Visible-light-induced photocatalytic activity of TiO2−xNy prepared by solvothermal process in urea–alcohol system

Nitrogen-doped anatase, rutile and brookite titania photocatalyst TiO_2−xN_y which can be excited by visible light were prepared by mixing aqueous TiCl₃ solutions with urea ((NH₂)₂CO) and various type of alcohols followed by solvothermal treatment at 190 °C. The phase composition, crystallinity, microstructure and specific surface area of titania powders greatly changed depending on the pH and type of solvents. Violet, yellowish and grayish TiO_2−xN_y with excellent visible light absorption and photocatalytic activity were prepared. The TiO_2−xN_y powders prepared in urea–methanol solution showed excellent photocatalytic ability for the oxidative destruction of nitrogen monoxide under irradiation of visible light λ > 510 nm.     

Effects of SiO2 addition on TiO2 crystal structure and photocatalytic activity

A series of TiO₂–SiO₂ mixtures – having the following stoichiometry Ti_1?xSi_xO₂, with x = 0, 0.1, 0.3 and 0.5 atoms per formula unit – were prepared by using precursor oxides and fired at three temperatures (900, 1000 and 1200 °C). The modifications in the structure and, consequently, on the photocatalytic activity, induced by the addition of SiO₂ into the TiO₂ powder, were thoroughly investigated by using various analytical techniques: X-ray powder diffraction, electron microscopy (FE-SEM and TEM), XPS, FT-IR, DRS and BET analysis. The results underlined as essentially no solid solution occurs between the two crystalline end-members. Nevertheless, silica addition caused a retarding effect on anatase-to-rutile phase transformation and on the crystallite growth.The photocatalytic activity of the powders was assessed in gas phase and the results were explained by taking into account the anatase and rutile relative amounts in the samples, their crystallite size, the surface hydroxyl groups adsorbed on the photocatalysts and the surface area of the mixtures.     

A novel TiO2 − xNx/BN composite photocatalyst: Synthesis,characterization and enhanced photocatalytic activity for Rhodamine B degradation under visible light

A novel TiO_2 − xN_x/BN composite photocatalyst was prepared via a facile method using melamine–boron acid adducts (M·2B) and tetrabutyl titanate as reactants. The morphological results confirmed that nitrogen-doped TiO₂ nanoparticles were uniformly coated on the surface of porous BN fibers. A red shift of absorption edge from 400 nm (pure TiO₂) to 520 nm (TiO_2 − xN_x/BN composites) was observed in their UV–Vis light absorption spectra. The TiO_2 − xN_x/BN photocatalysts exhibited enhanced photocatalytic activity for the degradation of Rhodamine B (RhB) and the highest photocatalytic degradation efficiency reached 97.8% under visible light irradiation for 40 min. The mechanism of enhanced photocatalytic activity was finally proposed.     

Enhanced photocatalytic degradation of rutile/anatase TiO2 heterojunction nanoflowers

Rutile/anatase TiO₂ heterojunction nanoflowers were prepared via a facile one-step hydrothermal approach using titanium tetrachloride and urea as the raw materials, cetyl trimethyl ammonium bromide (CTAB) as the template. The prepared TiO₂ nanoflowers were characterized by XRD, SEM, TEM and BET analyses. The photocatalytic performance of the as-prepared TiO₂ samples for methyl blue degradation under simulated solar light was investigated. TiO₂ heterojunction nanoflowers with mixed rutile/anatase phase (prepared with 3 mmol CTAB) give the highest photocatalytic activity. In addition, TiO₂ nanoflowers show excellent stability after 9 cycles under the same conditions. These results suggested that the mixed phase anatase/rutile TiO₂ heterojunction nanoflowers have great potential for the future photodegradation of real dye waste water.     

Suspension high velocity oxy-fuel spraying of a rutile TiO2 feedstock: Microstructure,phase evolution and photocatalytic behaviour

Nano-structured TiO₂ coatings were produced by suspension high velocity oxy fuel (SHVOF) thermal spraying using water-based suspensions containing 30 wt% of submicron rutile powders (~180 nm). By changing the flame heat powers from 40 kW to 101 kW, TiO₂ coatings were obtained with distinctive microstructures, phases and photocatalytic behaviour. Spraying with low power (40 kW) resulted in a more porous microstructure with the presence of un-melted nano-particles and a lower content of the anatase phase; meanwhile, high powers (72/101 kW) resulted in denser coatings and rougher surfaces with distinctive humps but not necessarily with a higher content of anatase. Linear sweep voltammetry (LSV) was used to evaluate the photocatalytic performance. Surprisingly, coatings with the lowest anatase content (~20%) using 40 kW showed the best photocatalytic behaviour with the highest photo-conversion efficiency. It was suggested that this was partially owing to the increased specific surface area of the un-melted nano-particles. More importantly, the structural arrangement of the similarly sized TiO₂ nano-crystallites between rutile and antase phases also created catalytic “hot spots” at the rutile−anatase interface and greatly improved the photo-activity.     

Decomposition of nonionic surfactant on a nitrogen-doped photocatalyst under visible-light irradiation

A visible-light-active N-containing TiO₂ photocatalysts were prepared from crude amorphous titanium dioxide by heating amorphous TiO₂ in gaseous NH₃ atmosphere. The calcination temperatures ranged from 200 to 1000 °C, respectively. UV–vis/DR spectra indicated that the N-doped catalysts prepared at temperatures <400 °C absorbed only UV light (E_g = 3.3 eV), whereas samples prepared at temperatures ≥400 °C absorbed both, UV (E_g = 3.10–3.31 eV) and vis (E_g = 2.54–2.66 eV) light. The chemical structure of the modified photocatalysts was investigated using FT-IR/DRS spectroscopy. All the spectra exhibited bands indicating nitrogen presence in the catalysts structure. The photocatalytic activity of the investigated catalysts was determined on a basis of a decomposition rate of nonionic surfactant (polyoxyethylenenonylphenol ether, Rokafenol N9). The most photoactive catalysts were those calcinated at 300, 500 and 600 °C. For the catalysts heated at temperatures of 500 and 600 °C Rokafenol N9 removal was equal to 61 and 60%, whereas TOC removal amounted to 40 and 35%, respectively. In case of the catalyst calcinated at 300 °C surfactant was degraded by 54% and TOC was removed by 35%. The phase composition of the most active photocatalysts was as follows: (a) catalyst calcinated at 300 °C—49.1% of amorphous TiO₂, 47.4% of anatase and 3.5% of rutile; (b) catalyst calcinated at 500 °C—7.1% of amorphous TiO₂, 89.4% of anatase and 3.5% of rutile; (c) catalyst calcinated at 600 °C—94.2% of anatase and 5.8% of rutile.     

Enhanced photocatalytic activity of electrospun TiO2/ZnO nanofibers with optimal anatase/rutile ratio

The photocatalytic characteristics of the TiO₂/ZnO nanofibers synthesized by electrospinning followed by calcinating at different temperatures to alter the anatase-to-rutile ratio are investigated. The results demonstrate that the photocatalytic activity of TiO₂/ZnO nanofibers is enhanced by optimizing the anatase/rutile ratio among the trade-off effects of the band-gap energy, the electron/hole recombination rate, and the surface area. When calcined at 650 °C, the TiO₂/ZnO nanofibers with optimal anatase/rutile ratio (48:52) balancing these trade-off effects have the highest photocatalytic efficiency both in the degradation of RhB in liquid and conversion of NO gas.     

TiO2 nanofibers doped with rare earth elements and their photocatalytic activity

In the present study rare earth doped (Ln³⁺–TiO₂, Ln = La, Ce and Nd) TiO₂ nanofibers were prepared by the sol–gel electrospinning method and characterized by XRD, SEM, EDX, TEM, and UV-DRS. The photocatalytic activity of the samples was evaluated by Rhodamine 6G (R6G) dye degradation under UV light irradiation. XRD analysis showed that all the synthesized pure and doped titania nanofibers contain pure anatase phase at 500 °C but at 700 °C it shows both anatase and rutile phase. XRD result also shows that Ln³⁺-doped titania probably inhibits the phase transformation. The diameter of nanofibers for all samples ranges from 200 to 700 nm. It was also observed that the presence of rare-earth oxides in the host TiO₂ could decrease the band gap and accelerate the separation of photogenerated electron–hole pairs, which eventually led to higher photocatalytic activity. To sum up, our study demonstrates that Ln³⁺-doped TiO₂ samples exhibit higher photocatalytic activity than pure TiO₂ whereas Nd³⁺-doped TiO₂ catalyst showed the highest photocatalytic activity among the rare earth doped samples.     

Fabrication of nitrogen-doped TiO2 monolith with well-defined macroporous and bicrystalline framework and its photocatalytic performance under visible light

In this study, hierarchically porous bicrystalline nitrogen-doped titania (N-doped TiO₂) monolithic material was fabricated by a simple two-step approach: (i) preparation of TiO₂ porous monolith by a sol–gel process of titanium alkoxide in a mild condition utilizing a chelating agent and mineral salt and (ii) annealing of TiO₂ porous monolith obtained under a modest flow of ammonia gas at 700 °C for 2 h. The phase composition, crystal structure, morphology, pore structure, and porous properties of the final product were studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), mercury porosimetry, and nitrogen physisorption measurement, respectively. The resultant N-doped TiO₂ porous monolith possesses a bicrystalline (anatase and rutile) framework with a well-defined macroporosity. The results from X-ray photoelectron spectroscopy (XPS) confirm the formation of OTiN bonds in the N-doped TiO₂ porous monolith. The photocatalytic activity of N-doped TiO₂ porous monolith was evaluated by the photodegradation of Rhodamine B over the samples under visible light. Nearly 50% of Rhodamine B in aqueous solution was efficiently degraded by N-doped TiO₂ porous monolith with the mixed-phase of anatase and rutile under visible light within 120 min.     

Synergic effect of cation doping and phase composition on the photocatalytic performance of TiO2 under visible light

The synergic effect of cation doping and phase composition for the further improvement of the photocatalytic activity of TiO₂ under visible light is reported for the first time. Fe^3 + and Sn^4 + co-doped TiO₂ with optimized phase composition were synthesized through a simple soft-chemical solution method. The visible-light-driven photocatalytic activity of Fe^3 + and Sn^4 + co-doped TiO₂ was 5 times of that of Evonik P25 TiO₂ using degradation of methylene blue as model reaction. The synthesized photocatalysts were characterized by powder X-ray diffraction, UV–Vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, ¹¹⁹Sn Mössbauer spectroscopy, and X-ray absorption fine structure spectroscopy. It is indicated that Sn^4 + doping can facilitate the phase transition from anatase to rutile. The different ratios of anatase and rutile can be achieved by tuning the amount of Sn^4 + doped into the lattice. Furthermore, the doping of Sn^4 + into TiO₂ lattice can stabilize the phase composition when Fe^3 + is co-doped. In the Fe^3 + and Sn^4 + co-doped TiO₂, Sn^4 + is mainly used to tune and stabilize the phase composition of TiO₂ and Fe^3 + acts as a doping cation to narrow the band gap of TiO₂. Both band gap and phase composition of TiO₂ can be tuned effectively by the simultaneous introduction of Fe^3 + and Sn^4 +. The synergic effect of optimized phase composition (anatase/rutile = 25/75) and narrowed band gap should be the two main reasons for the promoted photocatalytic activity of TiO₂ under visible light.     

Photocatalytic Nb2O5-doped TiO2 nanoparticles for glazed ceramic tiles

TiO₂ nanoparticles are currently used as coating for self-cleaning building products. In order to achieve high self-cleaning efficiency for outdoor applications, it is important that titania is present as anatase phase. Moreover, it is desirable that the particle sizes are in nano-range, so that a large enough surface area is available for enhanced catalytic performance. In this work, TiO₂ nanoparticles doped with 0–5 mol% Nb₂O₅ were synthesized by co-precipitation. Nb₂O₅ postponed the anatase to rutile transformation of TiO₂ by about 200 °C, such that after calcination at 700 °C, no rutile was detected for 5 mol% Nb₂O₅-doped TiO₂, while undoped TiO₂ presented 90 wt% of the rutile phase. A systematic decreasing on crystallite size and increasing on specific surface area of TiO₂ were observed with higher concentration of Nb₂O₅ dopant. Photocatalytic activity of anatase polymorph was measured by the decomposition rate of methylene blue under ultraviolet and daylight illumination and compared to commercial standard catalyst (P25). The results showed enhanced catalysis under UV and visible light for Nb₂O₅-doped TiO₂ as compared to pure TiO₂. In addition, 5 mol% Nb₂O₅-doped TiO₂ presented higher photocatalytic activity than P25 under visible light. The enhanced performance was attributed to surface chemistry change associated with a slight shift in the band gap.     

HIPed TiO2 dense pellets with improved photocatalytic performance

The effects of heating method and temperature on physical, structural and photocatalytic behaviors of TiO₂ pellets prepared by conventional heating and hot isostatic pressing have been evaluated. The pellets of submicron TiO₂ powders were heated to 600, 650, 700, 750 and 1000 °C using both processing methods in order to compare anatase to rutile phase transformation and densification behaviors. Bulk densities and porosities were calculated using the Archimedes method. XRD analysis were performed to calculate anatase/rutile ratios. Microstructures were characterized using SEM. Photocatalytic experiments have been performed under full spectrum irradiation. Degraded methylene blue samples were periodically monitored through UV–vis spectrophotometer to determine degradation kinetics. Anatase to rutile transformation is slightly faster and densification is better for lower temperatures for conventional heating, however HIPing gives better densification above 750 °C as it also retards rutile transformation. Mixed phase structures and HIPed samples showed the best photocatalytic performance which makes this method advantageous.     

Kinetics of anatase transition to rutile TiO2 from titanium dioxide precursor powders synthesized by a sol-gel process

Kinetics of anatase transition to rutile TiO₂ from titanium dioxide precursor powders synthesized by a sol-gel process have been studied using differential thermal analysis (DTA), X-ray diffraction, transmission electron microscopy (TEM), selected area electron diffraction (SAED), nano beam electron diffraction (NBED) and high resolution TEM (HRTEM). The DTA result shows residual organic matter decomposed at 436 K. The transition temperature for amorphous precursor powders converted to anatase TiO₂ occurred at 739 K. Moreover, the full anatase transition to rutile TiO₂ occurred at 1001 K. The activation energy of anatase TiO₂ formation was 128.9 kJ/mol. On the other hand, the activation energy of anatase transition to rutile TiO₂ was 328.4 kJ/mol. Mesoporous structures can be observed in the TEM image.     

Ordered mesoporous carbon–TiO2 materials for improved electrochemical performance of lithium ion battery

A series of ordered mesoporous carbon–TiO₂ (OMCT) materials with various weight percentages of TiO₂ (50–75 wt%) were synthesized by evaporation-induced self-assembly and in-situ crystallization at various calcination temperatures (600–1200 °C) to evaluate the Li-ion storage performance. The OMCT has ordered 2D hexagonal mesoporous structures and the TiO₂ nanocrystals with different phases are embedded into the frameworks of carbonaceous matrix. The reversible capacity of OMCT is highly dependent on the phase and content of TiO₂, and the anatase TiO₂ is a superior crystalline phase to rutile and TiN for Li-ion insertion. The OMCT₆₅ which contains 35 wt% carbon and 65 wt% TiO₂ shows a high capacity of 500 mAh g^?1 at 0.1C after 80 cycles. In addition, OMCT₆₅ exhibits a good cyclability and rate capability. The reversible capacity remains at 98 mAh g^?1 at a high rate of 5C, and then recoveries to 520 mAh g^?1 at 0.1C after 105 cycles. The excellent reversible capacity and rate capability of OMCT₆₅ are attributed to the embedment of well-dispersed anatase TiO₂ nanocrystals into the specific porous structure of OMCT, which can not only facilitate the fast Li-ion charge transport but can also strengthen the carbon–TiO₂ co-constructing channels for lithiated reactions.     

Photocatalytic activity of rubber sheet impregnated with TiO2 particles and its recyclability

The preparation of rubber sheet impregnated with titanium dioxide particles is presented. This method is simple and low cost based on the use of commercial TiO₂ powder directly mixing with rubber latex (60% HA) and distilled water. The morphology and roughness of the sheet surface increased with increasing amount of distilled water. Sheet impregnated with anatase (Imp-An) showed uniform, small grains with dense structure and well surface coverage more than one with P25 (Imp-P25). Their photocatalytic activities were evaluated using methylene blue (MB) as a model organic dye compound. These impregnated sheets could degrade MB solution under UV-light irradiation. Comparing with the commercial TiO₂ samples in powder form (anatase from Carlo Erba and Degussa P25) the efficiencies of photocatalytic degradation of MB fall in the decreasing order as: P25 (powder) > anatase (Carlo Erba) (powder) > Imp-An sheet > Imp-P25 sheet. However, the impregnated sheet has an advantage over the loose powder that the catalyst sheet can be recovered after used and can be reused.     

Improved radiation damage tolerance of titanium nitride ceramics by introduction of vacancy defects

TiN and TiN_0.7 were irradiated using a 100 keV Ar-ion beam at 600 °C to target doses of 3 × 10¹⁷ ions cm⁻². SRIM estimation, GIXRD and fluorescence analysis have been performed to evaluate the effect of pre-existing vacancy defect on the radiation tolerance. The lattice parameter of TiN increased after irradiation due to interstitial atoms and vacancies in as-irradiated TiN. In contrary, the lattice parameter decreased for as-irradiated TiN_0.7, which indicates that the nitrogen atom vacancies in TiN_0.7 acted as sinks for displacement atoms generated by irradiation to limit interstitial atoms existing. The intensity of peaks in fluorescence spectrum of as-irradiated TiN was higher than that of as-irradiated TiN_0.7. That attributed to the presence of color centers formed by Frenkel defects in as-irradiated TiN. All of the results indicate that introducing vacancy defect in materials would offer capability to realize self-heal of irradiation damage.     

Palygorskite and SnO2–TiO2 for the photodegradation of phenol

The photocatalytic removal of phenol was studied using palygorskite-SnO₂–TiO₂ composites (abbreviated as Paly-SnO₂–TiO₂) under ultraviolet radiation. The photocatalysts were prepared by attachment of SnO₂–TiO₂ oxides onto the surface of the palygorskite by in situ sol–gel technique. The products were characterized by XRD, TEM and BET measurements. SnO₂–TiO₂ nanoparticles, with an average diameter of about 10 nm, covered the surface of the palygorskite fibers without obvious aggregation. Compared with palygorskite-titania (Paly-TiO₂), palygorskite-tin dioxide (Paly-SnO₂), and Degussa P25, Paly-SnO₂–TiO₂ and SnO₂–TiO₂ exhibited much higher photocatalytic activity. The photodecomposition of phenol was as high as 99.8% within 1.5 h. The apparent rate constants (k_app) for Paly-SnO₂–TiO_2, TiO₂, and P25 were measured. Paly-SnO₂–TiO₂ showed the highest rate constant (0.03435 min^?1). The chemical oxygen demand (COD) of the phenol solution was reduced from 220.2 mg/L to 0.21 mg/L, indicating the almost complete decomposition of phenol. Reusability of the photocatalyst was proved.     

Photocatalytic activity of titanium dioxide coatings: Influence of the firing temperature of the chemical gel

Heterogeneous photocatalysis can be exploited for the decomposition of micro-organisms which have developed on the surfaces of building materials. In this work, the efficiency of titanium dioxide coatings on fired clay products is examined. The sol–gel method is used to synthesize a fine TiO₂ powder with a specific surface area of 180 m² g^?1. Thermal treatment of the chemical gel at 340 °C leads to crystallisation in the anatase phase and with further temperature increase, crystallite growth. For thermal treatments in the range 580–800 °C, there is a progressive transition from anatase to rutile. However, despite a decrease in specific surface area of the powder attributed to aggregation/agglomeration, the coherent domain size deduced from X-ray diffraction measurements remains almost constant at 23 nm. Once the transition is completed, increase of thermal treatment temperature above 800 °C leads to further crystallite growth in the rutile phase. The thermally treated titania powders were then sprayed onto fired clay substrates and the photocatalytic activity was assessed by the aptitude of the coating to degrade methylene blue when exposed to ultraviolet light. These tests revealed that the crystallite size is the important controlling factor for photocatalytic activity rather than the powder specific surface area or the anatase/rutile polymorph ratio.     

Synthesis of phase- and shape-controlled TiO2 nanoparticles via hydrothermal process

The TiO₂ nanoparticles with anatase (5.7–12.7 nm), rutile (5.4–8.8 nm), mixed (4.4–8.6 nm) phase were individually prepared using the hydrothermal method. The structure and shape of the particles could be controlled by careful alterations of the hydrothermal conditions. Herein, the TiO₂ nanoparticles were successfully synthesized by employing Ti-isopropoxide as the titanium source into hydrochloric acid solution at mild conditions. The crystal structures such as anatase, rutile and mixed phase of TiO₂ nanoparticles were determined by means of concentration of hydrochloride. Especially, we observed that the rutile TiO₂ crystallites were grown into one-dimensional nanostructures, especially, nanowires, with increasing reaction time. The mechanism of the crystallization of the nanoparticles and the growth habit of TiO₂-rutile structure were discussed.     

Characteristics and catalytic properties of Co/TiO2 for various rutile:anatase ratios

This present study revealed a dependence of rutile:anatase ratios in titania on the characteristics and catalytic properties of Co/TiO₂ catalysts during CO hydrogenation. In this study, Co/TiO₂ catalysts were prepared using various titania supports consisting of various rutile:anatase ratios of titania. In order to identify the characteristics, all catalyst materials were characterized using XRD, SEM/EDX, TPR, and hydrogen chemisorption. CO hydrogenation (H₂/CO = 10/1) was also performed to determine the overall activity and selectivity. It was found that both activity and selectivity were altered by changing the rutile:anatase ratios in the titania support.