mullite and zirconia. Composites containing TiO₂ obtain a high tetragonal concentration at 1500 °C, which reduces by increasing sintering temperature to 1600 °C. No tetragonal zirconia phase was detected at 1500 °C in TiO₂-free composites while tetragonal concentration was increased over this temperature. The major oxidation reaction of Al proceeds with a liquid–gas mechanism that is suitable for producing low dense ceramics. In spite of the higher porosity of the composites containing TiO₂, they possess almost the same flexural strength values as obtained from the TiO₂-free composites.     

Room temperature visible light oxidation of CO by high surface area rutile TiO2-supported metal photocatalyst

Visible light-active rutile TiO₂ with a high surface area of 200 m²/g was obtained by a low-temperature sol–gel synthesis, based on a long aging duration of a titania sol to stabilize the rutile phase. Decorated by an adequate amount of metallic nanoparticles, this non-doped TiO₂ displays high and stable performances for the on-stream room temperature oxidation of CO by visible light photocatalysis.     

V2O5-WO3-MoO3/TiO2催化剂用于NH3选择性还原减排NOx的性能（英文）

The V2O5-WO3-MoO3/TiO2 honeycomb catalyst was prepared with industrial grade chemicals. The structural and physico-chemical properties were analyzed with X-ray diffraction (XRD), scanning electron micrograph (SEM) and mercury porosimetry. The NOx conversion and durability were investigated on a pilot plant test set under the actual operational conditions of a coal fired boiler. The catalyst monolith had good formability with mass percentage of V:W:Mo:TiO2 :fiber glass= 1:4.5:4.5:72:18. Vanadium, tungsten and molybdenum species were highly dispersed on anatase TiO2 without causing the transformation of anatase TiO2 to rutile by calcining under a current of air at 450℃ for 4.5 h, but there were some degrees of crystal distortion. The catalyst particle sizes were almost uniform with close pile-up and the pore structure was regular with complete macro-pore formation and large specific surface area. The NOx conversion was sensitive to temperature but nearly insensitive to NH3 . The catalyst showed strong adaptability to NOx concentration with activity above 80% in the range of 615-1640 mg·m-3 . Within the range of 720-8640 h continuous operation, the NOx conversion dropped at a rate of about 1% reduction per 600 h.     

Photoactivity of anatase–rutile TiO2 nanocrystalline mixtures obtained by heat treatment of homogeneously precipitated anatase

Nanosized titanium dioxide photocatalysts with varying amount of anatase and rutile phases have been synthesized. Homogeneous precipitation of aqueous solutions containing TiOSO₄ with urea was used to prepare porous spherical clusters of anatase TiO_2. Photoactive titania powders with variable amount of anatase and rutile phases were prepared by heating of pure anatase in the temperatutre range 800–1150 °C. The structure evolution during heating of the starting anatase powders was studied by XRD analysis in overall temperature range of phase transformation. The morphology and microstucture characteristics were also obtained by HRTEM, BET and BJH. The spherical particle morphology of TiO₂ mixtures determined by SEM was stable in air up to 900 °C. The photocatalytic activity of the sample titania TIT85/825 heated to 825 °C in air, contained 77.4% anatase and 22.6% rutile was higher than that nanocrystalline anatase powder. Titania sample TIT85/825 reveals the highest catalytic activity during the photocatalyzed degradation of 4-chlorophenol in aqueous suspension.     

Formation of singlet molecular oxygen associated with the formation of superoxide radicals in aqueous suspensions of TiO2 photocatalysts

The production and decay of singlet molecular oxygen (¹O₂) in TiO₂ photocatalysis were investigated by monitoring its phosphorescence under various reaction conditions. First, the effects of additives such as KBr, KSCN, KI, H₂O₂, and ethanol on the amount of ¹O₂ produced by photo excitation of P25 TiO₂ were measured. The same additives were employed to investigate the effect on the amount of O₂⁻ produced. Comparison between the effects on ¹O₂ and O₂⁻ suggested that ¹O₂ is formed by the electron transfer mechanism, the reduction of molecular oxygens to O₂⁻ by photogenerated electrons and the subsequent oxidation of O₂⁻ to ¹O₂ by photogenerated holes. The formation of ¹O₂ decreased at pH < 5 and pH > 11, indicating that the intermediate O₂⁻ is stabilized at the terminal OH site of the TiO₂ surface in the pH range of 5 < pH < 11. Eighteen commercially available TiO₂ photocatalysts were compared on the formation of ¹O₂ and O₂⁻ in an aqueous suspension system. The formation of ¹O₂ was increased with decreasing size of TiO₂ particles, indicating that a large specific surface area causes a higher possibility of reduction producing O₂⁻ and then a large amount of ¹O₂ is formed. The difference in the crystal phase (rutile and anatase) did not affect the formation of ¹O₂.