Influence of B site substituent Ti on the structure and thermophysical properties of A2B2O7-type pyrochlore Gd2Zr2O7

Since the structural integrity of A₂B₂O₇-type pyrochlores relies mostly on the interconnecting BO₆ octahedra, Ti⁴⁺ was selected to partially substitute Zr⁴⁺ in Gd₂Zr₂O₇ in order to distort the pyrochlore structure in order to improve the material’s thermophysical properties for potential use as high-temperature thermal insulation. As evidenced by X-ray diffraction and Raman spectroscopy studies, incorporation of Ti⁴⁺ simultaneously leads to long-range ordering of the pyrochlore structure as well as local lattice distortion. These two effects have been shown to be competitive in determining the crystal energy of the Gd₂(Zr_1−xTi_x)₂O₇ series and result in a minimum value of the Young’s modulus at x = 0.3 and a maximum value of the coefficient of thermal expansion at x = 0.2. At lower temperatures, the thermal conductivity of Gd₂Zr₂O₇ was significantly reduced by Ti⁴⁺ doping, and its composition dependence was accurately modeled by taking into account the phonon scattering by mass and strain fluctuations at the B site.     

Thermoelectric properties of Sn1−x−yTiySbxO2 ceramics

Thermoelectric properties of Sn_1−x−yTi_y Sb_xO₂ ceramics were investigated in detail. The addition of Sb into SnO₂ matrix increased the electric conductivity, σ. The increase in the σ value should be caused by the increase in the carrier concentration. The Seebeck coefficients of all the samples were negative, which means that these samples have n-type conduction. The samples of this study have porous structure. The maximum Z value of all the samples measured in this study was 2.4 × 10⁻⁵ K⁻¹.     

Magnetic and structural properties of the chromium-based Mn1−xCdxCr2S4 thiospinel

The (Mn_1−xCd_x)Cr₂S₄ phases (0 ≤ x ≤ 0.6) have been synthesized from the corresponding elements at 1123 K. These samples were characterized by powder X-ray diffraction (XRD) and magnetic susceptibility. The (Mn_1−xCd_x)Cr₂S₄ compounds crystallize in the space group Fd-3m with cell parameters a = 10.101(6) Å, 10.139(3) Å, 10.165(2) Å, and 10.192(1) Å for x = 0, 0.2, 0.4 and 0.6, respectively. An overall ferrimagnetic behavior is observed for all samples. The ferromagnetic component increases rapidly when manganese is substituted by non-magnetic cadmium, as shown by ZFC/FC measurements. At the same time, the value of the magnetization M₅₀ at 50 kOe, deduced from M(H) loops, also increases with increasing cadmium content because the antiferromagnetic alignment between chromium and manganese spins is progressively lost, leading toward well aligned moments pointing into the same direction. These results are explained by a rearrangement of the chromium spins when Mn located at the tetrahedral sites, is substituted by Cd.     

Thermoelectric properties of hot-pressed Zn4Sb3−xTex

A series of samples have been fabricated through vacuum melting method followed by hot-pressing for Zn₄Sb_3−xTe_x (x = 0.02–0.08), XRD patterns indicated that all the samples were single-phased β-Zn₄Sb₃. Electrical conductivity and Seebeck coefficient were evaluated in the temperature range of 300–700 K, showing p-type conduction. The thermoelectric figure of merit (ZT) was increased with the increase of Te content. ZT values of 0.8 and 1.0 were obtained at 673 K for Zn_4.08Sb₃ and Zn₄Sb_2.92Te_0.08, respectively.     

Studies on structural and electrical properties of Co1−xNixFe1.9Mn0.1O4 ferrite

Nickel-doped iron-deficient cobalt ferrite with small amount of manganese having the chemical composition Co_1−xNi_xFe_1.9Mn_0.1O₄, with x = 0.2, 0.4, 0.6 and 0.8, were prepared by standard double sintering ceramic method. The spinel phase formation was confirmed by X-ray diffraction (XRD). The DC resistivity measurements with temperature indicate a semiconducting behavior showing a linear decrease with increasing temperature and the doping of Ni enhances the resistivity. Maximum resistivity of the order of 10⁹ Ω cm was found for composition x = 0.8. Room temperature dielectric constant measurements with frequency (100 Hz to 1 MHz), show usual dielectric dispersion. Also, the variation of room temperature AC conductivity as a function of frequency were studied and explained by using Maxwell–Wagner two-layer model. The studies on dielectric constant (′), loss tangent (tan δ) and AC conductivity (σ_AC), at four different frequencies (viz., 1, 10, 100 kHz and 1 MHz), with temperature were made.     

Investigation of the dependency of the upper critical magnetic field on the content x in Y1−xYbx/2Gdx/2Ba2Cu3O7−y superconducting structures

The Y_1−xYb_x/2Gd_x/2Ba₂Cu₃O_7−y superconducting samples for x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0 were prepared by using the solid-state reaction technique. Resistivity measurements of the samples were performed in QD–PPMS system under different magnetic fields up to 5 T in zero fields cooling regime. Using the resistivity data, the upper critical magnetic field H_c2(0) at T = 0 K for 50% of R_n was calculated by the extrapolation H_c2(T) to the temperature T = 0 K. The coherence length in T = 0 K were calculated from H_c2(0) and the effects of x in the composition on both the coherence length and the upper critical magnetic field were examined. The results showed that H_c2(0) varied from 84.05 to 122.26 T with the content x. The upper critical magnetic field in the temperature T = 0 K slightly decreased with increasing the content x. Using the content x, the upper critical magnetic field can be controlled and this can be used in the superconductivity applications.     

Crystal structure of Nax(MoO)5(P2O7)4 studied by synchrotron X-ray diffraction

The crystal structure of sodium pentamolybdyl tetradiphosphate Na_x(MoO)₅(P₂O₇)₄ has been determined from synchrotron diffraction data collected at 293 K on two microcrystals. The compound crystallizes in a monoclinic space group I 1 1 2/a (no. 15, setting 11), with unit cell parameters a = 22.905(3), b = 23.069(2), c = 4.8537(2) Å, γ = 90.641(9)° and a = 22.898(3), b = 23.056(2), c = 4.8551(2) Å, γ = 90.82(1)°, for crystals I and II, respectively. The structure is pseudo-tetragonal, and the crystals are pseudo-merohedrally twinned by 90° rotation around the c-axis. The structure closely resembles the previously reported Li-deintercalated Mo_1.3OP₂O₇ [V.V. Lisnyak, N.V. Stus, P. Popovich, D.A. Stratiychuk, Ya. Filinchuk, V.M. Davydov, J. Alloys Compd. 360 (2003) 81–84]. Comparison of the two structures led us to conclude that the Mo₂ and Mo₃ clusters were erroneously identified in Mo_1.3OP₂O₇. A revised structure of Mo_1.3OP₂O₇ contains a fully occupied oxygen site instead of the 16% occupied Mo(2) site, thus the revised formulae for the Li-deintercalated compound is (MoO)₅(P₂O₇)₄. In both structures, the (MoO)₅(P₂O₇)₄ framework strongly resembles the one in the earlier reported Ag(MoO)₅(P₂O₇)₄, while the location of Na and Ag atoms differ.     

Substrates effect on Zn1−xMnxO thin films grown by RF magnetron sputtering

In this paper, we have presented the surface effect of the substrates on Mn doped ZnO (Zn_1−xMn_xO) thin films grown on Si(1 0 0) and sapphire [i.e. Al₂O₃(0 0 0 1)] by RF magnetron sputtering. These grown films have been characterized by X-ray diffraction (XRD), photoluminescence (PL) and vibrating sample magnetometer (VSM) to know its structural, optical and magnetic properties. All these properties have been found to be strongly influenced by the substrate surface on which the films have been deposited. The XRD results show that the Mn doped ZnO films deposited on Si(1 0 0) exhibit a polycrystalline nature whereas the films on sapphire substrate have only (0 0 2) preferential orientations indicating that the films are single crystalline. The studies of room temperature PL spectra reveal that the Zn_1−xMn_xO/Si(1 0 0) system is under severe compressive strain while the strain is almost relaxed in Zn_1−xMn_xO/Al₂O₃(0 0 0 1) system. It has been observed from VSM studies that Zn_1−xMn_xO/Al₂O₃(0 0 0 1) system shows ferromagnetic nature while the paramagnetic behaviour observed in Zn_1−xMn_xO/Si(1 0 0) system.     

Studies on structural and thermal expansion properties of Ho2−xLnxMo4O15 (Ln = Er, Sm and Ce) solid solutions

Three new series of Ho_2−xEr_xMo₄O₁₅ (x = 0.0–2.0), Ho_2−xSm_xMo₄O₁₅ (x = 0.0–0.6) and Ho_2−xCe_xMo₄O₁₅ (x = 0.0–0.25) solid solutions have been prepared successfully by solid-state reaction and studied by powder X-ray diffraction. All the XRD patterns of these molybdates can be indexed in monoclinic space group P2₁/c. Lattice parameters a, b and c of Ho_2−xLn_xMo₄O₁₅ decrease linearly with increasing erbium content and increase with increasing samarium or cerium content. Thermal expansion behaviors of Ho_2−xLn_xMo₄O₁₅ have been investigated in the 25–500 °C temperature range with high-temperature X-ray diffraction. The temperature dependence of Mo(2)–O14 interaction looks like to be responsible for their thermal expansion behaviors.     

The role of valence electron concentration in the cohesive properties of YBxN1−x, YCxN1−x and YNxO1−x compounds

The mechanical properties are not yet understood at basic levels. Previous works shows that the greatest hardness for rock-salt structures (such as TiC_xN_1−x) is attained for a valence electron concentration (VEC) of 4.2 electrons per atom. The present work is aimed to explore this concept for yttrium-based compounds. By means of first principles calculations we did a systematical investigation where nitrogen in YN (VEC = 4) was supplanted by either of B, C or O to reduce or increase its VEC, forming YB_xN_1−x, YC_xN_1−x and YN_1−xO_x ternary compounds. We have calculated the cohesive energy (E_O), cell volume (V_O), bulk modulus (B_O) and density of states (DoS) as a function of VEC. The Fermi level (E_f,) is shifted toward the valence band by substituting B or C in YN, and toward the conduction band by means of O. It is concluded that the optimal position for E_f (maximum B_O) is linked to the saturation of electronic states with e_g-symmetry. At this point the excess of electrons provided by O starts filling antibonding states with t_2g-symmetry. That is, B_O increases monotonically as a function of VEC until VEC  4.1, after that point B_O decrease.     

Structural, magnetic and electrical properties of (La0.70−xNdx)Sr0.30Mn0.70Cr0.30O3 with 0 ≤ x ≤ 0.30

The structural, magnetic and electrical properties of (La_0.70−xNd_x)Sr_0.30Mn_0.70Cr_0.30O₃ perovskites (0 ≤ x ≤ 0.30) prepared by the usual ceramic procedure were investigated. Structural Rietveld refinement revealed that these compounds crystallize in a rhombohedral perovskite structure when x = 0, 0.10 and 0.20, while for x = 0.30 the structure becomes orthorhombic (Pbnm). It was found that the substitution of La by Nd reduces the Curie temperature (T_C). The FC, ZFC, M(H) and AC susceptibility measurements show typical canted-antiferromagnetism for the Nd-doped samples, in which a ferromagnetic component coexists with predominant antiferromagnetic interactions. The values of the magnetization (M(H)) decrease very slightly when increasing the Nd content, compared to the undoped sample (M_S values at 5 T and 2 K are, respectively, 47.9, 47.3 and 47.5 emu/g for x = 0.10, 0.20 and 0.30, compared to 48.2 emu/g for x = 0), indicating that the Nd³⁺ contribution is negligible compared to the total moment of the ferromagnetic (Mn/Cr) network. The resistivity increases by several orders of magnitude with Nd-doping and the semi-conducting behaviour persists in the whole temperature range. The interaction between Mn⁴⁺–O–Cr³⁺and Cr³⁺–O–Cr³⁺ is responsible for the semi-conducting state.     

Self-propagating high-temperature synthesis with post-heat treatment of La1−xSrxFeO3 (x = 0–1) perovskite as catalyst for soot combustion

La_1−xSr_xFeO₃ (x = 0–1) perovskite, Sr-substituted LaFeO₃, was prepared by Self-propagating high-temperature synthesis (SHS) and its catalytic activity for soot combustion was experimentally examined in comparison with that of a conventional Pt/Al₂O₃ catalyst. The products were also characterized by XRD, FE-SEM, and BET specific surface area. The XRD analysis revealed that all the products had a perovskite phase as the major compound, together with intermediate phases with higher x values (x = 0.7–1). The BET specific surface area of the products increased with x. Moreover, the catalytic activity for soot combustion also increased with x, wherein the BET specific surface area appeared an appropriate index for explaining the observed activity. The sample with x = 0.8 exhibited the highest activity for soot combustion among all the SHS products. The soot combustion temperature of this product was as much as 100 °C lower than that of non-catalytic soot combustion. In other words, it had the same activity as that at only 20 °C higher, in comparison to conventional Pt/Al₂O₃ catalyst. More significantly, average apparent activation energy of sample with x = 0.8 calculated by Friedman method using TG/DTA was approximately 15 kJ/mol lower than that of Pt/Al₂O₃ catalyst. This result suggested that La_1−xSr_xFeO₃ has the possibility to be an alternative catalyst to Pt/Al₂O₃ catalyst.     

Influence of Co substitution on magnetoelastic properties of Er2Fe14−xCoxB (x = 1, 3 and 5) intermetallic compounds

The magnetostriction and thermal expansion of Er₂Fe_14−xCo_xB (x = 1, 3 and 5) intermetallic compounds were measured, using the strain gauge method in the temperature range 75–450 K under applied magnetic fields up to 1.5 T. For all samples the longitudinal magnetostriction (λ_l) undergoes an anomaly around the spin reorientation temperature (T_SR). It is also observed that λ_l decreases with increasing the Co content. All compounds show saturation type behaviour in their anisotropic magnetostriction curves at different temperatures and applied fields. The saturation behaviour of the compound with x = 3 occurs at higher temperatures than with x = 1 and 5. The volume magnetostriction strongly increases below μ₀H = 0.3 T, then monotonically rises with applied field up to the spin reorientation temperature. An invar type behaviour is observed above 200 K in the compound with x = 1. The results are discussed based on the temperature dependence of magnetocrystalline anisotropy of compounds below and above their T_SR.     

Structural, magnetic and electrical transport properties for a series of La1−xSrxFe1−xMnxO3 (0.3 ≤ x ≤ 0.7) compounds

The structural, electrical transport and magnetic properties have been studied for compounds: La_1−xSr_xFe_1−xMn_xO₃ (0.3 ≤ x ≤ 0.7). The lattice parameter, a, first decreases with x, and followed by an increase when Sr²⁺ and Mn⁴⁺ was continuously doped. The cell parameters, b and c, slightly decrease with coupled substitution of Sr²⁺ for La³⁺ and Mn⁴⁺ for Fe³⁺. In the paramagnetic temperature range, formation of magnetic clusters is suggested; the sizes of clusters decrease with x up to 0.5, following that they increase sharply with continuing doping. The electrical behaviors of all specimens demonstrate insulators and the electrical resistivity increases with content of Mn⁴⁺ and Sr²⁺ ions doped. A variable range hopping model is suitable to describe electrical transport process for the compounds at low temperature. At high temperature the electrical transport process can be described by bipolaron model for all compounds.     

Synthesis, characterization and magnetic properties of complex oxides Ln2Mn2/3Re4/3O7 (Ln = Er, Y) and Y2Zn2/3Re4/3O7

Complex oxides Ln₂Mn_2/3Re_4/3O₇ (Ln = Y, Er) and Y₂Zn_2/3Re_4/3O₇ with a zirkelite structure and hexagonal unit cells (space group P3₁21, z = 6) have been obtained. Static and dynamic magnetic susceptibility measurements show that these oxides possess spin-glass behavior at low temperatures. Valence combinations of d-metals in the oxides are Mn²⁺(Zn²⁺)–Re⁵⁺. It is supposed that the examined specimens Ln₂Mn_2/3Re_4/3O₇ (Ln = Y, Er) contain the second magnetic phase of an unknown composition.     

A polyethylene glycol-assisted route to synthesize Pb(Ni1/3Nb2/3)O3-PbTiO3 in pure perovskite phase

Ferroelectric relaxors (1 − x)Pb(Ni_1/3Nb_2/3)O_3−xPbTiO₃ (PNN-PT) with a composition (x = 0.36) near the morphotropic phase boundary (MPB) were prepared by a polyethylene glycol (PEG)-assisted solid-state reaction route. PEG with a molecular weight of 200 was introduced during the ball milling process of the raw oxide powders. XRD and TG/DSC results demonstrated that the interaction between PbO and PEG favors the transformation of lead-rich pyrochlore to lead-deficient pyrochlore, thus facilitating the formation of perovskite phase. Consequently, pure perovskite powders were synthesized at a relatively low temperature of 850 °C. Ceramics fabricated with the PEG-assisted route show a room temperature dielectric constant of 4987 and a maximum dielectric constant (at T_max) of 24,307 at a frequency of 1 kHz. The piezoelectric constant d₃₃ measured was 460 pC/N.     

Thermoelectric properties of novel skutterudites with didymium: DDy(Fe1−xCox)4Sb12 and DDy(Fe1−xNix)4Sb12

In order to improve the thermoelectric properties via efficient phonon scattering Didymium (DD), a mixture of Pr and Nd, was used as a new filler in ternary skutterudites (Fe_1−xCo_x)₄Sb₁₂ and (Fe_1−xNi_x)₄Sb₁₂. DD-filling levels have been determined from combined data of X-ray powder diffraction and electron microprobe analyses (EMPA). Thermoelectric properties have been characterized by measurements of electrical resistivity, thermopower and thermal conductivity in the temperature range from 4.3 to 800 K. The effect of nanostructuring in DD_0.4Fe₂Co₂Sb₁₂ was elucidated from a comparison of both micro-powder (ground in a WC-mortar, 10 μm) and nano-powder (ball-milled, 150 nm), both hot pressed under identical conditions. The figure of merit ZT depends on the Fe/Co and Ni/Co-contents, respectively, reaching ZT > 1. At low temperatures the nanostructured material exhibits a higher thermoelectric figure of merit. The Vickers hardness was measured for all samples being higher for the nanostructured material.     

A substitution of nickel by antimony:: Crystal and electronic structure of the new antimonide Hf6Ni1−xSb2+x

The ternary antimonides Hf₆M_1−xSb_2+x (M=Fe, Co, Ni) were prepared by arc-melting of stoichiometric mixtures of Hf, HfSb₂ and M. According to the single crystal structure analyses, performed on Hf₆NiSb₂ and Hf₆Ni_0.76Sb_2.24, Hf₆M_1−xSb_2+x crystallizes in an ordered variant of the Fe₂P structure type with the M and Sb atoms occupying the two P positions on 1b and 2c of space group P

Full-size image

2m, respectively (Zr₆CoAl₂ type). The 3d metal atoms M can partially be replaced by antimony, leading to significant, anisotropic changes in the lattice dimensions which are a=765.6(1) pm, c=362.10(7) pm, V=183.81(5)×10⁶pm³ for Hf₆NiSb₂, and a=760.5(1) pm, c=372.40(7) pm, V=186.53(5)×10⁶pm³ for Hf₆Ni_0.76Sb_2.24 as determined by single crystal data. Calculations of the electronic structure of Hf₆NiSb₂ using the Extended Hückel approximation show strong bonding Hf–Hf, Hf–Ni, and Hf–Sb interactions.     

Effect of potassium doping on the structural, magnetic and magnetocaloric properties of La0.7Sr0.3−xKxMnO3 perovskite manganites

We investigate the effect of potassium doping on the structural, magnetic and magnetocaloric properties of La_0.7Sr_0.3−xK_xMnO₃ (x = 0.05, 0.1, 0.15 and 0.2) powder samples. Our polycrystalline compounds were synthesized using the solid-state reaction at high temperature. X-ray diffraction characterizations showed that all our studied samples crystallize in the distorted rhombohedral system with space group. With increasing potassium content, the unit cell volume exhibits a broad maximum around x = 0.15. Magnetization measurements versus temperature showed that all our samples exhibit a paramagnetic to ferromagnetic transition with decreasing temperature. The Curie temperature T_C is found to decrease from 365 K for x = 0 to 328 K for x = 0.2 as well as the saturated magnetization M_sp which shifts from 3.68 μ_B/Mn for x = 0 to 3.05 μ_B/Mn for x = 0.2. The critical exponent γ defined as M_sp (T) = M_sp(0)[1−(T/T_C)]^γ is found to remain almost constant and equal to 0.33 for all our samples. The maximum of magnetic entropy changes |ΔS_max| of La_0.7Sr_0.3−xK_xMnO₃ for x = 0.05 and 0.15 is found to be respectively, 1.37 and 1.2 J kg⁻¹ K⁻¹ under a magnetic field change of 1 T.     

X-ray diffraction study of Ba0.985Na0.015Ti0.985Nb0.015O3, Ba0.6Na0.4Ti0.6Nb0.4O3 and Ba0.3Na0.7Ti0.3Nb0.7O3 compositions

The Ba_0.985Na_0.015Ti_0.985Nb_0.015O₃, Ba_0.6Na_0.4Ti_0.6Nb_0.4O₃ and Ba_0.3Na_0.7Ti_0.3Nb_0.7O₃ compositions of the (1 − x) BaTiO₃–xNaNbO₃ (BTNNx) system have been studied by X-ray diffraction and by measurements of dielectric properties. The specimens with composition BTNN (x = 0.015, 0.40 and 0.70) have been refined by the JANA program from X-ray powder diffraction data. Ceramic samples with composition (1 − x) BaTiO₃ + xNaNbO₃ (where x = 0.015, 0.40 and 0.70) were prepared by calcinations from appropriate mixture of BaCO₃, TiO₂, Na₂CO₃ and Nb₂O₅. The calcined powder was sintered at temperature range 1200–1400 °C. As the composition x increased from 0.015 (and 0.70), the ferroelectric ceramics (x = 0.015, FE) with tetragonal phase changed to the ferroelectric relaxors (RFE, x = 0.40). RFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to 180 K) due to a frustration between RFE and FE state. These ceramics present the classical ferroelectric character when 0 ≤ x < 0.075 and 0.55 < x ≤ 1 and relaxor character when 0.075 ≤ x ≤ 0.55.