A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

An active‐passive capacitor‐commutated converter for HVDC systems with a three‐phase voltage‐source PWM converter

This paper introduces a new approach to the capacitor‐commutated converters (CCCs) for HVDC systems. A small‐rated three‐phase voltage‐source PWM converter is connected between a series commutation capacitor and thyristor converter through matching transformers. The PWM converter acts as auxiliary commutation‐capacitor for the thyristor converter while the series passive capacitor acts as the main commutation capacitor. The capacitance, which is the sum of the small‐rated active and series passive capacitors, is variable, so that stable commutation is obtained. In CCCs, commutation failure occurs when the AC bus voltage is recovered whereas the proposed combined commutation‐capacitor can achieve successful commutation for both rapidly decreasing and increasing AC bus voltages. The basic principle of the proposed active–passive capacitor‐commutated converter is discussed in detail. Then, constant margin angle control with a constant firing angle of the thyristor converter is proposed using a function generator block. Digital simulation demonstrates the novelty and effectiveness of the proposed active–passive capacitor‐commutated converter. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 151(1): 66–75, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20030     

A new method of damping harmonic resonance at the DC link in a large‐capacity rectifier‐inverter system

This paper proposes a new method of damping harmonic resonance in the DC link of a large‐capacity rectifier‐inverter system, such as in rapid‐transit railways. A voltage‐source PWM converter is connected in series to the DC capacitor of the rectifier through a matching transformer, acting as a damping resistor to the DC capacitor current. No filters are needed to extract harmonic components from the DC capacitor current. This results in a quick response and highly stable damping. The relationship between the control gain of the PWM converter and the required rating is theoretically discussed. We show that the required rating is less than one‐thousandth of that previously proposed. In particular, regenerating the power consumed by the PWM converter is very important because of the large power in practical systems. Normally, an additional PWM inverter is connected to the DC bus of the PWM converter to regenerate the consumed power. The additional inverter regenerates the DC power to the AC source through a transformer. This method, however, makes the damping circuit complex, thus the proposed method for the DC‐link harmonic resonance is less practicable. In this paper, a simple and novel scheme that utilizes the DC‐link voltage of the rectifier as a DC source for the PWM converter is proposed. The excellent practicability of the proposed damping method with the novel regenerating scheme is confirmed using digital computer simulation. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 144(2): 53–62, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10172     

Pulse current regenerative resonant snubber‐assisted two‐switch flyback‐type ZVS PWM DC‐DC converter

In this paper, a two‐switch high‐frequency flyback transformer‐type zero voltage soft‐switching PWM DC‐DC converter using IGBTs is proposed. Effective applications for this power converter can be found in auxiliary power supplies of rolling stock transportation and electric vehicles. This power converter is basically composed of two active power switches and a flyback high‐frequency transformer. In addition to these, two passive lossless snubbers with power regeneration loops for energy recovery, consisting of a three‐winding auxiliary high‐frequency transformer, auxiliary capacitors and diodes are introduced to achieve zero voltage soft switching from light to full load conditions. Furthermore, this power converter has some advantages such as low cost circuit configuration, simple control scheme, and high efficiency. Its operating principle is described and to determine circuit parameters, some practical design considerations are discussed. The effectiveness of the proposed power converter is evaluated and compared with the hard switching PWM DC‐DC converter from an experimental point of view, and the comparative electromagnetic conduction and radiation noise characteristics of both DC‐DC power converter circuits are also depicted. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 152(3): 74–81, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20081     

Compensation for magnetizing inrush currents in transformers using a PWM inverter

When a transformer is connected to a circuit, under certain conditions, magnetizing inrush currents may be about ten times the full load current of the transformer. The currents contain a large amount of harmonic components and cause some relays to trip out. In this paper, the magnetizing inrush currents are compensated using a PWM inverter. The magnetizing inrush currents are detected and the PWM inverter generates compensating currents for the inrush currents. Hysteresis current controllers are used for fast response. The validity of this compensation is investigated by the simulation results. In addition, hardware implementation for the compensator is accomplished to verify the simulation results. Moreover, for the compensator, the relation between the compensating characteristics, the maximum switching frequency, and the coupling reactor is discussed based on the simulation results. Finally, characteristics of two current controllers (hysteresis band current controller and ramp‐comparison controller) are compared and it is shown that the hysteresis band current controller is more suitable for the compensator. The PSCAD/EMTDC electromagnetic transient simulator is used for the simulations. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(2): 53–64, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10023     

Analysis and design of a two‐transformer active‐clamping forward converter with parallel‐connected current doubler rectifiers

A new two‐transformer active‐clamping forward converter with parallel‐connected current doubler rectifiers (CDRs) is proposed in this paper. The presented DC–DC converter is mainly composed of two active‐clamping forward converters with secondary CDRs. Only two switches are required and each one is the auxiliary switch for the other. The circuit complexity and cost are thus reduced. The leakage inductance of the transformer or an additional resonant inductance is employed to achieve zero‐voltage‐switching (ZVS) during the dead times. Two CDRs at the secondary side are connected in parallel to reduce the current stresses of the secondary windings and the ripple current at the output side. Accordingly, the smaller output chokes and capacitors decrease the converter volume and increase the power density. Detailed analysis and design of the presented two‐transformer active‐clamping forward converter are described. Experimental results are recorded for a prototype converter with a DC input voltage of 130??180V, an output voltage of 5 V and an output current of 40 A, operating at a switching frequency of 100 kHz. Copyright © 2010 John Wiley & Sons, Ltd.     

A novel induction generator system using bi‐directional PWM converter for small‐scale power applications

This paper presents a deadbeat current control structure for a bidirectional power flow pulse‐width modulation (PWM) converter connected to a stand‐alone induction generator (IG), which works with variable speed and different types of loads. Sensorless control of the IG, meaning stator voltage vector control without a mechanical shaft sensor, is considered to regulate both the IG line‐to‐line voltage and the DC‐bus voltage of the PWM converter. In the proposed system, a newly designed phase locked loop (PLL) circuit is used to determine the stator voltage vector position of the IG. A 2.2 kW laboratory prototype has been built to confirm the feasibility of the proposed method. The proposed cost‐effective IG system with a deadbeat current‐controlled PWM converter and capacitor bank requires only three sensors. Moreover, the required rating of the PWM converter becomes smaller due to the existence of the capacitor bank. © 2006 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A single‐stage LED streetlight driver with PFC and digital PWM dimming capability

This paper proposes a single‐stage light‐emitting diode (LED) driver that offers power‐factor correction and digital pulse–width modulation (PWM) dimming capability for streetlight applications. The presented LED streetlight driver integrates an alternating current–direct current (AC–DC) converter with coupled inductors and a half‐bridge‐type LLC DC–DC resonant converter into a single‐stage circuit topology. The sub‐circuit of the AC–DC converter with coupled inductors is designed to be operated in discontinuous‐conduction mode for achieving input‐current shaping. Zero‐voltage switching of two active power switches and zero‐current switching of two output‐rectifier diodes in the presented LED driver decrease the switching losses; thus, the circuit efficiency is increased. A prototype driver for powering a 144‐W‐rated LED streetlight module with input utility‐line voltages ranging from 100 to 120 V is implemented and tested. The proposed streetlight driver features cost‐effectiveness, high circuit efficiency, high power factor, low levels of input‐current harmonics, and a digital PWM dimming capability ranging from 20% to 100% output rated LED power, which is fulfilled by a micro‐controller. Satisfying experimental results, including dimming tests, verify the feasibility of the proposed LED streetlight driver. Copyright © 2016 John Wiley & Sons, Ltd.     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Improved control‐to‐output characteristics of a PWM buck‐boost converter

An indirect control variable for improving the control‐to‐output characteristics of a Pulse Width Modulation (PWM) buck‐boost converter is introduced in this letter. The voltage gain and the small‐signal model of the buck‐boost converter are reviewed. The actual voltage command at one input of the PWM comparator is from the proposed indirect control variable and the peak value of the high‐frequency PWM carrier. The resulted voltage gain function appears proportional to this indirect control command. Also the dependence of the DC gain of the control‐to‐output transfer function on the duty cycle is eliminated. Experimental results conform well to the theoretical analysis. Copyright © 2010 John Wiley & Sons, Ltd.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

A control method to realize sinusoidal input and output current waveforms for matrix converters based on PWM

A matrix converter (MC) is a three‐phase AC‐to‐AC direct converter without any energy storage requirement. It is expected to be a next‐generation converter by reason of possibilities of small size and high efficiency. At present, there are some problems preventing it from being used practically. One of the problems is the distortion in the input current. The control methods proposed so far have not realized sufficient reduction of the input current harmonics compared with conventional PWM rectifiers. As a solution to these problems, many approaches have been proposed. In the present paper, an improved PWM method that can achieve both sinusoidal input and output currents simultaneously is considered. In this method, the MC is treated as a controlled voltage source viewed from the load side. On the other hand, it is treated as a controlled current source viewed from the line side. The proposed control method is based on the mathematical expression of the function of the PWM operation of MC. To improve the input current waveform, two line‐to‐line voltages of the three‐phase line are used to control the output current. The output duty ratio of the two line‐to‐line voltages is utilized to improve the input current waveform without affecting the controllability of the output current. In addition, the compensation of the variations in the line voltage and the output current are introduced. In this way, the proposed method can realize the sinusoidal input and output currents. The effectiveness of the proposed control method is confirmed by some experimental results employing a laboratory prototype. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(1): 66–76, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20242     

Analysis and design of a two‐transformer active‐clamping ZVS isolated inverse‐SEPIC converter

This paper presents a two‐transformer active‐clamping zero‐voltage‐switching (ZVS) isolated inverse‐SEPIC converter, which is mainly composed of two active‐clamping ZVS isolated inverse‐SEPIC converters. The proposed converter allows a low‐profile design for liquid crystal display TVs and servers. The presented two‐transformer active‐clamping ZVS isolated inverse‐SEPIC converter can equally share the total load current between two secondaries. Therefore, the output inductor copper loss and the output diode conduction loss can be decreased. Detailed analysis and design of this new two‐transformer active‐clamping ZVS isolated inverse‐SEPIC converter are described. Experimental results are recorded for a prototype converter with an AC input voltage ranging from 85 to 135 V, an output voltage of 12 V and a rated output current of 13.5A, operating at a switching frequency of 65 kHz. Copyright © 2012 John Wiley & Sons, Ltd.     

Operation analysis of quasi‐resonant,high‐frequency transformer link dc–ac converters applied to phase‐shift PWM control on the secondary side

In recent years, the soft‐switching techniques have attracted attention for their peculiar advantages such as low switching loss, high power density, EMI/RFI noise reduction, and so on. The authors have previously reported on a quasi‐resonant dc–dc converter using new phase‐shift PWM control scheme. By using the proposed control scheme, circulating current is eliminated and ZVS (Zero Voltage Switching) is achieved with small commutating current. As a result, the conduction losses caused by their currents are substantially reduced. In this paper, the authors apply a proposed control scheme to a quasi‐resonant high‐frequency transformer link dc–ac converter. As a result, all switching devises in this dc–ac converter can achieve soft switching with small commutating current irrespective of inverter mode and rectifier mode. Its operating principle and unique features are described as compared with the symmetrical control scheme of dc–ac converter. Operating performance of this dc–ac converter in the steady state is illustrated by means of simulation results. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 88–98, 2000     

A step‐up PWM DC–DC converter for renewable energy applications

A step‐up pulse width modulation (PWM) direct current (DC)–DC converter is presented in this paper, which has its origin in quasi Z‐source inverter. Analysis of this converter in steady state is presented, and relevant expressions are derived for the proposed converter operating in continuous conduction mode. The power loss expressions for each component of the converter are derived, and thereby, obtained expressions for overall converter efficiency are presented. Further, a dynamic model is derived to design an appropriate controller for this converter. The simulation and experimental results are presented to support the theoretical analysis. The advantages such as continuous input current, high step‐up gain at lower duty ratio, and common ground for source, load, and switch makes the converter suitable for renewable energy applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Analysis,design and implementation of a high‐voltage gain DC‐DC converter

An interleaved DC‐DC converter with soft switching technique is presented. There are two converter modules in the adopted circuit to share the load power. Since the interleaved pulse‐width modulation (PWM) is adopted to control two circuit modules, the ripple currents at input and output sides are naturally reduced. Therefore the input and output capacitances can be reduced. In each circuit module, a conventional boost converter and a voltage doubler configuration with a coupled inductor are connected in series at the output side to achieve high step‐up voltage conversion ratio. Active snubber connected in parallel with boost inductor is adopted to limit voltage stress on active switch and to release the energy stored in the leakage and magnetizing inductances. Since asymmetrical PWM is used to control active switches, the leakage inductance and output capacitance of active switches are resonant in the transition interval. Thus, both active switches can be turned on at zero voltage switching. The resonant inductance and output capacitances at the secondary side of transformer are resonant to achieve zero current switching turn‐off for rectifier diodes. Therefore, the reverse recovery losses of fast recovery diodes are reduced. Finally, experiments based on a laboratory prototype rated at 400 W are presented to verify the effectiveness of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

Series resonant high‐voltage DC–DC converter with reduced component count

This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A novel prototype of auxiliary edge resonant bridge leg link snubber‐assisted soft‐switching sine‐wave PWM inverter

This paper proposes a new circuit topology of the three‐phase soft‐switching PWM inverter and PFC converter using IGBT power modules, which has the improved active auxiliary switch and edge resonant bridge leg‐commutation‐link soft‐switching snubber circuit with pulse current regenerative feedback loop as compared with the typical auxiliary resonant pole snubber discussed previously. This three‐phase soft‐switching PWM double converter is more suitable and acceptable for a large‐capacity uninterruptible power supply, PFC converter, utility‐interactive bidirectional converter, and so forth. In this paper, the soft‐switching operation and optimum circuit design of the novel type active auxiliary edge resonant bridge leg commutation link snubber treated here are described for high‐power applications. Both the main active power switches and the auxiliary active power switches achieve soft switching under the principles of ZVS or ZCS in this three‐phase inverter switching. This three‐phase soft‐switching commutation scheme can effectively minimize the switching surge‐related electromagnetic noise and the switching power losses of the power semiconductor devices; IGBTs and modules used here. This three‐phase inverter and rectifier coupled double converter system does not need any sensing circuit and its peripheral logic control circuits to detect the voltage or the current and does not require any unwanted chemical electrolytic capacitor to make the neutral point of the DC power supply voltage source. The performances of this power conditioner are proved on the basis of the experimental and simulation results. Because the power semiconductor switches (IGBT module packages) have a trade‐off relation in the switching fall time and tail current interval characteristics as well as the conductive saturation voltage characteristics, this three‐phase soft‐switching PWM double converter can improve actual efficiency in the output power ranges with a trench gate controlled MOS power semiconductor device which is much improved regarding low saturation voltage. The effectiveness of this is verified from a practical point of view. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 64–76, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20207     

Isolated high voltage‐boosting converter derived from forward converter

A novel isolated high voltage‐boosting converter, derived from the traditional forward converter, is presented in this paper. As compared with the traditional forward converter, the demagnetizing winding of the transformer in the proposed converter is used not only to demagnetize but also to improve the voltage conversion ratio. Therefore, the duty cycle is not limited, and the utilization of the transformer, also called coupled inductor, can be increased also. Furthermore, the proposed converter maintains the advantage of possessing a non‐pulsating output current, leading to a small output voltage ripple. Moreover, by applying one additional voltage‐boosting winding to the transformer, the voltage conversion ratio can be significantly improved. In addition, an active clamp circuit is employed in the proposed converter to reduce the voltage stress of the main switch, caused by the leakage inductance in the transformer, and the switches can achieve zero‐voltage switching. Finally, the analysis of operating principles, choice of the turns, turns ratio, core size, and each wire size of the coupled inductor are described in detail, and the experimental results with a prototype with 12‐V input voltage, 100‐V output voltage, and 100‐W output power are provided to verify the feasibility and effectiveness of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.