Kinetic study of nitrate reduction on Pt(1 1 0) electrode in perchloric acid solution

The kinetics of electrocatalytic reduction of nitrate on Pt(1 1 0) in perchloric acid was studied with cyclic voltammetry at a very low sweep rate of 1 mV s⁻¹, where pseudo-steady state condition was assumed to be achieved at each electrode potential. Stationary current-potential curves in perchloric acid in the absence of nitrate showed two peaks at 0.13 V and 0.23 V (RHE) in the so-called adsorbed hydrogen region. The nitrate reduction proceeded in the potential region of the latter peak in the pH range studied. The reaction orders with respect to NO₃⁻ and H⁺ were observed to be close to 0 and 1, respectively. The former value means that the adsorbed NO₃⁻ at a saturated coverage is one of the reactants in the rate-determining step (rds). The latter value means that hydrogen species is also a reactant above or on the rds. The Tafel slope of nitrate reduction was −66 mV per decade, which is taken to be approximately −59 mV per decade, indicating that the rds is a pure chemical reaction following electron transfer. We discuss two possible reaction schemes including bimolecular and monomolecular reactions in the rds to explain the kinetics and suggest that the reactants in the rds are adsorbed hydrogen and adsorbed NO₃⁻ with the assistance of the results in our recent report for nitrate reduction on Pt(S)[n(1 1 1) × (1 1 1)] electrodes: the nitrate reduction mechanism can be classified within the framework of the Langmuir-Hinshelwood mechanism.     

Electrochemical characterization of irreversibly adsorbed germanium on platinum stepped surfaces vicinal to Pt(1 0 0)

The electrochemical behavior of germanium irreversibly adsorbed at stepped surfaces vicinal to the Pt(1 0 0) pole is reported. The process taking part on the (1 0 0) terraces is evaluated from charge density measurements and calibration lines versus the terrace dimension are plotted. On the series Pt(2n − 1,1,1) having (1 1 1) monoatomic steps, the charge involved in the redox process undergone by the irreversibly adsorbed germanium is able to account for (n − 0.5) terrace atoms, thus suggesting some steric difficulties in the growth of the adlayer on the (1 0 0) terraces. Conversely, no steric problems are apparent in the series Pt(n,1,0) in which more open (1 0 0) steps are present on the (1 0 0) terraces. In this latter case the charge density under the germanium redox peaks is proportional to the number of terrace atoms. Some comparison is made with other stepped surfaces to understand the behavior and stability of germanium irreversibly adsorbed on the different platinum surface sites.     

CO monolayer oxidation on stepped Pt(S) [(n − 1)(1 0 0) × (1 1 0)] surfaces

The electrochemical oxidation of CO has been studied on Pt(S)[(n − 1)(1 0 0) × (1 1 0)] electrodes to investigate the effect of the step density in the reaction. This series shows two different trends for long (n ≥ 7) and short terraces. For long terraces, the voltammetric peak shifts towards higher potential as the step density increases, unlike the behaviour observed for other stepped surfaces, which exhibit the opposite behaviour in agreement with the Smoluchowski effect. For short terraces, the “normal” behaviour is observed, that is, as the step density increases the peak shifts towards lower potentials. Chronoamperometric measurements were used to determine rate constants and Tafel slopes using the mean field Langmuir-Hinselwood kinetics. Rate constants follow the same trends as the peak potentials in voltammetry. A Tafel slope of 75 ± 4 mV has been obtained for the surfaces with long terraces whereas a value of the surfaces with short terraces showed a value of 100-120 mV is obtained. This change of slopes is interpreted as a change in the electrochemical behaviour of the species involved in the mechanism, probably, a change in the adsorption isotherm of adsorbed OH. Pt(5 1 0) electrode exhibits an intermediate behaviour between those of long and short terraces with two different peaks that can be associated with both behaviours previously described.     

Surface X-ray scattering of high index plane of platinum containing kink atoms in solid-liquid interface: Pt(3 1 0) = 3(1 0 0)-(1 1 0)

Surface structure of Pt(3 1 0) = 3(1 0 0)-(1 1 0), which contains kink atoms in the step, has been determined with the use of in situ surface X-ray scattering (SXS) in the double layer region (0.50 V(RHE)) in 0.1 M HClO₄. Clean Pt(3 1 0) surface has pseudo (1 × 1) structure on which lateral displacements of 2-9% and 0.3-1% are found along a and b directions, respectively, whereas the surfaces of Pt(1 1 0) = 2(1 1 1)-(1 1 1) and Pt(3 1 1) = 2(1 0 0)-(1 1 1) are reconstructed to (1 × 2) according to previous reports. Interlayer spacing between the first and the second layers d₁₂ is contracted about 5% compared with the bulk spacing, whereas those between underlying layers are expanded down to fourth layer. Fully adsorbed CO has no effect on the surface structure of Pt(3 1 0). This result differs from that on Pt(1 1 1), where d₁₂ is expanded after CO adsorption.     

Electroreduction of nitrate ions on Pt(1 1 1) electrodes modified by copper adatoms

Kinetics and mechanism of nitrate ion reduction on Pt(1 1 1) and Cu-modified Pt(1 1 1) electrodes have been studied by means of cyclic voltammetry, potentiostatic current transient technique and in situ FTIRS in solutions of perchloric and sulphuric acids to elucidate the role of the background anion. Modification of platinum surface with copper adatoms or small amount of 3D-Cu crystallites was performed using potential cycling between 0.05 and 0.3 V in solutions with low concentration of copper ions, this allowed us to vary coverage θ_Cu smoothly. Following desorption of copper during the potential sweep from 0.3 to 1.0 V allowed us to estimate actual coverage of Pt surface with Cu adatoms. Another manner of the modification was also applied: copper was electrochemically deposited at several constant potentials in solutions containing 10⁻⁵ or 10⁻⁴ M Cu²⁺ and 5 mM NaNO₃ with registration of current transients of copper deposition and nitrate reduction.It has been found that nitrate reduction at the Pt(1 1 1) surface modified by copper adatoms in sulphuric acid solutions is hindered as compared to pure platinum due to induced sulphate adsorption at E < 0.3 V. Sulphate blocks the adsorption sites on the platinum surface and/or islands of epitaxial Cu(1 × 1) monolayer thus hindering the adsorption of nitrate anions and their reduction. The extent of inhibition weakly depends on the copper adatom coverage. Deposition of a small amount of bulk copper does not affect noticeably the rate of nitrate reduction.Nitrate reduction on copper-modified Pt(1 1 1) electrodes in perchloric acid solutions occurs much faster as compared to pure platinum. The steady-state currents are higher by 4 and 2 orders of magnitude at the potentials of 0.12 and 0.3 V, respectively. The catalytic effect of copper adatoms is largely caused by the facilitation of nitrate adsorption on the platinum surface near Cu_ad and/or on the islands of the Cu(1 × 1) monolayer (induced nitrate adsorption).Hydrogen adatoms block the adsorption sites on platinum for NO₃⁻ anion adsorption and inhibit reactions of nitrate reduction even at moderate surface coverage.The products of nitrate reduction in sulphuric and perchloric acids are essentially the same (NO and ammonia) irrespective of the presence or absence of Cu on the platinum surface.     

Adsorption behavior of acetonitrile on platinum and gold electrodes of various structures in solution of 0.5 M H2SO4

The variation of electrode nature and surface structure (the use of stepped single crystal faces with controlled width of (1 1 1) terraces and monoatomic steps of (1 0 0) or (1 1 0) orientation) allows to determine peculiarities of co-adsorption of acetonitrile molecules, hydrogen adatoms and (bi)sulfate anions. It has been shown that first of all acetonitrile blocks adsorption sites at the steps. Anion adsorption at terraces of stepped platinum surfaces in 0.5 M H₂SO₄ solution with additions of acetonitrile depends on terrace width and the step orientation. This demonstrates the important role of structural factors in competitive adsorption processes. The decrease in adsorption of hydrogen and anions on narrow terraces is substantially due to the influence of acetonitrile molecules placed at the steps or nearby sites. At E < 1.0 V, electrochemical conversion of acetonitrile has not been detected at single crystal Pt surfaces. However, acetonitrile oxidation might proceed on polycrystalline platinum followed by product desorption. On Au(1 1 1) surface acetonitrile adsorption is considerably weaker than that on platinum electrodes.     

Carbon monoxide oxidation on Au(1 1 1) surface decorated by spontaneously deposited Pt

Platinum is deposited spontaneously on Au(1 1 1) surface from 1 mM H₂PtCl₆ + 1 M HClO₄ solution using multiple deposition procedure. X-ray photoelectron spectroscopy (XPS) analysis has shown that after immersion into the Pt containing solution and rinsing with water, Pt(OH)₂ resides on the Au(1 1 1) substrate. Consecutive depositions as well as in situ scanning tunneling microscopy (STM) and electrochemical measurements are performed on previously electrochemically reduced Pt/Au(1 1 1) surfaces. Only homogeneous distribution of thus deposited Pt islands is observed by in situ STM. With subsequent depositions, the width of deposited Pt islands increases, but stays lower than 10 nm, while a significant increase of Pt islands height is observed, leading to moderate increase of the coverage. Cyclic voltammetry (CV) profiles of obtained Pt/Au(1 1 1) surfaces, and CO stripping curves are recorded in 0.5 M H₂SO₄ solution. CO oxidation takes place only at higher potentials shifting negatively with increasing coverage. This is discussed with respect to Pt islands width and height distributions and to the influence of the Au(1 1 1) substrate surface.     

B3LYP study of water adsorption on cluster models of Pt(1 1 1), Pt(1 0 0) and Pt(1 1 0): Effect of applied electric field

A density functional theory (DFT) study of the adsorption of a water molecule on Pt(1 1 1), Pt(1 0 0) and Pt(1 1 0) surfaces has been carried out using cluster models, at the B3LYP/LANL2DZ,6-311++G(d,p) level. The water molecule binds preferentially at the top site on Pt(1 1 1) and Pt(1 0 0) with adsorption energy around −27 kJ mol⁻¹, and is oriented with the molecular plane nearly parallel to the metal surface and the H atoms pointing away from it. On Pt(1 1 0) a hollow site is preferred, with adsorption energy of −32 kJ mol⁻¹. Potential energy barriers for the rotation around an axis normal to the surface have been estimated to be below 1 kJ mol⁻¹ for Pt(1 1 1) and Pt(1 0 0) when water is adsorbed on top. Upon application of an external electric field (inducing positive charge density on the metal) adsorbed water is additionally stabilized on the three surfaces, especially at the top adsorption site, and adsorption on Pt(1 1 1) and Pt(1 0 0) becomes more favoured than on Pt(1 1 0). Good agreement has been found between harmonic vibrational frequencies calculated at the B3LYP/LANL2DZ,6-311++G(d,p) level and experimental frequencies for adsorbed water monomers on Pt(h k l) surfaces.     

Electrochemical characterization of kinked Pt(7 5 1) surface in acidic media

Kinked Pt(7 5 1) surface was prepared and its electrochemical behaviors under different pretreatment conditions in acidic media were investigated systematically by using cyclic voltammetry. The results demonstrated that the upper limit of potential scanning and cooling atmospheres after the Pt(7 5 1) having been flame-annealed significantly influence the voltammetric behavior of Pt(7 5 1) electrode. The electric charge of hydrogen adsorption-desorption slightly increases with increasing the upper limit of potential scanning. Different cooling atmospheres give rise impacts to the surface structure of Pt(7 5 1) electrode, but hardly change the amount of hydrogen adsorption-desorption sites on the electrode. In addition, the so-called third oxidation peak appears near −0.08 V in H₂SO₄ media and −0.05 V in HClO₄ solution because of the presence of (1 1 0) terrace sites on this surface, and a plausible mechanism for the formation of this current peak is discussed. The results are of importance in understanding the electroadsorption properties of the kinked Pt(7 5 1) surface, as well as in further exploration of this kinked electrode in electrocatalysis.     

Determination of the step dipole moment and the step line tension on Ag(0 0 1) electrodes

Using impedance spectroscopy, we determined the step dipole moment and the potential dependence of the step line tension of silver electrodes in contact with an electrolyte: (0 0 1) and vicinal surfaces (1 1 n) with n = 5, 7, 11 in 10 mM ClO₄⁻-solutions were investigated. The step dipole moment is determined from the shift of the potential of zero charge (pzc) as a function of the surface step density. The dipole moment per step atom was found to be 3.5 ± 0.5 × 10⁻³ e Å. From the pzc and the potential dependence of the capacitance curves, the potential dependence of the surface tension of the vicinal surfaces is determined. The line tension of the steps is then calculated from the difference between the surface tensions of stepped (1 1 n) and the nominally step-free (0 0 1) surfaces. The results are compared to a previous study on Au(1 1 n) surfaces. For gold, the step line tension decreases roughly linear with potential, whereas a parabolic shape is observed for silver.     

Oxygen electroreduction on Ag(1 1 1): The pH effect

The rotating ring disk method (RRDE) is applied to investigate the pH effect on oxygen reduction reaction (ORR) on Ag(1 1 1) single crystal surface in 0.1 M KOH and 0.1 M HClO₄. In 0.1 M KOH, the ORR proceeds through 4e⁻ reaction pathway with a very small (0.5-2.5%) peroxide formation in the entire potential range. In 0.1 M HClO₄ the onset potential for the ORR is shifted for ca. 400 mV toward the higher overpotentials compared to the 0.1 M KOH solution. At the low overpotentials, in 0.1 M HClO₄ the ORR proceeds entirely as a 2e⁻ process, i.e, 100% H₂O₂ formation. At higher overpotentials, the initial mixed a 2e⁻ and 4e⁻ reduction is followed by the potential region where the ORR proceeds entirely as a 4e⁻ process, with H₂O formation as a final product. The pH dependent shift in the onset of the ORR as well as the reaction pathway has been explained based on both: a thermodynamic analysis of pH independent rate determining step, and on the pH dependent change in availability of surface active sites and adsorption energies of molecular oxygen and reaction intermediates.     

In situ radiotracer and voltammetric study of the formation of surface adlayers in the course of Cr(VI) reduction on polycrystalline and (1 1 1) oriented platinum

This paper is focused on the in situ radiotracer and voltammetric studies of the induced HSO₄⁻/SO₄²⁻ adsorption at Pt(poly) and Pt(1 1 1) surfaces in 0.1 mol dm⁻³ HClO₄ solution in the course of Cr(VI) electroreduction. Besides this, the sorption behavior of HSO₄⁻/SO₄²⁻ ions on bare Pt(poly) and Pt(1 1 1) electrodes is compared and discussed. From the experimental results it can be stated that: (i) although the extent of bisulfate/sulfate adsorption is strongly dependent upon the crystallographic orientation of Pt surfaces, the maximum coverage on the Pt(1 1 1) does not exceed 0.2 monolayer; (ii) the Cr(VI) electroreduction on both poly- and (1 1 1) oriented platinum proceeds via a ce (chemical-electron-transfer) mechanism to yield Pt surfaces covered with intermediate surface adlayers containing Cr(VI) particles (and reduced Cr-containing adspecies) and ‘strongly bonded’ HSO₄⁻/SO₄²⁻ ions; (iii) while the coverage of platinum surfaces by the intermediate complexes formed in the course of Cr(VI) electroreduction at E > 0.20 V is basically independent of the crystallographic orientation of the Pt electrode, the onset for rapid Cr(VI) reduction is highly affected by the nature and crystallographic orientation of the electrode.     

The adsorption of Sn on Pt(1 1 1) and its influence on CO adsorption as studied by XPS and FTIR

The coverage of Sn on Pt(1 1 1) which is obtained by electrochemical deposition from 5×10⁻⁵ M Sn²⁺ in 0.5 M H₂SO₄ has been determined by XPS for different deposition times. Complete suppression of hydrogen adsorption corresponds to a coverage of ?_max=0.35 (Sn to surface Pt atoms).Co-adsorption of CO with Sn on Pt(1 1 1) has been studied by FTIR spectroscopy. The IR spectra of the stretching vibration of CO can be interpreted in terms of the vibrational signature of the Pt(1 1 1)/CO system and no vibrational bands associated with CO on Sn are detected. At high Sn coverages, the 1840 cm⁻¹ band associated with bridge-bonded CO and the 2070 cm⁻¹ band assigned to on-top CO are present, however, no hollow site adsorption which is characterized by the 1780 cm⁻¹ band is revealed within the resolution of the experiment. This vibrational signature corresponds to a less compressed adlayer compared to the (2×2)-3CO saturation structure on Pt(1 1 1). At lower Sn coverages, signatures from both the compressed and the less compressed CO adlayer structures are seen in the spectra. From earlier structural and electrochemical studies it is known that Sn is adsorbed in 2D islands and influences CO molecules in its neighbourhood electronically. This leads to a disappearance of the IR band from CO adsorbed in the hollow site at high Sn coverages and to higher population of the weakly adsorbed state of CO for all Sn-modified surfaces, i.e. a relative increase of the amount of CO oxidised at low potentials. In addition to this electronic effect, Sn also exerts a co-catalytic effect at low Sn coverages on that part of CO which is adsorbed at a larger distance from Sn due to a bi-functional mechanism. The IR spectra shows for the Sn-modified Pt(1 1 1) surface that the transition from the compressed CO adlayer which is characterized by the hollow site adsorption of CO to the less compressed one which exhibits a characteristic band associated with bridge-bonded CO occurs already at 250 mV instead of 400 mV.     

Thermodynamic approach to the double layer capacity of a Pt(1 1 1) electrode in perchloric acid solutions

A thermodynamic method based on the work done by Frumkin and Petrii [A.N. Frumkin, O.A. Petrii, Electrochim. Acta 20 (1975) 347], to calculate the so-called double layer capacity for a Pt(1 1 1) electrode is proposed. The analysis requires careful measurement of the total charge density versus potential curves for a series of solutions with composition (0.1 − x) M KClO₄ + x M HClO₄. A method in which the total charge densities are determined by integration of cyclic voltammograms recorded in solutions with or without chloride is described. Following this procedure the double layer capacity curves were calculated. The double layer capacity curves displayed three peaks that were tentatively assigned to the solvent reorientation, onset of OH adsorption and completion of the OH adlayer. In the hydrogen adsorption region, the double layer capacity values were 14 ± 5 μF/cm², in good agreement with previous estimates reported in the literature by using other approaches.     

Dependence of electrocatalytic activity on film thickness for the hydrogen evolution reaction of Pd overlayers on Au(1 1 1)

The hydrogen evolution reaction has been studied for ultrathin Pd overlayers of various thickness on Au(1 1 1) in 0.1 M H₂SO₄. A clear correlation of the electrocatalytic activity as expressed by the exchange current density and the binding energy of adsorbed hydrogen has been found. While hydrogen is bound strongest on the second Pd monolayer (ML), the respective catalytic activity is poorest for all the surface structures under study. The exchange current density increases in the order 2 ML Pd < 1 ML Pd < bulk Pd (more than 2 ML). The electronic ligand effect, a geometric effect due to pseudomorphic growth and the surface defect density belong to the most crucial parameters in relations between structure of the electrode surface and its electrocatalytic activity. The experimental results are supported by an excellent agreement with theoretical predictions.     

In situ STM study of underpotential deposition of bismuth on Au(1 1 0) in perchloric acid solution

The underpotential deposition (UPD) of Bi on Au(1 1 0) was investigated in HClO₄ solution using in situ scanning tunneling microscopy. The UPD of Bi occurred in three steps. A structure, in which Bi atoms formed dimers, was found for the first UPD adlayer. A (1 × 1) image was obtained by STM at the second UPD peak. For the third UPD peak, Bi atoms formed an incommensurate adlayer, and stripes of Bi were observed on terraces. After the third UPD, a structural reconstruction caused by adsorbed Bi was observed.     

A TDS study of D adsorption on terraces and terrace edges of graphite (0 0 0 1) surfaces

Adsorption of thermal (2000 K) D atoms on (0 0 0 1) surfaces of various highly oriented pyrolytic graphite (HOPG) and natural graphite substrates was studied under ultra high vacuum (UHV) conditions with thermal desorption spectroscopy (TDS). D chemisorption on terrace and terrace edge sites of graphite (0 0 0 1) surfaces was identified. Recombinative desorption of D adsorbed on terraces was observed between 400 and 600 K. The analysis of TD spectra from various graphite surfaces reveals the existence of three desorption states intrinsic to graphite (0 0 0 1), and proposed as being due to adsorbate structures composed of one (monomer) and two neighbouring (dimer) chemisorbed D atoms, and aggregates thereof (mixed). The dimer structure is supposed to exhibit higher stability than the monomer. Reaction of D with terrace edges leads to the formation of CD, CD₂ and CD₃-groups at edge C atoms. These groups decompose during heating between 790 and 1300 K via release of gaseous D₂ and CD_x, C₂D_x and C₃D_x-hydrocarbons.     

Reactivity of monolayers and nano-islands of palladium on Au(1 1 1) with respect to proton reduction

Electrochemical reactivity regarding hydrogen reduction was studied at epitaxially grown Pd monolayers and sub-monolayers on Au(1 1 1) in 0.1 M HClO₄ solution. The rate of hydrogen evolution increases with decreasing numbers of layers, and it is considerably higher for sub-monolayers, i.e. the fewer Pd islands are on the surface the higher is the catalytic activity. No clear dependence of the reactivity on the ratio of Pd edge atoms to terrace atoms was found. Possible mechanisms explaining the experimental results are discussed.     

First principles mechanistic study of borohydride oxidation over the Pt(1 1 1) surface

The mechanism of borohydride oxidation and the competing hydrolysis reaction are examined over Pt(1 1 1) using density functional theory (DFT) methods. Adsorption of BH₄⁻ over Au(1 1 1) and Pt(1 1 1) is examined. Adsorption over Pt(1 1 1) is dissociative and extremely exothermic at potentials of interest, leading to a high surface coverage of H^* for which gaseous hydrogen evolution is competitive with oxidation. Elementary surface reactions oxidizing B-containing intermediates are favorable over Pt(1 1 1) at −0.85 V (SHE), consistent with experimental voltammetry results in the literature. The energetics of the initial adsorption step dictate the activity limitation of gold anodes and the selectivity limitation of platinum electrodes. This adsorption energy can be rapidly calculated with DFT methods, enabling screening of pure metals, alloys, poisons, and promoters to optimize borohydride oxidation catalyst design.     

In situ FTIR studies of the catalytic oxidation of ethanol on Pt(1 1 1) modified by bi-dimensional osmium nanoislands

This paper presents the study of ethanol electrooxidation on Pt(1 1 1) electrode modified by different coverage degrees of a submonolayer of osmium nanoislands, which were obtained by spontaneous deposition. The ethanol oxidation reaction was extensively studied by employing in situ FTIR. Collections of spectra of the ethanol adsorption and oxidation processes were acquired over a series of positive potential steps, in order to determine the intermediate species and the main products that are formed. It was shown that the increase in the catalytic activity of Pt(1 1 1) after osmium deposition for ethanol oxidation is greater than that observed on nonmodified Pt(1 1 1). It was also demonstrated that the mechanistic pathway for this reaction depends directly on the degree of osmium coverage. Thus, for low osmium coverage (θ_Os ≤ 0.28), the formation of CO as an intermediate is favored, and hence the full oxidation of adsorbed ethanol to CO₂ is increased, additionally, the formation of acetaldehyde is also observed in low degrees of osmium coverage. For intermediate osmium coverage (0.28 < θ_Os ≤ 0.40), the oxidation of ethanol to acetaldehyde and then to acetic acid is favored, although on Pt(1 1 1) the formation of acetaldehyde is promoted. For higher degrees of osmium coverage (θ_Os > 0.51), the catalytic activity of the electrode for ethanol oxidation decreases. For an almost complete osmium layer (θ_Os = 0.92), obtained by electrodeposition at 50 mV, catalytic activity for ethanol oxidation shows the lowest value. In addition, the direct oxidation of ethanol to acetic acid at lower potentials is observed.