Zn-TiO2纳米管的光催化活性

采用水热合成-浸渍法制备锌掺杂TiO2纳米管(Zn-TiO2纳米管),透射电镜照片显示Zn-TiO2纳米管为两端开口形貌均一的中空管状结构,管径约6～8 nm,壁厚约1 nm,长度约50～200 nm。研究了Zn-TiO2纳米管对甲基橙的光催化性能,结果表明:掺杂适量锌提高了TiO2纳米管对甲基橙的光催化降解性能,0.4%Zn-TiO2纳米管的光催化性能最佳。同时还探讨了Zn-TiO2纳米管用量和初始pH值等因素对光催化降解甲基橙的影响,结果显示Zn-TiO2纳米管能有效地降解甲基橙。随着光催化反应进行,CODCr去除率和脱色率变化规律不完全相同,可能是由于芳基和烷基降解速率不同所致。     

P掺杂TiO_2纳米管的制备及其对光催化甘油水溶液制氢性能的影响

以P掺杂的TiO2纳米颗粒为前驱体,采用水热合成法制备了系列P掺杂的TiO2纳米管.用N2吸附-脱附、透射电子显微镜(TEM)、X射线衍射(XRD)、激光拉曼光谱(Raman)、紫外可见漫反射(UV-Vis DRS)等方法对光催化材料的表面形貌、颗粒尺寸、孔结构、表面构造、吸光性能进行了分析.研究结果表明,所制备的各样品均为两端开口的纳米管形貌,管长为几十纳米到几百纳米,管外径约10 nm,内径约4 nm,管壁为多层;P掺杂后的系列TiO2纳米管仍保持锐钛矿晶型;掺杂的P可以进入到TiO2的骨架中,并形成P—O—Ti键,在TiO2禁带内引入杂质能级,降低了禁带能量,提高了TiO2的吸光性能及光生电子和空穴的分离性能.光催化甘油水溶液制氢活性评价表明,P掺杂的TiO2纳米管表现出了远高于纯TiO2管以及相同掺杂量的纳米颗粒的光催化制氢性能,2%P掺杂的样品在紫外灯和氙灯辐射下,其最高产氢速率可分别达1850μmol·(h·g)-1和335μmol·(h·g)-1.P掺杂TiO2样品光催化活性的提高与其禁带能量降低以及光生电子和空穴的分离性能增加有关.     

掺铅TiO2薄膜的光催化活性及电化学性能

采用溶胶凝胶烧结工艺在玻璃表面制备铅离子多层掺杂的光催化复合TiO2薄膜,用XRD技术表征了该薄膜的晶型,并用电化学方法测定了该薄膜电极的伏安特性及交流阻抗性能．以光催化降解甲基橙溶液为模型反应,采用两种不同方式制备的铅离子多层掺杂TiO2薄膜具有很好的光催化活性,最佳掺杂浓度均为0．5％(Pb／Ti原子百分比),PbD0.5掺铅薄膜的最佳光催化降解甲基橙表观速率常数约是纯TiO2的2．52倍．铅离子掺杂TiO2薄膜表现出近表面处捕获光生电子或空穴,随后被捕获的电子或空穴迁移到TiO2薄膜表向参与光催化反应。     

绢云母负载N掺杂纳米二氧化钛的制备及性能研究

以绢云母为载体,采用水解-沉淀法制备出了绢云母负载纳米TiO2粉体(TiO2/M),以尿素为氮源,采用后掺杂法制得具有可见光响应的N掺杂TiO2/M.采用XRD,XPS,SEM,DUV等手段对样品进行了性能表征;并以日光色镝灯为光源,甲基橙为模拟污染物检测其光催化活性.研究了N的掺杂对粉体中TiO2晶相结构,粒度和光催化性能的影响.结果表明,绢云母与TiO2通过桥氧相连形成包覆层,N的掺杂抑制了TiO2晶粒的长大,减缓锐钛矿向金红石相的转变,同时N的掺杂形成Ti—O—N键,形成新的能级结构,使样品对光的吸收边红移至440—550 nm,具有明显的可见光响应,对甲基橙的光催化降解率与没有掺N的样品相比,最高可达1.6倍.     

TiO2/粉煤灰的制备及光催化性能研究

以钛酸丁酯为原料,以粉煤灰微珠为载体,采用溶胶-凝胶法制备了TiO2/粉煤灰光催化剂.负载于粉煤灰表面的TiO2平均粒径约为7nm,晶型为锐钛矿型,该催化剂在太阳光下降解初始浓度为10mg·l-1的甲基橙,经6h,甲基橙的降解率可达98.9%,将其应用于实际样品的测定,经3h降解率可达96.1%,显示出优越的光催化降解性能.     

复合光催化剂(TiO2/多壁碳纳米管)制备工艺条件对甲基橙光催化降解动力学的影响

采用溶胶-凝胶法在不同条件下制备了多壁碳纳米管(MwCNTs)负载纳米TiO2的复合光催化剂(TiO2/MWCNTs).以偶氮类染料甲基橙为模拟污染物,研究不同制备工艺参数的复合光催化剂对甲基橙的光催化降解动力学的影响.对TiO2/MWCNTs的表征结果表明,纳米TiO2较好地分散在多壁碳纳米管表面;随着温度的升高,复...     

AgI/TiO2催化剂的焙烧处理及其可见光催化活性

常温下以TIO2为载体,使用沉积-沉淀法合成了具有不同AgI负载量的AgI/TiO2合光催化剂,并研究了焙烧处理对AgI/TiO2在可见光下(λ＞420nm)催化降解甲基橙(MO)的影响.结果表明,焙烧处理有效提高了AgI/TiO2的光催化性能,当焙烧温度高于200℃时,AgI/TiO2的光催化活性接近并达到最大值.当负载的AgI与TiO2的物质的量之比为0.15时,AgI%TiO2光催化降解MO的效率最高.XRD和UV-Vis测试表明焙烧处理提高了光敏组分AgI混晶中的γ相含量,拓宽了AgI/TiO2在可见光区的吸收范围,提高了光催化活性.     

TiO2光催化剂的超临界CO2萃取法制备及其降解甲基橙的活性

用超临界二氧化碳萃取TiO2醇凝胶制备纳米二氧化钛粉体，对萃取工艺条件进行了讨论，并用XRD，FT-IR，BET和DRS对上述粉体进行表征．以光催化降解甲基橙为模型反应，结果表明，与超临界二氧化碳干燥所得的粒子比较，该工艺干燥的TiO2粉体粒径小，比表面积大，光催化活性较高。     

掺Fe^3＋A-TiO2粉末的水热法制备及其光催化降解甲基橙

以硫酸钛为原料用水热法制备了掺Fe^3＋TiO2粉末,用SEM和XRD测定了样品的形貌和晶型,研究了以自制的掺Fe^3＋A-TiO2对甲基橙溶液的光催化降解作用。结果表明：所制备的TiO2为锐钛矿型TiO2即A-TiO2。365nm紫外光照射下,用自制的掺Fe^3＋A-TiO2降解甲基橙溶液的最佳条件是：10mg·L^-1的甲基橙溶液中加入0.050g掺5%Fe^3＋（物质的量比）A-TiO2粉末,用HNO3调节溶液成酸性后,18℃恒温反应4h,降解率达到57.8%。     

油酸铵改性的高活性TiO2/V-TiO2复合光催化剂的制备及光催化降解甲基橙的研究

采用溶胶-凝胶法,将经过油酸铵改性的掺钒二氧化钛粉末投入到纯TiO2溶胶中,烘干、煅烧,制得带有n-n异质结半导体结构的复合型高活性掺钒二氧化钛光催化剂,并通过XRD、TEM、XPS等技术对样品进行了表征。通过对甲基橙溶液的光催化降解实验来考察TiO2/V-TiO2催化剂的光催化活性。结果表明：TiO2/V-TiO2复合催化剂拥有比纯TiO2更高的光催化活性。其中,V的掺杂摩尔分数为0.5%、TiO2：V-TiO2的质量比为10∶1的最佳复合催化剂,其光催化活性是纯TiO2的5.1倍。     

TiO2纳米管光催化还原Cr（Ⅵ）的研究

以水热法制备TiO2纳米管,采用X射线衍射仪(XRD),高分辨透射电子显微镜(HRTEM)和紫外可见漫反射光谱对其结构和性质进行了表征.研究了光催化还原溶液中Cr(Ⅵ)的反应活性,分别考察了煅烧温度、反应溶液的pH、助催化剂对TiO2纳米管光催化还原的影响.实验结果表明,TiO2-550光催化活性最优;酸性条件有利于Cr(Ⅵ)的还原;NiO和Co2O3复合的TiO2-550光催化活性明显提高.     

Effect of metal ion-doping on characteristics and photocatalytic activity of TiO2 nanotubes for removal of humic acid from water

The effect of ion-doping on TiO₂ nanotubes were investigated to obtain the optimal TiO₂ nanotubes for the effective decomposition of humic acids (HA) through O₃/UV/ion-doped TiO₂ process. The experimental results show that changing the calcination temperature, which changed the weight fractions of the anatase phase, the average crystallite sizes, the Brunauer-Emmett-Teller surface area, and the energy band gap of the catalyst, affected the photocatalytic activity of the catalyst. The ionic radius, valence state, and configuration of the dopant also affected the photocatalytic activity. The photocatalytic activities of the catalysts on HA removal increased when Ag⁺, Al³⁺, Cu²⁺, Fe³⁺, V⁵⁺, and Zn²⁺ were doped into the TiO₂ nanotubes, whereas such activities decreased as a result of Mn²⁺- and Ni²⁺-doping. In the presence of 1.0 at.% Fe³⁺-doped TiO₂ nanotubes calcined at 550°C, the removal efficiency of HA was 80% with a pseudo-first-order rate constant of 0.158 min⁻¹. Fe³⁺ in TiO₂ could increase the generation of ·OH, which could remove HA. However, Fe³⁺ in water cannot function as a shallow trapping site for electrons or holes.     

Solar photocatalytic decomposition of two azo dyes on multi-walled carbon nanotubes (MWCNTs)/TiO<Subscript>2</Subscript> composites

Multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and UV-vis absorption spectra. Compared to pure TiO₂, the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region. The photocatalytic performances of the MWCNTs/TiO₂ composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G (K-6G) and Mordant black 7 (MB 7) azo dyes solution under solar light irradiation. The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO₂ for the degradation of azo dyes K-6G and MB 7. The effect of MWCNTs content, catalyst dosage, pH, and initial dye concentration were examined as operational parameters. The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law. The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%. A plausible mechanism is also proposed and discussed on the basis of experimental results.     

Photocatalytic degradation of methyl orange using ZnO nanorods

Nanosized ZnO rods were synthesized using a microwave-assisted aqueous method. High molecular weight polyvinyl alcohol was used as a stabilizing agent. Size, surface morphology, and structure were investigated using transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). SEM and TEM images show that ZnO nanorods have diameters of about 50?nm and lengths of a few micrometers. The XRD pattern reveals that ZnO nanorods are of hexagonal wurtzite structure. The average crystallite size calculated from Scherrer's relation was found to be 40?nm. The effects of catalyst loading, pH value, and initial concentration of methyl orange on the photocatalytic degradation efficiency using ZnO nanorods as photocatalyst were discussed. The results revealed that ZnO nanorods with a diameter of 50?nm showed the highest photocatalytic activity at a surface density of 0.2?g?dm^?3.     

静脉注射多壁碳纳米管后大鼠脏器的病理学观察(Pathological Observations of Rat Tissues After Intravenous Injection of Mutil-Wall Carbon Nanotubes)

以Wistar大白鼠为研究对象,观察了多壁碳纳米管(MWNTs)体内暴露后脏器的病理学变化.采用尾静脉注射的方法将直径为40～60nm的多壁碳纳米管(40～60MWNTs)和直径小于10nm的多壁碳纳米管(10MWNTs)暴露于大白鼠体内,同时分别采用纳米二氧化硅(SiO2)和乙炔碳黑(Cb)作为阳性和阴性对照.实验结果表明:1、3、5mg·kg-1(以大鼠体重计)多壁碳纳米管进入大鼠体内90d后,大鼠心脏、肾脏、肝脏和胃结构正常,未见明显的病理损伤.但是多壁碳纳米管均可在大鼠肺部沉积,随着暴露时间的延长,多壁碳纳米管一部分被肺巨噬细胞清除体外,但是残余的多壁碳纳米管引起了肺部的病理学改变.     

Carbon nanotubes and Cu–Zn nanoparticles synthesis using hyperaccumulator plants

This article reports a novel way to synthesize carbon nanotubes and Cu/ZnO nanoparticles using metal hyperaccumulator plants. Metal hyperaccumulator plants are traditionally used for phytoremediation to clean soil polluted by toxic metals. However, the transfer of toxic metals in plant shoots and leaves is an environmental issue because animals and other living organisms feeding on plants will transfer the metals to the ecosystem. Therefore, we suggest that hyperaccumulator plants could be used to synthesize nanoparticles. Here, Brassica juncea L., a Cu-hyperaccumulator plant, was collected around a copper mine and used as a raw chemical to produce carbon nanotubes and Cu/ZnO nanoparticles. The chlorophyll in shoots of B. juncea plants was ethanol extracted to yield chlorophyllin. Cu and Zn were extracted by HNO₃ to form Cu/Zn(NO₃)₂. The chlorophyllin reacted with Cu/Zn(NO₃)₂ to form Cu/Zn chlorophyllin. Cu/ZnO nanoparticles were synthesized by direct precipitation of Cu/Zn chlorophyllin with NaOH and ethanol. The vascular bundles in B. juncea plants, which have been purified and carbonized by HNO₃, were rapidly heated to about 400°C and then they were cooled to room temperature to obtain carbon nanotubes. Results indicate that the outer diameter of carbon nanotubes was around 80 nm. Cu/ZnO nanoparticles have a Cu_0.05Zn_0.95O composition, and had a diameter of about 97 nm. Our study not only inspires the search for a new strategy on the synthesis of nanostructure from renewable natural products, but also breaks through the traditional and limited ideas about the reuse of metals by hyperaccumulator plants.     

Photocatalytic degradation of phosphamidon using Ag-doped ZnO nanorods

The photocatalytic degradation of the organo-phosphorous pesticide phosphamidon at low concentration in aqueous solution on Ag-doped ZnO nanorods was investigated. Nanosized Ag-doped ZnO rods were synthesized by using a microwave assisted aqueous method. High molecular weight polyvinyl alcohol was used as a stabilizing agent. Composition and structure were investigated using energy-dispersive X-ray spectroscopy (EDAX) and X-ray diffraction (XRD). The XRD pattern reveals that ZnO nanorods are of hexagonal wurtzite structure. The average crystallite size calculated from Scherrer's relation was found to be 30?nm. The effects of catalyst loading, pH value, and initial concentration of phosphamidon on the photocatalytic degradation efficiency using Ag-doped ZnO nanorods as a photocatalyst have been discussed. The results revealed that Ag-doped ZnO nanorods with a diameter of 30?nm showed highest photocatalytic activity at a surface density of 1?g?dm^?3. The catalyst doped with 0.2?mol% Ag is effective for the degradation of phosphamidon with visible light. This opens a new possibility to decompose pesticides that are present in wastewater.     

ZnO纳米丛的制备及其光催化性能研究

以沉淀法制备了高活性ZnO纳米丛(nanobushes,ZNB),以水热反应制备得到普通ZnO纳米颗粒(nanoparticles,ZNP).利用X射线衍射仪(XRD)、透射电镜(TEM)、扫描电镜(SEM)、比表面积测定仪(BET)和光致发光光谱(PL)等手段对ZNB和ZNP进行了表征,并比较了其光催化活性的差异.在紫外光(λ≤387 nm)照射40 min后ZNB使有机染料罗丹明B(Rhodamine B,RhB)完全褪色,而相同条件下ZNP仅能使RhB褪色53%.通过总有机碳(TOC)的测定,研究了ZnO对RhB深度氧化矿化程度,光照6 h后ZNB对RhB矿化率高达92%,而ZNP对RhB的矿化率只有77%.跟踪测定了光催化降解过程中活性氧化物种相对含量的变化,表明紫外光激发条件下,ZnO光催化反应机理主要涉及羟基自由基(.OH)历程,且ZNB产生活性氧化物种的量高于ZNP.