TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应

以内分泌干扰物阿特拉津为模型污染物,研究了TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应.结果表明,在H2O2存在条件下,金红石TiO2经可见光激发可持续稳定地产生.OH自由基,在Fe3+协同作用下,.OH自由基生成量急剧增加;TiO2能可见光催化H2O2降解阿特拉津,金红石TiO2显示出较锐钛矿TiO2及混晶TiO2(TiO2P25)更高的催化活性,反应60 min,阿特拉津的降解率可达40%;以Fe3+协同TiO2可见光催化H2O2降解阿特拉津时,反应效率显著加快,反应5 min即对阿特拉津的降解率达到100%,而金红石TiO2显示出更为明显的协同效应.     

Fe_2O_3-TiO_2光催化降解水中酸性橙Ⅱ研究

通过溶胶-凝胶法制备TiO2/Fe2O3复合半导体催化剂,用SEM、X-ray衍射仪对催化剂进行表征,设计了光催化降解反应装置以研究光催化降解水中酸性橙。探讨了Fe2O3-TiO2催化剂对可见光吸收性能,以及降解水中酸性橙Ⅱ的催化性能影响。实验结果表明:Fe2O3修饰的TiO2出现明显的红移,20%wFe2O3修饰的TiO2催化剂催化效率较高;TOC结果表明,低pH值条件有利于酸性橙Ⅱ的矿化。     

氮掺杂型纳米TiO2在可见光及太阳光下的光催化性能研究

采用钛酸四丁酯为原料,以氨水水解-沉淀法制备出了氮掺杂型纳米TiO2催化剂(N/TiO2),以XRD、XPS、UV-Vis等手段对其进行表征;并通过对偶氮染料橙黄G的降解反应,研究了N/TiO2在可见光及太阳光下的光催化性能,探讨了pH值、外加H2O2氧化剂对光催化降解率的影响,并与P25型纳米TiO2进行了对比.结果表明,在可见光下,N/TiO2对橙黄G具有较高的催化活性,反应150min后降解率可达96.29%,显著高于P25型TiO2(42.55%);在太阳光下,N/TiO2对橙黄G的光催化降解速率较快,反应60min降解率与P25型TiO2基本相同,分别为99.37%、99.94%;较低的pH值环境并适量添加H2O2可显著提高N/TiO2催化效率,在可见光及太阳光下的最佳pH值均为2～3,最佳H2O2加入量分别为0.5mL·L-1、1.5 mL·L-1.     

石墨烯/二氧化钛降解亚甲基蓝的研究

以钛酸丁酯和氧化石墨烯为前驱物,通过水热法制备石墨烯/二氧化钛(GR/TiO2)复合光催化剂。采用XRD、TEM和FT-IR等技术手段对GR/TiO2粉体的结构和形貌进行了表征。利用对亚甲基蓝光催化降解,考察了GR/TiO2的光催化降解能力,并研究了H2O2用量和p H等因素对光催化降解速率的影响。结果表明:复合催化剂中,TiO2为锐钛型晶体,粒径为25 nm左右,分散在薄纱状的石墨烯上;复合催化剂通过紫外光下光催化性能有所提高,对可见光产生响应,具有良好的稳定性;加入适量H2O2能提高反应速率,碱性条件下,对亚甲基蓝的降解效率更高。     

EDTA催化Fe3+/H2O2降解水中孔雀石绿

以孔雀石绿(malachite green, MG)为目标物,在pH=7的中性条件下,考察EDTA对Fe3 /H2O2降解水中孔雀石绿的影响,发现EDTA很大程度地促进了Fe3 /H2O2对孔雀石绿的降解. EDRA的加入可以使MG的脱色率由43%升至98.3%.在本实验条件下, EDTA的投加量增加5倍时, MG的脱色率上升40%.随着H2O2投量的增加, MG的脱色率显著上升.随着温度的升高, MG的脱色率显著上升.叔丁醇的加入抑制了EDTA对Fe3 /H2O2降解孔雀石绿的催化效果.总量相同H2O2的多次投加并未获得明显优于一次投加的去除效果. EDTA催化Fe3 /H2O2降解水中孔雀石绿并不遵循简单的羟基自由基机理,同时存在的中间价态铁的物种起着主要的氧化作用.随着反应的进行, EDTA被部分降解.     

UV/H_2O_2体系降解六氯苯动力学及其机理研究

对比了3种不同氧化方法对水中六氯苯(HCB)的去除效果,考察了HCB初始浓度、H2O2投加量及pH值对UV/H2O2降解HCB效果的影响。结果表明,3种工艺对HCB的降解效果是H2O2相似文献   

UV/H2O2降解羟苯甲酮反应动力学及影响因素

有机防晒剂随着日常使用不断进入环境中,成为一类新兴污染物.考察了UV/H2O2工艺对典型有机防晒剂羟苯甲酮(BP-3)的水相光化学降解特征,并对BP-3降解反应的影响因素包括初始BP-3浓度、H2O2浓度、UV光强、共存阳离子和阴离子、叔丁醇和腐殖酸投加量等进行了研究.结果表明,BP-3的降解速率常数随初始BP-3浓度升高而降低,随着H2O2浓度增大而增高,随着UV光强增强而增大;阴离子会在一定程度上降低反应速率,阳离子中Fe3+会产生类芬顿反应,促进生成·OH,对降解反应有显著的促进作用,投加叔丁醇和腐殖酸皆会抑制降解反应进行.采用每一对数减小级电能输入(EEo)指标对UV/H2O2工艺的电能利用效率进行了评价,Fe3+的加入显著减小了EEo.研究不同因素对UV/H2O2工艺降解效果的影响,可对实际工程中采用UV/H2O2去除苯甲酮类有机防晒剂提供参考.     

TiO2光催化联合技术降解苯酚机制及动力学

主要研究了TiO2光催化体系结合H2O2或外加电催化(EC)体系对苯酚催化降解效率的影响,评价比较TiO2/UV、H2O2/UV、TiO2/UV/H2O2、TiO2/UV/EC体系下苯酚降解机制及动力学.结果表明,TiO2/UV/H2O2和TiO2/UV/EC体系下苯酚降解效率明显高于TiO2/UV体系,当苯酚溶液pH值为6,TiO2质量浓度0.2 g·L-1,紫外光照2 h,光催化降解效果达到86%,当电流密度为12 mA·cm-2,则苯酚可达到100%去除.比较了不同催化体系下的能量利用率,苯酚降解15 min,TiO2/UV/EC体系能量利用率最大为0.030 6 g·(kW·h)-1,其能量消耗为0.0640 kW·h-1,说明采用TiO2/UV/EC体系能更多地利用能量降解苯酚.通过不同催化体系下中间产物分析,建立苯酚及其中间产物对苯二酚、邻苯二酚和苯醌的拟一级降解动力学模型,通过模型验证各催化体系下苯酚的降解历程,同时也说明了TiO2/UV/EC体系有利于苯酚及其中间产物的降解.     

ZnFe_2O_4/TiO_2光催化剂制备及乙酰甲胺磷降解性能研究

分别采用共沉淀法和溶胶-凝胶法制备了ZnFe2O4和掺杂ZnFe2O4的纳米级TiO2光催化剂,进行了XRD、TEM和UV visDRS表征,以卤素灯为光源对纳米TiO2降解水溶液中乙酰甲胺磷农药进行了研究。考察了反应液初始pH值、催化剂用量、H2O2用量对降解率的影响。实验结果表明,焙烧温度为400℃、掺杂量为0.5%的ZnFe2O4/TiO2纳米粉体降解效果最佳,在相同条件下,反应2h后农药降解率可比纯TiO2提高20%左右。正交实验优化了降解反应条件,在常温常压下,起始pH值为12、H2O2浓度为12mmol/L、催化剂浓度为0.5g/L、反应3h后,初始浓度为1.0×10-4mol/L的乙酰甲胺磷农药降解率可达61.2%。     

Fe~(3+)/TiO_2薄膜光催化降解UDMH废水的研究

研究Fe3+掺杂的TiO2薄膜对偏二甲肼废水光催化降解作用,考察了影响Fe3+掺杂的TiO2薄膜光催化降解偏二甲肼废水的效果的相关因素,结果表明最佳操作条件为:Fe3+掺杂TiO2薄膜的摩尔分数为0.5%,煅烧温度为500℃,煅烧时间为3h,催化降解反应时偏二甲肼废水为中性或弱碱性,催化降解温度为25℃。     

TiO2/PPY/Fe3O4的水热法制备及其光催化与磁回收性能

以化学氧化法制备的聚吡咯(PPY)包覆Fe3O4复合材料为磁核,用水热反应法(170℃, pH=7±0.2)在其表面负载了纳米Ti02,制成壳/壳/核结构的磁载二氧化钛光催化剂.并用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)、Zeta电位仪对催化剂的物相组成、形貌、表面性质、磁学性质以及磁核的表面电位进行了表征分析.以初始浓度为25mg/L的苯酚溶液为模拟污染物, 对其进行光催化降解以考察其催化活性;并以自制的磁回收装置考察其磁回收率.结果表明,所制备的Ti02粒径在4~7nm,具有混晶结构,其中锐钛矿占95.2%,金红石占4.8%;PPY对Ti02在磁核表面的负载具有促进作用,TiO2在PPY/Fe3O4表面负载牢固;催化剂TPF(nTiO2:n PPY:nFe3O4 =30:2.1:1)具有良好的壳/壳/核结构,其磁感应强度为40emu/g,具有超顺磁性;所制备的催化剂光催化降解苯酚符合假一级反应动力学方程,其中纯TiO2、P25、TPF反应速率常数K值分别为0.0279、0.0264、0.0252,TPF循环使用5次后K值为0.020,催化活性略有降低,循环使用平均回收率可达到90.35%. 该法制备的磁载Ti02光催化剂具有优良的催化活性和磁回收性能,具有良好的应用前景.     

TiO2/beads as a photocatalyst for the degradation of X3B azo dye

The feasibility of photocatalytic degradation of X3B azo dye by TiO2/beads photocatalyst was studied.The effects of parameters such as the amount of TiO2/beads,airflow ,as well as the concentrations of H2O2,Fe^3 ,Mg^2 and Na^ on the photocatalytic degradation of X3B azo dye were also studied.The results showed that 25mg/dm^3 X3B azo dye can be photocatalytically degraded completely by 30 min illumination with a 375W medium pressure mercury lamp.Adding a small amount of H2O2 or Fe^3 ,the efficiencies of photocatalytic degradation of X3B azo dye were increased rapidly.The mechanisms of the reaction and the role of the additives were also investigated.After 120 hours TiO2/beads showed no significant loss of the photocatalytic activity.     

TiO_2/beads as a photocatalyst for the degradation of X_(3B) azo dye

ＩｎｔｒｏｄｕｃｔｉｏｎＥｎｖｉｒｏｎｍｅｎｔａｌｐｒｏｔｅｃｔｉｏｎｅｘｐｅｒｔｓｉｎｍａｎｙｃｏｕｎｔｒｉｅｓｐａｙｈｉｇｈａｔｔｅｎｔｉｏｎｔｏｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒｗｉｔｈｄｙｅｏｒｗｉｔｈｄｅｅｐｃｈｒｏｍａ.Ｔｈｏｕｇｈａｔｐｒｅｓｅｎｔｂｉｏｄｅｇｒａｄａｔｉｏｎｉｓｕｓｅｄｉｎｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒ,ｔｈｅｃｏｎｃｅｎｔｒａｔｉｏｎａｎｄｃｈｒｏｍａｉｎｔｈｅｄｉｓｐｏｓｅｄｗａｔｅｒａｒｅｓｔｉｌｌｖｅｒｙｈｉｇｈａｎｄ…     

Free radical oxidation of spent radioactive organic solvent

ＦｒｅｒａｄｉｃａｌｏｘｉｄａｔｉｏｎｏｆｓｐｅｎｔｒａｄｉｏａｃｔｉｖｅｏｒｇａｎｉｃｓｏｌｖｅｎｔＪｉＸｉａｏｙｕａｎ，ＺｈａｏＢｉｎＩｎｓｔｉｔｕｔｅｏｆＮｕｃｌｅａｒＥｎｅｒｇｙＴｅｃｈｎｏｌｏｇｙ，ＴｓｉｎｇｈｕａＵｎｉｖｅｒｓｉｔｙ，Ｂｅ...     

纳米TiO_2光催化降解印染废水的研究

采用溶胶-凝胶法制备了纳米TiO2光催化剂,并用X射线衍射仪和扫描电镜对制备的TiO2进行结构表征。详细考察了照射时间、废水初始浓度、TiO2用量、pH、光源种类、H2O2、H2O2/Fe2+对实际印染废水的降解效果。研究结果表明:当反应时间为3h时,印染废水COD去除率为95.9%,脱色率达100%;印染废水的脱色率和COD去除率与印染废水的初始浓度成反比关系;TiO2光催化剂最佳用量为80mg/L;印染废水最佳降解的pH为6.0。当添加辅助氧化剂H2O2用量为600mg/L时,能进一步提高印染废水的COD去除率,特别是H2O2和Fe2+共同作用下,COD去除率达到99.%。     

Iron-doped Mn-Ce/TiO2 catalyst for low temperature selective catalytic reduction of NO with NH3

The catalysts of iron-doped Mn-Ce/TiO 2(Fe-Mn-Ce/TiO 2) prepared by sol-gel method were investigated for low temperature selective catalytic reduction(SCR) of NO with NH 3.It was found that the NO conversion over Fe-Mn-Ce/TiO 2 was obviously improved after iron doping compared with that over Mn-Ce/TiO 2.Fe-Mn-Ce/TiO 2 with the molar ratio of Fe/Ti = 0.1 exhibited the highest activity.The results showed that 96.8% NO conversion was obtained over Fe(0.1)-Mn-Ce/TiO 2 at 180°C at a space velocity of 50,000 hr 1.Fe-Mn-Ce/TiO 2 exhibited much higher resistance to H 2 O and SO 2 than that of Mn-Ce/TiO 2.The properties of the catalysts were characterized using X-ray diffraction(XRD),N 2 adsorption,temperature programmed desorption(NH 3-TPD and NOx-TPD),and Xray photoelectron spectroscopy(XPS) techniques.BET,NH3-TPD and NOx-TPD results showed that the specific surface area and NH3 and NOx adsorption capacity of the catalysts increased with iron doping.It was known from XPS analysis that iron valence state on the surface of the catalysts were in Fe3+ state.The doping of iron enhanced the dispersion and oxidation state of Mn and Ce on the surface of the catalysts.The oxygen concentrations on the surface of the catalysts were found to increase after iron doping.Fe-Mn-Ce/TiO2 represented a promising catalyst for low temperature SCR of NO with NH3 in the presence of H2 O and SO2.     

在TiO2催化剂上菲的光催化氧化反应研究

选择TiO₂ 粉末催化剂,在发射光谱为254 nm的15 W紫外灯照射下,反应液中Al3+,Fe3+和H2O₂ 浓度增加能提高菲的降解率;TiO₂ 表面载银量的增加能提高降解速度;TiO₂ 投入量在一定范围内随投入量的增加,光催化降解菲的速度也增加,但当投入量较多时又能降低降解速率;在酸性条件下,菲易被光催化降解;菲的起始反应浓度与反应速度成负一级反应动力学关系。      

Degradation of 2,4-dichlorophenol with a novel TiO2/Ti-Fe-graphite felt photoelectrocatalytic oxidation process

Degradation of 2,4-dichlorophenol(2,4-DCP)was studied in a novel three-electrode photoelectrocatalytic(PEC)integrative oxidation process,and the factors influencing the degradation rate,such as applied current,flow speed of O_2,pH,adscititious voltage and initial 2,4-DCP concentration were investigated and optimized.H_2O_2 was produced nearby cathode and Fe~(2 )continuously generated from Fe anode in solution when current and O_2 were applied,so,main reactions,H_2O_2-assisted TiO_2 PEC oxidation and E-Fenton reaction,occurred during degradation of 2,4-DCP in this integrative system.The degradation ratio of 2,4-DCP was 93% in this integrative oxidation process,while it was only 31% in E-Fenton process and 46% in H_2O_2-assisted TiO_2 PEC process.So,it revealed that the degradation of 2,4-DCP was improved greatly by photoelectrical cooperation effect.By the investigation of pH,it showed that this integrative process could work well in a wide pH range from pH 3 to pH 9.     

TiO2/PS/Fe3O4 光催化剂的低温制备及其光催化和磁回收性能

以聚苯乙烯(PS)包覆油酸修饰过的纳米Fe3O4为磁核,在低温(90℃)、中性(pH=7左右)条件下,制备了以PS为惰性隔离层的磁载TiO2光催化剂.用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)对催化剂的物相组成、形貌、表面性质、磁学性质进行了表征.以苯酚为模拟污染物,考察了其光催化活性,以自制的磁回收装置,考察其回收特性.结果表明,低温制备的TiO2为锐钛矿结构,平均粒径为2～5 nm,催化剂TiO2/PS/Fe3O4[其中物质的量比为n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]具有结构完整的壳/壳/核结构,TiO2在PS/Fe3O4表面负载牢固;光催化降解苯酚遵循一级反应动力学方程,TiO2/PS/Fe3O4[n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]的反应速率常数K=0.025 8,与纯TiO2的活性接近(K=0.026 2);循环使用5次后,反应速率常数仅降低0.003 4.所制催化剂具有较强的磁感应强度,平均回收率可达到92%以上.该低温水解法制备的磁载TiO2光催化剂具有良好的应用前景.     

Preparation, characterization, and photocatalytic activities of boron- and cerium-codoped TiO2

Boron- and cerium-codoped TiO2 photocatalysts were synthesized using modified sol-gel reaction process and characterized by X- ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, particle size distribution （PSD）, diffuse reflectance spectra （DRS）, and Brunauer-Emmett-Teller （BET）. The photocatalytic activities were evaluated by monitoring the degradation of dye Acid Red B （ARB）. The results showed that the prepared photocatalysts were mixed oxides mainly consisting of titania, ceria, and boron oxide. The structure of TiO2 could be transformed from amorphous to anatase and then to rutile by increasing calcination temperature; the transformation being accompanied by the growth of particle size without any obvious change in phase structure of CeO2. The XPS of B1.6Ce1.0-TiO2 prepared at 500℃ showed that a few boron atoms were incorporated into titania and ceria lattice, whereas others existed as B2O3. Cerium ions existed in two states, Ce^3＋ and Ce^4＋, and the atomic ratio of Ce^3＋/Ce^4＋ was 1.86. When boron and cerium were doped, the UV-Vis adsorption band wavelength showed an obvious shift toward the visible range （〈526 nm）. As the atomic ratio of Ce/Ti increased to 1.0, the absorbance edge wavelength increased to 481 nm. The absorbance edge wavelength decreased for higher cerium doping levels （Ce/Ti=2.0）. The particles size ranged from 122 to 255 nm with a domain at 168 nm （39.4%）. The degradation of ARB dye indicated that the photocatalytic activities of boron- and cerium-codoped TiO2 were much higher than those of P25 （a standard TiO2 powder）. The activities increased as the boron doping increased, whereas decreased when the Ce/Ti atomic ratio was greater than 0.5. The optimum atomic ratio of B/Ti and Ce/Ti was 1.6 and 0.5, respectively.