N-type silk fibroin/TiO2 nanocomposite transparent films: electrical and optical properties

This paper highlights the effect of different concentrations of titanium dioxide (TiO₂) nanoparticles on the electrical and optical properties of silk fibroin (SF). TiO₂ based SF nanocomposite films were prepared using the solvent casting method. Uniform dispersion and agglomeration of nanoparticles, in nanocomposite films, were observed by field emission SEM. The conductivity of pure SF and nanocomposite films was determined by a four-point probe and the TiO₂ nanoparticles were found to bring high conductivity to the nanocomposite films. Dielectric strength improved with the addition of nanoparticles to the SF matrix. Dielectric constant and capacitance of the pure SF and nanocomposite films were measured using an LCR meter, which showed a 10-fold enhancement on the addition of nanoparticles in SF. A very unusual property, i.e. negative resistance, was observed during LCR meter analysis for the nanocomposite films for a particular range of frequency (200–550 kHz), voltage (1 V) and current (0.5–1.5 μA). TiO₂ nanoparticles changed the semiconducting behavior of the SF films from p-type to n-type as measured by the Hall effect experiment. The optical properties of pure SF and nanocomposite films were measured using a UV–visible spectrophotometer. The increased concentration of nanoparticles in the SF has effectively enhanced the absorbing coefficient, refractive index and percentage transmittance and reduced the bandgap energy. These SF/TiO₂ nanocomposite films have shown the potential to be used as dielectric and high refractive index material for optoelectronics applications. © 2021 Society of Industrial Chemistry.     

Preparation and characterization of high refractive index thin films of TiO2/epoxy resin nanocomposites

By using sol–gel method, amorphous titania was introduced into epoxy matrix to prepare a series of high refractive index TiO₂/epoxy resin nanocomposite films. To increase the refractive index of the hybrid films, triethoxysilane‐capped trimercaptothioethylamine (TCTMTEA), a new kind of high refractive index coupling agent was synthesized from trimercaptothioethylamine (TMTEA). In the experiment, TCTMTEA acted as the solidification agent together with TMTEA except being used as the coupling agent. The hybrid films have been characterized via FTIR, AFM, DSC, TGA, etc. The experimental results showed that the amorphous TiO₂ had been dispersed uniformly in the organic polymer matrix with the size smaller than 100 nm in each sample. More importantly, the refractive index of this kind of materials can be continuously adjusted from 1.61 to 1.797 with the content of TiO₂ increasing from 0% to 65% in mass, and the continuously adjusted refractive index is very important for the applications in optical antirefractive films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1631–1636, 2006     

Electrochemical synthesis and In situ spectroelectrochemistry of conducting NMPy‐TiO2 and ZnO polymer nanocomposites for Li secondary battery applications

Poly(N‐methylpyrrole) (PNMPy), poly(N‐methylpyrrole‐TiO₂) (PNMPy‐TiO₂), and poly (N‐methylpyrrole‐ZnO) (PNMPy‐ZnO) nanocomposites were synthesized by in situ electropolymerization for cathode active material of lithium secondary batteries. The charge–discharging behavior of a Li/LiClO₄/PNMPy battery was studied and compared with Li/LiClO₄/PNMPy‐nanocomposite batteries. The nanocomposites and PNMPy films were characterized by cyclic voltammetry, in situ resistivity measurements, in situ UV–visible, and Fourier transform infra‐red (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The differences between redox couples (ΔE) were obtained for polymer nanocomposites and PNMPy films. During redox scan, a negative shift of potential was observed for polymer nanocomposite films. Significant differences from in situ resistivity of nanocomposites and PNMPy films were obtained. The in situ UV–visible spectra for PNMPy and polymer nanocomposite films show the intermediate spectroscopic behavior between polymer nanocomposites and PNMPy films. The FTIR peaks of polymer nanocomposite films were found to shift to higher wavelengths in PNMPy films. The SEM and TEM micrographs of nanocomposite films show the presence of nanoparticle in PNMPy backbone clearly. The result suggests that the inorganic semiconductor particles were incorporated in organic conducting PNMPy, which consequently modifies the properties and morphology of the film significantly. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41526.     

Novel nanocomposite based on poly (xanthoneamide-triazole-ethercalix) and TiO2 nanoparticles: preparation,characterization, and investigation of nanocomposite capability in removal of cationic water pollutants

A new multifunctional nanocomposite based on poly (xanthoneamide-triazole-ethercalix) (PXTE) and TiO₂ nanoparticles (PXTE–TiO₂), which is a novel class of multiphase material containing nanosized inorganic material within polymer matrix, was prepared and characterized fully in this article. At first, PXTE was synthesized through click reaction, and then PXTE–TiO₂ nanocomposite was prepared by chemical immobilization of PXTE onto the modified TiO₂ nanoparticles. Nuclear magnetic resonance, Fourier transform infrared, X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, and thermal gravimetric analysis were applied for characterization of synthesized materials. Dye and ion removal capability of PXTE–TiO₂ nanocomposite were investigated by batch method for methylene blue and cadmium ion. The results showed that thermal stability and potential applicability of PXTE–TiO₂ nanocomposite make it as a good candidate for wastewater refinement.     

The synthesis and morphology characteristic study of BAO-ODPA polyimide/TiO2 nano hybrid films

Hybrid nanocomposite films of titanium dioxide (TiO₂) in polyimide (PI) from 2,5-bis(4-aminophenyl)-1,3,4-oxadiazole (BAO) and 4,4′-oxydiphthalic anhydride (ODPA) have been successfully fabricated by an in situ sol-gel process. These nanocomposite films exhibit fair good optical transparency up to 40 wt% of TiO₂ content. X-ray diffraction spectroscopy shows three sharp peaks in pure BAO-ODPA PI. It results from the intermolecular regularity. However, the intermolecular regularity in the hybrid film is disrupted by the introduction of TiO₂ nanoparticles with no sharp peak in XRD spectra. Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) results confirm the formation of TiO₂ particles in PI matrix. The surface Ti content is much lower than the theoretical bulk content in all hybrid films. The ratio of the former to the latter increases with the TiO₂ content and levels off at TiO₂ wt%≥20. Transmission electron microscope (TEM) images show that the TiO₂ phase is well dispersed in the polymer matrix. The size of the TiO₂ phase increases from 10 to 40 nm when the TiO₂ content is 5-30 wt%, respectively.     

Dynamic mechanical analysis and broadband electromagnetic interference shielding characteristics of poly (vinyl alcohol)-poly (4-styrenesulfonic acid)-titanium dioxide nanoparticles based tertiary nanocomposites

ABSTRACT

Novel tertiary nanocomposite films comprising of poly (vinyl alcohol) (PVA), poly (4-styrenesulfonic acid) (PSSA) and titanium dioxide (TiO₂) nanoparticles (NP_S) were prepared using simple solvent casting method. The structural, thermal, morphological, thermo-mechanical and electromagnetic interference (EMI) shielding properties of PVA/PSSA/TiO₂ nanocomposite films were investigated. The EMI shielding effectiveness (SE) of PVA/PSSA/TiO₂ nanocomposite films in the X and Ku band was found to be 12 dB and 13 dB respectively at 25 wt% TiO₂ NPs loading. These results demonstrate the possible applications of PVA/PSSA/TiO₂ nanocomposite films as low cost, lightweight and flexible material for EMI shielding.     

The TiO2–Clay-LDPE Nanocomposite Packaging Films: Investigation on the Structure and Physicomechanical Properties

The role of nanoclays and TiO₂ nanoparticle loadings were investigated on low density polyethylene crystalline structure, in addition to studying packaging film properties such as barrier, thermal and mechanical properties. The polymer crystal study indicated for the orthorhombic crystal phase and about 20% lower degree of crystallinity for nanocomposites containing more than 2 wt.% TiO₂ nanoparticles. Based on the X-ray diffraction technique, the dispersion of nanoclays was improved to almost good degree of clay exfoliation with the company of 4 wt.% TiO₂ nanoparticles. In agreement with XRD results, the TEM morphological studies mainly suggest that TiO₂ has a helpful effect on nanoclay exfoliation. The increase in degradation temperature of nanocomposites may be attributed to the formation of inorganic char on polymer melt. The barrier properties of TiO₂/clay nanocomposite packaging films depend mainly on nanoclay loading with an unclear trend from TiO₂ nanoparticles. The increase in elastic modulus and the yield stress of nanocomposite films showed great effects on film mechanical properties by nanoclays.     

Fabrication of a New Polyimide/Titania (TiO2) Nanocomposite Thin Film by the Sol-Gel Route

Polyimide/titania nanocomposite (PI/TiO₂ NC) was successfully fabricated through the in situ formation of TiO₂ within a PI matrix by the sol-gel process. FT-IR and XRD results confirmed the formations of the TiO₂ in the PI matrix. Transmission electron microscopy of the NC10% showed that the TiO₂ phase was well dispersed in the polymer matrix. The mechanical properties of the NC films were increased and elongation at break decreased with increasing TiO₂ content. Thermogravimetric analysis results revealed that the decomposition temperature of hybrid materials was increased with an increase in the content of TiO₂ nanoparticles within the NC films.     

Development of optically transparent ZnS/poly(vinylpyrrolidone) nanocomposite films with high refractive indices and high Abbe numbers

A series of optically transparent ZnS‐poly(vinylpyrrolidone) (PVP) nanocomposite films with high refractive indices and high Abbe numbers have been prepared. Mercaptoethanol (ME) capped ZnS nanoparticles (NPs) were introduced into the PVP polymer matrix via simple blending with high nanophase contents. ME‐ZnS NPs of around 3 nm were prepared from zinc acetate and thiourea precursors in N,N‐dimethylformamide using ME as a capping agent. Transparent nanocomposite films with high refractive indices and high Abbe numbers can be easily prepared by a conventional film casting method. TGA results indicated that the ZnS/PVP nanocomposite films exhibit good thermal stability and the measured contents of ZnS NPs in the films agree well with the theoretical values. The refractive indices and the Abbe numbers of the ZnS/PVP nanocomposite films range from 1.5061 to 1.7523 and 55.6 to 20.4 with the content of ME‐ZnS NPs varied between 0 and 80 wt %, respectively. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of amorphous silica nanoparticles and polymer blend compositions on the structural,thermal and dielectric properties of PEO–PMMA blend based polymer nanocomposites

The polymer nanocomposite (PNC) films consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend matrices dispersed with nanoparticles of amorphous silica (SiO₂) have been prepared by solution-cast method followed by melt-press technique. Effects of SiO₂ concentration (x?=?0, 1, 3 and 5 wt%) and PEO–PMMA blend compositional ratios (PEO:PMMA?=?75:25, 50:50, and 25:75 wt%) on the surface morphology, crystalline phase, polymer-polymer and polymer-nanoparticle interactions, melting phase transition temperature, dielectric permittivity, electrical conductivity, electric modulus and the impedance properties of the PNC films have been investigated. The crystalline phase of the PNC films decreases with the increase of PMMA contents which also vary anomalously with the increase of SiO₂ concentration in the films. The melting phase transition temperature and polymer-nanoparticle interactions significantly change with the variation in the compositional ratio of the blend polymers in the PNC films. It is observed that the effect of SiO₂ on the dielectric and electrical properties of these PNCs vary greatly with change in the compositional ratio of PEO and PMMA in the blends. The dielectric relaxation process of these films confirm that the polymers cooperative chain segmental dynamics becomes significantly slow when merely 1 wt% SiO₂ nanoparticles are dispersed in the polymer blend matrix.     

Efficient preparation of hybrid nanocomposite coatings based on poly(vinyl alcohol) and silane coupling agent modified TiO2 nanoparticles

In the present investigation, at first, the surface of titanium dioxide (TiO₂) nanoparticles was modified with γ-aminopropyltriethoxy silane as a coupling agent. Then a new kind of poly(vinyl alcohol)/titanium dioxide (PVA/TiO₂) nanocomposites coating with different modified TiO₂ loading were prepared under ultrasonic irradiation process. Finally, these nanocomposites coating were used for fabrication of PVA/TiO₂ films via solution casting method. The resulting nanocomposites were fully characterized by Fourier transform infrared spectroscopy (FT-IR), powder X-ray diffraction (XRD), thermogravimetric analysis/derivative thermal gravimetric (TGA/DTG), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The TEM and SEM results indicated that the surface modified nanoparticles were dispersed homogeneously in PVA matrix on nanoscale and based on obtained results a possible mechanism was proposed for ultrasonic induced nanocomposite fabrication. TGA confirmed that the heat stability of the nanocomposite was improved. UV–vis spectroscopy was employed to evaluate the absorbance and transmittance behavior of the PVA/TiO₂ nanocomposite films in the wavelength range of 200–800 nm. The results showed that this type of films could be used as a coating to shield against UV light.     

Preparation and characterization of UV‐curable ZnO/polymer nanocomposite films

A series of novel nano‐ZnO/polymer composite films with different ZnO contents was prepared through incorporation of pre‐made colloidal ZnO particles into monomer mixtures of urethane‐methacrylate oligomer and 2‐hydroxyethyl methacrylate, followed by ultraviolet (UV) radiation‐initiated polymerization. The colloidal ZnO nanoparticles with a diameter of 3–5 nm were synthesized from zinc acetate and lithium hydroxide in ethanol via a wet chemical method. In order to stabilize and immobilize the ZnO particles into the polymer matrix, the ZnO nanoparticles were further capped using 3‐(trimethoxysilyl)propyl methacrylate. Thermogravimetric analyses show that the ZnO nanoparticles were successfully incorporated into the polymer matrix and these ZnO/polymer composites have a good thermal stability. Transmission electron microscopy studies indicate the ZnO nanoparticles were uniformly dispersed in the polymer and they remained at the original size (3–5 nm) before immobilization. All nanocomposite films with ZnO particle contents from 1 to 15 wt% show good transparency in the visible region and luminescent properties. In addition, composite films with high ZnO content (>7 wt%) are able to absorb UV irradiation below 350 nm, indicating that these composite films exhibit good UV screening effects. Copyright © 2006 Society of Chemical Industry     

Application of paraffin and silver coated titania nanoparticles in polyethylene nanocomposite food packaging films

In this work, 3% and 5% TiO₂/Ag nanoparticles were dispersed in low‐density polyethylene through melt blending process, and subsequently nanocomposite films were prepared by hot pressing. Paraffin was used for the first time in this work as compatibilizer agent. The effect of TiO₂/Ag nanoparticle content, as well as compatibilizer dosage on the antimicrobial, morphological, mechanical, and optical performance of the nanocomposite films was investigated. Improved mechanical properties of the nanocomposite films were found on using paraffin as compatibilizer in comparison with the neat low‐density polyethylene (LDPE) films. The optical study results also showed that the addition of TiO₂/Ag to the LDPE films does not drastically change the film appearance other than making them more reddish. The fabricated nanocomposites presented in this study could be a suitable choice for food packaging (subject to further investigation of the food packaging behavior). The results showed that both TiO₂/Ag nanoparticle and compatibilizer are needed to prevent the bacteria growth in the film. The best result was obtained by using 5% nanoparticle and 4% paraffin compatibilizer where the bacteria growth rate was significantly reduced by 95%. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45913.     

Synthesis,characterization, optical,and dielectric properties of polyvinyl chloride/cadmium oxide nanocomposite films

Nano‐sized cadmium oxide (CdO) was synthesized using a sol–gel method and mixed with poly(vinyl chloride) (PVC). X‐ray diffraction and high‐resolution transmission electron microscopy measurements indicated that the average particle size of the CdO is about 70.18 nm. Scanning electron microscopy images revealed a good dispersion of CdO nanoparticles on the surface of the PVC films. The optical energy band gap (E_g) showed a decrease from 5.08 to 4.88 eV with increasing the CdO content. The refractive index dispersion of the nanocomposite films was found to obey the single oscillator model. The dispersion parameters were changed by CdO incorporation. According to the frequency and temperature dependence of the dielectric constant (ε′), the observed α_a‐relaxation peaks were assigned to the micro‐Brownian motion of the polymer main chains. The influence of CdO nanoparticles content on the ac conductivity and the activation energy of PVC nanocomposite films were discussed. It was found that both dielectric and optical properties were reinforced by the adding of CdO nanoparticles to the PVC matrix. Finally, the results of the present system are compared with those of similar materials. POLYM. COMPOS., 35:1842–1851, 2014. © 2014 Society of Plastics Engineers     

Electrochemical synthesis and in situ spectroelectrochemistry of conducting polymer nanocomposites. I. polyaniline/TiO2, polyaniline/ZnO,and polyaniline/TiO2+ZnO

The polyaniline (PAn), polyaniline/titanium dioxide (PAn/TiO₂), polyaniline/zinc oxide (PAn/ZnO), and a novel conducting polymer nanocomposites, polyaniline/titanium dioxide + zinc oxide (PAn/TiO₂+ZnO), were synthesized by in situ electropolymerization and potential cycling on gold electrode. The PAn and nanocomposite films were characterized by cyclic voltammetry, Fourier transform infra‐red (FTIR) spectroscopy, in situ resistivity measurements, in situ UV–Visible, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The differences between cathodic and anodic peaks of three redox couples were obtained for PAn and polymeric nanocomposite films. During cathodic and anodic scans, the shift of potential was observed for polymer nanocomposite films. The characteristic FTIR peaks of PAn were found to shift to lower wavelengthsin polymer nanocomposite films. These observed effects have been attributed to interaction of TiO₂, ZnO, and TiO₂+ZnO particles with PAn molecular chains. Significant differences from in situ resistivity of PAn and nanocomposite films were obtained. The resistance of PAn/TiO₂, PAn/ZnO, and PAn/TiO₂+ZnO films were found to be smaller than the PAn film. The in situ UV–Visible spectra for Pan and polymer nanocomposite films were studied. The results show the intermediate spectroscopic properties between PAn and polymer nanocomposite films. The morphological analyses of PAn and nanocomposite films have been investigated. The nanocomposites SEM and TEM micrographs suggest that the inorganic semiconductor particles were incorporated in organic conducting polymer, which consequently modifies the morphology of the films significantly. POLYM. COMPOS., 35:351–363, 2014. © 2013 Society of Plastics Engineers     

Preparation of transparent PVA/TiO2 nanocomposite films with enhanced visible-light photocatalytic activity

Polymer/semiconductor oxide nanocomposite films have been intensively investigated for various applications. In this work, we reported a simple hydrothermal method to fabricate highly transparent poly(vinyl alcohol)/titanium dioxide (PVA/TiO₂) nanocomposite films with enhanced visible-light photocatalytic activity. The as-prepared PVA/TiO₂ nanocomposite films showed high optical transparency in the visible region even at a high TiO₂ content (up to 40 wt.%). The determination of photocatalytic activity by photodegradation of methyl orange (MO) and colorless phenol showed that PVA/TiO₂ nanocomposite films exhibited enhanced visible-light photocatalytic activity and excellent recycle stability. This work provided new insights into fabrication of polymer/TiO₂ nanocomposites as high performance photocatalysts in waste water treatment.     

Studies on electro‐optical properties of polymer matrix/LC/SiO2 nanoparticles composites

Polymer‐dispersed liquid crystal (PDLC) films were prepared by ultraviolet light‐induced polymerization of photopolymerizable monomers in nematic liquid crystal (LC)/monomers/SiO₂ nanoparticles composites, and the effect of SiO₂ nanoparticles on the electro‐optical properties of PDLC films was studied. The observed effect showed that by the adjustment of the SiO₂ nanoparticles content, the refractive index ratio of the LC and polymer could be modulated, and the electro‐optical properties of the polymer matrix/LC/SiO₂ nanoparticles composites could be optimized. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Anomalous behavior of the dielectric and electrical properties of polymeric nanodielectric poly(vinyl alcohol)–titanium dioxide films

The complex dielectric permittivity, alternating‐current electrical conductivity, electric modulus, and impedance spectra of polymeric nanocomposite (PNC) films consisting of a poly(vinyl alcohol) (PVA) matrix dispersed with nanosize particles of titanium dioxide (TiO₂); (i.e., PVA–x wt % TiO₂, where x is 0, 1, 3, or 5) were investigated in the frequency range 20 Hz to 1 MHz at ambient temperature. A detailed analysis of the results showed that the values of the dielectric and electrical parameters of these PNC‐based nanodielectric films varied anomalously with increasing TiO₂ concentration. The temperature‐dependent dielectric characterization of the PVA–3 wt % TiO₂ film revealed that the dielectric polarization at a fixed frequency increased nonlinearly with increasing temperature. The temperature‐dependent electric modulus relaxation time values of the nanodielectric film obeyed Arrhenius behavior. The X‐ray diffraction study confirmed that the crystalline phase of the PVA matrix decreased with increasing TiO₂ concentration; this suggested that the interaction of the TiO₂ nanoparticles caused some destruction of the hydroxyl group dipolar ordering in the hydrogen‐bonded crystalline structure of the pristine PVA matrix. The intensities of the diffraction peaks of the TiO₂ nanofiller were enhanced as its concentration increased in these nanodielectrics; this confirmed the existence of TiO₂ nanoparticles inside the crystalline phases of the PVA matrix. The surface morphology of the films was examined by the study of their scanning electron micrographs. The feasibility of using these flexible polymeric nanodielectric films as electrical insulators and dielectric substrates in low‐power microelectronic devices operated at audio‐ and radio‐frequency electric fields was explored. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44568.     

Enhanced photoresponse and photocatalytic activities of graphene quantum dots sensitized Ag/TiO2 thin film

TiO₂ thin films were fabricated through hydrothermal method. Silver nanoparticles were loaded on TiO₂ thin films via photoreduction technique. Subsequently, the graphene quantum dots (GQDs) were spin‐coated on the Ag/TiO₂ nanocomposites thin films. The crystal structure, surface morphology and UV‐vis absorbance were tested by XRD, SEM and ultraviolet‐visible spectrophotometer. These results indicated that Ag nanoparticles and GQDs are anchored on the TiO₂ nanorods. Absorbance of Ag/TiO₂ and GQDs/Ag/TiO₂ nanocomposite thin films have been extended into the visible region. Visible‐light response of the samples were investigated by electrochemical workstation. The photoresponse of the sample can be enhanced by sensitization of the Ag nanoparticles and GQDs. The enhanced visible‐light response may be due to the surface plasmon resonance of silver nanoparticles and visible absorbance of GQDs. The highest photocatalytic activity has been observed in the 9‐GQDs/Ag/TiO₂ composite thin film. The efficient charge separation and transportation can be achieved by introducing the Ag nanoparticles and GQDs in the TiO₂ thin film.     

Characterization of antireflective coatings on poly(methyl methacrylate) substrate by different process parameters

The high/low refractive index organic/inorganic antireflective (AR) hybrid polymers were formed using the sol–gel process, in which TiO₂/2‐hydroxyethyl methacrylate (2‐HEMA) (high refractive index hybrid polymer) and SiO₂/2‐HEMA (low refractive index hybrid polymer) two‐layer thin films were formed on a hard coating deposited poly(methyl methacrylate) (HC‐PMMA) substrate by both spin coating and dip coating. The relationship between the process parameters and the optical properties, thickness, porosity, surface morphology, and adhesion was determined. The results show that the reflectance of the two‐layer thin films on HC‐PMMA substrate is less than 0.21% (λ = 550 nm), with good adhesion (5B) and a hardness of up to 4H. In addition, the thickness, porosity, and roughness of the films affect refractive index and the antireflection properties of the AR two‐layered thin film. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013