共查询到20条相似文献,搜索用时 109 毫秒
1.
2.
3.
一种铝合金换热器真空钎焊新工艺最近在航空航天部六○九所试验成功,并通过了部级鉴定。 该项工艺采用微机多点测温、控温技术和分区加热对旧式真空钎焊炉进行技术改造,实现控温自动化,提高了控温精度(±1℃)和炉温的均匀性(温差小于3℃);并通过一系列工艺试验,得出了合理的钎焊过程热循环曲线、焊接工艺参数和最佳的加镁量等,同时设计了适用的焊接夹具。从而使铝合金钎焊技术达到了工程化应用要求,成功实现了铝合金换热器芯体的钎焊。该项技术提高了产品的质量和使用寿命,使合金换热器钎焊技术上了一个新台阶,并且首次用于国产飞机换热器生产。 相似文献
4.
5.
6.
本成果采用多层大面积弹性薄片组件氢气保护局部钎焊技术 ,成功地解决了飞行试验用的JZ7减振器中弹性组件钎焊的技术关键 ,工艺难度较大 ,属先进水平。同时解决了焊接方法、焊料研制、焊接设备、工艺等一系列问题 ,及时配合完成了JZ7减振器的研制任务。本成果在航天产品中有推广应用价值 ,在民品生产中也获得推广应用。解决了多层弹性叠片组件钎焊的技术难题。多层弹性叠片氢气保护钎焊@李连清 相似文献
7.
8.
通过对航天、航空飞行器管路系统常用材料(铝合金和不锈钢)的薄壁、小直径异材管路结构高频感应钎焊工艺试验研究,重点叙述了试验工艺、分析了影响接头质量的主要因素,并观察分析了接头微观组织和元素分布情况.结果表明:采用本试验研究中确认的合理工艺参数(钎料为AI-Si、钎剂为自制铝钎剂、装配间隙为0.04~0.1 mm、搭接长度为3 mm、钎焊电流为220 A、钎焊时间为30~33 s)焊接,能够获得质量优良和满足性能要求的不锈钢和铝合金导管钎焊接头,为航天、航空飞行器薄壁、小直径异材管路结构的工程应用提供了技术基础. 相似文献
9.
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
13.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
14.
15.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
16.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
19.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献