Synthesis, characterization and catalytic activity for NO–CO reaction of Pd–(La, Sr)2MnO4 system

La_xSr_2−xMnO₄ (0 ≤ x ≤ 0.8) oxides were synthesized and single-phase K₂NiF₄-type oxides were obtained in the range of 0.1 ≤ x < 0.5. The catalytic activity of La_xSr_2−xMnO₄ for NO–CO reaction increased with increasing x in the range of solubility limit of La. La_0.5Sr_1.5MnO₄ showed the highest activity among La_xSr_2−xMnO₄ prepared in this study, but its activity was inferior to perovskite-type La_0.5Sr_0.5MnO₃. Among the Pd-loaded catalysts, however, Pd/La_0.8Sr_1.2MnO₄ showed the higher activity and the selectivity to N₂ than Pd/La_0.5Sr_0.5MnO₃ and Pd/γ-Al₂O₃. The excellent catalytic performance of Pd/La_0.2Sr_1.2MnO₄ could be ascribable to the formation of SrPd₃O₄ which was detected by XRD in the catalyst but not in the other two catalysts.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Study of Ag/La0.6Ce0.4CoO3 catalysts for direct decomposition and reduction of nitrogen oxides with propene in the presence of oxygen

Perovskite-type oxide La_0.6Ce_0.4CoO₃ and its doped Ag catalysts were prepared and their catalytic performances were evaluated for the direct decomposition of NO and the selective reduction of NO with propene in the presence of oxygen. A noticeable enhancement in activity was achieved by doping Ag and the optimum Ag loading was 1%. The effects of H₂O, SO₂, CO₂ and O₂ on the performances of Ag/La_0.6Ce_0.4CoO₃ catalysts for NO decomposition were also investigated. The resistance against H₂O and SO₂ appears satisfactory. The inhibition by CO₂ is strong, although it is reversible. Oxygen did not inhibit the NO decomposition reaction but significantly promoted it. Compared with other perovskite-type oxides reported previously, higher conversions were obtained over the present catalysts for the NO reduction by propene. We speculate that the decomposition of NO is the predominant process even in the presence of propene. The catalysts were characterized by N₂-adsorption, XRD, XPS and NO-TPD and some explanations were put forward.     

Catalytic combustion of CH4 and CO on La1−xMxMnO3 perovskites

The activities of perovskites depend on compositions and preparation methods. Various perovskites, La_1−xM_xMnO₃ (M=Ag, Sr, Ce, La), have been prepared by two different methods (co-precipitation and spray decomposition). The new preparation method, spray decomposition, produced perovskites of a high surface area of over 10 m²/g. The catalytic activities for CH₄ and CO oxidation have been studied on a series of catalysts, La_1−xM_xMnO₃. The perovskite-type oxide, La_0.7Ag_0.3MnO₃, shows the highest catalytic activity: the complete conversion of CO and CH₄ at 370 and 825 K, respectively.     

An investigation of NO/CO reaction over perovskite-type oxide La0.8Ce0.2B0.4Mn0.6O3 (B = Cu or Ag) catalysts synthesized by reverse microemulsion

The perovskite-type oxides La_0.8Ce_0.2Cu_0.4Mn_0.6O₃ and La_0.8Ce_0.2Ag_0.4Mn_0.6O₃ prepared by reverse microemulsion and sol–gel methods (denoted as R and S, respectively), have been investigated on their catalytic performance for the (NO + CO) reaction, and characterized by means of temperature-programmed desorption (TPD), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). XRD measurements proved the presence of the perovskite phase with a considerable amount of CeO₂ phase and the formation of CeO₂ phase was restrained with the reverse microemulsion method. TEM investigations revealed that the La_0.8Ce_0.2Cu_0.4Mn_0.6O₃-R nanoparticles were uniform spheres in shape with diameters ranging from 40 to 50 nm, whereas an aggregation of particles was found for the La_0.8Ce_0.2Cu_0.4Mn_0.6O₃-S catalyst. The activity of NO reduction with CO decreased in the order of La_0.8Ce_0.2Cu_0.4Mn_0.6O₃-R > La_0.8Ce_0.2Cu_0.4Mn_0.6O₃-S > La_0.8Ce_0.2Ag_0.4Mn_0.6O₃-R > La_0.8Ce_0.2Ag_0.4Mn_0.6O₃-S. In NO-TPD experiments, the principal desorbed species detected in the effluent was NO with a trace amount of O₂ and N₂O, suggesting that the non-dissociated adsorption of NO on the surface of the perovskite-type oxides was dominant. The XPS results revealed that Ce⁴⁺ and Cu⁺ was the predominant oxidation state for Ce and Cu components in La_0.8Ce_0.2Cu_0.4Mn_0.6O₃ and La_0.8Ce_0.2Ag_0.4Mn_0.6O₃ catalysts. The existence of Cu⁺ ions and its redox reaction (Cu⁺ ↔ Cu²⁺) would benefit the NO adsorption and reduction by CO.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

Nanosized perovskite-type oxides La1−xSrxMO3−δ (M = Co, Mn; x = 0, 0.4) for the catalytic removal of ethylacetate

Nanometer perovskite-type oxides La_1−xSr_xMO_3−δ (M = Co, Mn; x = 0, 0.4) have been prepared using the citric acid complexing-hydrothermal-coupled method and characterized by means of techniques, such as X-ray diffraction (XRD), BET, high-resolution scanning electron microscopy (HRSEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and temperature-programmed reduction (TPR). The catalytic performance of these nanoperovskites in the combustion of ethylacetate (EA) has also been evaluated. The XRD results indicate that all the samples possessed single-phase rhombohedral crystal structures. The surface areas of these nanomaterials ranged from 20 to 33 m² g⁻¹, the achievement of such high surface areas are due to the uniform morphology with the typical particle size of 40–80 nm (as can be clearly seen in their HRSEM images) that were derived with the citric acid complexing-hydrothermally coupled strategy. The XPS results demonstrate the presence of Mn⁴⁺ and Mn³⁺ in La_1−xSr_xMnO_3−δ and Co³⁺ and Co²⁺ in La_1−xSr_xCoO_3−δ, Sr substitution induced the rises in Mn⁴⁺ and Co³⁺ concentrations; adsorbed oxygen species (O⁻, O₂⁻, or O₂²⁻) were detected on the catalyst surfaces. The O₂-TPD profiles indicate that Sr doping increased desorption of the adsorbed oxygen and lattice oxygen species at low temperatures. The H₂-TPR results reveal that the nanoperovskite catalysts could be reduced at much lower temperatures (<240 °C) after Sr doping. It is observed that under the conditions of EA concentration = 1000 ppm, EA/oxygen molar ratio = 1/400, and space velocity = 20,000 h⁻¹, the catalytic activity (as reflected by the temperature (T_100%) for EA complete conversion) increased in the order of LaCoO_2.91 (T_100% = 230 °C) ≈ LaMnO_3.12 (T_100% = 235 °C) < La_0.6Sr_0.4MnO_3.02 (T_100% = 190 °C) < La_0.6Sr_0.4CoO_2.78 (T_100% = 175 °C); furthermore, there were no formation of partially oxidized by-products over these catalysts. Based on the above results, we conclude that the excellent catalytic performance is associated with the high surface areas, good redox properties (derived from higher Mn⁴⁺/Mn³⁺ and Co³⁺/Co²⁺ ratios), and rich lattice defects of the nanostructured La_1−xSr_xMO_3−δ materials.     

柠檬醛在La2O3/γ-Al2O3催化剂上的等温吸附

对柠檬醛-乙酸乙酯溶液中柠檬醛在La₂O₃/γ-Al₂O₃催化剂上等温吸附行为进行了研究。结果表明,30 ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的吸附动力学符合准二阶吸附动力学模型,吸附动力学方程为：1/q_t=2.350/t+0.063 3(R²=0.998 5)。（30~65） ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的等温吸附符合Langmuir方程,温度升高使柠檬醛的饱和吸附量增加,吸附热为32.19 kJ·mol^-1。     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Synthesis and catalytic properties of Ce0.6Zr0.4O2 solid solutions in the oxidation of soluble organic fraction from diesel engines

Ce_0.6Zr_0.4O₂ solid solutions were synthesized by co-precipitation, sol–gel like method, solution combustion and surfactant-assistant approaches, respectively. The catalytic properties of bulk and γ-Al₂O₃ supported Ce_0.6Zr_0.4O₂ solid solutions were studied for the oxidation of soluble organic fractions (SOF) from diesel engines by TG-DTA method. The physicochemical properties were characterized by XRD, BET surface area and pore distribution, SEM, TEM, and particle size distribution techniques. XRD and TEM results show that a Ce_0.6Zr_0.4O₂ solid solution was formed for samples as-prepared and heat-treated at 900 °C for 2 h in air. The co-precipitation derived Ce_0.6Zr_0.4O₂ has as high BET surface area as 153.71 m²/g by controlling preparation conditions. Notable is that the surface area and particle size for fresh Ce_0.6Zr_0.4O₂ ignited at 350 °C decreased little after a thermal treatment in air at 900 °C for 2 h. Furthermore, its bulk density is lowest. The commercial engine oil (SJ5W/40) for FAW-VOLKSWAGEN, which was used by Bora 1.9 TDI diesel cars in China market was substituted for SOF. The catalytic activity was evaluated by normalized peak areas and extrapolated onset temperatures of DTA curves. A computer program was developed by direct non-linear regression model for simulation of TG/DTG curves to determine the thermal processes and kinetic parameters. It is found that lube evaporation/decomposition and thermal decomposition (pyrolysis) were observed under a nitrogen atmosphere. Lube evaporation fractions were inhibited by Ce_0.6Zr_0.4O₂ and γ-Al₂O₃. While under an air atmosphere, namely, in the process of lube oxidation (combustion), evaporation/decomposition, low-temperature oxidation and high-temperature oxidation were distinguished. Ce_0.6Zr_0.4O₂ solid solutions are active catalysts for lube oxidation, in which the sample prepared by solution combustion has the highest activity, mainly due to the maintenance of the surface area and particle size upon sintering and its lowest bulk density. However, γ-Al₂O₃ is more like a support. There exists synergism between Ce_0.6Zr_0.4O₂ and γ-Al₂O₃: γ-Al₂O₃ adsorbs lube retaining it within its pore structure, whereas, Ce_0.6Zr_0.4O₂ solid solutions initiate oxidation reactions when light-off temperatures reach. The application of CeO₂-ZrO₂ solid solution prepared by solution combustion at lower temperature would be promising in diesel oxidation catalysts.     

Reduction of CeO2 in composites with transition metal complex oxides under hydrogen containing atmosphere and its correlation with catalytic activity

Reduction behavior of pure and doped CeO₂, the multi-phase La_0.6Sr_0.4CoO₃?xCeO₂, La_0.8Sr_0.2MnO₃ ?xCeO₂, and La_0.95Ni_0.6Fe_0.4O₃?xCeO₂ composites, was studied under hydrogen containing atmosphere to address issues related to the improvement of electrochemical and catalytic performance of electrodes in fuel cells. The enhanced reduction of cerium oxide was observed initially at 800°C in all composites in spite of the presence of highly reducible transition metal cations that could lead to the increase in surface concentration of oxygen vacancies and generation of the electron enriched surface. Due to continuous reduction of cerium oxide in La_0.6Sr_0.4CoO₃?xCeO₂ and La_0.8Sr_0.2MnO₃?xCeO₂ (up to 10 h) composites the redox activity of the Ce⁴⁺/Ce³⁺ pair could be suppressed and additional measures are required for reversible spontaneous regeneration of Ce⁴⁺. After 3 h exposure to H₂-Ar at 800°C the reduction of cerium oxides and perovskite phases in La_0.95Ni_0.6Fe_0.4O₃?xCeO₂ composites was diminished. The extent of cerium oxide involvement in the reduction process varies with time, and depends on its initial deviation from oxygen stoichiometry (that results in the larger lattice parameter and the longer pathway for O^2- transport through the fluorite lattice), chemical origin of transition metal cations in the perovskite, and phase diversity in multi-phase composites.     

Oxidative coupling of methane in a mixed-conducting perovskite membrane reactor

Ionic-electronic mixed-conducting perovskite-type oxide La_0.6Sr_0.4Co_0.8Fe_0.2O₃ was applied as a dense membrane for oxygen supply in a reactor for methane coupling. The oxygen permeation properties were studied in the p_O2-range of 10⁻³−1 bar at 1073–1273 K, using helium as a sweeping gas at the permeate side of the membrane. The oxygen semi-permeability has a value close to 1 mmol m⁻² s⁻¹ at 1173 K with a corresponding activation energy of 130–140 kJ/mol. The oxygen flux is limited by a surface process at the permeate side of the membrane. It was found that the oxygen flux is only slightly enhanced if methane is admixed with helium. Methane is converted to ethane and ethene with selectivities up to 70%, albeit that conversions are low, typically 1–3% at 1073–1173 K. When oxygen was admixed with methane rather than supplied through the membrane, selectivities obtained were found to be in the range 30–35%. Segregation of strontium was found at both sides of the membrane, being seriously affected by the presence of an oxygen pressure gradient across it. The importance of a surface limited oxygen flux for application of perovskite membranes for methane coupling is emphasized.     

Oxygen transport in ferrite-based ceramic membranes: Effects of alumina sintering aid

Moderate additions of Al₂O₃ to strontium ferrite-based mixed conductors, such as SrFe_0.7Al_0.3O_3−δ and La_0.2Sr_0.8Fe_0.8Ga_0.2O_3−δ with the composition close to the solid solution formation limits, make it possible to improve ceramics sinterability, to increase oxygen permeability and to decrease thermal expansion. These effects are associated with the segregation of alumina-rich phases, primarily SrAl₂O₄, and the formation of A-site cation-deficient perovskite. The improved properties of the SrFe_0.7Al_0.3O₃-based material were used to fabricate high-quality tubular membranes for methane conversion reactors. Similar enhancement in sinterability is also observed for another promising parent material of mixed-conducting membranes, La_0.5Sr_0.5FeO_3−δ. However, extensive dissolution of Al³⁺ cations in the iron sublattice, creation of A-site vacancies and changing the La:Sr concentration ratio all lead to decreasing ionic transport in La_0.5Sr_0.5FeO_3−δ. As a result, additions of either Al₂O₃ or SrAl₂O₄ have a deteriorating influence on the oxygen permeation fluxes through La_0.5Sr_0.5FeO₃-based ceramics.     

Kinetic studies of CH4 oxidation over Pt–NiO/δ-Al2O3 in a fluidised bed reactor

The oxidation of CH₄ over Pt–NiO/δ-Al₂O₃ has been studied in a fluidised bed reactor as part of a major project on an autothermal (combined oxidation–steam reforming) system for CH₄ conversion. The kinetic data were collected between 773 and 893 K and 101 kPa total pressure using CH₄ and O₂ compositions of 10–35% and 8–30%, respectively. Rate–temperature data were also obtained over alumina-supported monometallic catalysts, Pt and NiO. The bimetallic Pt–NiO system has a lower activation energy (80.8 kJ mol⁻¹) than either Pt (86.45 kJ mol⁻¹) and NiO (103.73 kJ mol⁻¹). The superior performance of the bimetallic catalyst was attributed to chemical synergy. The reaction rate over the Pt–NiO catalyst increased monotonically with CH₄ partial pressure but was inhibited by O₂. At low partial pressures (<30 kPa), H₂O has a detrimental effect on CH₄ conversion, whilst above 30 kPa, the rate increased dramatically with water content.     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

Deactivation studies over NiO/γ-Al2O3 catalysts for partial oxidation of methane to syngas

Two types of NiO/γ-Al₂O₃ catalysts prepared by the impregnation and the sol–gel method were used for the partial oxidation of methane to syngas at 850°C (GHSV1.8×10⁵ lkg⁻¹ h⁻¹). The effects of the carbon deposition, the loss and sintering of nickel and the phase transformation of γ-Al₂O₃ support on the catalytic performance during 80 h POM reaction were investigated with a series of characterization such as XRD, BET, AAS, TG, and XPS. The results indicated that the carbon deposition and the loss and sintering of nickel could not cause the serious decrease of catalytic performance over NiO/γ-Al₂O₃ catalyst during the short-time reaction. However, the slow process of the support γ-Al₂O₃ phase transforming into -Al₂O₃ could slowly decrease the performance of NiO/γ-Al₂O₃ catalysts. Aimed at the reasons of the deactivation, an improved catalyst was obtained by the complexing agent-assisted sol–gel method.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

Influence of molar ratio of citric acid to metal ions on preparation of La0.67Sr0.33MnO3 materials via polymerizable complex process

Polycrystalline La_0.67Sr_0.33MnO₃ (LSMO) nanometric sized powders and thin films are obtained from the resins synthesized by the polymerization of citric acid and ethylene glycol. Molar ratios of citric acid to metal ions were varied, and the resulting effects on the powder's properties were studied using TGA/DTA, FTIR, SEM and X-ray diffraction (XRD). The results indicated that with the molar ratio of citric acid/metal ions at 4, the resin contained a lower fraction of monodentate ligand and a higher portion of CCO structure obtained from ethylene glycol, which made it possible to synthesize the perovskite phase at temperature as low as 500 °C. The powder calcined at 550 °C exhibited a pure phase of perovskite, had a particle size of about 20–50 nm and a specific surface area of 25.24 m²/g. Thin films were prepared by using the as-prepared sols for spin coating on (1 0 0) Si substrate to investigate the properties of the films. As a result of the molar ratio of citric acid/metal cations at 3–4, the transformation of rhombohedral structure to cubic structure was observed.     

Application of Ce0.33Zr0.63Pr0.04O2-supported noble metal catalysts in the catalytic wet air oxidation of 2-chlorophenol: Influence of the reaction conditions

In this work, different procedures, namely carbonate coprecipitation and modified solid–solid diffusion, were used to prepare hexaaluminate samples, unsupported or supported onto θ-Al₂O₃. These samples were used as catalyst for the methane total oxidation as synthesized or after impregnation of 1 wt% Pd. It was observed that the modified solid–solid diffusion procedure is an efficient method to obtain the hexaaluminate structure. At a theoretical ratio x of hexaaluminate onto Al₂O₃ less than 0.6 (xLa_0.2Sr_0.3Ba_0.5MnAl₁₁O₁₉ + (1−x)·Al₂O₃, with x = 0.25, 0.60), samples with high specific surface area and θ-Al₂O₃ structure are then obtained. Large differences in catalytic activity can be observed among the series of sample synthesized. All the pure oxide samples (i.e. without palladium) present low catalytic activity for methane total oxidation compared to a reference Pd/Al₂O₃ catalyst. The highest activity was obtained for the samples presenting a θ-Al₂O₃ structure (with x = 0.60) and a high surface area. Impregnation of 1 wt% palladium resulted in an increase in catalytic activity, for all the solids synthesized in this work. Even if the lowest light-off temperature was obtained on the reference sample, similar methane conversions at high temperature (700 °C) were obtained on the stabilized θ-Al₂O₃ solids (x = 0.25, 0.60). Moreover, the reference sample is found to strongly deactivate with reaction time at the temperature of test (700 °C), due to a progressive reduction of the PdO_x active phase into the less active Pd° phase, whereas excellent stabilities in reaction were obtained on the pure and palladium-doped hexaaluminate and supported θ-Al₂O₃ samples. This clearly showed the beneficial effect of the support for the stabilization of the PdO_x active phase at high reaction temperature. These properties are discussed in term of oxygen transfer from the support to the palladium particle. Oxygen transfer is directly related to the Mn³⁺/Mn²⁺ redox properties (in the case of the hexaaluminate and stabilized θ-Al₂O₃ samples), that allows a fast reoxidation of the metal palladium sites since palladium sites reoxidation cannot occur directly by gaseous dioxygen adsorption and dissociation on the surface.