Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

Optical second-harmonic investigations of the isothermal desorption of SiO from the Si(100) and Si(111) surfaces

The isothermal desorption of SiO from the Si(100) and Si(111) surfaces was investigated by means of optical second-harmonic generation (SHG). Due to the high adsorbate sensitivity of this method, desorption rates could be measured over a wide range from 10⁻¹ to 10⁻⁶ ML s⁻¹. From their temperature dependence between 780 and 1000 K, activation energies of E_A=3.4±0.2 eV and E_A=4.0±0.3 eV and pre-exponential factors of ν₀=10^16±1 s⁻¹ and ν₀=10^20±1 s⁻¹ for SiO desorption were obtained for Si(100) and Si(111), respectively. In the case of the Si(100) surface, a pronounced decrease of the first-order rate constants was observed upon increasing the initial coverage from 0.02 to 0.6 ML. The results are interpreted in terms of coverage-dependent oxygen-binding configurations, which influence the stability of the oxide layer.     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

Methane mobility in carbon nanotubes

Quasi-elastic neutron scattering has been used to characterize the diffusivity of CH₄ molecules condensed in single-wall carbon nanotubes. It is shown that the two sites of adsorption, previously observed by adsorption volumetry and calorimetry measurements, correspond to a solid-like phase for the more strongly bound site at T<120 K and to a liquid-like component for the more weakly bound site at 70<T<120 K. The diffusion coefficients of the mobile molecules range between 3×10⁻⁷ to 15×10⁻⁷ cm² s⁻¹. The fraction of this viscous liquid diminishes as the temperature is decreased; the adsorbate is fully solidified at 50 K and below.     

Coulometric titrations of electrolytes in water by a solid state ionic device using Nafion and Tosflex membranes

A solid state ionic device to titrate electrolytes in water was produced, and the performance of the device was examined. The device named the coulometric titration apparatus is a three-component electrochemical cell like an electrodialyzer. The central component, the analyzing room, is a container of the sample solution. The sample solution, 10⁻¹ M H₂SO₄, NaOH, Na₂SO₄, or 10⁻⁷–10⁻² M Na₂SO₄, is separated from the cathode and the anode room solutions, 10⁻² M H₂SO₄, NaOH, or Na₂SO₄, by Nafion-117 and Tosflex IE-SF34 membranes working as the anion and the cation blocking electrodes, respectively. The quantity of electricity to extract whole electrolytes in the sample solution is evaluated from the peak area of the titration curve. The sample concentration is successfully determined by the calibration curve method, with the quantity of electricity and the sample volume (6 ml) in the range from 10⁻¹ to 10⁻⁵ M.     

Electronic conduction properties of Au/C60/p-Si and C60/Au/p-Si sandwich structures: I–V and transducer characteristics

Gold-fullerite [C₆₀]-silicon (p-type) sandwich structures have been fabricated in order to investigate intrinsic cross-sectional and planar electronic conductive properties, in particular the C₆₀/p-Si p–n heterojunction. The turn-on voltage of this p–n heterojunction lies in the range 0.25–0.27 V. The I–V characteristics of the Au/C₆₀/p-Si structure are mostly defined by the bulk specific resistance of the fullerite crystal film itself (6×10⁷ Ω cm). I–V curves in the C₆₀/Au/p-Si structure are shown to be ohmic. Au/C₆₀/p-Si sandwiches irradiated with swift (300 MeV) heavy ions, (⁸⁴Kr¹⁴⁺) to a total fluence 10¹⁰ ion/cm² yield structures which are sensitive to ambient air pressure, specifically in the case of a transverse contact configuration, and if one of the contacts is located on the irradiated part of the fullerite film. The sandwich-structure sensitivity to pressure is 5×10⁻⁶ Pa⁻¹. This exceeds the sensitivity of conventional silicon pressure transducers by almost three orders of magnitude.     

The study of hydronium NASICON conductivity with deuterium

The ionic conductivity of the bulk phase of bonded hydronium NASICON (Hyceram^TM) was measured at equilibrium with an H₂O/N₂ and then a D₂O/N₂ atmosphere, each at 100% relative humidity and 75% relative humidity over the temperature range 25°C to 50°C. At 100% relative humidity and 25°C, the protonic system had a bulk conductivity of 5.0×10⁻⁴ S/cm and an activation energy of 17.3kJ/mole; the same sample, when deuterated, had a bulk conductivity of 2.2×10⁻⁴ S/cm and an activation energy of 19.3kJ/mole. At 75% relative humidity and 25°C, the conductivity of the protonated system decreased to 1.4×10⁻⁴S/cm with an activation energy of 24.1 kJ/mole. The deuterated sample at 75% relative humidity had a bulk conductivity of 5.4×10⁻⁵ S/cm with an activation energy of 26.0 kJ/mole. The isotope effect suggested a proton hopping (Grotthus) mechanism as the means by which the protons pass through the lattice.     

Study of effects of Mn in CdS nanocrystals

Mn²⁺-doped CdS nanocrystals have been synthesized by adopting an aqueous solution precipitation method. These nanocrystals have been studied using X-ray diffraction (XRD), X-ray fluorescence (XRF), optical absorbance, photoluminescence (PL), DC electrical conductivity measurements and positron annihilation lifetime spectroscopy (PALS). The system has been found to be in the hexagonal phase. PL spectra have been studied on most prominent exciton peaks within the wavelength range (586–731 nm). The emission intensity is found to increase on increasing Mn²⁺ ion concentration (0–5%). Electrical conductivity lies within 0.819×10⁻⁶ to 1.69×10⁻⁶ Ω⁻¹ m⁻¹ and the system shows power law dependence for n=3–3.77. The Cd vacancies concentration has been found to decrease on increasing Mn%.     

Z-scan determination of the third-order optical nonlinearity of a triphenylmethane dye using 633 nm He–Ne laser

The third-order nonlinear optical response of a triphenylmethane dye (Acid blue 7) was studied using the Z-scan technique with a continuous-wave He–Ne laser radiation at 633 nm. The magnitude and sign of the third-order nonlinear refractive index n₂ of aqueous solution of Acid blue 7 dye were determined; the negative sign indicates a self-defocusing optical nonlinearity in the sample studied. The negative nonlinear refractive index n₂ and nonlinear absorption coefficient β were estimated to be −1.88 × 10⁻⁷ cm²/W and −3.08 × 10⁻³ cm/W, respectively, corresponding to Re(χ⁽³⁾) = −8.35 × 10⁻⁶ esu, and Im(χ⁽³⁾) = −6.88 × 10⁻⁷ esu. The experimental results show that Acid blue 7 dye have potential applications in nonlinear optics.     

Reaction kinetics of the Pt, O2(g)|c-ZrO2 system: precursor-mediated adsorption

A micro kinetic model of the Pt, O₂(g)|c-zirconia electrode/electrolyte system was developed in state space form (model M3). The oxygen adsorption/desorption process was modeled as a precursor-mediated surface reaction. The surface diffusion of atomic oxygen and the electrochemical reduction of atomic oxygen near the three-phase boundary (tpb) were considered. It was shown that the simulated charge-transfer behavior of M3 is significantly different from models with ordinary Langmuir kinetics (model M2). The electrochemical rate constant was estimated from selected experimental data as k₁₀=(6.05±0.25)·10⁶ m³/(mol·s). From experimental results it was concluded that only one adsorbed oxygen species is relevant for the dynamic behavior. In porous Pt electrodes binary gas phase diffusion of oxygen in O₂/N₂ gas mixtures becomes relevant at oxygen partial pressures below 10⁻³ atm. The general procedure for state and parameter estimation can be well adopted for the investigation of further reaction mechanisms.     

Isothermal desorption of hydrogen from polycrystalline diamond films

The kinetics of isothermal H₂ desorption from polycrystalline diamond are studied in real time. The surface H coverage (θ_H) is measured by mass analyzing the recoiled H₊ ion signal during the desorption. We find that the H₂ desorption is 1st order in θ_H with an activation energy of 69 ± 6 kcal/mol and a prefactor of 10^{10.5 ± 0.9} s⁻¹. We suggest that formation of a C---C π-bond on the clean surface plays a key role in H₂ desorption from diamond, a view consistent with previous theoretical calculations of H₂ desorption from diamond.     

Picosecond nonlinear optical response of Ba0.5Sr0.5TiO3 thin films fabricated by pulsed laser deposition

Well-crystallized Ba_0.5Sr_0.5TiO₃ thin films with good surface morphology were prepared on MgO(1 0 0) substrates by pulsed laser deposition technique at a deposition temperature of 800 °C under the oxygen pressure of 2 × 10⁻³ Pa. X-ray diffraction and atomic force microscopy were used to characterize the films. The full width at half maximum of the (0 0 2) Ba_0.5Sr_0.5TiO₃ rocking curve and the root-mean-square surface roughness within the 5 μm × 5 μm area were 0.542° and 0.555 nm, respectively. The nonlinear optical properties of the films were determined by a single beam Z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that Ba_0.5Sr_0.5TiO₃ thin films exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 5.04 × 10⁻⁶ cm²/kW and β = 3.59 × 10⁻⁶ (m/W), respectively.     

Impedance studies on polyacrylonitrile–CuX2–DMSO (X=Cl, Br, CF3SO3) solid polymer electrolyte

A series of polyacrylonitrile–dimethylsulfoxide–CuX₂ (X=CF₃SO₃⁻, Cl⁻, Br⁻), films (foils) were prepared by means of the solution cast technique. The thickness of the foils was between 0.04 and 0.09 cm and they contained 70–80 wt.% of the solvent. Conductivities of the solid electrolytes were obtained from impedance measurements. The conductivity increases with the increase of the salt content up to 8 wt.%; at higher concentrations (>8 wt.%) the conductivity is more or less stable, and reaches, in the case of Cu(CF₃SO₃)₂ and CuCl₂, the level of ca. 10⁻³ Ω⁻¹ cm⁻¹ at room temperature. The foils based on the CuBr₂ show even higher conductivity, close to 10⁻² Ω⁻¹ cm⁻¹ at room temperature, a value comparable to that characteristic for liquid solutions. The temperature variation of the conductivity for all the systems studied is of the Arrhenius type. The activation energy, determined from linear plots lnσ=f(T⁻¹), is of the order ca. 14 kJ mol⁻¹ for the PAN/CuBr₂/DMSO and of ca. 21 kJ mol⁻¹ for the PAN/CuCl₂/DMSO and the PAN/Cu(CF₃SO₃)₂/DMSO systems.     

Domain wall pinning in polycrystalline perovskite La0.7Sr0.3MnO3

Reversible and irreversible domain wall (DW) motions have been investigated in La_0.7Sr_0.3MnO₃ ceramic samples using frequency-response complex permeability with various amplitudes of AC field. We also examine the effects of temperature in the range from 293 to 368 K and transverse DC magnetic field with a maximum of 4.40×10⁵ A/m on the real part of permeability (μ′). Two relaxations corresponding to reversible wall motions and domain rotations occur in low and high frequency regions, respectively. The irreversible DW displacements can be activated as the amplitude larger than the pinning field of 3 A/m, leading to an increase in μ′. The μ′ obeys a Rayleigh law at the temperature below 343 K or under DC field of less than 4.22×10⁴ A/m. The Rayleigh constant η increases from 5.45×10⁻² to 1.54×10⁻¹ (A/m)⁻¹ as the temperature rises from 293 to 343 K, and η decreases from 5.58×10⁻² to 3.67×10⁻² (A/m)⁻¹ with increasing DC field from 1.99×10³ to 4.22×10⁴ A/m.     

Rayleigh scattering by sodium vapour in flames

In this paper we report on Rayleigh scattering measurements of sodium on the Na D-doublet in several premixed, laminar, shielded H₂/O₂/N₂, H₂/O₂/Ar and C₂H₂/O₂/N₂ flames at one atm. We performed the measurements under non-saturation conditions. The tunable CW dye-laser used produced linearly polarized light. The laser frequency was tuned well outside the absorption-line width of the sodium D-doublet lines. We have compared the ratio of Rayleigh scattering to collison-induced resonance-fluorescence (measured at fixed detunings of the laser) with theoretical predictions. In some flames, we also measured Rayleigh scattering and its polarization, as a function of detuning of the laser in the 4–40 Å region, for the red Na-D₁ and the blue Na-D₂ wings and found good agreement with theoretical predictions. Polarization of collision-induced fluorescence did not exceed 4% in this wavelength range.     

An electrochemical investigation of Li intercalation in the sol-gel LiMn2O4 spinel oxide

An alternative approach for obtaining the LiMn₂O₄ spinel phase is provided by the use of the sol-gel method in aqueous solution. The main electrochemical properties of the sol-gel LiMn₂O₄ phase are reported. In addition to chronopotentiometric and voltammetric experiments, the kinetics of the electrochemical insertion–extraction of lithium in Li_xMn₂O₄ (0.25<x<1) has been investigated using ac impedance spectroscopy. The strong variation of the chemical diffusion coefficient D_Li vs x, in the range 10⁻⁸–10⁻¹¹ cm² s⁻¹ (D_Li is found to be maximum for x=0.55) is critically discussed.     

The third-order optical nonlinearity of The pyrochlore phase 0.7Pb(Mg1/3Nb2/3)O3–0.3PbTiO3 thin film on quartz

The xPb(Mg_1/3Nb_2/3)O₃–(1−x)PbTiO₃ (PMNT) (with x=0.7) thin film is prepared on quartz substrates prepared using a sol–gel process. The PMNT thin film has a well-crystallized pyrochlore phase structure. The sign and magnitude of both real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ of the thin film have been determined by the Z-scan technique performed at 800 nm with a femtosecond laser. The nonlinear refraction index coefficient γ, the nonlinear absorption coefficient β of the thin film are 1.37×10⁻¹² cm²/W and −6.73×10⁻⁸ m/W, respectively. The real and imaginary part of the third-order nonlinear susceptibility of the film are 1.06×10⁻¹⁷ and −1.65×10⁻¹⁹ m²/V², respectively. The results suggested that the nonlinearity is dominated by the refractive for the film.     

Optical constants of Tl4Ga3InSe8 layered single crystals

The optical properties of Tl₄Ga₃InSe₈ layered single crystals have been studied by means of transmission and reflection measurements in the wavelength range of 500–1100 nm. The analysis of the room temperature absorption data revealed the presence of both optical indirect and direct transitions with band gap energies of 1.94 and 2.20 eV, respectively. Transmission measurements carried out in the temperature range of 10–300 K revealed that the rate of change of the indirect band gap with temperature is γ=−4.1×10⁻⁴ eV/K. The absolute zero value of the band gap energy was obtained as E_gi(0)=2.03 eV. The dispersion of the refractive index is discussed in terms of the Wemple–DiDomenico single-effective-oscillator model. The refractive index dispersion parameters: oscillator energy, dispersion energy, oscillator strength and zero-frequency refractive index were found to be 4.10 eV, 23.17 eV, 6.21×10¹³ m⁻² and 2.58, respectively. From X-ray powder diffraction study, the parameters of monoclinic unit cell were determined.