Electrochemical surface plasmon resonance detection of enzymatic reaction in bilayer lipid membranes

In this paper, electrochemical surface plasmon resonance (SPR) method was first used to detect enzymatic reaction in bilayer lipid membrane (BLM) based on immobilizing horseradish peroxidase (HRP) in the BLMs supported by the redox polyaniline (PAn) film. By SPR kinetic curve in situ monitoring the redox transformation of PAn film resulted from the reaction between HRP and PAn, the enzymatic reaction of HRP with H(2)O(2) was successfully analyzed by electrochemical SPR spectroscopy. The results show that this BLM supported on PAn film cannot only preserve the bioactivity of HRP immobilized in the membrane, but also provide a channel for the transfer of electrons between HRP and PAn on electrode surface. These characteristics enabled the development of SPR biosensor for sensitively detecting H(2)O(2). H(2)O(2) has been detected by electrochemical SPR spectroscopy in the concentration range of 5 x 10(-5)M to 2 x 10(-3)M. After each of detections, the SPR sensor surface was completely regenerated by electrochemically reducing the oxidized PAn to its reduced state. This method provides a novel route for enhancing the detection of small ligand of enzymatic reaction in BLM by electrochemical SPR spectroscopy.     

A novel electrochemical SPR biosensor

In this paper, we demonstrate for the first time that upon electrochemical oxidation/reduction, the transition in the conductivity of polyaniline (PAn) film on gold electrode surface leads to a large change of surface plasmon resonance (SPR) response due to a change in the imaginary part of dielectric constant of PAn film. Based on the amplifying response of SPR to the redox transformation of PAn film as a direct result of the enzymatic reaction between horseradish peroxidase (HRP) and PAn in the presence of H₂O₂, a novel PAn-mediated HRP sensor has been fabricated. The electrochemical SPR biosensor, unlike a usual binding assay with SPR, can afford a larger SPR response, and can also be reused by reducing the PAn film electrochemically to its reduced state. This method opens up a new route to the fabrication of SPR biosensor.     

Nanoelectrode ensembles based on conductive polyaniline/poly(acrylic acid) using porous sol–gel films as template

Porous sol–gel (PSG) film has been utilized as a template for the electrochemical polymerization of aniline in presence of poly(acrylic acid) (PAA). The presence of electroactive polyaniline (PAn)/PAA within the porous skeleton of the sol–gel films has been confirmed using cyclic voltammetry, UV–vis spectrometry and atomic force microscopic measurements. The densities and the sizes of the nanoelectrodes can be controlled easily using electrochemical methods. The conductive polymer “wires” of PAn/PAA formation in PSG matrix can behave as an ensemble of closely-spaced but isolated nanoelectrodes. Moreover, the nanoelectrode ensembles based on conductive PAn/PAA for glucose biosensing are fabricated by immobilization of glucose oxidase (GOx) and Nafion onto the surface of conductive polymer. Owing to the biocompatibility of PSG and electro-activity of PAn/PAA at neutral pH regions, the glucose biosensor shows excellent characteristics and performance, such as low detection limit and fast response time.     

聚苯胺薄膜修饰电极对抗坏血酸的电催化氧化

本文表明聚苯胺(PAn)薄膜修饰电极对水溶液中的抗坏血酸(AH_2)在较宽的pH范围和较宽的浓度范围内均有良好的电催化氧化作用, 为EC平行催化过程。利用旋转圆盘电极(RDE)进行了催化过程动力学分析, 求出了催化反应动力学参数。在抗坏血酸浓度10~(-2)～10~(-6) mol·L~(-1)范围内, 催化峰电流与AH_2浓度均成良好的线性关系, 且PAn薄膜修饰电极具有很好的稳定性, 有应用分析抗坏血酸的意义。     

Effects of polyaniline chain structures on proton conduction in a PEM host matrix

This study examined the effects of the conjugated chain structure of polyaniline (PAn) on proton transport in a proton exchange membrane (PEM) containing a small amount of PAn colloidal particles. The PEM host matrix consisted of a hydrophobic three-component polymer blend (TCPB) of poly(4-vinylphenol-co-methylmethacrylate) P(4-VP-MMA), poly(butyl methacrylate) (PBMA), and Paraloid^® B-82 acrylic copolymer resins; in which a hydrophilic network of 2-acrylamido-2-methyl propanesulfonic acid (AMPS), 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol)dimethylacrylate (PEGDMA) was formed upon embedded polymerization. Colloidal PAn particles were added to the PEM matrix during the embedded polymerization of PEM. Two types of PAn colloidal particles with different chain structures and morphologies were synthesized by inverse miniemulsion polymerization and interfacial polymerization. The PAn(1) particles from inverse miniemulsion polymerization were bar-shaped, contained a higher fraction of quinoid diimine units than the scaffold-like PAn(2) particles from interfacial polymerization, and displayed a strong promotional effect on proton conduction. The oxidation state of the PAn particles was also varied by post-synthesis treatments to evaluate the effect of oxidation state on proton conduction. It was found that a mixed oxidation state such as the emeraldine form of PAn had the best enhancement effect. The PAn loading optimal for proton conductivity enhancement of the composite PEM was determined to be about 2 wt% of PAn(1).     

Enhanced Bioelectrocatalysis Using Single‐Walled Carbon Nanotubes (SWCNTs)/Polyaniline Hybrid Systems in Thin‐Film and Microrod Structures Associated with Electrodes

The charge transport properties in composites consisting of pyrene sulfonic acid‐functionalized single‐walled carbon nanotubes embedded in polyaniline, PAn/SWCNTs, and polystyrene sulfonate‐doped PAn, PAn/PSS, are compared in thin‐film and microrods configurations. The PAn/SWCNTs and PAn/PSS microrods were prepared by the electropolymerization of the respective components in porous alumina membranes coated with a conductive gold support, followed by the dissolution of the membrane template. The charge transport upon the oxidation of the PAn/SWCNTs planar film or microrods structures is ca. 3.5–4.0‐fold faster than upon the oxidation of the PAn/PSS planar film or microrods structures, respectively. The faster charge transport in the PAn/SWCNTs films and microrods is used to enhance the mediated bioelectrocatalyzed oxidation of glucose in the presence of glucose oxidase (GOx). The bioelectrocatalyzed oxidation of glucose in the presence of the PAn/SWCNTs in the planar film and microrods structures is ca. 2‐fold and up to 6‐fold (depending on the potential) enhanced as compared to the respective PAn/PSS configurations.     

Polymer-metal complexes in polyelectrolyte multilayer films as catalysts for oxidation of toluene

We report on the binding of metal ions (Me(2+); Co(2+) and Cu(2+)) with weak polyelectrolyte multilayers (PEMs), as well as on catalytic activity of PEM-Me(2+) films for oxidation of toluene. Using several types of PEM films constructed using branched polyethyleneimine (BPEI) or quaterinized poly-4-vinylpyridines (QPVPs) as polycations and poly(acrylic acid) (PAA) or poly(styrene sulfonate) (PSS) as polyanions, we found that binding of Co(2+) and Cu(2+) ions with a PEM matrix can occur both through coordination to polycationic amino groups and/or ionic binding to polyacid groups. The amount of metal ions loaded within the film increased linearly with film thickness and was strongly dependent on polyelectrolyte type, film assembly pH, and fraction of permanent charge in polymer chains. Among various PEM-Me(2+) systems, BPEI/PAA-Co(2+) films assembled at pH 8.5 show the best catalytic performance, probably because of the preservation of high mobility of Co(2+) ions coordinated to amino groups of BPEI in these films. With BPEI/PAA-Co(2+) films, we demonstrated that films were highly permeable to reagents and reaction products within hundreds of nanometers of the film bulk; i.e., film catalytic activity increased linearly with layer number up to 30 bilayers and slowed for thicker films.     

过氧化氢在磺酸二茂铁掺杂的聚苯胺上的电催化氧化

在含有磺酸二茂铁溶液中合成的聚苯胺（PAnFc）和不含磺酸二茂铁溶液中合成的聚苯胺（PAn）,在pH 5.0的缓冲溶液中均能催化过氧化氢的氧化,但PAnFc的催化活性高于PAn.催化效应的证据是过氧化氢在裸铂电极上的氧化电位为0.59 V(vs SCE),而在PAnFc电极仅是0.48 V,以及过氧化氢在PAnFc电极上的阳极峰电流是裸铂电极上的5.3倍.根据这种催化特性,用PAn和PAnFc固定葡萄糖氧化酶形成酶电极.实验结果表明,PAnFc酶电极的响应电流比PAn酶电极高得多,而且响应快.这是由于PAnFc在pH 5.0缓冲液中的电化学活性高于PAn,以及掺杂在聚苯胺中的磺酸二茂铁起着重要的电荷传递作用.     

An amperometric biosensor for glucose based on electrodeposited redox polymer/glucose oxidase film on a gold electrode.

In this paper, we described a glucose biosensor based on the co-electrodeposition of a poly(vinylimidazole) complex of [Os(bpy)2Cl](+/2+) (PVI-Os) and glucose oxidase (GOX) on a gold electrode surface. The one-step co-electrodeposition method provided a better control on the sensor construction, especially when it was applied to microsensor construction. The modified electrode exhibited the classical features of a kinetically fast redox couple bound to an electrode surface and the redox potential of the redox polymer/enzyme film was 0.14 V (vs. SCE). For a scan rate of up to 200 mV s(-1), the peak-to-peak potential separation was less than 25 mV. In the presence of glucose, a typical catalytic oxidation current was observed, which reached a plateau at 0.25 V (vs. SCE). Under the optimal experimental conditions, the steady-state electrooxidation current measured at 0.30 V (vs. SCE) was linear to the glucose concentration in the range of 0-30 mM. Successful attempts were made in blood sample analysis.     

Magneto-switchable electrocatalytic and bioelectrocatalytic transformations

Magnetic switching of redox reactions and bioelectrocatalytic transformations is accomplished in the presence of relay-functionalized magnetite particles (Fe(3)O(4)). The electrochemistry of a naphthoquinone (1), pyrroloquinoline quinone (2; PQQ), microperoxidase-11 (3), a ferrocene derivative (4) and a bipyridinium derivative (5), functionalized magnetic particles, is switched "ON" and "OFF" by an external magnet upon the attraction of the magnetic particles to an electrode or their retraction from the electrode, respectively. The magneto-switchable activation and deactivation of the electrochemical oxidation of the ferrocene-functionalized magnetic particles and the electrochemical reduction of the bipyridinium-functionalized magnetic particles are used for the triggering of mediated bioelectrocatalytic oxidation of glucose, in the presence of glucose oxidase (GOx), and bioelectrocatalytic reduction of nitrate (NO(3) (-)), in the presence of nitrate reductase (NR), respectively. Magnetic particles functionalized with a PQQ-NAD(+) dyad are used for the magnetic switching of the bioelectrocatalytic oxidation of lactate in the presence of lactate dehydrogenase (LDH). The coupling of these particles with a ferrocene-monolayer-functionalized electrode allows the dual and selective sensing of lactate and glucose in the presence of LDH and GOx, respectively, by using an external magnet to switch the detection mode.     

Efficient Artificial Electron Acceptors for Monoamino Oxidase in Bioelectrooxidation of Monoamines: Phenothiazine Dyes

Catalytic properties of monoamino oxidase (MAO) in a homogeneous reaction of oxidation and a heterogeneous reaction of bioelectrocatalytic oxidation of benzylamine by derivatives of phenothiazine and phenoxazine (artificial electron acceptors) is studied. The efficiency of electroenzymic catalysis involving Methylene Blue and MAO immobilized on the electrode is comparable to that of homogeneous enzymic catalysis. When immobilized in a film of polymer electrolyte Eastman AQ-29, Methylene Blue and Toluidine Blue efficiently carry electrons from the reduced redox center of immobilized MAO onto a glassy-carbon electrode. Dependence of the oxidation current of these compounds on the concentration of the benzylamine substrate is studied and it is shown that the enzymic reaction is the limiting stage in a bioelectrocatalytic process. This conclusion gives grounds for using the dependence of the anodic current on the monoamine concentration as a calibration plot when assaying biogenic amines.     

Characteristics of a surface plasmon resonance sensor combined with a poly(vinyl chloride) film-based ionophore technique for metal ion analyses.

The characteristics of a surface plasmon resonance (SPR) sensor prepared by coating a metal film evaporated on a prism with a polymer film containing tetra-n-butyl thiuram disulfide (TBTDS) were studied. The differences in the sensitivity, selectivity, and detection limit for a Zn2+ ion of the SPR sensor were reported as a function of the thickness of the polymer film, the kind of a metal film, and the kind of a polymer film. The thinner was the polymer film, the higher was the sensitivity, and the lower was the detection limit. The Ag film gave to the SPR sensor higher sensitivity than the Au film. TBTDS contained in the poly(vinyl chloride) (PVC) film slightly improved the selectivity toward the Zn2+ ion. A non-conditioned poly(methyl methacrylate) (PMMA) film containing TBTDS gave a lower detection limit of 1.0 x 10(-6) mol/l, which is similar to that obtained by using an ion selective electrode (ISE) method, than the PVC film. The PVC film, however, gave higher concentration resolution than the PMMA film.     

Electrical contacting of glucose dehydrogenase by the reconstitution of a pyrroloquinoline quinone-functionalized polyaniline film associated with an Au-electrode: an in situ electrochemical SPR study

A novel method to generate an integrated electrically contacted glucose dehydrogenase electrode by the surface reconstitution of the apo-enzyme on a pyrroloquinoline quinone (PQQ)-modified polyaniline is described. In situ electrochemical surface plasmon resonance (SPR) is used to characterize the bioelectrocatalytic functions of the system.     

A biofuel cell with electrochemically switchable and tunable power output

An electroswitchable and tunable biofuel cell based on the biocatalyzed oxidation of glucose is described. The anode consists of a Cu(2+)-poly(acrylic acid) film on which the redox-relay pyrroloquinoline quinone (PQQ) and the flavin adenine dinucleotide (FAD) cofactor are covalently linked. Apo-glucose oxidase is reconstituted on the FAD sites to yield the glucose oxidase (GOx)-functionalized electrode. The cathode consists of a Cu(2+)-poly(acrylic acid) film that provides the functional interface for the covalent linkage of cytochrome c (Cyt c) that is further linked to cytochrome oxidase (COx). Electrochemical reduction of the Cu(2+)-poly(acrylic acid) films (applied potential -0.5 V vs SCE) associated with the anode and cathode yields the conductive Cu(0)-poly(acrylic acid) matrixes that electrically contact the GOx-electrode and the COx/Cyt c-electrode, respectively. The short-circuit current and open-circuit voltage of the biofuel cell correspond to 105 microA (current density ca. 550 microA cm(-2)) and 120 mV, respectively, and the maximum extracted power from the cell is 4.3 microW at an external loading resistance of 1 kOmega. The electrochemical oxidation of the polymer films associated with the electrodes (applied potential 0.5 V) yields the nonconductive Cu(2+)-poly(acrylic acid) films that completely block the biofuel cell operation. By the cyclic electrochemical reduction and oxidation of the polymer films associated with the anode and cathode between the Cu(0)-poly(acrylic acid) and Cu(2+)-poly(acrylic acid) states, the biofuel cell performance is reversibly switched between "ON" and "OFF" states, respectively. The electrochemical reduction of the Cu(2+)-polymer film to the Cu(0)-polymer film is a slow process (ca. 1000 s) because the formation and aggregation of the Cu(0)-clusters requires the migration of Cu(2+) ions in the polymer film and their reduction at conductive sites. The slow reduction of the Cu(2+)-polymer films allows for the controlling of the content of conductive domains in the films and the tuning of the output power of the biofuel cell. The electron-transfer resistances of the cathodic and anodic processes were characterized by impedance spectroscopy. Also, the overall resistances of the biofuel cell generated by the time-dependent electrochemical reduction process were followed by impedance spectroscopy and correlated with the internal resistances of the cell upon its operation.     

Photocurrent amplification by an energy/electron transfer cascade in polymer Langmuir-Blodgett films

Effective photocurrent generation by visible light irradiation on hetero-deposited polymer Langmuir-Blodgett (LB) films containing tris(bipyridine) ruthenium(II) (Ru(bpy)3(2+)) and anthracene derivatives was observed. The photocurrent amplification was found to be assisted by the photoinduced energy/electron transfer cascade, which consists of the interlayer triplet-triplet energy transfer process from photoexcited Ru(bpy)3(2+) to anthracene, and then electron transfer processes from the triplet anthracene to a viologen acceptor, from Ru(bpy)3(2+) to the oxidized anthracene and from the electrode to Ru(bpy)3(3+).     

导电高聚物修饰纳米尺度TiO~2多孔膜电极的光电化学研究

用光电化学方法研究了用导电高聚物修饰的纳米晶TiO~2多孔膜电极在不含氧化还原对和含不同氧化还原对体系电解质溶液中的光电转换过程。TiO~2/导电高聚物多孔膜电极为双层n型半导体结构,内层TiO~2多孔膜的禁带宽度为3.26eV,外层聚吡咯(PPy)膜的禁带宽度为2.23eV,而聚苯胺(PAn)膜的禁带宽度为2.88eV。用导电高聚物修饰半导体电极能使其在可见光区的光吸收增加,光电流增强,且起始波长红移至>600nm,使宽禁带半导体电极的光电转换效率得到明显改善。     

聚苯胺/顺丁橡胶复合导电膜的制备与性能(Ⅱ)

采用再掺杂方法制得了樟脑磺酸掺杂的聚苯胺(PAn-CSA),用溶液共混法制备PAn／BR导电复合膜．研究了聚苯胺与顺丁橡胶(BR)复合膜在间甲酚二次掺杂前后电导率的变化。实验表明:CSA对聚苯胺有较好的掺杂作用;二次掺杂使PAn复合膜电导率明显提高,其导电渗滤阈值略有降低,使卷曲的二次掺杂PAn链展开并通过分子链间的相互作用而自行组成导电通路．     

聚苯胺水基胶体分散液及其复合物的研究 Ⅰ制备、表征及复合物的表观形貌、力学性能

以聚乙烯醇（ＰＶＡ）为稳定剂（ｓｔｅｒｉｃｓｔａｂｉｌｉｚｅｒ）利用分散聚合（ｄｉｓｐｅｒｓｉｏｎｐｏｌｙｍｅｒｉ ｚａｔｉｏｎ）的原理，成功地制备出了稳定的聚苯胺（ＰＡｎ）水基胶体分散液．聚苯胺颗粒的大小受聚合条件如稳定剂浓度、单体浓度、温度以及搅伴状态等的影响．ＰＶＡ通过物理作用吸附在ＰＡｎ颗粒的表面，起到阻止ＰＡｎ颗粒进一步团聚的作用．但这种作用力较弱．ＰＡｎ颗粒的原始尺寸大小约为２０ｎｍ．由此原始颗粒组成了尺寸在１００ｍｍ～２００ｍｍ左右的稳定颗粒     

Sol-gel based amperometric biosensor incorporating an osmium redox polymer as mediator for detection of L-lactate

A novel amperometric biosensor for the determination of lactate was constructed by first immobilizing lactate oxidase and an osmium redox polymer ([Os(bpy)(2)(PVP)(10)Cl]Cl; abbreviated Os-polymer) on the surface of a glassy carbon electrode, followed by coating with a sol-gel film derived from methyltriethoxysilane (MTEOS). The electrooxidation current of this electrode was found to be diffusion controlled. In the presence of lactate, a clear electrocatalytic oxidation wave was observed, and lactate could be determined amperometrically at 400 mV versus Ag AgCl . The concentration range of linear response, slope of linear response and detection limit were 0.1-9 mM, 1.02 microA mM(-1), and 0.05 mM, respectively. Although L-ascorbate was electrooxidized at this potential, uric acid, paracetamol and glucose were found not to interfere.     

Multifunctional Mediating System Composed of a Conducting Polymer Matrix,Redox Mediator and Functionalized Carbon Nanotubes: Integration with an Enzyme for Effective Bioelectrocatalytic Oxidation of Glucose

A multifunctional mediating system for bioelectrocatalytic oxidation of glucose is described. It comprises a conducting polymer, poly(3,4‐ethylenodioxythiophene), carbon nanotubes modified with 4‐(pyrrole‐1‐yl) benzoic acid that provide carboxyl groups that aid immobilization of glucose oxidase in a conductive three‐dimensional network, tetrathiafulvalene that mediates electron exchange with the enzyme. This composite produces a system that is capable of effective oxidation of glucose to gluconic acid at pH 7. The current is concentration dependent to at least 60 mM and maintains 77 % of initial response for 35 days. Data supporting the utility of this system for electrochemical sensing and biofuel cell technology are presented.